Search results for: 'F&k+c''

C-2371 KARL MAYER WARPING MACHINE GSP 50, 30" X 50" AND ALUCOLOR BEAM, 21" X 21" - PACKAGE

Compare

REFERENCE NUMBER: C-2371 KARL MAYER WARPING MACHINE GSP 50, 30" X 50" AND ALUCOLOR BEAM, 21" X 21" - PACKAGE DETAILS: WARPER BRAND: KARL MAYER TYPE: GSP 50 30" X 50" CAN SUPPORT BEAMS WIDTH: UP TO 50" AND FLANGE DIAMETER UP TO 30" OR 2 BEAMS 21” X 21” AT SAME TIME WITH COMPLETE 1200 ENDS CREEL AND FULL ACCESSORIES IN COMPLETE CONDITION QUANTITY: 2 ALUCOLOR BEAM 21" X 21" QUANTITY: 200 QUANTITY AVAILABLE: 1 Learn More

T-6552 MASK AIR TIGHTNESS TESTER

Compare

REFERENCE NUMBER: T-6552

MASK AIR TIGHTNESS TESTER

HOW TO CHOOSE A HIGH-QUALITY MASK NOT ONLY DEPENDS ON THE FILTERING EFFICIENCY OF THEMASK, BUT ALSO TO CONFIRM WHETHER THE MASK IS COMPLETELY IN CONTACT WITH THE FACE, OTHERWISE AEROSOL PARTICLES SUCH AS GERMS THAT HAVE NOT BEEN FILTERED BY THE MASK WILL BE INHALED FROM THE INADEQUATE ADHESION. THEREFORE, IT IS VERY IMPORTANT TO CHECK THE WEARING STATUS OF THE MASK. THE EUROPEAN AND AMERICAN COUNTRIES HAVE LISTED THE APPLICATION TEST OF THE MASK AS A STRONG INSPECTION ITEM.

FOR EXAMPLE, THE N95 MASK IS ONE OF 9 TYPES OF PARTICULATE PROTECTIVE MASKS CERTIFIED BY NIOSH (NATIONAL INSTITUTE OF OCCUPATIONAL SAFETY AND HEALTH). "N" INDICATES OIL RESISTANCE."95" INDICATES THAT THE PARTICLE CONCENTRATION IN THE MASK IS MORE THAN 95% LOWER THAN THAT OF THE PARTICLES OUTSIDE THE MASK WHEN EXPOSED TO THE SPECIFIED NUMBER OF SPECIAL TEST PARTICLES. N95 IS NOT A SPECIFIC PRODUCT NAME, AS LONG AS IT MEETS THE N95 STANDARD AND PASSES THE NIOSH REVIEW, IT CAN BE CALLED "N95 MASK".

N95 TYPE MASKS, IN ADDITION TO THE FILTERING EFFICIENCY OF THE MASKS, THE CLOSENESS OF THE MASKS TO THE FACE IS ONE OF THE IMPORTANT FACTORS THAT DETERMINE THE EFFECTIVENESS OF THE USE OF THE MASKS. THE SUITABILITY OF DIFFERENT TYPES OF MASKS FOR THE HUMAN FACE VARIES GREATLY.

THEREFORE, BEFORE USING A MASK, THE SUITABILITY OF THE MASK SHOULD BE CHECKED FIRST. DURING THETIGHTNESS TEST OF THE WEARER'S FACE, ENSURE THAT AIR CAN PASS IN AND OUT THROUGH THE MASK WHEN IT IS CLOSE TO THE EDGE OF THE FACE. THE MASK TIGHTNESS TESTER CAN QUICKLY COMPLETE THE TIGHTNESS TEST OF RESPIRATORS SUCH AS MASKS TO ENSURE THAT IT PROVIDES GOOD PROTECTION PERFORMANCE. IT CONFORMS TO THE CHINESE RESPIRATOR STANDARD GB2626-2019 STANDARD, OSHA / CSA STANDARD AND CHINA GENERAL ADMINISTRATION OF QUALITY SUPERVISION, INSPECTION AND QUARANTINE "GB 19083-2010 TECHNICAL REQUIREMENTS FOR MEDICAL PROTECTIVE MASKS" JOINTLY ISSUED BY THE CHINA NATIONAL STANDARDIZATION ADMINISTRATION COMMITTEE.

