Search results for: 'Comp'

P-3555 ZIMMER MIDI II-F-R/7 SAMPLE TABLE FOR ROTARY AND FLAT PRINTING YEAR 1998 WIDTH 3200mm

ZIMMER
MODEL: MIDI II-F-R/7
SAMPLE TABLE FOR ROTARY AND FLAT PRINTING
YEAR: 1998 FULLY RECONDITIONED END 2012
WIDTH: 3200mm
1 HEAD
BELT 10m
TOTAL RATIO 20 m
COMPLETE WITH:
1 REGGIANI
DRYER AT STEAM
BELT WIDTH 3060mm
1 COMPARTMENT

QUANTITY: 1

Learn More

M-6262 RF SYSTEMS TD-85 RADIO FREQUENCY DRYER FOR CONES YEAR 2002

RADIO FREQUENCY DRYER FOR CONES
MAKE: RF SYSTEMS
MODEL: TD-85 (K85)
YEAR: 2002
THREE PHASES 380 – 50 HZ
FOR DIFFERENT VOLTAGE THE MACHINE IS EQUIPPED WITH AUTO TRANSFORMER
THE NOMINAL VOLTAGE SHOULD BE WITHIN 5% (TEMPORARY EXCURSIONS OF +5% AND -5% ARE PERMITTED) OTHERWISE CUSTOMER MUST INSTALL A SUITABLE STABILIZER
MAXIMUM POWER ABSORBED FROM THE MAINS: 130 KVA
MAXIMUM CURRENT ABSORBED: 210 A
GAUGE WIRE: 3x75mm2 + GROUND 50mm2 MINIMUM

GENERATOR
MAXIMUM POWER RADIO FREQUENCY GENERATOR: 85 KW (1 x 85KW)
WORK FREQUENCY: 27 MHZ
COOLING SYSTEM: FORCED AIR
MAXIMUM ROOM TEMPERATURE: TA = 35°C IF HIGHER POWER MUST BE REDUCED
MAXIMUM EXHAUST AIR TEMPERATURE: TU = 85°C
OSCILLATOR: CAVITY TYPE WITH HIGH OVERALL EFFICIENCY
FREQUENCY STABILITY: WITHIN LIMITS
RADIATED FIELD: WITHIN LIMITS
GRID CURRENT WITH NO LOAD: 2.3 A TO 2.5 A
GRID CURRENT MINIMUM WITH FULL LOAD: 1.4 A
TRIODE TYPE: RS 3060 CL
FILAMENT TRIODE VOLTAGE: 10 V + 1% - 3%

BELT – CONVEYOR
MATERIAL: POLYESTER FABRIC
TRACKING: AUTOMATIC
LENGTH: 21600mm
WIDTH: 1750mm
RANGE OF CONVEYOR SPEED: 0 TO 50 M/ORA
ELECTRODE: STANDARD TYPE

PRODUCTIVITY
MAXIMUM EVAPORATING CAPACITY: 90 KG WATER PER HOUR

DIMENSIONS
LENGTH: 9600mm
WIDTH: 2124mm
MAXIMUM HEIGHT: 3400mm
GALLERY LENGTH: 4000mm
INLET LENGTH: 2800mm
OUTLET LENGTH: 2800mm
BELT WIDTH: 1750mm
LOAD HEIGHT: 900mm
MAXIMUM HEIGHT OF INLET TRAP: 300mm

