Search results for: 'metal de'

REFERENCE  NUMBER:  G-0784

RIETER FDY  EXTRUSION EQUIPMENT FOR POLYPROPYLENE YEAR 1996/98

 

1. Machine m26/39:

Year 1996

For 1 fdy spinning line with 2+4 positions, each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  800 mm

Spinning pump capacity:  4x10 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  670 mm

Quench length:  1700 mm

Number of spin-finish pumps per position:  1

Capacity of spin-finish pump:  4x0.05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

Extruder for 4 positions Year 1998:

 

1 extruder type e1. 105-30m:

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  105 mm

-l/d ratio:  30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 58 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 95kw

-extruder frame

 

1 extruder measuring head, dowtherm vapour heated

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

Extruder for 2 positions Year 1998:

1 extruder type e1. 60-30

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  60 mm

-l/d ratio:  30

-barrel with

                electrical ceramic heaters

                6 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 17 kw

                inlet zone, water cooled

                insulation

-screw nitrited with maddock mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated year 1998

-measuring head comprising:

                insulation

Double pt100, one each for melt and dowtherm vapour temperature

                                pressure sensors for melt pressure

                burst disc for power switch-off at overpressure.

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam year 1998

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 25 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled level gauge

- vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

-max pressure in the spinpack:  350 bar

-design temperature:  320 °c

-spinneret outside dimensions:  95 mm

-bottom loading design

-bayonet locking, insert and tighten by turning 90°

-self sealing system

-sand or metal powder filtration, 3 cm filling depth

-wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 6 ccm/rev

Each spin pump system comprising

Individual drive motor with flange connection to the reduction gear

Hollow gear shaft for installation of spin pump shaft

Shaft with shear pin protection

Reduction ratio 1:80

Pump speed:  8-30 rev/min

Motor type:  synchronous ac-motor

Rated power:  500w at 50 cps

 

Quench air cabinets bsk 670/1700:

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                4 spin finish application nozzles

                1 yarn cutter / aspirator unit

                1 spin finish pump

                4 centring yarn guides

                4 intermingling units

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls year 1998:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speed range:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60 hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ±0.2 mm

Tube outside diameter:  106 ±0.4 mm

Tube length:  225 ±0.5 mm

 

Oil-mist lubrication unit:

Compressed air distribution station

Mobile aspirator guns with hoses

Electrical control equipment

-for electrical power

                general:  3 x 380v/50hz plus ground wire

                euro-standard:  3x400v 50 or 60hz plus ground wire

                maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation:  ±2%

 

Process control system (cif):

                fully integrated control system to control and monitor the entire spinning line.

                the central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control year 1998:

 

Spinning section:

Speed adjustment for the extruder motor is done via a dc-convertor

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor. While current flows, a voltage is inducted into the

Rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

2. Machines m27/ 28 / 30 year 1998:

For 3 fdy spinning lines each with 2 positions, and each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  1000 mm

Spinning pump capacity:  4x7.5 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  470 mm

Quench length:  1200 mm

Number of spin-finish pumps per position:  2

Capacity of spin-finish pump:  4x0.16 ccm/rev + 4x0,05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

 

1 extruder type e1. 60-30m

-nominal extruder capacity:  max 80 kg/h for pp

-screw diameter:  65 mm

-l/d ratio: 30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 22 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated:

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated:

Melt distribution system comprising:

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam:

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 18 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled

-level gauge

-vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

Max pressure in the spinpack:  350 bar

Design temperature:  320 °c

Spinneret outside dimensions:  95 mm

Bottom loading design

Bayonet locking, insert and tighten by turning 90°

Self sealing system

Sand or metal powder filtration, 3 cm filling depth

Wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 7.5 ccm/rev

Each spin pump system comprising

                individual drive motor with flange connection to the reduction gear

                hollow gear shaft for installation of spin pump shaft

                shaft with shear pin protection

                reduction ratio:  1:80

                pump speed:  8-30 rev/min

                motor type:  synchronous ac-motor

                rated power:  500w at 50 cps

 

Quench air cabinets bsk 470/1200

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                2 spin finish application nozzles per end

                1 yarn cutter / aspirator unit

                2 spin finish pump

                4 centring yarn guides

                4 pre-intermingling jets

                4 intermingling units

                1 additional operator panel between duo1 and duo 2.

