Search results for: 'slitter machi'

TT-3204 SINGLE SHAFT AUTO CUTTING MACHINE, WORKING WIDTH 1500mm (BALONEY SLITTER, SUITABLE FOR FILMS) SLITTER REWINDER MAX SLITTING WIDTH: 1600mm (CAN BE CUSTOMIZED FROM 800mm TO 3000mm) MINI SLITTING WIDTH: 10mm UNWINDING DIAMETER: 600mm REWINDING DIAMETER: 300mm AUTOMATIC CUTTING MACHINE FOR FILM ROLLS: AFTER YOU SET THE PARAMETER IT WOULD CUT THE FILM ROLLS TO SMALL WIDTH ROLLS AUTOMATICALY WORKING WIDTH: 1500mm LARGE ROLL MATERIAL DIAMETER MAX: 350mm NO PROBLEM FOR THIS MACHINE TO SLIT YOUR PVC FILM MATERIAL Learn More

TT-5546 TRIM ASSOCIATED MACHINE DESIGN, 120”, REBUILT LANGSTON 304 SPEEDMASTER TWO DRUM SLITTER REWINDER 4000 FPM, YEAR 2002 USED TWO DRUM SLITTER REWINDER 138” WIDE LANGSTON 304 SPEEDMASTER REBUILT BY ASSOCIATED MACHINE DESIGN. HEAVY DUTY DESIGN CONDITION: USED QUANTITY: 1 Learn More

REFERENCE NUMBER: M-4081

JUDELSHON BIAS MACHINE AND SLITTER

 

THERE ARE SIX (6) PIECES TO THIS UNIT:

MODEL 220D (OFF ROLLER/FOLDER)

MODEL 220S (SEWING MACHINE WITH REROLLER FOR TUBULAR GOOD)

MODEL 220B - TWO PIECES (SPINNING UNROLLER AND CUTTER/REROLLER)

MODEL 360 SLITTER (71" LONG SHAFT)

MODEL 420 REROLLER

BIAS MACHINE CAN ACCEPT ROLLS UP TO 84" WIDE

THE SLITTER HAS A 15" BLADE

Learn More

TT-7376 TOWERS MACHINERY MODEL 440 REWIND SLITTER 1. TOWERS MACHINERY MODEL 440 REWIND SLITTER 2. CRUSH TYPE 3. REWIND SLITTER QUANTITY: 1 Learn More

YY-3389 SLITTER REWINDER MACHINE FOR TOILET AND TISSUE PAPER, PRODUCTION SPEED 80 TO 180 M PER MIN AUTOMATIC TOILET PAPER AND TISSUE PAPER TRIMMING AND SEALING REWINDING MACHINE INCLUDES ADVANCED PLC CONTROL SYSTEM, FREQUENCY CONVERSION SPEED CONTROL, ELECTRONIC BRAKE WITH MULTI-PICTURE HUMAN-MACHINE INTERFACE TOUCH SCREEN OPERATING SYSTEM, SPECIALIZING IN THE PRODUCTION OF FLAT ROLLS OF TOILET PAPER CORE AND CORELESS ROUND ROLLS, THE EQUIPMENT HAS AN AUTOMATIC REWINDING, PAPER ROLLS FORMED WITH AUTOMATIC DELIVERY, AUTOMATIC CORE SHAFT, AUTOMATIC CORE SHAFT PULLING, AUTOMATIC CYCLING OF THE CORE SHAFTS, AUTOMATIC SEALING AND GLUING OF THE END, AUTOMATIC COMPRESSION, AUTOMATIC TRANSPORT TO THE CUTTING SYSTEM. THE MACHINE CAN BE AUTOMATICALLY TRANSPORTED TO THE CUTTING SECTION, WHICH ALLOWS FOR UNMANNED REWINDING, IMPROVES THE WORKING EFFICIENCY, REDUCES LABOR. QUANTITY: 1 Learn More

