Search results for: 'Cutting m'

SEMI-AUTOMATIC BLANK FACE MASK EAR STRAP WELDING MACHINE
ULTRASONICALLY WELDS EAR STRAPS TO FACE MASK BLANKS
MASK DIMENSIONS: 175 x 95mm
CAPACITY: 60 PIECES PER MINUTE
POWER: 3 KW
DIMENSIONS: 1950mm L x 7000mm W x 1620mm H
WEIGHT: 200 KGS

AUTOMATIC FEEDING OF ELASTIC STRAP USED FOR EAR LOOPS
AUTOMATIC CUTTING OFF OF MANUAL LOADING AND UNLOADING
FLEXIBLE CONFIGURATION WITH EASY CONTROL

TWO SIZES OF MASKS CAN BE WELDED SIMULTANEOUSLY, SAVING TIME AND LABOR
MANUAL LOADING & UNLOADING
VERY EFFICIENT, LOW FAILURE RATE
WEIGHT OF MACHINE WHEN PACKED FOR AIR FREIGHT : 200 kgs
DIMENSIONS OF MACHINE WHEN PACKED FOR AIR FREIGHT: 2000 x 700 x 1650mm

QUANTITY: 1

Learn More

C-4394 SCHOTT & MEISSNER AIRLAID THERMOBONDING LINE, WORKING WIDTH 3400mm, YEAR 2014

SCHOTT & MEISSNER AIRLAID THERMOBONDING LINE
YEAR: 2014
WORKING WIDTH: 3400mm
ON THE MILL FLOOR BUT NEVER INSTALLED
CONSISTING OF:
1 BO 150 BALE OPENER
1 FO 125 FINE OPENER
1 TFF 30 TRANSPORT FAN
2 FC 150 FILLING CAGES
2 BO 150 BALE OPENERS
3 WPS 150 WEIGHING PLATE SYSTEMS
2 CMO 150 CONTINUOUS MIXING OPENERS
1 TFF 30 TRANSPORT FAN
1 LVB 150 LARGE VOLUME BLENDER
1 TFF 30 TRANSPORT FAN
1 DMX METAL DETECTOR
1 PO 175 BUFFER EQUIPMENT
1 TFF 30 TRANSPORT FAN
1 AWF 344 AIRLAID SYSTEM
1 TOPCON LP OVEN
DOUBLE BELT
2 X 3 M SECTIONS
2 X 2 M COOLING SECTIONS
1 CUTTING AND WINDING UNIT
UP TO 1 400 KG/H

QUANTITY: 1 LINE

Learn More

C-3782 NEEDLING LINE, WORKING WIDTH 3000mm TO 8000mm, YEAR 2010

OFFER 001
NEEDLING LINE

OFFER 002
MTV CA 1500 BALE OPENERS

OFFER 003
BEMATIC BHL 2500 OPENER

OFFER 004
BEMATIC BSS BHL 3000 CARD

OFFER 005
TEXNOLOGY CROSS-LAPPER

OFFER 006
TECTEX NS 5000/50 PRE-NEEDLE LOOM

OFFER 007
TECTEX ANS 5000/120 S FINISHING NEEDLE LOOM

OFFER 008
SICAM CAL/NT/2 DOUBLE CYLINDER THERMOBONDING CALENDER

OFFER 009
TECHNOPLANTS CUTTING AND WINDING UNIT

QUANTITY: 1 LINE

Learn More

REFERENCE NUMBER: M-5202 (1313VTYFXX12) L KB10 REBEAMER FOR ACETATE WITH DISK BRAKES - TSUDAKOMA QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: V-1849 BORDER MACHINE, CTL INTERNATIONAL, CTL-BT2_BT2V, YEAR 2002 MANUFACTURER: CTL INTERNATIONAL - (GARY BURGESS) BUILT 2X JUKI 1920 HEADS AUTOMATIC CUTTING-MEASURING-MATT BORDER MACHINS WITH HORIZONTAL CLOTH HANDLE INSTALLATION 120V YEAR: 2002 VERY GOOD CONDITION Learn More

REFERENCE NUMBER: J-2640
DYEING AND FINISHING PLANT FOR SALE

ITEM 001
THIES SAMPLE DYEING MACHINE
MODEL: MINISOFT SAMPLE
CAPACITY: 50 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 002
THIES DYEING MACHINE
MODEL ECOSOFT PLUS
3 PORT SPLIT/SPLIT
CAPACITY: 900 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 003
THIES DYEING MACHINE
MODEL: ECOSOFT PLUS
2 PORT SPLIT/SPLIT
CAPACITY: 600 KGS
YEAR: 1999
MICROPROCESSOR CONTROL
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 004
THIES DYEING MACHINE
MODEL ECOSOFT PLUS
1 PORT SPLIT/SPLIT
CAPACITY: 300 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: A460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 005
GASTON COUNTY DYEING MACHINE
MODEL: AQUAFLOW
2 PORT
CAPACITY; 250 KGS
YEAR: 1987
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING AND UNLOADING REEL
QUANTITY: 1