ADHESION (SUITABILITY TEST): THE MASK DESIGN SHOULD PROVIDE GOOD ADHESION. THE OVERALL FIT FACTOR OF THE MASK SHOULD NOT BE LESS THAN 100. THIS TEST THE REQUIREMENTS WERE FORMALLY IMPLEMENTED ON AUGUST 1, 2011.

MASK TIGHTNESS TESTER USES CNC TECHNOLOGY, SUITABLE FOR 100 / 99 / P3 / HEPASERIES MASKS DISPOSABLE FILTER MASK TIGHTNESS TEST (INCLUDING DISPOSABLE DUST MASKS SUCH ASN95 / N90 / KN95), GAS MASKS / BREATHING MASKS, ADHESIVENESS TEST OF HALF-MASK AND FULL FACE MASK, INDEPENDENT OR COMPUTER CONTROL, FIVE LANGUAGES SWITCH DISPLAY, EQUIPPED WITH MULTIPLE COMMUNICATION INTERFACES (USB, ETHERNET), WIFI CAN ALSO BE ENABLED, ONE COMPUTERCAN CONTROL FOUR INSTRUMENTS AT THE SAME TIME.

PARAMETER:

CONCENTRATION RANGE: 0 ~ 100,000 / CM3

GRAIN DIAMETER: 0.02 ~ 1.0^M

FLOW: SAMPLING FLOW: 100CM3 / MIN

TOTAL FLOW: 700CM3 / MIN

CLOSENESS COEFFICIENT TEST: DIRECT TEST (COUT/ CIN)

LIQUOR: 99.5% + ISOPROPANOL (ANALYTICAL GRADE)

DISPLAY: 7INCH TRUE COLOR TOUCH SCREEN

COMMUNICATION INTERFACE: USB X 3 (HOST X 2,DEVICE X 1) ETHERNET INTERFACE X1

CONNECTION PORT: ENVIRONMENT PORT, SAMPLING PORT

WIFI: EQUIPPED

LANGUAGES: ENGLISH, FRENCH, SPANISH, PORTUGUESE, CHINESE

FLOW CONTROL: SENSOR CONTROL

PC CONTROLLABLE OPERATION: ONE COMPUTER CAN CONTROL 4 INSTRUMENTS AT THE SAME TIME

DATA OUTPUT FORMAT: MICROSOFT EXCEL

WORKING TEMPERATURE: 15 ~ 35 °C

POWER SOURCE: AC 110 —240V 50 / 60HZ

APPEARANCE SIZE: 208 X 117 X 262MM

WEIGHT: 2.1KG

ACCESSORIES: ALCOHOL REAGENT BOTTLE, PROTECTIVE CAP, REAGENT STICK, ZERO-COUNT FILTER, STRAINER, SAMPLING TUBE, INSTRUCTION MANUAL, AC ADAPTER, TOUCH SCREEN PEN, OPTIONAL COMPUTER.

OPTIONAL: TEST KIT FOR TIGHTNESS COEFFICIENT

IN ORDER TO PREVENT INFECTION AT THE MEDICAL SITE AND DURING LABOR WORK, WORKERS MUST BE PROTECTED FROM INHALABLE HAZARDOUS SUBSTANCES IN THE WORKPLACE, AND RESPIRATORS SUCH AS MASKS MUST BE WORN DURING WORK.

SELECT A RESPIRATOR, SUCH AS A MASK, BASED ON YOUR FACIAL FEATURES, AND EVALUATE THE TIGHTNESS BETWEEN THE RESPIRATOR, SUCH AS A MASK AND THE FACE, TO CHECK WHETHER THERE ARE GAPS OR LEAKS THAT PUT WORKERS AT RISK. THE MASK TIGHTNESS TESTER CAN QUICKLY COMPLETE THE TIGHTNESS TEST OF RESPIRATORS SUCH AS MASKS TO ENSURE THAT IT PROVIDES GOOD PROTECTIVE PERFORMANCE. SECURITY EXPERTS WILL ALSO DEVELOP PROTECTION SCHEMES AND STANDARD REGULATIONS BASED ON THE RESULTS OF THE TIGHTNESS TEST. WIDELY USED IN HOSPITALS, MANUFACTURING PLANTS, PRODUCTION SITES, FIREFIGHTING WORKPLACES AND OTHER OFFICIAL TESTING AGENCIES.