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speedrange:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60

Hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094:

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ± 0.2 mm

Tube outside diameter:  106 ± 0.4 mm

Tube length:  225 ± 0.5 mm

 

Compressed air distribution station:

Mobile aspirator guns with hoses

Electrical control equipment

For electrical power

                general : 3 x 380v/50hz plus ground wire

Euro-standard: 3x400v 50 or 60hz plus ground wire

Maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation: ±2%

 

Process control system (cif):

Fully integrated control system to control and monitor the entire spinning line.

The central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control:

Spinning section.

Speed adjustment for the extruder motor is done via a dc-convertor.

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor.

While current flows, a voltage is inducted into the rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

HOURLY PRODUCTION:

FOR 150 DENIER @ 3500 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 3.5 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 14 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 28 KG/HOUR AND M39 = 56 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 28 KG/HOUR EACH.

(AS PER OUR PEOPLE AT THE EXTRUSION PLANT, THEY WERE RUNNING TRIALS TO PRODUCE THE 150 DENIER @ 4000 MPM WINDER SPEED)

 

FOR 300 DENIER @ 3600 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 7.2 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 28.8 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 57.6 KG/HOUR AND M39 = 115.2 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 57.6 KG/HOUR EACH.

 

FOR 600 DENIER @ 2200 MPM WINDER SPEED, (SPEED LIMITATION DUE TO EXTRUDER CAPACITY) THE HOURLY PRODUCTION IS 8.8 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 35.2 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 70.4 KG/HOUR AND M39 = 140.8 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 70.4 KG/HOUR EACH.

 

MACHINE HAS BEEN PARTIALLY DISASSEMBLED (EXTRUDERS AND SPINBEAMS HAVE BEEN TAKEN DOWN TO GROUNDFLOOR) REST OF THE EQUIPMENT STILL TO BE DISASSEMBLED

Learn More

REFERENCE NUMBER: T-6550

MEDICAL PROTECTIVE CLOTHING BLOOD SYNTHETIC PENETRABILITY TESTER

 

TECHNICAL SPECIFICATIONS AND CONFIGURATION:

1. THE INSTRUMENT ADOPTS AN AIR SOURCE THAT CAN PROVIDE (0.5 ~ 30±0.1) KPA PRESSURE TO CONTINUOUSLY PRESSURIZED THE SAMPLE, WHICH IS NOT RESTRICTED BY THE SPACE OF THE TEST SITE;

2. THE AIR PRESSURE RANGE CAN BE ADJUSTED FREELY, AND THE ADJUSTMENT RANGE (0.5 ~ 30) KPA;

3. COLOR TOUCH SCREEN DISPLAY AND OPERATION;

4. THE SAMPLE CLAMPING PAD IS PROCESSED WITH IMPORTED SPECIAL ALUMINUM PROFILES, WHICH IS LIGHT IN MATERIAL, CLEAN IN SURFACE AND NEVER RUSTS.

5. THE INSTRUMENT ADOPTS IMPORTED SPECIAL ALUMINUM WIRE DRAWING PANEL, EQUIPPED WITH METAL KEYS, SENSITIVE OPERATION, NOT EASY TO DAMAGE;

6. CLAMPING DEVICE FOR INSTRUMENT SAMPLES, EQUIPPED WITH LOCKING PROTECTION, TO PREVENT THE SYNTHETIC BLOOD FROM SPLASHING AROUND;

7. CLAMPING FORCE IS ACCURATE AND RELIABLE;

8. THE TEST TANK IS EQUIPPED WITH A SPECIAL PLACEMENT DEVICE, WHICH IS CONVENIENT FOR CUSTOMERS TO OPERATE;

9. THE TEST TANK IS PROCESSED WITH SPECIAL 316 STAINLESS STEEL, AND THE TOP IS EQUIPPED WITH A SPECIAL COVER FOR HIGH TRANSPARENT PROTECTION;