TT-3984 BALONEY SLITTER FABRIC AUTOMATIC CUTTING MACHINE – NEW, WIDTH 2500mm, 400mm DIAMETER (94.4 INCHES WIDE X 15.7 INCHES DIAMETER) NEW 2500mm FABRIC AUTOMATIC CUTTING MACHINE FOR WOVEN FABRICS, TENTS, UMBRELLAS, LEATHER, REFLECTIVE MATERIAL, PLASTIC, PAPER, DOUBLE SIDED TAPE, ACETATE CLOTH, REINFORCED BELT, CONDUCTIVE CLOTH, AND STRAIGHT, OR 45° OBLIQUE CUT FOR CLOTH FOR APPAREL, BAGS, SHOES, CLOTHING ACCESSORIES, REFLECTIVE MATERIAL FACTORY, TENT FACTORY, UMBRELLA FACTORY, ELECTRONICS FACTORY AND OTHER INDUSTRIES. Learn More

YY-1769 PONTOTOC MACHINE WORKS HORIZONTAL SLITTER (AUTOMATIC) QUANTITY: 1 Learn More

YY-2691 CROSS PERFORATION MACHINE WITH SLITTER - 1600mm (64 INCHES) ASK FOR MORE DETAILS! QUANTITY: 1 Learn More

TT-6290 TUBULAR KNIT SLITTER AND CIRCULAR SEWING MACHINE Learn More

REFERENCE NUMBER: M-1480

SLITTER REWINDER 1800mm WIDTH AND 1000mm DIAMETER-NEW MACHINE

 

TECHNICAL CHARACTERISTICS:

 

UNWINDER

MAXIMUM WIDTH: 1800mm

MAXIMUM DIAMETER: 1100mm

MINIMUM WIDTH: 420mm

MAXIMUM WEIGHT: 300kgs

CORE ID: 3”

 

REWINDER:

MAXIMUM WIDTH: 1800mm

MAXIMUM DIAMETER: 1000mm

MINIMUM WIDTH: 100mm

MAXIMUM WEIGHT PER SHAFT: 300kgs

CORE ID: 3”

 

MATERIAL:

TYPE: 100% PP NONWOVEN

MINIMUM: 10gsm

MAXIMUM: 150gsm

 

TENSION:

MAXIMUM: 2 PLI

 

SPEED:

METERS PER MINUTE: 250

 

DESCRIPTION:

REWINDER MACHINE FOR NONWOVEN ROLLS: UP TO 1000 mm DIAMETER AT UNWINDER AND 1200 mm AT REWINDER.

THE WORKSTATION OFFERS EASY ACCESS TO THE TENSION CONTROL AREA AS WELL AS THE TRIMMING AREA; THIS WAY, ANY MODIFICATION ON THE MATERIAL MEASUREMENTS CAN BE DONE SAFELY.

THE WORKSTATION WILL DELIVER MODULES OF ROLLED MATERIAL WITH SPECIFIC DENSITY, AND SEPARATED FROM EACH OTHER IN ORDER TO KEEP OPERATION CONDITIONS WITHIN REQUIRED QUALITY CONTROLS.

 

UNWINDER WITH SHAFT:

THERE IS A CENTRAL UNWINDING SYSTEM SUPPORTED BY A 3” STEEL EXPANSION SHAFT.

THERE IS A TENSION CONTROL SYSTEM THAT WORKS THROUGH A PNEUMATIC DISK BRAKE WITH A REPLACEABLE PADS SYSTEM.

THE UNWINDER HAS A PIVOTABLE ROLLER SYSTEM WHEREBY TENSION MAY BE MODIFIED ON ONE END TO REDUCE TENSION DIFFERENCE ON MATERIAL IF NECESSARY.

THE SAFETY CHUCK HAS A MECHANICAL MOVEMENT SYSTEM FOR SHAFT INSERTION.

THE UNWINDER HAS AN ULTRASONIC OR LASER SENSOR FOR A REAL MEASURING OF ROLL DIAMETER. THIS INFORMATION WILL HELP TO KEEP A SPECIFIC TENSION ON MATERIAL DURING ALL THE PROCESS.

