Search results for: 'steam+electr'

TT-6339 COMPLETE PLANT FOR MODERN DENIM DYEING & FINISHING, YEAR 2004 Learn More

REFERENCE NUMBER: P-1813 BRAZZOLI H.T. SATURNO LUFT HTF DYEING MACHINE YEAR 2002 400KG BRAZZOLI MODEL: H.T. DYEING MACHINE TYPE: SATURNO LUFT HTF FOR TERRY TOWEL FABRICS YEAR: 2002 CAPACITY: 400 KILOGRAMS EACH MACHINE TEHSE MACHINES CAN ALSO BE OPERATED COUPLED TO DYE ONE LOT OF 800 KILOGRAMS SUPPLIED WITH MAIN MOTOR AND PUMP AUTOMATIC VALVES FOR STEAM AND WATER FUNCTIONS ADD TANK + DOSING PUMP ELECTRICAL PANEL WITH MICROPROCESSOR CONTROLS TEST RUN POSSIBLE, SINCE THE UNITS ARE STILL FULLY CONNECTED TO THE ELECTRICITY, STEAM, WATER, ETC QUANTITY AVAILABLE: 2 Learn More

REFERENCE NUMBER: A-1227 (0101GHBXX12) A POONG KWANG SANFORIZER (SHRINKING RANGE) MODEL PK-S1-1800 MAKER: POONG KWANG YEAR: 2002 (RECONDITIONED IN 2013) MODEL: PK-S1-1800 WORKING WIDTH: 1800 MM QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4701 (1111DPTVXX10) L RAMISCH RK 360-H CALENDER YEAR 1971 WIDTH 2200mm (RENEWED IN 2008) RAMISCH CALENDER TYPE RK 360 – H (FOR CALENDERING AND COTTON LUSTERING) WORKING WIDTH 2200mm 3 ROLLERS TOTAL WIDTH 2400mm (STEEL/COTTON/STEEL) YEAR 1971 BUT TOTALLY RENEWED IN YEAR 2008 MAXIMUM PRESSURE 160 BARS ON BOTH LATERAL HYDRAULIC CYLINDERS (LEFT AND RIGHT) INVERTER HITACHI SJ 300 TEMPERATURE CONTROL APAR AR650, AR682 METER COUNTER SIMEX SLK-94 METAL DETECTOR CEIA SEAM DETECTION CACCIA ELECTRNICA WITH DOUBLE CONTROLLER STEAM PRESSURE 4 BARS STEAM CONSUMPTION CA 400 KG/H MOTOR POWER: 30 KW QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: K-9326 BABCOCK WIDE TENTER FRAME 144" (3657mm) QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER:   G-8230

HIGH-TEMPERETURE AND HIGH-PRESSURE YARN DYEING MACHINE 40KG

 

DESIGNED FOR DYEING, BOILING OFF, BLEACHING, AND WATER WASHING, ETC. SUITABLE FOR HANK YARN, BOBBIN OR RAW STOCK FIBER

 

MACHINE TYPE: VERTICAL CYLINDER

VAT DIAMETER: Ф600mm

CONE QUANTITY: 7 X 7 = 49 CONES

WORKING TEMPERATURE: 130C

MAX WORKING PRESSURE: 0.4MPA

BOTH RATIO: 1:7 TO 9

WITH COMPUTERIZED CONTROL SYSTEM

HEAT EXCHANGING: COIL TYPE HEAT EXCHANGER, WHICH CAN BE USED FOR EITHER HEATING OR COOLING.

HEAT EXCHANGING SPEED: WHEN THE HEATED STEAM PRESSURE IS 0.4MPA, 40MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BARREL RAISING FROM 20^OC TO 130^OC. WHEN THE COOLING WATER PRESSURE IS 0. 3MPA AND THE WATER TEMPERATURE IS 20 ^OC, 40 MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BECK TO LOWER FROM 130^OC TO 80^OC.

RECYCLING OF DYEING LIQUID: THE POSITIVE AND NEGATIVE RECYCLING OF DYEING LIQUID WILL BE ADJUSTED BY THE CYLINDER THROUGH THE SWITCHING DEVICE INSIDE THE CENTRIFUGAL PUMP.