THE DRYER TD85 IS COMPOSED OF ONE UNITY OF 85 KW

SPECIAL REQUIREMENTS ON USING RADIO FREQUENCY DRYER
THE DRYER CAN ACCEPT ONLY HYDROEXTRACT GOODS WITH EVEN MOISTURE CONTENT
POSSIBLE FIRE HAZARD WHEN DEALING WITH UNEXTRACTED PACKAGES
PROPEN HYDROEXTRACTION IS IMPORTANT PRIOR TO RF DRYER
LOAD PRODUCT WITH SAME DIMENSIONS AND SIMILAR MOISTURE CONTENTS
PACKAGE PLACEMENT ON THE BELT. ANY TYPE OF TUBE MAY BE USED IN A CONTINUED RF DRYER
METAL TUBES REQUIRE MOVE CARE IN PLACEMENT ON THE BELT THEN PLASTIC TUBE
METAL TUBES CAN CAUSE SHORT CIRCUITY, OR ARCING, FROM ONE ELECTRODE TO GROUND, WHICH CAN DAMAGE THE BELT OR CAUSE FIRE
PACKAGE WITH METAL TUBES MUST BE PLACED ON THE BELT SO THE METAL IS PARALLEL TO THE ELECTRODES AS SHONS IS TY
THE CONVEYOR SHOULD ALWAYS BE LOADED EVENLY, WITH NO BIG EMPTY GAPS
LOAD AS MUCH AS YOU CAN
GOOD WITH DIFFERENTS SIZE ARE NOT ALLOWED THEY CAN GET BURNS
LOAD A QUANTITY OF GOODS WITH A QUANTITY OF WATER TO REMOVE PER LINEAR METER OF BELT AROUND 5 TO 15 KG PER LINEAR METER OF BELT
THE MACHINE CANNOT ACCEPT METALLIC DYSTUFF (EX.CHROME)
DO NOT ENTER METALLIC PARTS
METALLIC IN THE GALLERY CAUSES ELECTRICAL DISCHARGES WHICH MAY THOROUGHLY RUIN BELT AND SET THE DRYING MATERIAL ON FIRE

QUANTITY: 1

Learn More

P-4879 KRANTZ STENTER YEAR 1989 WIDTH 2200mm 5 CHAMBERS

KRANTZ
STENTER
YEAR: 1989 (COMPLETELY REFURBISHED 2006)
WORKING WIDTH: 2200mm
ENTRY FROM TROLLEY OR A-FRAME
BIANCO INFEED UNIT, YEAR 2006

QUANTITY: 1

Learn More

REFERENCE NUMBER: P-2795

GEMATEX MAYER POLAR FLEECE LINE RAISING MACHINE YEAR 1999 WIDTH 2200mm

 

COMPLETE LINE FOR PRODUCTION OF FLEECE

GEMATEX MAYER

MODEL: POLAR FLEECE LINE

OPTISYSTEM NAPPER KRM 6725

YEAR: 1999

WIDTH: 2200mm

24 ROLLERS ON THE TAMBOUR

MACHINE IN PERFECT WORKING CONDITION

 

GEMATEX

YEAR: 1993

ROLLER WIDTH: 2100mm

 

MAYER & CIE

TYPE: MLPX II

KNITTING MACHINE

YEAR: 1991

UIGLENIA NUMBER NU 20 26 INCHES

NUMBER OF FEEDERS: 42 CONI

CENTRAL LUBRICATION SYSTEM SENSO

MACHINE IS CURRENTLY SET WEIGHT MICROFLEECE 210 GR/M2

 

MAYER & CIE

TYPE: MLPX II

KNITTING MACHINE

YEAR: 1993

UIGLENIA NUMBER NU 20 30 INCHES

NUMBER OF FEEDERS: 48 CONI

LUBRICATION SYSTEM SENSO CENTRAL

MACHINE IS CURRENTLY SET TO FLEECE WEIGHT OF 280 GR / M2

 

MAYER & CIE

TYPE: MLPX 1.6

KNITTING MACHINE

YEAR: 1998

UIGLENIA NUMBER NU 24 30 INCHES

NUMBER OF FEEDERS 48 CONI

CENTRAL LUBRICATION SYSTEM SENSO

MACHINE IS CURRENTLY SET FOR FLEECE WEIGHT OF 200 GR / M2

 

MAYER & CIE

TYPE: MLPX

KINTTING MACHINE

YEAR: 1999

UIGLENIA NUMBER NU 30 INCHES

NUMBER OF FEEDERS: 48

CENTRAL LUBRICATION SYSTEM SENSO

MACHINE IS CURRENTLY SET TO FLEECE WEIGHT OF 250 GR / M2

 

QUANTITY: 6

Learn More

REFERENCE NUMBER: M-4327

BENNINGER ZELL SIZING MACHINE MODEL BEN-SIZETEC WORKING WIDTH 2200mm YEAR 1994

 

BENNINGER ZELL SIZING MACHINE  MODEL BEN - SIZETEC WORKING WIDTH 2200 mm

YEAR  1994, WITH SECTIONAL AND FRACTIONAL SYSTEM.