10. THE WASHER BELOW THE SAMPLE IS MADE OF HIGH-QUALITY PTFE MATERIAL AFTER SPECIAL PROCESSING;

11. SQUARE METAL BLOCK NET: OPEN SPACE ≥50°%; BENDING ≤5mm AT 30KPA;

12. INSTRUMENT TIME CONTROL ACCURACY ≤01 SECONDS;

13. THE SHELL OF THE INSTRUMENT IS MADE OF HIGH-QUALITY METAL BAKING PAINT, WHICH IS BEAUTIFUL AND GENEROUS.

14. EQUIPPED WITH PRINTER INTERFACE, CONNECTED TO THE PRINTER CAN DIRECTLY PRINT DATA REPORTS.

 

TECHNICAL PARAMETERS:

1. SAMPLE SIZE: 75mm X 75mm

2. TEST AREA: 28.26 SQUARE CENTIMETERS

3. AIR PRESSURE ADJUSTMENT RANGE (0.5 ~ 30) KPA

4. EXTERNAL SIZE: 500mm X 500mm X 500mm (L X W X H)

5. WEIGHT OF THE INSTRUMENT: 40 KG

6. POWER SUPPLY: AC220V, 50HZ,SCOPE OF SUPPLY: 1. ONE MAIN MACHINE; 2. TWO PTFE GASKETS; 3. TWO ORDINARY WASHERS; 4. ONE METAL BLOCKING NET; 5. A SET OF SPECIAL LOCKING TOOLS; 6. ONE HIGH-QUALITY SILENT AIR PUMP, [NOTE: SAFETY PRODUCTION LICENSE IS NOT INCLUDED]. 7. EQUIPPED WITH PRINTER INTERFACE; 8. ONE SAMPLE TEMPLATE; 9. ONE PRODUCT CERTIFICATE; 10. ONE COPY OF PRODUCT OPERATION MANUAL.

 

OPERATION INSTRUCTION:

INSERT THE AIR PUMP OUTPUT PIPE INTO THE OIL AND WATER SEPARATOR OF THE INSTRUMENT AS REQUIRED (PRESSURE 0.1-0.3MPA).

AFTER SWITCHING ON THE POWER, THE STARTUP INTERFACE (NAME OF THE DEVICE) IS DISPLAYED.

PRESS THE "ENTER" BUTTON TO ENTER THE TEST INTERFACE, AS SHOWN IN THE FOLLOWING FIGURE:

CLICK "SETTING” BUTTON, GET INTO PARAMETER SETTING SCREEN, AS BELOW THIS SCREEN CAN SET THE SYSTEM TIME, DATE AND TESTING TIME, AFTER SETTING, CLICK "SAVE” BUTTON TO KEEP THE SETTING DATA. (NOTE: IT REQUIRES 5 MINUTES IN THE STANDARD)

 

QUANTITY: 1

Learn More

M-6053 SPUNBOND PRODUCTION LINE, WORKING WIDTH 4040mm TO 4500mm

OFFER 001
SPUNBOND PRODUCTION LINE
WORKING WIDTH: 4040mm
WEIGHT: 130 TO 250 G/M2

OFFER 002
POLYMER CLEANING GROUP

OFFER 003
CRYSTALLIZING GROUP

OFFER 004
DRYING GROUP

OFFER 005
PNEUMATIC CONVEYING SYSTEM

OFFER 006
EXTRUDER HOPPER

OFFER 007
EXTRUDER

OFFER 008
FILTERING UNIT

OFFER 009
MELT TRANSFER LINE

OFFER 010
SPINNING BEAM

OFFER 011
SPINNING PACKS

OFFER 012
FILAMENTS QUENCHING SYSTEM

OFFER 013
FILAMENTS DRAWING AND DISTRIBUTION SYSTEM

OFFER 014
WEB FORMING CONVEYOR BELT

OFFER 015
CREEL FOR APPLICATION OF REINFORCING FILAMENTS

OFFER 016
PRE-NEEDLING MACHINE

OFFER 017
NEEDLING MACHINE

OFFER 018
THERMOSETTING UNIT

OFFER 019
OUTLET CALENDER

OFFER 020
FOULARD

OFFER 021
BINDER PREPARATION SYSTEM

OFFER 022
DRYER

OFFER 023
OUTLET CALENDER

OFFER 024
AUTOMATIC WINDER

OFFER 025
AIR COMPRESSORS (FOR FILAMENTS STRETCHING EJECTORS)