MASK TIGHTNESS TESTER FEATURES:

• QUANTITATIVE TIGHTNESS TEST FOR RESPIRATORS SUCH AS MASKS (QNFT)

• APPLICABLE TO 100/99 / P3 / HEPA SERIES MASK DISPOSABLE FILTER MASK TIGHTNESS TEST (INCLUDING N95 / N90 / KN95 AND OTHER DISPOSABLE DUST MASKS)

• ADHESION TEST OF HALF MASK AND FULL FACE MASK

• GAS MASK TIGHTNESS TEST

• PAPR MASK TIGHTNESS TEST

• SCBA RESPIRATOR MASK TIGHTNESS TEST

• 7INCH TRUE COLOR TOUCH SCREEN

• INDEPENDENT OR COMPUTER CONTROLLED

• USING CNC TECHNOLOGY

• ENGLISH, FRENCH, SPANISH, PORTUGUESE, CHINESE LANGUAGE SWITCHING DISPLAY

• COMPLIES WITH US OSHA STANDARDS, CANADIAN STANDARDS ASSOCIATION (CSA) GUIDELINES, INCLUDING N95

• EQUIPPED WITH A VARIETY OF COMMUNICATION INTERFACES (USB, ETHERNET), AND CAN ALSO ENABLE WIFI

• ONE COMPUTER CAN CONTROL FOUR INSTRUMENTS AT THE SAME TIME

QUANTITY: 1

Learn More

M-5350 BRUCKNER MULTILAYER STENTER FOR KNIT AND WOVEN FABRIC YEAR 1995 WIDTH 2200mm

Compare

REFERENCE NUMBER: M-5350 (220LWGPXX1) L BRUCKNER MULTILAYER STENTER FOR KNIT AND WOVEN FABRIC YEAR 1995 WIDTH 2200mm MULTILAYER STENTER MACHINE FOR KNITTING FABRIC AND WOVEN FABRIC MANUFACTURE: BRUECKNER YEAR: 1995 WORKING WIDTH: 2200mm QUANTITY AVAILABLE: 1 Learn More

M-4038 BENNINGER ZELL MERCERIZER YEAR 2007 WIDTH 1800mm

Compare

REFERENCE NUMBER: M-4038

BENNINGER ZELL MERCERIZER YEAR 2007 WIDTH 1800mm

BRAND: BENNINGER ZELL

MODEL YEAR: 2007

ROLLER WIDTH: 2000mm

WORKING WIDTH: 1800mm

TOTAL FABRIC QUANTITY: 160 METERS

SEARCH FOR PRE-WETTING AND IS LOCATED AT THE ENTRANCE TIGHTENING.

MERCERIZED PART: TWO-CHAN, ARE TIGHTENING INTERMEDIATE OUTPUT.

BENNINGER HAS BOMA CONTROL SYSTEM

STABILIZE KISMI : A CHAN , OUTPUT ARE TIGHTENING SEARCH

ELUTING FRACTION CAN OPERATE INDEPENDENTLY

THE MACHINE ONLY FOR THE PURPOSE OF DESTROYING THE AVAILABLE

ELECTRICAL PANEL HAS BEEN DESIGNED ACCORDINGLY BY BENNINGER

WASHING BOATS: FOUR PIECE, BENNINGER WASHING TECHNIQUES APPROPRIATE TO EACH, DOUBLE FABRIC PASS, SEARCH TOP SQUEEZE, INDIRECTLY HEATED, DIRECT WATER SUPPLY AND CHEMICALS SHOULD BE FED TWO BOAT.

EVERY BOAT OUT THERE IN THE FABRIC OPENING AND INTERMEDIATE CLAMPING UNITS HAVE.

THE LAST BOAT IS IN ITSELF CONSISTS OF TWO PARTS, THE BATHROOMS DO NOT MIX.

THE NEUTRALIZATION CAN BE PERFORMED IN THE LAST COMPARTMENT.

THERE ARE AUTOMATIC ACID DOSAGE UNIT.

THERE ARE 7.5 KN CLAMPING CYLINDER IN THE OUTPUT SECTION.