ITEM 006
THIES DYEING MACHINE
MODEL: SOFT TRD
2 TUBE
CAPACITY: 700 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 007 (also our J-2647)
LAFER OPEN WIDTH COMPACTOR MACHINE
MODEL: KSA 500 2400/2200
YEAR: 1998
LAFER TEXEN CONTROLS
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION BAR ENTRY TO LATTICE ROLL GUIDER
• OPERATOR’S PLATFORM
• PUP TENTER WITH KNIT ENTRY, VERTICAL PIN CHAIN, WITH PLATE GUIDES, RAIL OPENING, PINNING BRUSHES, PINS ONLY, WITH SUPPORT SECTION FOR THE FABRIC IN THE CENTER, AT 10’ THERE IS A STEAMING SECTION, TOTAL LENGTH OF THE TENTER IS 30’, WITH AUTOMATIC LUBRICATION FOR THE CHAIN
• KSA 500 COMPACTOR BENCH WITH TEXEN CONTROLS
• TENSIONLESS FABRIC CONVEYOR
• PLAITOR AND FABRIC SCRAY WITH OPTICAL LOAD SENSOR
• INLINE INSPECTION BATCHER MACHINE, WITHH A BACK LIGHTED BOARD, MANUAL CUT
• SCALE TO WEIGHT THE FABRIC
QUANTITY: 1

ITEM 008 (also our J-2648)
SANTEX TUBULAR 4-ROLL EXTRACTION PAD
MODEL: SANTASTRETCH PLUS 140
YEAR: 1998
COMPOSED OF TURNTABLE, DETWISTER, TUBULAR 4-ROLL PAD WITH WET SPREADERS, PLAITOR
WITH ADDITION TANKS FOR SOFTENER
REEL FABRIC PLAITOR EXIT
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

ITEM 009
SANTEX CONVEYOR DRYER FOR OPEN WIDTH AND TUBULAR FABRIC
MODEL: SANTASHRINK 4/5240
YEAR: 1998
SANTEX CONTROLS
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION BAR ENTRY TO LATTICE ROLL GUIDER TO
• (2) SANTEX 2-ROLL PADS, RUBBER OVER RUBBER, 102” WIDE x 12” DIAMETER, STAINLESS STEEL PAN, 10-TON PAD, SWING-AWAY PAN, TENSION BAR WITH 2 STAINLESS STEEL MIXING TANKS, 75 GALLONS EACH
• DRIVEN SCROLL ROLLS WITH EDGE GUIDE CONTROL, WIDTH 95”
• OPERATOR’S PLATFORM
• PUP TENTER WITH KNIT ENTRY 45°, YEAR 1998, VERTICAL PIN CHAIN, 30’ LONG WITH TANDEMATIC PLATE GUIDES, RAIL GUIDES, PINNING BRUSHES, GUIDE SUPPORT FOR THE FABRIC, FABRIC CONVEYOR TO ENTER BOTH TUBULAR OR OPEN WIDTH FABRIC TO
• CONVEYOR DRYER 100” WIDE, 5 ZONES, 3-PASS WITH MAXON BURNERS, 5 CIRCULATING FANS TO CONVEYOR BELT TO PLAITOR
• ALL MOTORS AND SANTEX CONTROLS AND MONITORS
QUANTITY: 1

ITEM 010
SANTEX AG TUBULAR COMPACTOR MACHINE
MODEL: SANTASPREAD 140
YEAR: 1998
SANTEX CONTROLS
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSIONS BAR ENTRY
• OPERATOR’S PLATFORM
• TENSION DEVICE
• DRIVEN SPREADER BARS
• STEAMING DEVICE
• TUBULAR COMPACTING BENCH
• FELT BLANKET ONTO THE CONVEYOR BELT
• PRECISION PLAITOR
• TABELTOP ELECTRONIC SCALE
QUANTITY: 1

ITEM 011
COMET NAPPER
MODEL: PEGSO-X4
YEAR: 1998
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
24 ROLLS WITH TURNING BARS FOR TUBULAR 90” WIDE
XYCOM CONTROLS
12-BAG COLLECTION SYSTEM AND PLAITOR
YEAR: 1996
QUANTITY: 1