OFFER 026
DIATHERMIC OIL HEATING SYSTEM

OFFER 027
CHILLED WATER CIRCULATION AND GENERATION SYSTEM

OFFER 028
EQUIPMENT FOR CLEANING CYCLE, SPECIAL TOOLS

OFFER 029
FIBRE DUST RECOVERY SYSTEM

OFFER 030
EDGES RECOVERY SYSTEM

OFFER 031
SPINNING SECTION STEEL STRUCTURE

OFFER 032
DISTRIBUTION ELECTRIC CABINETS

OFFER 033
PROCESS ELECTRIC SYSTEM OF EXISTING MACHINES ACCORDING TO THE ACTUAL LAYOUT

OFFER 034
CABLES AND CABLING MATERIALS

QUANTITY: 1 LINE

Learn More

REFERENCE NUMBER: T-6286 EREMA INTAREMA 1006 TVE PLUS RECYCLING LINE, YEAR 2017 EREMA INTAREMA 1006 TVE PLUS RECYCLING LINE YEAR 2017 LIKE NEW 70mm EXTRUDER FOR FILM 250 KG/HOUR DEGASSING SYSTEM METAL DETECTOR MANUALS INCLUDING: FEED BELT CONVEYOR DOUBLE LAYER ALL METAL DETECTOR REEL FEEDER DEVICE INTAREMA 1006TVE PLUS PROCESS COMBINATION INPUT SLIDE POWERED EXHAUST SYSTEM WATER SYSTEM FOR VACUUM PUMP EREMA BACK FLUSH FILTER SET DIE FACE PELLETIZING SYSTEM QUANTITY: 1 Learn More

M-6063 AIRLAY / THERMOBONDING PRODUCTION LINE, WIDTH 2500mm TO 2700mm, YEAR 1975 TO 2012

OFFER 001
AIRLAY / THERMOBONDING PRODUCTION LINE
WORKING WIDTH: 2500mm

OFFER 002
CROSA PERINO BLENDING BOXES
YEAR: 1990 (OVERHAULED 2011)
CAPACITY: 750 KG EACH

OFFER 003
HDB CARDING WILLOW
YEAR: 1975

OFFER 004
MESUTRONIC METAL DETECTOR
YEAR: 2007

OFFER 005
MESUTRONIC METAL SEPARATOR
YEAR: 2007

OFFER 006
FALLGARTER HOPPER FEEDER
YEAR: 1975

OFFER 007
ROLANDO HOPPER FEEDER
YEAR: 1985 (OVERHAULED 2003)