SEALING OF BOILER: RUBBER ADHESIVE

THE WORKING PRESSURE INSIDE THE TANK WILL MAKE THE RUBBER SEAL CLOSELY TO ATTACH THE FLANGE. THE CONICAL SURFACE OF THE TANK MOUTH IS TO ENHANCE THE SEALING.

OPENING OF TANK COVER: FIRST OPEN THE AIR VALVE TO RELEASE THE PRESSURE INSIDE THE BOILER. WAIT UNTIL NO EXHAUSTED AIR GOING THRU THE EXHAUST VALVE AND THE READING OF PRESSURE GAUGE IS ZERO, WITHDRAW THE WRENCH HANDLE, OPEN THE CLAMPING HOOP TO REMOVE THE FLANGE; AND THEN OPEN THE COVER WITH DRAG WEIGHT. THE COVER WILL BE CLOSED.

 

CONFIGURATION:

1. ELECTRICAL CABINET: STAINLESS STEEL CABINET, PLASTIC COATING

2. ELECTRICAL COMPONENTS: SIEMENS, OMRON

3. COMPUTER: HG COMPUTER (MADE IN CHINA)

4. ELECTROMAGNETIC VALVE: TAIWAN YADEKE

5. PUMP: CENTRIFUGAL PUMP

6. MOTOR: WANNAN MOTOR

7. TEMPERATURE CONTROL: COMPUTER CONTROL, WITH HEATING, COOLING, KEEPING WARM, ETC. FUNCTION.

8. HEAT EXCHANGER: INTERNAL COIL HEATING

9. VALVE: STAINLESS ANGLE VALVES, PNEUMATIC BUTTERFLY VALVES

10. ONE CARRIER BASKET

11. MACHINE BODY MATERIAL: STAINLESS STEEL, 316 LITERS

12. ACCESSORIES: SEAL RING FOR DYE VAT, SEAL FOR MAIN PUMP, SEAL FOR REVERSING SHAFT

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: J-2640
DYEING AND FINISHING PLANT FOR SALE

ITEM 001
THIES SAMPLE DYEING MACHINE
MODEL: MINISOFT SAMPLE
CAPACITY: 50 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 002
THIES DYEING MACHINE
MODEL ECOSOFT PLUS
3 PORT SPLIT/SPLIT
CAPACITY: 900 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 003
THIES DYEING MACHINE
MODEL: ECOSOFT PLUS
2 PORT SPLIT/SPLIT
CAPACITY: 600 KGS
YEAR: 1999
MICROPROCESSOR CONTROL
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 004
THIES DYEING MACHINE
MODEL ECOSOFT PLUS
1 PORT SPLIT/SPLIT
CAPACITY: 300 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: A460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 005
GASTON COUNTY DYEING MACHINE
MODEL: AQUAFLOW
2 PORT
CAPACITY; 250 KGS
YEAR: 1987
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING AND UNLOADING REEL
QUANTITY: 1

ITEM 006
THIES DYEING MACHINE
MODEL: SOFT TRD
2 TUBE
CAPACITY: 700 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 007 (also our J-2647)
LAFER OPEN WIDTH COMPACTOR MACHINE
MODEL: KSA 500 2400/2200
YEAR: 1998
LAFER TEXEN CONTROLS
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION BAR ENTRY TO LATTICE ROLL GUIDER
• OPERATOR’S PLATFORM
• PUP TENTER WITH KNIT ENTRY, VERTICAL PIN CHAIN, WITH PLATE GUIDES, RAIL OPENING, PINNING BRUSHES, PINS ONLY, WITH SUPPORT SECTION FOR THE FABRIC IN THE CENTER, AT 10’ THERE IS A STEAMING SECTION, TOTAL LENGTH OF THE TENTER IS 30’, WITH AUTOMATIC LUBRICATION FOR THE CHAIN
• KSA 500 COMPACTOR BENCH WITH TEXEN CONTROLS
• TENSIONLESS FABRIC CONVEYOR
• PLAITOR AND FABRIC SCRAY WITH OPTICAL LOAD SENSOR
• INLINE INSPECTION BATCHER MACHINE, WITHH A BACK LIGHTED BOARD, MANUAL CUT
• SCALE TO WEIGHT THE FABRIC
QUANTITY: 1