 

CUTTING:

THE LONGITUDINAL SHEAR CUT SYSTEM GUARANTEES CLEAN AND SAFE TRIMMING AT EVERY MODULE. THE CUTTING SYSTEM ADAPTED TO THE MAIN TRANSMISSION GUARANTEES AN OVER SPEED THAT MAY BE REGULATED ACCORDING TO THE MATERIAL DURING EVERY STAGE OF PROCESS. THE PNEUMATIC ACTIVATION KNIVES WILL ALLOW A FAST MODIFICATION OF THE CUTTING MEASUREMENTS.

THIS ROLLER IS LOCATED AT AN EASY ACCESS AREA FOR THE OPERATOR TO BE ABLE TO MAKE CHANGES ON THE CUTTING WIDTH SAFELY. THE COUNTER KNIVES ARE ASSEMBLED TO THE ROLLER BY 3 SETSCREWS THAT FIX THEIR POSITION ON THE ROLLER. THE COUNTERKNIVES HAVE TWO FACES, SO WHEN THE FIRST FACE HAS AN IMPORTANT WEAR, IT WILL BE REMOVED FROM THE ROLLER AND THE NEW FACE WILL BE PLACED INSTEAD. THIS WILL EXTEND THE LIFESPAN OF THIS IMPORTANT COMPONENT.

SHEAR CUT KNIVES: THERE IS AN ADJUSTMENT MECHANISM TO PLACE THEM ON THE COUNTER KNIFE AND TO ADJUST THE CUTTING LOAD ACCURATELY. THE COUNTER KNIVES ARE SUPPORTED TOWARDS THE ROLLER IN ORDER TO OBTAIN A CUTOFF. THE SPEED ON THIS SYSTEM IS AN OVER SPEED IN RELATION TO THAT OF THE MATERIAL, IN ORDER TO GENERATE A CLEAN CUT.

LONGITUDINAL SHEAR CUT: PNEUMATIC ACTIVATION.

COUNTER KNIVES ROLLER WITH 3 SUPPORT PLANES FOR THE COUNTER KNIVES; 120° DISPLACEMENT FROM EACH OTHER.

19 SLITTERS ARE INCLUDED.

 

REWINDER:

PERIPHERAL REWINDER FOR NONWOVEN. THIS SYSTEM HAS A COUPLE OF MAIN ROLLERS WHERE THE MATERIAL ROLL IS FORMED.

THIS SYSTEM HAS LINEAR GUIDES FOR COMPACTION THROUGH WICH A NIP IS OBTAINED ON THE MATERIAL. THE REWINDER WILL HAVE A TRANSMISSION BASED ON A VECTORIAL-TYPE MOTOR ADAPTED TO A CYCLOIDAL REDUCER. THE TRANSMISSION HAS A MECHANICAL TORQUE CONTROL SYSTEM TO CONTROL THE TORQUE DIFFERENTIAL BETWEEN MAIN ROLLS.

THIS SYSTEM WILL HAVE A 3” EXPANSION SHAFT WHERE THE CARDBOARD CORES WILL BE INSERTED AND THE MATERIAL ROLLS WILL BE FORMED.

 

FABRIC OPENING SYSTEM:

THIS SYSTEM IS BASED ON A VARIABLE CURVATURE SYSTEM BY A CENTER KNOB AND IT IS A BAR- TYPE SYSTEM. THIS KNOB IS THERE TO CONTROL THE CURVATURE OF THE BAR WHERE MATERIAL SLIDES THROUGH. THE SLIDING BAR IS MADE OUT OF AN ULTRA LOW FRICTION MATERIAL IN ORDER TO GENERATE A SMOOTH SLIDING OF MATERIAL WITHOUT ANY TENSION ADDED. THIS WILL REDUCE WRINKLES IN A SIGNIFICANT WAY.

 

AUTOMATIC TENSION SYSTEM:

THERE IS AN OPEN LOOP AUTOMATIC TENSION CONTROL SYSTEM WITH A SENSOR FOR DIAMETER MEASURING. BY THIS SYSTEM, A REAL VALUE OF DIAMETER IS OBTAINED AT THE REWINDER. PRESSURE OF PNEUMATIC BRAKE VARIES DURING PROCESS.