OFFER 008
HERGETH HOLLINGSWORTH FINE OPENER
YEAR: 1981

OFFER 009
STUMMER CONTINUOUS CLEANER
YEAR: 2007

OFFER 010
HERGETH HOLLINGSWORTH AIRLAY FEEDING
YEAR: 1981 (OVERHAULED 2012)
WORKING WIDTH: 2500mm

OFFER 011
OLBRICH AIRLAY CARD
YEAR: 2010
WORKING WIDTH: 2500mm

OFFER 012
STRAHM OVEN
YEAR: 2008
WORKING WIDTH: 2700mm

OFFER 013
OLBRICH LONGITUDINAL CUTTING
YEAR: 2004
WORKING WIDTH: 2600mm

OFFER 014
KZE CROSSCUTTING
YEAR: 2012
WORKING WIDTH: 2600mm

QUANTITY: 1 LINE

Learn More

M-6055 NONWOVEN NEEDLE FELT LINE, WIDTH 4300mm, YEAR 1970 TO 2004

OFFER 001
NONWOVEN NEEDLE FELT LINE – RENEWED 3 YEARS AGO
WORKING WIDTH: 4300mm

OFFER 002
HERGETH BALE OPENER
YEAR: 1986
WORKING WIDTH: 1000mm

OFFER 003
OILING UNIT
TANK CAPACITY: 250 LITRES

OFFER 004
AUGUST PROTT FAN FOR FIBER TRANSPORT
POWER: 7.5 KW

OFFER 005
TERMO GORING KERR METAL DETECTOR AND METAL SEPARATOR
YEAR: 2004

OFFER 006
TEMAFA MIXING BIN

OFFER 007
FOR FAN FOR FIBER TRANSPORTATION

OFFER 008
FOR CHUTE FEED WITH MOVEABLE CONDENSOR
WORKING WIDTH: 2500mm

OFFER 009
WEB DENSITY MEASURING AND AUTOMATIC ALIGNING

OFFER 010
FOR CARDING MACHINE
WORKING WIDTH: 2500mm

OFFER 011
ASSELIN CROSSLAPPER
YEAR: 1984
INPUT WIDTH: 2500mm

OFFER 012
FEHRER FIRST NEEDLE LOOM
YEAR: 1973
WORKING WIDTH: 4800mm

OFFER 013
UNWINDING FOR PRELIMINARY WEB

OFFER 014
CONVEYOR SYSTEM FOR WEB TRANSPORTATION TO SECOND NEEDLE LOOM

OFFER 015
FEHRER SECOND NEEDLE LOOM
YEAR: 1970
WORKING WIDTH: 4400mm

OFFER 016
FEHRER THIRD NEEDLE LOOM
YEAR: 1973
WORKING WIDTH: 4800mm

OFFER 017
BENEDETTI & CALAMAI TRIMMING AND WINDING UNIT
YEAR: 1995
TABLE WIDTH: 5500mm

OFFER 018
LAROCHE EDGE TRIM OPENER

QUANTITY: 1 LINE

Learn More

C-5163 SPINNING MILL BLOW ROOM TRÜTZSCHLER & BLOW ROOM RIETER

ITEM 001
CONDENSER LVSA-375
YEAR: 1997
QUANTITY: 1

ITEM 002
MULTIMIXER MCM 6 /1200
YEAR 1997
CVT-4 / 1200
YEAR: 1997
QUANTITY: 1

ITEM 003
JOSSI THE VISION SHIELD FIBER DETECTOR EA-33-S
YEAR: 2002
QUANTITY: 1

ITEM 004
DUSTEX DX 385
YEAR: 1997
QUANTITY: 1

ITEM 005
JOSSI THE SHIELD HIGH PERFORMANCE FIRE DETECTOR
TYPE D-11-250
YEAR: 2005
QUANTITY: 1

ITEM 006
TRÜTZSCHLER FAN
QUANTITY: 3

ITEM 007
MRO METAL DETECTOR
QUANTITY: 1

BLOW ROOM RIETER
ITEM 008
UNIFLOC A 1/2
LENGTH USEFUL 20M
YEAR: 1991
QUANTITY: 1

ITEM 009
FINE OPENER FOR WASTE
WIDTH 0.80M
MODEL: B 3/4S
YEAR: 1991 + APRON 4M
QUANTITY: 1

ITEM 010
MONOTAMBOR B 4/1
YEAR: 1991
QUANTITY: 1

ITEM 011
UNIMIX B 7/3R
YEAR: 1991 (OPENER)
QUANTITY: 1

ITEM 012
ERM B 5/5
YEAR: 1989
QUANTITY: 2

ITEM 013
JOSSI FIRE DETECTOR D-11-250
YEAR: 2005
QUANTITY: 1

ITEM 014
JOSSI THE VISION SHIELD DETECTOR
FIBER DETECTOR TYPE EA-33-S
YEAR: 2002
QUANTITY: 1

ITEM 015
CARDS TRÜTZSCHLER DK-803
YEAR: 1997
COILER KH 950-1200
AUTOMATIC REVOLVER
FEEDING FBK-533
QUANTITY: 3

ITEM 016
CARDS TRÜTZSCHLER DK-903
YEAR: 2003
1 COILER KH 600-1200
2 COILER KH 450-1200
AUTOMATIC REVOLVER
FEEDING DKF
QUANTITY: 3

ITEM 017
DRAW FRAME TRÜTZSCHLER HSR-1000
YEAR: 2003
DELIVERY 18” (450X1000)
CREEL 8 CANS
SLIVER MONITOR
AUTOLEVELLER
QUANTITY: 2

