Search results for: 'cond'

NON-INVASIVE VENTILATOR
CERTIFICATE: CE
MEDICAL VENTILATOR
TECHNICAL PARAMETERS OF DOUBLE LEVEL VENTILATOR
VENTILATOR TYPE: ELECTRIC CONTROL
SCOPE OF APPLICATION: TREATMENT AND TITRATION OF SLEEP APNEA HYPOPNEA SYNDROME, SEVERE SNORING, AND RESPIRATORY INSUFFICIENCY.
DISPLAY INTERFACE: 3.5-INCH LED SCREEN, CHINESE OPERATING SYSTEM
*VENTILATION MODE: CPAP, S, S/T, T
PRESSURE RANGE:
PRESSURE RANGE: 4-30CMH2O (±0.5CMH2O)
PRESSURE ACCURACY: + 0.5CMH2O
PARAMETER SETTING:
DELAYED BOOST: 0-60MIN, SET THE DIVISION INTERVAL 5MIN
INITIAL PRESSURE: 4CMH2O TREATMENT PRESSURE / RESPIRATORY PRESSURE SETTING
THERAPEUTIC PRESSURE: 4-20CMH2O (IN CPAP MODE)
TARGET TIDAL VOLUME: 150ML - 1500ML, ON/ OFF
MAXIMUM SUCTION PRESSURE: 4-30CMH2O, (CAN BE SET WHEN THE TARGET TIDAL VOLUME FUNCTION IS ON)
MINIMUM SUCTION PRESSURE: 4-30CMH2O (NOT HIGHER THAN THE SUCTION PRESSURE), (CAN BE SET WHEN THE TARGET TIDAL VOLUME FUNCTION IS ON)
INSPIRATORY PHASE PRESSURE: 4-30CMH2O
EXPIRATORY PRESSURE: 4-30CMH2O
EXPIRATORY DECOMPRESSION: PATIENT, OFF, 1-3, THREE ADJUSTABLE
MANUAL VOLTAGE REGULATION: 0-2 GEAR, 0-2CMH2O (ONLY AVAILABLE IN CPAP MODE)
INSPIRATORY SENSITIVITY: 1-8 STALLS
EXPIRATORY SENSITIVITY: 1-8 STALLS
RESPIRATORY FREQUENCY: 3-40 TIMES / MIN
INSPIRATORY TIME: 0.3-3.0S
BACKUP RATE: ON / OFF, DEFAULT 10
PRESSURE RISE TIME: 1-4 STALLS
HUMIDIFIER: 1-5 ADJUSTABLE IN 5 GEARS
*TITRATION FUNCTION: SUPPORT MANUAL AND AUTOMATIC PRESSURE TITRATION, BUILT-IN REMOTE WIRELESS COMMUNICATION MODULE, COMPLETE THE RANDOM SWITCHING OF SINGLE AND DOUBLE LEVEL MODES IN THE TITRATION PROCESS, AND CONTROL MORE THAN 11 VENTILATOR PARAMETERS AT THE SAME TIME.
AUXILIARY FUNCTION: AUTOMATIC AIR LEAKAGE COMPENSATION, AUTOMATIC STARTUP, AUTOMATIC SHUTDOWN, DELAYED SHUTDOWN, SCREEN BACKLIGHT ADJUSTMENT
MONITORING PARAMETERS: PRESSURE, TIDAL VOLUME, RESPIRATORY RATE, MINUTE VENTILATION VOLUME, AIR LEAKAGE VOLUME, INSPIRATORY TIME, BLOOD OXYGEN SATURATION
WAVY CURVE: PRESSURE TIME WAVEFORM, FLOW RATE TIME WAVEFORM
ALARM PROMPT: PIPELINE AND MASK FALLING OFF, AIR LEAKAGE PROMPT, POWER INTERRUPTION, TREATMENT MACHINE FAILURE, HUMIDIFIER FAILURE, LOW VOLTAGE, HIGH RESPIRATORY RATE, LOW RESPIRATORY RATE, LOW MINUTE VENTILATION VOLUME, LOW BLOOD OXYGEN, REPLACEMENT OF FILTER COTTON, FULL SD CARD, RE INSERTION OF SD CARD
*DATA MANAGEMENT:
NETWORK DATA: BMC + RESPIRATORY HEALTH MANAGEMENT CLOUD PLATFORM
SD CARD DATA: RESART NPAP DATA ANALYSIS SOFTWARE
PARTS:
SD CARD: STANDARD
SD CARD SLOT: STANDARD
PIPING: 9 22MM, 1.8M LONG
FACE SHIELD: F2 NOSE MASK AS STANDARD
NOISE: LESS THAN 30DB
ENVIRONMENT CONDITION:
TEMPERATURE:
(WHEN USED) 5 -35 C
(DURING TRANSPORTATION AND STORAGE) -20 C -55 C
ATMOSPHERIC PRESSURE:
(WHEN USED) 760-1060HPA
(DURING TRANSPORTATION AND STORAGE) 760-1060HPA
WORKING HOURS: MORE THAN 8 HOURS
POWER SUPPLY REQUIREMENTS:
AC VOLTAGE: 100-240V
FREQUENCY: 50HZ/60HZ
INPUT POWER: LESS THAN 2A
WATERPROOF LEVEL: IP22 - DRIP PROOF EQUIPMENT
INSTRUMENT SIZE: 290mm X 180mm X 134mm
WEIGHT: 1.5KG (EXCLUDING HUMIDIFIER) 2.5KG (INCLUDING HUMIDIFIER)
ITEM 001
QUANTITY: 10 SETS-999 SETS
ITEM 002
QUANTITY: 1,000 SETS-9,999SETS
ITEM 003
QUANTITY: ≥10,000 SETS

CORDES LONG ARM REPAIR MACHINE
45 INCH THROAT
MODEL ALPHA I 900/45
208 VOLT

QUANTITY: 1

Fully tested.
Excellent working condition.

