Search results for: 'point m'

TT-6034 SUCKER MULLER CONVERTED INTO PLC, 3600mm, YEAR 2014 SUCKER MULLER CONVERTED INTO PLC BY ANUP INDUSTRIES YEAR 2014 QUANTITY: 1 Learn More

AA-1189 CONTAINER LOADING CRANE TECHNICAL PARAMETERS: TYPICAL QUAYSIDE CRANE 1. A: GANTRY SPAN: 15000 TO 35000mm 2. C: BACKREACH: 0 TO 25000mm 3. E: CLEARANCE UNDER SILL BEAM: 12000 TO 18000mm 4. G: TRAVEL WHEEL GAUGE: 18200mm 5. H: BUFFER TO BUFFER: 27000mm 6. WHEEL SPACING: 1000 TO 2000mm 7. WHEELS PER CORNER (DEPENDS ON REQUIRED WHEEL LOADS): 6/12 – SEASIDE 8. WHEELS PER CORNER (DEPENDS ON REQUIRED WHEEL LOADS): 6/12 – LANDSIDE 9. MAX. WIDTH TROLLEY AND MAIN BEAM/BOOM: 7600mm Learn More

TT-6743 TECH LIGHTING XTRACOAT MINI UV COATER QUANTITY: 1 Learn More

YY-2735 LANDING CRAFT MECHANIZED (LCM-8) QUANTITY: 1 Learn More

YY-2424 USED NGR REGRANULATION LINE for BOPP FILM, FLUFF, LUMPS, MDO WASTE 900 TO 1000 KG PER H OVERCONSUMPTION: 500 KW OUTPUT: 1000 KGS PER HOUR INTENDED FOR THE FOLLOWING WASTE: OUTPUT; BOPP FILM, FLUFF, LUMPS, MDO WASTE: 900 TO 1000 KG/H; CPP FILM, FLUFF, LUMPS: 900 TO 1000 KG/H; PERFORMANCE IS PROVIDED FOR REFERENCE ONLY. THE CAPACITY OF THE DEVICE DEPENDS ON THE PROPERTIES OF THE MATERIAL, E.G. MOISTURE CONTENT, PRINTING, WEIGHT, MELT INDEX, CONTAMINATION AND DEGREE OF FILTRATION. AVERAGE POWER CONSUMPTION: 500 KW; AVERAGE COOLING WATER DEMAND: 668 L/MIN; AVERAGE FRESH WATER CONSUMPTION: 34 L/H; MAXIMUM COMPRESSED AIR CONSUMPTION: 100 L/MIN. THE VALUES GIVEN ABOVE ARE ONLY REFERENCE VALUES AND MAY DIFFER FROM THE VALUES FINAL VALUES OBTAINED AFTER CALIBRATION OF THE DEVICE. THIS DATA SHOULD NOT BE USED FOR PLANNING. Learn More

TT-1698 TOSHIBA DUAL FUEL INLET STEAM TURBINE & GENERATOR POWER PLANT (NEVER USED), 215 MW, 50 Hz, YEAR 2008 RATING: 215 MW TYPE: STEAM TURBINE & GENSET BRAND: TOSHIBA MODEL: SGLFLOW CONDENSING FUEL: DUAL FUEL 50 Hz YEAR: 2008 QUANTITY: 1 Learn More

YY-1140 RESPIRATORY RESISTANCE TESTER, FLOWMETER RANGE 0 L/MIN~100L/MIN, FLOWMETER RANGE ACCURACY ±2% DETAILS: THE RESPIRATORY RESISTANCE TESTER IS SUITABLE FOR DETERMINING THE INHALATION RESISTANCE AND EXHALATION RESISTANCE OF RESPIRATORS AND MASK PROTECTIVE PRODUCTS UNDER SPECIFIED CONDITIONS, AND FOR THE RELATED TESTING AND INSPECTION OF COMMON MASK PRODUCTS BY MANUFACTURERS OF NATIONAL LABOR PROTECTION ARTICLE INSPECTION AGENCIES. STANDARD: GB2626-2006,GB/T32610-2016. Learn More