ITEM 012
STENTEX TENTER FRAME
MODEL: STENTOTHERM 3300
YEAR: 1999
STENTEX CONTROLS
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION ENTRY TO TEXT-STAR TYPE GUIDER TO 2 ROLL PAD
• ADDITION TANK TOP SCRAY PAD TO TEXT-STAR TYPE GUIDER
• TWO ROLL PAD R/R 10 TON
• OPERATOR’S PLATFORM
• WORKING WIDTH 1800mm
• HORIZONTAL PIN CHAIN, KNIT ENTRY
• TANDEMATIC SPLITLEVEL DECURLERS
• OVERFEED
• PINNING BRUSHES
• STEAM BOX
• RAIL GUIDERS, 20 FEET ENTRY, 8 ZONES
• 80 FEET HOUSING
• SCREEN MONITORS
• GAS FIRED, MAXON OVEPAK 408 BURNERS
• HONEYWELL CONTROLS
• 3 FEET COOLING ZONE
• 2 COOLING CANS, SELVEDGE TRIMMERS
• PLIATOR, SCRAY
• ZONE IN LINE INSPECTION BATCHER
QUANTITY: 1

ITEM 013
ZIMMER ROTARY SCREEN PRINTING MACHINE
MODEL: R92-S153
YEAR: 1993
COMPOSED OF:
• TENSION BAR SKY ENTRY
• SCRAY
• CORINO BRUSH
• CORINO PRINT GUIDER
• ZIMMER PRINTER, 8 COLOR, 86” BLANEKT
• PRINT CONVEYOR DRYER, 30’ LONG, 3-ZONE, GAS FIRED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

ITEM 014
SAFETY SWITCH BULLET NOSE SLITTER
MODEL: CUTTING
WITH REEL FABRIC PLIATOR
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

Learn More

REFERENCE NUMBER: L-5092

EREMA RGA 160 TVE EXTRUDER, 6.3” SCREW (160mm), YEAR 2003

 

QUANTITY: 1

Learn More

P-5032 RIETER G30 RING FRAME WITH AUTODOFFER YEAR 1997 960 SPINDLES

RIETER
MODEL: G30
RING FRAME
YEAR: 1997
DOFFING: AUTOMATIC
NUMBER OF SPINDLES PER MACHINE: 960
SPINDLE GUAGE: 70mm
BOBBIN LENGTH: 210mm
DRAFTING MAKE: RIETER
DRAFTING TYPE: P3-1
CRADEL SIZE: SHORT – 36mm
TOP CLEARER ROLLER: NOT AVAILABLE
BOTTOM CLEARER ROLLER: NOT AVAILABLE
RING DIAMETERIN mm: 27/27/27
RING DIAMETER: 42mm
RING FLANGE: ONE
SPINDLE TYPE: PLUG
SPINDLE WHARVE: 21
SPINDLE DRIVE: 4 SPINDLE DRIVE
ABC RING: AVAILABLE
NUMBER OF CREEL ROWS: 5
TYPE OF GRIPPER: OUTER
YARN CUTTING: SPINDLE
BOBBIN CONVEYING: PEG TRAY
OHTC: AVAILABLE
OHTC MAKE: OTHER
INVERTER: AVAILABLE
EXHAUST AIR: DOWNWARDS
VOLTAGE: 440
FREQUENCY: 50

QUANTITY: 5

Learn More

REFERENCE NUMBER: C-4329
AHLSTROM SLITTER REWINDER, WIDTH 2600mm, YEAR 1981

NAME: AHLSTROM REWINDER / UNWINDER
WIDTH: 2600mm
CAPACITY SPEED: 1800 M/MIN
YEAR: 1981
REBUILD BELOIT CUTTING UNIT
TYPE: 30
FOR NONWOVENS, PAPER, LAMINATES
SPEED: 1800M/MIN

QUANTITY: 1

Learn More

M-6064 NONWOVEN NEEDLE FELT PUNCH PRODUCTION LINE, WIDTH 3000mm TO 5500mm, YEAR 2000

OFFER 001
NONWOVEN NEEDLE FELT LINE
NEEDLE PUNCH PRODUCTION LINE
FINAL FABRIC WIDTH: MAXIMUM 5500mm
YEAR: END OF 2000
BONDING: MECHANICAL (NEEDLING)
CAPACITY: ± 960 KG/H FOR A 250 G/M2 PRODUCT ON 4M WIDTH

OFFER 002
TEMAFA FIBRE OPENING SYSTEM
BALE OPENER

OFFER 003
SPINNBAU CARD FEEDING UNIT

OFFER 004
SPINNBAU ONE CARDING MACHINE
WORKING WIDTH: 3000mm

OFFER 005
AUTEFA CROSSLAPPER
WORKING WIDTH: 3000mm
LAYERING WIDTH: 6500mm

OFFER 006
DILO DI-LOOM OD-II 60 NEEDLE LOOM

OFFER 007
OUG-II 60 NEEDLE LOOM

OFFER 008
ONE ACCUMULATOR

OFFER 009
ONE WINDING AND CUTTING DEVICE

OFFER 010
ONE TEMAFA WEB EGE OPENING

OFFER 011
ALL SUCTION EQUIPMENT

OFFER 012
FULL CONTROL DESK & CONTROL CABINETS

OFFER 013
ONE PROCESS CONTROL SYSTEM

QUANTITY: 1 LINE

Learn More