SEARCH SQUEEZED FABRIC FROM THE FABRIC CENTERING.

THROUGH THE WINDER UNIT IS WRAPPED IN THE DOCK

Learn More

M-5300 UNDER PAD PRODUCTION LINE

Compare

REFERENCE NUMBER: M-5300 (131342BVGT12UF) L UNDER PAD PRODUCTION LINE UNDER PAD PRODUCTION LINE MODEL: 100CD PRODUCTS TO BE PRODUCED: 3 SIZES OF DISPOSABLE UNDER PAD (SIZE: 600x900mm, 600x600mm, 600x400mm) MECHANICAL DRIVING SYSTEM WITH INVERTER CONTROL PRODUCT STRUCTURE: FLUFF +SAP; TOP TISSUE; BOTTOM TISSUE; TOP SHEET; BACK SHEET QUANTITY AVAILABLE: 1 Learn More

P-2121 RIETER D30 DRAW FRAMES YEAR 2001

Compare

REFERENCE NUMBER: P-2121 RIETER D30 DRAW FRAMES YEAR 2001 RIETER TYPE: D30 DRAW FRAMES YEAR: 2001 SUITABLE FOR COTTON, POLYESTER OR MIXED UP TO 80mm SPEED 250 to 1000 M/MIN DRAFTING 3 OVER 3 PRESSION BAR REGULATION – ELECTRONIC INTEGRATED DUST ASPIRATION AUTOMATIC CAN CHANGER 18 INCHES x 42 INCHES CAN SIZE CREEL WITH SENSORS RIETER QUALITY MONITORS VOLTAGE: 220 VOLTS, 60 HERTZ 11.6 KILOWATTS POWER PNEUMATIC DRAFTING SYSTEM RSB D30 YEAR 2001 CARDS: C 1/2 – 1976 - COTTON C 1/3 – 1984 – POLYESTER C 1/3 – 1982 – POLYESTER ADDITIONAL DRAW FRAMES: 2 DO/2 YEAR: 1985 QUANTITY AVAILABLE: 2 Learn More

M-1689 FLEISSNER CLOSED TYPE SIEVE-DRUM DRYER YEAR 2008 WIDTH 3500mm

Compare

REFERENCE NUMBER: M-1689 (660YSHDXX5) FLEISSNER CLOSED TYPE SIEVE-DRUM DRYER YEAR 2008 WIDTH 3500mm CLOSED TYPE SIEVE-DRUM-DRYER MAKE FLEISSNER QUANTITY AVAILABLE: 1 Learn More

J-2375 COMPLETE CERAMIC TILE PRODUCTION PLANT, PRODUCTION 7 MILLION SQUARE METERS PER YEAR

Compare

TILE FACTORY DESIGNED BY SACMI / ITALY
YEAR ESTABLISHED 2014 TO 2016
THIS PLANT IS AN ENVIRONMENTALLY FRIENDLY ENTERPRISE, WHEN IT RECYCLES 100% OF ITS EFFLUENTS AND PERFORMS HEAT RECOVERY, THEREBY SAVING ENERGY

See all pictures:
https://www.flickr.com/photos/183869481@N08/albums/72157710649767958

THE PLANT:
COVERS AN AREA OF 22 THOUSAND SQUARE METERS
THE PRODUCTION CAPACITY IS 7 MILLION SQUARE METERS / YEAR
CERAMIC FLOOR TILES
CERAMIC WALL TILES
BMR POLISHING LINE
BMR SQUARING & CHANFERING LINE
THE MAIN RAW MATERIALS ARE CLAY (DB-4) - 31 %, ALBITE (STD5) - 60 %
NEPHAIIN (PN9595) - 2.5 %, KAOLIN (RHB1) - 6.5 %
ON TOP OF IT THEY ARE USING GLAZE MATERIALS AND PAINTS
•FROM THE MOMENT THE MATERIAL IS PREPARED IT IS BEING DRIED PRESSED ON ONE OF FOUR (4) PRODUCTION LINES.
•TWO (2) LINES ARE WITH SACMI PRESSES OF PH 7,500 TON EACH AND HORIZONTAL DRYERS SACMI
•TWO LINES ARE WITH SACMI PRESSES OF PH 3,590 TON EACH AND VERTICAL DRYERS SACMI
•ALL FOUR (4) LINES HAVE THEIR OWN DIGITAL PRINTING MACHINE INCORPORATED
•ALL PRODUCTS ARE BEING GLAZED AND FIRED ON 1200 DEGREES IN ONE OF THE TWO (2) KILNS, SACMI
FOUR (4) SORTING, PACKING AND PALLETIZING LINES
GLAZE PREPARATION LINE
COMPLETE INSTALLATION FOR SMALL PRODUCTION CAPACITIES
COMPLETE FOILING LINE
COMPLETE ELECTRIC INSTALLATION
POWER GENERATOR UNIT
COMPRESSED AIR INSTALLATION