 

MANUAL POSITIONING (OPTIONAL):

THE MANUAL POSITIONING SYSTEM IS BASED ON THE POSITION CONTROL OF THE COUNTER KNIVES. THE MODULE IS POSITIONED AT A DESIRED CUTTING PARAMETER AND THE COUNTER KNIFE WILL PHYSICALLY COME ACROSS IT. THE REAL POSITION OF MODULE WILL BE SHOWN ON A SCREEN THAT OPERATOR WILL BE CONSTANTLY SUPERVISING. THIS SCREEN WILL SHOW THE REAL MEASUREMENTS OF THE CARRIAGE IN RELATION TO THE LAST ONE OR AS AN ABSOLUTE REFERENCE. OPERATOR WILL BE ABLE TO RESET THE MEASUREMENT ONCE THE COUNTER KNIFE IS REPLACED AND WILL REPEAT THIS PROCESS EVERY TIME A COUNTER KNIFE IS POSITIONED.

A DISPLAY WILL SHOW THE DESIRED POSITION IN MILLIMETERS OR INCHES.

THIS SYSTEM CAN SHOW MEASUREMENT IN AN EITHER ABSOLUTE OR INCREASING WAY.

POSITION TOLERANCE: +/- 0.30 mm.

THE POSITIONER IS INSTALLED ON A SUPPORT THAT WILL BE LOCATED ON THE REWINDER BENCHES. THEREFORE, THERE WILL BE AN EASY ACCESS TO SYSTEM AND AN EASY REPETITION OF POSITIONING PROCESS.

 

UNLOADING ROLL TABLE:

A HYDRAULIC PIVOTEABLE TABLE WILL HAVE AS MAIN FUNCTION THE UNLOADING OF FINISHED ROLLS THAT THEN WILL BE LOCATED ON FLOOR LEVEL. THIS SYSTEM WILL EJECT THE ROLL AND THEN IT WILL BE RECEIVED AT THE PIVOTING TABLE FOR AN EFFICIENT UNLOADING.

THE UNLOADING TABLE WILL ALSO WORK AS A PROTECTION FOR THE OPERATOR.

THIS EQUIPMENT WILL HAVE SECURITY CURTAINS AT FRONT TO KEEP OPERATOR FROM ENTERING THE REWINDING AREA. THERE WILL BE AN EMERGENCY STOP BUTTON OR WIRE WHERE OPERATOR WORKS AND WILL ALSO HAVE PHYSICAL PROTECTION WITH SECURITY SWITCHES AT CUTTING AREA.

 

CONTROL:

HMI CENTRAL CONTROL SYSTEM WITH TOUCH SCREEN TO PROGRAM THE OPERATION CYCLE AND ALL THE MATERIAL CHARACTERISTICS. OPERATOR WILL HAVE ACCESS TO ALL OPERATION PARAMETERS IN ORDER TO BE ABLE TO MAKE CHANGES ON THE EQUIPMENT OPERATION CONDITIONS, AND THEREFORE OBTAIN MATERIAL ROLLS WITH SPECIFIC DENSITIES.

TRANSMISSION: VECTORIAL MOTO REDUCER WITH 1000:1 TORQUE.

DIGITAL METER COUNTER WITH DISPLAY AND AUTOMATIC STOP AT DEFINED DISTANCE.

 

DOCUMENTS INCLUDED:

THE MACHINE WILL BE DELIVERED WITH THE FOLLOWING DOCUMENT:

OPERATION MANUAL

MAINTENANCE MANUAL

SAFETY MANUAL

ELECTRIC DIAGRAMS

CONTROL SYSTEM MANUAL

PLC BACKUP

REQUIREMENTS:

ELECTRIC 15 KW, 440 VAC, TRI PHASE.

PNEUMATIC 6 BAR - 60 LTS. / MIN.

 

DUCTS AND WIRING:

DUCTS AND WIRES RUNNING FROM UTILITIES SOURCES TO THE CONTROL PANEL AND FROM THE CONTROL PANEL TO THE MACHINE WILL BE AT CUSTOMER COSTS AND MUST BE DONE ACCORDING TO THE INSTRUCTIONS SHOWN IN OUR DIAGRAMS

 

SIEMENS PLC

Learn More