J-3004 FIBRILLATED RAFFIA TAPE EXTRUSION LINE – NEW, 120mm PP FIBRILLATED YARN EXTRUDER LINE MODEL: NOVASTAR-120 EXTRUSION LINE FOR PRODUCTION OF PP FIBRILLATED YARN RAW MATERIAL: PP GRANULE FINISHED PRODUCTS: NON-TWISTED TAPE YARN, FIBRILLATED YARN FOR TWINE RANGE OF PRODUCT: 10,000 TO 30,000 DENIER 10000 DENIER APPROXIMATELY 17 TO 19 YARN 16000 DENIER APPROXIMATELY 11 TO 12 YARN 22000 DENIER APPROXIMATELY 8 TO 9 YARN 28000 DENIER APPROXIMATELY 6 TO 7 YARN 32000 DENIER APPROXIMATELY 5 TO 6 YARN EXTRUSION THROUGHPUT: 300 KG PER HOUR EXTRUSION CAPACITY: 180 TO 250 KG PER HOUR (PRODUCT CAPACITY DEPEND ON FILAMENT SIZE) EXTRUDER SCREW DIAMETER: Ø 120mm T-DIE WIDTH: 1300mm TAKE-OFF ROLLER WIDTH: 1200mm TAKE-OFF LINE SPEED: 160 METERS PER MINUTE (MAXIMUM) OPERATION SIDE: RIGHT TO LEFT, OR LEFT TO RIGHT Learn More

MAINLY USED FOR VISUAL FIELD TESTING OF MASKS AND RESPIRATORS, WHICH IS USEFUL FOR MASK AND RESPIRATOR MANUFACTURERS, QUALITY SUPERVISORS, SCIENTIFIC RESEARCH, AND FOR TESTING PRIOR TO SELLING MASKS.

FEATURES:
1. THE EQUIPMENT IS COMPOSED OF A SEMI-ARC BOW, RECORDING DEVICE, SEAT FRAME AND TEST HEAD DIE.
2. SEMI-ARC BOW: THE RADIUS IS 300 TO 340 mm
CAN BE ROTATED AROUND THE HORIZONTAL RADIUS PLANE PASSING THROUGH THE POINT 0°, AND A SCALE EXTENDING TO THE 90° ARC BOW EVERY 5° FROM 0° ON BOTH SIDES, EQUIPPED WITH SLIDING WHITE VISUAL STANDARD.
3. RECORDING DEVICE: THE RECORDING NEEDLE IS CONNECTED WITH THE VISUAL STANDARD THROUGH COMPONENTS SUCH AS AXLE WHEEL, AND THE DIRECTION AND ANGLE OF THE VISUAL STANDARD ARE RECORDED ON THE VISUAL FIELD DRAWING CORRESPONDINGLY.
4. SEAT FRAME: USED TO SUPPORT SEMI-CIRCULAR ARC BOW AND FIXED RECORDING DEVICE.
5. TEST THE HEAD MOLD: A STANDARD HEAD MOLD, THE TWO EYE HOLES OF THE HEAD MOLD ARE EQUIPPED WITH SMALL LIGHT BULBS, THE POSITION OF THE BULB AND THE POSITION OF THE HEAD MOLD ARE ACCORDING TO THE REQUIREMENTS OF GB 2890. THE TEST HEAD DIE MUST BE INSTALLED ON THE WORKBENCH IN SUCH A WAY THAT THE LEFT AND RIGHT EYES ARE PLACED AT THE CENTER OF THE SEMICIRCULAR ARCH AND THE "0" POINT IS DIRECTLY SEEN.

MAIN INDICATORS
1. SEMI-CIRCULAR ARC RADIUS: 335mm.
2. LEFT AND RIGHT FIELD OF VIEW: ≤120°.
3. BULB DISTANCE: THE VERTEX OF THE BULB IS CONNECTED AFTER THE TWO EYE POINTS (7±0.5).
APPLICABLE STANDARDS: GB/T 32610-2016, GB 2626-2019, GB2890-2009

Learn More

REFERENCE NUMBER: L-1502
MODEL: UE2410
QUANTITY: 1

Learn More