MAKE: GRIBETZ
MODEL: RELIANCE 4+
YEAR: 2006
220 VOLTS, 3-PHASE, 60 Hz
WIDTH: 90”
SPEED: 1200 RPM
QUANTITY: 1

WITH GRIBETZ PANEL CUTTER
MODEL: PANEL CUTTER 90
WIDTH: 90”
YEAR: 2005
QUANTITY: 1

IN GREAT RUNNING CONDITION
STATUS: CURRENTLY RUNNING, AVAILABLE IMMEDIATELY

ASK FOR VIDEOS

EACH LINE WITH
PRE-GRINDER
DENSIFIER, MODEL HV70
REGRINDING
COOLING
DOFFING

THERE IS A PULVERIZER AT THE END OF ONE OF THE LINES THAT IS AVAILABLE

HERBOLD RECENTLY INSPECTED AND INFORMED ALL BIG COMPONENTS ARE IN GOOD CONDITION, SOME SMALLER SPARE PARTS ARE ADVISED

QUANTITY: 2 LINES

MAKE: LAROCHE
MODEL: SUPER OLYMPIC
WIDTH: 1500mm
YEAR: MID 1980’S
6 CYLINDERS EACH LINE
CYLINDER DIAMETER: 1000mm
ALL CYLINDERS ARE DESIGNED FOR PINNED LAGS AND THERE IS LIFE LEFT IN MOST OF THE LAGS SETS.
LAGS: (1) 8mm x 135, (1) 10mm x 160, (1) 12 x 166, (3) 13mm x 174
EACH CYLINDER FED BY A FEED ROLL TO FEED DISH COMBINATION AND THE FIBER IS TRANSFERRED TO THE FOLLOWING CYLINDER VIA A CONDENSING SECTION.
MOTORS: 3 x 150 HP 575 VOLT
TOTAL REQUIRED POWER: 875 AMPS
NEW CONTROLS WITH ABB DRIVES
FEED CHUTES
LUMMUS BALERS
PINNED CYLINDERS
TEMAFA BLENDING BINS
EXIT CONVEYORS
EACH SECTION EQUIPPED WITH ANSUL DRY POWDER FIRE PROTECTION SYSTEM THAT IS ACTIVATED FROM EMBER DETECTED IN THE DUCT REMOVAL PIPING.
LINES INCLUDE ALL NECESSARY FANS, MAGNETS, DUCTING AND WIRING

IN PERFECT WORKING ORDER

QUANTITY: 2 LINES

R-4533 MAMMUT VMK SELECT DOUBLE LOCK CHAINSTITCH MULTI-NEEDLE QUILTER, YEAR 2014
2 BAR , 150m DISTANCE BETWEEN BARS
WIDTH UP TO 2700mm = 106 INCHES

MAMMUT VMK SELECT DOUBLE LOCK CHAINSTITCH MULTI-NEEDLE QUILTER
YEAR: 2014
96 SEPARATELY CONTROLLABLE NEEDLES
FULLY AUTOMATIC NEEDLE PLAN CHANGE
TOP AND BOTTOM THREAD CUTTER AT EACH SEWING POSITION
MATERIAL WIDTH UP TO 2700mm
TWO NEEDLE BARS
150mm SPACING
HANDWHEEL ADJUSTMENT OF HEIGHT OF PRESSER PLATE
ELECTRONIC THREAD BREAK DETECTOR FOR TOP AND BOTTOM THREADS
MATERIAL UNWIND DEVICE
RACKS FOR TOP AND BOTTOM THREAD
ONE CATWALK EACH ON FRONT AND REAR OPERATING SITE
TROUGH INFEED FOR UPPER MATERIAL WITH MOTOR-DRIVEN ROLLER SYSTEM
AUTOMATIC MARKING AND DETECTING UNIT FOR PATTERN CONFORM LATERAL CUT
ELECTRONICS AND MOTORS 400V, 3 PHASES
CONCRETE BASES AND VIBRATION DAMPERS

REFERENCE NUMBER: Z-1228

HEIDELBERG SPEEDMASTER 74 5HL, 530 X 740 MM (20X29"), YEAR 2011 – WITH 5 COLORS

5-COLOR HEIDELBERG SPEEDMASTER 74 5HL

YEAR: 2011

530 X 740 MM (20X29")

APPROX. 58 MIO. IMPR.

DISMANTLED AND CLEANED

MACHINE IS IN GOOD CONDITION AND CAN BE INSPECTED

TOTAL QUANTITY: 1

REFERENCE NUMBER: P-5392

FEHRER NL28 PRE NEEDLE LOOM WIDTH 2600mm

FEHRER

TYPE: NL28

PRE NEEDLE LOOM

WORKING WIDTH: 2600mm

SINGLE BOARD

QUANTITY: 1

REFERENCE NUMBER: R-9512
HEIDELBERG SM102ZP 
YEAR 1992
QUANTITY: 1

REFERENCE NUMBER: M-7826

SAURER EPOCA-3 PENTACUT SINGLE EMBROIDERY HOOP COMPUTERIZED SHUTTLE EMBROIDERY MACHINE YEAR 2003

COMPUTERIZED SHUTTLE EMBROIDERY MACHINE

MAKE: SAURER

MODEL: EPOCA III PENTACUT (SINGLE EMBROIDERY HOOP)

WORKING SPEED: 420 REVOLUTION

YEAR: 2003

QUANTITY: 1