MACHINES ARE MADE BY:
SACMI: ITALY
NUOVA ERA / ROBOBOX: ITALY
BMR: ITALY
IN.TE.SA: ITALY
CUCCOLINI: ITALY
SYSTEM CERAMICS: ITALY
TGMAC SR.L: ITALY
DURST: GERMANY
ROTOCOLOR MAG: ITALY
NUOVA FIMA: ITALY
OMS: ITALY
MARPAK OMS: ITALY
MESSERSI PACK: ITALY

TILE SIZES
THE FACTORY MANUFACTURES TILES OF VARIOUS SIZES FROM 300 X 300 TO 1200 X 1200mm IN VARIOUS TEXTURES AND DESIGNS USING DIGITAL PRINTING MACHINES
PRODUCTION CAPACITY IS 7 MILLION SQUARE METERS / YEAR
THE FACTORY IS FULLY AUTOMATED AND USING ADVANCED CONTROL SYSTEMS!

HUGE AMOUNT OF ORIGINAL SPARE PARTS AVAILABLE WITH THIS PLANT
THIS PLANT IS AVAILABLE WITH THE COMPLETE ELECTRIC, AIR, GAS, RECYCLING INSTALLATION

THIS PLANT CAN BE SOLD: WITH 4 LINES OR 2 AND 2 LINES

Learn More

C-1175 MOERS-BEYSS KIER DECATIZING MACHINE VAPERMAT 1200, YEAR 1995, WIDTH 1800mm

Compare

REFERENCE NUMBER: C-1175 MOERS-BEYSS KIER DECATIZING MACHINE VAPERMAT 1200, YEAR 1995, WIDTH 1800mm COMPOSED OF: MOERS-BEYSS DECATIZING LINE IN AUTOCLAVE TYPE KD MODEL VAPERMAT 1200 YEAR OF CONSTRUCTION 1995 ROLLERS 1800MM (WIDTH OF SATIN FABRIC) ENTRY FRAME WITH FABRIC BRAKE ADJUSTABLE SYSTEM WEFT STRAIGHTNER BIANCO WITH PINS WHEELS MODEL TRAMATEX AUTOCLAVE DECATIZING DRUM DIA. 1200MM DELIVERY FABRIC IN FOLDING DEVICE QUANTITY AVAILABLE: 1 Learn More

PP-1136 OTHER MISCELLANEOUS INVENTORY FROM MATTRESS PLANT

Compare

SABA AQUABON 3361-264 GALLON TOTE
QUANTITY: 190

SABA ACTIVATOR 3914-273 GALLON TOTE
QUANTITY: 500

SPUNFAB ADHESIVE 415LPA/1
QUANTITY: 4,250

LAW LABEL-MATT,BS,FD
QUANTITY: 28,641

I-410XLW (#738G) TWIN XL/FULL XL INSTAMATIC FRAME 4 LEGS
NEED COUNT

I-PK465 (#777G) KING/CK INSTAMATIC FRAME 6 LEGS
NEED COUNT

I-34G TWIN/FULL INSTAMATIC FRAME 4 LEGS
NEED COUNT

#666 (J6MB66) 6/6 ALL STEEL BED BASE 6”
NEED COUNT

576 #140/76 HOOK-ON 76” RAIL
NEED COUNT

575 #145/75 BOLT-ON 76” RAIL
NEED COUNT

582 Q/K HOOK-ON 82” RAIL (5/0 & , XL)
NEED COUNT

581 Q/K BOLT-ON 82” RAIL MANUTA
NEED COUNT

Learn More