ITEM 018
ROVING FRAME SIMPLEX ZINZER 670
YEAR: 2003
DRAFT PK 1500
120 SPINDLES
CAPACITY BOBBIN 16”X6”
DRIVER CREEL
COLLECTIVE ASPIRATION
INDIVIDUAL BLOWER ELECTRO-JET
QUANTITY: 2

ITEM 019
AUTOMATIC TRANSPORT INSTALLATION FOR BOBBINS ELECTRO-JET
YEAR: 2003
FOR 8 RING SPINNING FRAME
1,200 SPINDLES
QUANTITY: 2

ITEM 020
INSTALLATION LTG
YEAR: 2003
5 PARTS
WASTE COLLECTING
AIR SYSTEM
QUANTITY: 1

ITEM 021
INSTALLATION LTG
YEAR: 2003
3 PARTS
WASTE COLLECTING
AIR SYSTEM
QUANTITY: 1

ITEM 022
INSTALLATION LTG
YEAR: 2003
5 PARTS
WASTE COLLECTING
CARDING FILTRATION
QUANTITY: 1

ITEM 023
RING SPINNING FRAME ZINZER RM 351
YEAR: 2002 (4)
YEAR: 2003 (1)
1200 SPINDLES
GAUGE 70MM
DRAFT PK 2500
RING 42MM
TUBE 220MM
COWEMAT
COLLECTIVE ASPIRATION
INDIVIDUAL BLOWER
ELECTRO-JET WITH AUTOMATIC UNLOADING
TOTAL LENGTH 47M
QUANTITY: 5

ITEM 024
WINDER SCHLAFHORST 338 RM
YEAR: 2003
COLOR WHITE
60 POSITIONS
MAGAZINE FEEDING 6 TUBES
2 ROBOTS
WAXING
AUTOMATIC CONE CHANGE
TK-840
CLEARER LOEPFE
DELIVERY 4.20 X 6”
INDIVIDUAL BLOWER
QUANTITY: 2

ITEM 025
AUTOCORO SCHLAFHORST SE-11 ACO-288
YEAR: 2001
216 ROTORS
INFORMATOR
DELIVERY CYLINDRICAL SLUBIER PINTER
ROTOR Ø 28-36-40MM
ROLLERS B-174
CLEARERS COROLAB
WAXING
2 ROBOTS CONE CHANGE ROBOTS PIECERS
QUANTITY: 1

ITEM 026
AUTOCORO SCHLAFHORST SE-9
YEAR: 1998
216 ROTORS
2 ROBOTS
WAXING
COROLAB
INFORMATOR
QUANTITY: 1

ITEM 027
POWER 380V/50HZ
SPLIT SALE POSSIBLE
CONDITION COMPLETED
UNIT PRICE EX-WORKS EURO

Learn More

REFERENCE NUMBER: T-6919 RAMISCH KLEINEWEFERS CALENDER, WORKING WIDTH 1800mm, YEAR 1991 RAMISCH KLEINEWEFERS CALENDER YEAR 1991 WORKING WIDTH 1800mm 3 CYLINDERS 2 STEEL 1 RACOLAN UPPER AND LOWER CYLINDERS ARE ELECTRIC HEATED WITH METAL AND SEWING DETECTOR TEMP. 190 °C WORKING PRESS 50 BAR MACHINES ARE IN EXCELLENT RUNNING CONDITION QUANTITY: 1 Learn More