N° A13715

MODEL  BB-S/ZT4/4/TKD

1 SECTIONAL BEAM UNROLLING DEVICE MODEL SWA WITH LOADING CELL FOR MEASURING

THE OUT GOING TENSION .

ELECTRO PNEUMATIC BREAKING SYSTEM

MAXIMUM BEAM DIAMETER 1000 mm.

1 FRACTIONAL BEAMING UNROLLING DEVICE WITH CAPACITY UP TO 20 POSITIONS

ELECTRO PNEUMATIC BREAKING SYSTEM

1 SIZING BOX MODEL TDK WORKING WIDTH 2200 mm. TOTAL WIDTH 2400 mm

STAINLESS STEEL BOX WITH TOTAL CAPACITY OF 240 LITERS WITH DIRECT STEAM INJECTION

LOWER VESSELS WITH INDIRECT HEAT SYSTEM

AUTOMATIC SIZE BOX FEEDING

HANDYMAT FOR START AND STOP AND MACHINE REGULATION

1 DRYING SECTION DEVICE MODEL ZT8 – WORKING WIDTH 2200 mm

6 DRYING STAINLESS STEEL CYLINDERS COVERED WITH TEFLON + 2 CYLINDERS WITHOUT TEFLON

4 ELECTRONIC TEMPERATURE REGULATIONS

2 AIR EXTRACTION

1 OIL/GREASE APPLICATION DEVICE MODEL CV

1 YARN SPLITTING DEVICE

7 RODS FOR SECTIONAL BEAMS

19 RODS FOR FRACTIONAL BEAMS

1 HUMIDITY MAHLO CONTROL DEVICE MODEL RMS-7S N°1670/1/10597

1 BEAM ROLLING DEVICE MODEL BB FOR BEAMS UP TO 1000 mm DIAMETER

YARN TRACTION MADE UP OF 3 ROLLS

1 PRESSURIZED ROLLER DEVICE

TENSION AND PRESSURE MEASURE DEVICES

AUTOMATIC BEAM LIFT DEVICE INCLUSIVE OF ADAPTORS FOR DIFFERENT BEAMS

EXTENSION REED FOR ENDS WIDTH CONTROL

MIRROR FOR EASY YARN CONTROL

1 HANDYMAT FOR START AND STOP AND MACHINE REGULATION

1 DUST SUCTION DEVICE

1 COMPLETE SIZE KITCHEN PREPARATION INCLUDING 2 TANKS FOR SIZE STORAGE

1 FULLY AUTOMATIC BENSIZETEC PROCESS CONTROL DEVICE INCLUDING HARDWARE AND SOFTWARE

1 EXTERNAL ELECTRIC CABINET.

Learn More

REFERENCE NUMBER:   G-8230

HIGH-TEMPERETURE AND HIGH-PRESSURE YARN DYEING MACHINE 40KG

 

DESIGNED FOR DYEING, BOILING OFF, BLEACHING, AND WATER WASHING, ETC. SUITABLE FOR HANK YARN, BOBBIN OR RAW STOCK FIBER

 

MACHINE TYPE: VERTICAL CYLINDER

VAT DIAMETER: Ф600mm

CONE QUANTITY: 7 X 7 = 49 CONES

WORKING TEMPERATURE: 130C

MAX WORKING PRESSURE: 0.4MPA

BOTH RATIO: 1:7 TO 9

WITH COMPUTERIZED CONTROL SYSTEM

HEAT EXCHANGING: COIL TYPE HEAT EXCHANGER, WHICH CAN BE USED FOR EITHER HEATING OR COOLING.