ITEM 008 (also our J-2648)
SANTEX TUBULAR 4-ROLL EXTRACTION PAD
MODEL: SANTASTRETCH PLUS 140
YEAR: 1998
COMPOSED OF TURNTABLE, DETWISTER, TUBULAR 4-ROLL PAD WITH WET SPREADERS, PLAITOR
WITH ADDITION TANKS FOR SOFTENER
REEL FABRIC PLAITOR EXIT
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

ITEM 009
SANTEX CONVEYOR DRYER FOR OPEN WIDTH AND TUBULAR FABRIC
MODEL: SANTASHRINK 4/5240
YEAR: 1998
SANTEX CONTROLS
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION BAR ENTRY TO LATTICE ROLL GUIDER TO
• (2) SANTEX 2-ROLL PADS, RUBBER OVER RUBBER, 102” WIDE x 12” DIAMETER, STAINLESS STEEL PAN, 10-TON PAD, SWING-AWAY PAN, TENSION BAR WITH 2 STAINLESS STEEL MIXING TANKS, 75 GALLONS EACH
• DRIVEN SCROLL ROLLS WITH EDGE GUIDE CONTROL, WIDTH 95”
• OPERATOR’S PLATFORM
• PUP TENTER WITH KNIT ENTRY 45°, YEAR 1998, VERTICAL PIN CHAIN, 30’ LONG WITH TANDEMATIC PLATE GUIDES, RAIL GUIDES, PINNING BRUSHES, GUIDE SUPPORT FOR THE FABRIC, FABRIC CONVEYOR TO ENTER BOTH TUBULAR OR OPEN WIDTH FABRIC TO
• CONVEYOR DRYER 100” WIDE, 5 ZONES, 3-PASS WITH MAXON BURNERS, 5 CIRCULATING FANS TO CONVEYOR BELT TO PLAITOR
• ALL MOTORS AND SANTEX CONTROLS AND MONITORS
QUANTITY: 1

ITEM 010
SANTEX AG TUBULAR COMPACTOR MACHINE
MODEL: SANTASPREAD 140
YEAR: 1998
SANTEX CONTROLS
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSIONS BAR ENTRY
• OPERATOR’S PLATFORM
• TENSION DEVICE
• DRIVEN SPREADER BARS
• STEAMING DEVICE
• TUBULAR COMPACTING BENCH
• FELT BLANKET ONTO THE CONVEYOR BELT
• PRECISION PLAITOR
• TABELTOP ELECTRONIC SCALE
QUANTITY: 1

ITEM 011
COMET NAPPER
MODEL: PEGSO-X4
YEAR: 1998
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
24 ROLLS WITH TURNING BARS FOR TUBULAR 90” WIDE
XYCOM CONTROLS
12-BAG COLLECTION SYSTEM AND PLAITOR
YEAR: 1996
QUANTITY: 1

ITEM 012
STENTEX TENTER FRAME
MODEL: STENTOTHERM 3300
YEAR: 1999
STENTEX CONTROLS
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION ENTRY TO TEXT-STAR TYPE GUIDER TO 2 ROLL PAD
• ADDITION TANK TOP SCRAY PAD TO TEXT-STAR TYPE GUIDER
• TWO ROLL PAD R/R 10 TON
• OPERATOR’S PLATFORM
• WORKING WIDTH 1800mm
• HORIZONTAL PIN CHAIN, KNIT ENTRY
• TANDEMATIC SPLITLEVEL DECURLERS
• OVERFEED
• PINNING BRUSHES
• STEAM BOX
• RAIL GUIDERS, 20 FEET ENTRY, 8 ZONES
• 80 FEET HOUSING
• SCREEN MONITORS
• GAS FIRED, MAXON OVEPAK 408 BURNERS
• HONEYWELL CONTROLS
• 3 FEET COOLING ZONE
• 2 COOLING CANS, SELVEDGE TRIMMERS
• PLIATOR, SCRAY
• ZONE IN LINE INSPECTION BATCHER
QUANTITY: 1

ITEM 013
ZIMMER ROTARY SCREEN PRINTING MACHINE
MODEL: R92-S153
YEAR: 1993
COMPOSED OF:
• TENSION BAR SKY ENTRY
• SCRAY
• CORINO BRUSH
• CORINO PRINT GUIDER
• ZIMMER PRINTER, 8 COLOR, 86” BLANEKT
• PRINT CONVEYOR DRYER, 30’ LONG, 3-ZONE, GAS FIRED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

