Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters
Sidel 2-step pet stretch-blow molders require previously manufactured preforms be supplied to the machine
Separating the bottle manufacturing and preform manufacturing processes allows production to be optimized, provides greater flexibility of operation and use, and provides higher production output rates and yield
Condition
Machine is in very good conditioning and well maintained
Maximum Preform Dimensions
Neck height: 9 – 41 mm (measured from bottom of support ring)
Minimum inside diameter of neck: 19 mm
Maximum outside diameter of neck: 34 mm
Preform support ring diameter: 29 – 51 mm
Maximum preform length: 210 mm
Maximum Bottle Dimensions
Maximum bottle diameter: 130 mm
Maximum bottle height: 380 mm
Bottle capacity: 0.25 – 3 liters
Average Preform Weights (Non Carbonated and Carbonated Liquids)
0.25 liter bottle: 14-20 grams
0.50 liter bottle: 20-33 grams
1.00 liter bottle: 26-40 grams
1.50 liter bottle: 35-51 grams
2.00 liter bottle: 44-58 grams
3.00 liter bottle: 68-84 grams
Blow Wheel
Height: 3.5 meters
Number of molds: 6
Closing force: 10 tons
Item height (under neck) at outfeed: 1.4 meters approximately
Machine DC drive motor power: 4 kW
Heat Conditioning
Height: 2 meters
Number of oven heating units: 10
Number of heating zones per unit: 8
Maximum power: 170 kW
Electrical Usage
Maximum supplied power: 200 kW
Average consumption: 100-150 kW/hr (varies per bottle being produced)
Compressed Air
Supplied power from 7-35 bar
Pressure: 7 bar
Flow rate: 50-100 Nm3/hr (varies per bottle being produced)
Blow pressure – champagne base: up to 25 bar
Blow flow rate – champagne base: 110-550 Nm3/hr
Blow pressure – petaloid base: up to 35 bar
Blow flow rate – petaloid base: 155-770 Nm3/hr
Chilled Water
Temperature: 10-12 degrees centigrade
Pressure: 5-6 bar
Flow rate: up to 6 cubic meters per hour
Kcal to be removed: up to 16,000 kcal per hour
Weight
Blow wheel with molds: 8 tons
Heat conditioning unit: 2.2 tons
Preform feeder: 0.65 tons
Electrical cabinet: 0.85 tons
Preform Heat Conditioning
The preforms are transferred neck up to the heat conditioning device
This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again
During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck
Heating is insured by 10 heat modules
Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled
The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile
These zones are regulated on all SBO models
After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature
Specifications
Weight: 11700
Request a Quote
✓
Request sent
Thank you, our team will reply to you shortly.
Direct access to our team
Email American Plant & Equipment
Tell us what you want to buy, source, finance, or sell. A machinery specialist will follow up with you.
✓
Thank you. Your request is with the American Plant and Equipment team.
A machinery specialist will follow up with you.
Machinery updates
Subscribe to our email list
Tell us which industries you follow and we will send you the machines that match.
✓
You are on the list.
We will email you when machines that match your interests come in. Unsubscribe from any message.