REFERENCE NUMBER: T-6855 AUTEFA, DILO, SPINNBAU COMPLETE NONWOVEN LINE BRAND: AUTEFA, DILO, SPINNBAU SHORT DESCRIPTION: COMPLETE NONWOVEN LINE ITEM 001 SINGLE DOFFER CARD BY “BESSI” - ITALY YEAR 1966 - WORKING WIDTH 2500mm - HOPPER-FEEDER WITH SCALE (WEIGHPAN) AND TOP SILO - INLET UNIT WITH ROLLERS - BREAST UNIT DIAMETER 1500mm WITH 3 PAIRS WORKERS/ STRIPPER (ORIGINALLY EQUIPPED WITH 5 PAIRS, UNUSED 2 PAIRS STILL AVAILABLE) - FANCY ROLL - TRANSPORT ROLL DIAMETER 1200mm - SWIFT DIAMETER 1500mm WITH 3 PAIRS WORKERS/ STRIPPER (ORIGINALLY EQUIPPED WITH 5 PAIRS, UNUSED 2 PAIRS STILL AVAILABLE) - DOFFER DIAMETER 1500mm WITH FLY-COMB - FLEXIBLE AND RIGID METALLIC WIRES IN EXCELLENT CONDITIONS QUANTITY: 1 ITEM 002 CROSS-LAPPER BY “MAK-AUTEFA” - GERMANY MODEL 101-42 YEAR 1965 - INLET WORKING WIDTH 2500mm - EXIT WORKING WIDTH 3000mm QUANTITY: 1 ITEM 003 PRE-NEEDLER BY “DILO” - GERMANY MODEL NFZ 3000 YEAR 1967 - WORKING WIDTH 3000mm - 2 NEEDLE BOARDS WITH TOTALLY 3000 NEEDLES / LIN MT - WITH BATT INLET UNIT QUANTITY: 1 ITEM 004 FINISH NEEDLERS BY “DILO” MODEL OD II 25 YEAR 1979 EACH - WORKING WIDTH 2500mm EACH - EACH ONE WITH 2 NEEDLE BOARDS WITH TOTALLY 5000 NEEDLES / LIN MT QUANTITY: 2 ITEM 005 TRANSVERSAL CUTTER BY “SPINNBAU-AUTEFA” - GERMANY. YEAR 1973 - WORKING WIDTH 2500mm QUANTITY: 1 ITEM 006 LONGITUDINAL CUTTER ITALIAN MAKE + ROLL WINDER ITALIAN MAKE ON ELECTRONIC WEIGHTING CELLS. WORKING WIDTH 2500mm QUANTITY: 1 ITEM 007 ROLLS LIFTING CRANE QUANTITY: 1 ALL ELECTRIC MOTORS AND CONTROL PANELS 400 V / 50 Hz Learn More

REFERENCE NUMBER: T-6852 AUTEFA, DILO, SPINNBAU NEEDLE-PUNCHING COMPLETE LINE BRAND: AUTEFA, DILO, SPINNBAU SHORT DESCRIPTION: NEEDLE-PUNCHING COMPLETE LINE 3° NEEDLE-PUNCHING COMPLETE LINE (1970 CA.) COMPOSED OF: 1 SINGLE DOFFER CARD BY “BESSI” WORKING WIDTH 2500mm - HOPPER-FEEDER “TEMAFA” WITH SCALE (WEIGHPAN) AND TOP SILO - BREAST UNIT DIAMETER 1500mm WITH 7 PAIRS WORKERS/STRIPPER DIAMETER 220/74, RIGID METALLIC WIRES STILL USABLE 60% APPROX. - TRANSPORT ROLL DIAMETER 1285mm, RIGID WIRES STILL USABLE FOR 80% APPOX - SWIFT DIAMETER 1500mm, 6 PAIRS WORKERS/STRIPPER DIAMETER 215/74, SWIFT WITH RIGID WIRES STILL USABLE 90% CA., FLEXIBLE WIRES FOR WORKERS STILL USABLE 80% APPROX - DOFFER DIAMETER 1500mm, FRIGID WIRES STILL USABLE 90% APPROX. - FLY-COMB 1 CROSSLAPPER “MAK-AUTEFA”, INLET WORKING WIDTH 2500mm, EXIT WORKING WIDTH 3000mm 1 PRE-NEEDLER “DILO” NFZ25, MATR. 2387/1965, NO. 2580 NEEDLES/LM WITH MOBILE STRIPPER PLATE FOR HEAVY FELTS 1500 GRS/SQM AND/OR VOLUMINOUS FIBERS 2 LONGITUDINAL CUT “MACCHI” 1 TRANSVERSAL CUT “SPINNBAU” 1 WINDER IN WEIGHTING CELLS (METTLER) QUANTITY: 1 Learn More