ITEM 014
SAFETY SWITCH BULLET NOSE SLITTER
MODEL: CUTTING
WITH REEL FABRIC PLIATOR
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

Learn More

REFERENCE NUMBER: T-1138

LORIS BELLINI APPC/LV 150 HANKS CABINET DYEING MACHINE, YEAR 1988 RECONDITIONED 2016

 

HANKS CABINET DYEING MACHINE

UNDER PRESSURE TEMPERATURE 110°C

WITH EXTRACTABLES BASKETS

MODEL LORIS BELLINI APPC/LV 150

YEAR 1988 FULLY RECONDITIONED 2016

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: T-1139

OBEM HANKS CABINET DYEING MACHINE, YEAR 1989 RECONDITIONED 2017

 

HANKS CABINET DYEING MACHINE

UNDER PRESSURE TEMPERATURE 110°C

WITH EXTRACTABLES BASKETS

BRAND OBEM

TYPE MBC 350/06/CE

YEAR 1989 FULLY RECONDITIONED 2017

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: M-4327

BENNINGER ZELL SIZING MACHINE MODEL BEN-SIZETEC WORKING WIDTH 2200mm YEAR 1994

 

BENNINGER ZELL SIZING MACHINE  MODEL BEN - SIZETEC WORKING WIDTH 2200 mm

YEAR  1994, WITH SECTIONAL AND FRACTIONAL SYSTEM.

N° A13715

MODEL  BB-S/ZT4/4/TKD

1 SECTIONAL BEAM UNROLLING DEVICE MODEL SWA WITH LOADING CELL FOR MEASURING

THE OUT GOING TENSION .

ELECTRO PNEUMATIC BREAKING SYSTEM

MAXIMUM BEAM DIAMETER 1000 mm.

1 FRACTIONAL BEAMING UNROLLING DEVICE WITH CAPACITY UP TO 20 POSITIONS

ELECTRO PNEUMATIC BREAKING SYSTEM

1 SIZING BOX MODEL TDK WORKING WIDTH 2200 mm. TOTAL WIDTH 2400 mm

STAINLESS STEEL BOX WITH TOTAL CAPACITY OF 240 LITERS WITH DIRECT STEAM INJECTION

LOWER VESSELS WITH INDIRECT HEAT SYSTEM

AUTOMATIC SIZE BOX FEEDING

HANDYMAT FOR START AND STOP AND MACHINE REGULATION

1 DRYING SECTION DEVICE MODEL ZT8 – WORKING WIDTH 2200 mm

6 DRYING STAINLESS STEEL CYLINDERS COVERED WITH TEFLON + 2 CYLINDERS WITHOUT TEFLON

4 ELECTRONIC TEMPERATURE REGULATIONS

2 AIR EXTRACTION

1 OIL/GREASE APPLICATION DEVICE MODEL CV

1 YARN SPLITTING DEVICE

7 RODS FOR SECTIONAL BEAMS

19 RODS FOR FRACTIONAL BEAMS

1 HUMIDITY MAHLO CONTROL DEVICE MODEL RMS-7S N°1670/1/10597

1 BEAM ROLLING DEVICE MODEL BB FOR BEAMS UP TO 1000 mm DIAMETER

YARN TRACTION MADE UP OF 3 ROLLS

1 PRESSURIZED ROLLER DEVICE

TENSION AND PRESSURE MEASURE DEVICES

AUTOMATIC BEAM LIFT DEVICE INCLUSIVE OF ADAPTORS FOR DIFFERENT BEAMS

EXTENSION REED FOR ENDS WIDTH CONTROL

MIRROR FOR EASY YARN CONTROL

1 HANDYMAT FOR START AND STOP AND MACHINE REGULATION

1 DUST SUCTION DEVICE

1 COMPLETE SIZE KITCHEN PREPARATION INCLUDING 2 TANKS FOR SIZE STORAGE

1 FULLY AUTOMATIC BENSIZETEC PROCESS CONTROL DEVICE INCLUDING HARDWARE AND SOFTWARE

1 EXTERNAL ELECTRIC CABINET.

Learn More