HEAT EXCHANGING SPEED: WHEN THE HEATED STEAM PRESSURE IS 0.4MPA, 40MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BARREL RAISING FROM 20^OC TO 130^OC. WHEN THE COOLING WATER PRESSURE IS 0. 3MPA AND THE WATER TEMPERATURE IS 20 ^OC, 40 MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BECK TO LOWER FROM 130^OC TO 80^OC.

RECYCLING OF DYEING LIQUID: THE POSITIVE AND NEGATIVE RECYCLING OF DYEING LIQUID WILL BE ADJUSTED BY THE CYLINDER THROUGH THE SWITCHING DEVICE INSIDE THE CENTRIFUGAL PUMP.

SEALING OF BOILER: RUBBER ADHESIVE

THE WORKING PRESSURE INSIDE THE TANK WILL MAKE THE RUBBER SEAL CLOSELY TO ATTACH THE FLANGE. THE CONICAL SURFACE OF THE TANK MOUTH IS TO ENHANCE THE SEALING.

OPENING OF TANK COVER: FIRST OPEN THE AIR VALVE TO RELEASE THE PRESSURE INSIDE THE BOILER. WAIT UNTIL NO EXHAUSTED AIR GOING THRU THE EXHAUST VALVE AND THE READING OF PRESSURE GAUGE IS ZERO, WITHDRAW THE WRENCH HANDLE, OPEN THE CLAMPING HOOP TO REMOVE THE FLANGE; AND THEN OPEN THE COVER WITH DRAG WEIGHT. THE COVER WILL BE CLOSED.

 

CONFIGURATION:

1. ELECTRICAL CABINET: STAINLESS STEEL CABINET, PLASTIC COATING

2. ELECTRICAL COMPONENTS: SIEMENS, OMRON

3. COMPUTER: HG COMPUTER (MADE IN CHINA)

4. ELECTROMAGNETIC VALVE: TAIWAN YADEKE

5. PUMP: CENTRIFUGAL PUMP

6. MOTOR: WANNAN MOTOR

7. TEMPERATURE CONTROL: COMPUTER CONTROL, WITH HEATING, COOLING, KEEPING WARM, ETC. FUNCTION.

8. HEAT EXCHANGER: INTERNAL COIL HEATING

9. VALVE: STAINLESS ANGLE VALVES, PNEUMATIC BUTTERFLY VALVES

10. ONE CARRIER BASKET

11. MACHINE BODY MATERIAL: STAINLESS STEEL, 316 LITERS

12. ACCESSORIES: SEAL RING FOR DYE VAT, SEAL FOR MAIN PUMP, SEAL FOR REVERSING SHAFT

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: K-5601

KUSTERS CONTINOUS BLEACHING RANGE YEAR 2004 3400MM

 

YOM: 2004

WIDTH: 3400mm

FACE WIDTH

WORKING WIDTH 3200mm

PRODUCTION SPEED 70 METER/MIN

TECHNICAL SPEED 100 METER/MIN

WATER PRESSURE 2.0-2.5 BAR

STEAM 2.0-2.5 BAR

REQUILTERED COMPRESSED AIR 7.0 BAR

FABRIC WEIGHT 70-250 GSM

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: C-3851

MONFORTS STENTER FOR KNITS

MODEL: MONTEX 6500 7F TWINAIR

7 CHAMBERS GAS HEATED

WORKING WIDTH: 2200mm

YEAR: 2012

 QUANTITY: 1

Learn More

REFERENCE NUMBER: C-3845

NOVOPAC WRAPPING MACHINE FOR TUBULAR

YEAR: 1990

QUANTITY: 1

Learn More

REFERENCE NUMBER: C-2319 LAMPERTI TRICOMBINED BRUSH TIGERING, LUSTRING AND SHEARING LINE LC/SF, WIDTH 2600mm TO 2680mm, YEAR 1980 DETAILS: MADE: LAMPERTI TYPE: LC/SF YEAR: 1980 ROLLER WIDTH: 2600mm QUANTITY AVAILABLE: 1 Learn More