Search results for: 'reference number -v-'

C-4022 SOMET SUPER-EXCEL AND ALPHA LOOMS, WIDTH 3200mm, YEAR 2001 TO 2003, JACQUARD

OFFER 001
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 002
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 003
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 004
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 005
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 006
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 007
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 008
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 009
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 010
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 011
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 012
SOMET SUPER-EXCEL LOOM
YEAR: 2002
WIDTH: 3200mm
OFFER 013
SOMET SUPER-EXCEL LOOM
YEAR: 2001
WIDTH: 3200mm
OFFER 014
SOMET SUPER-EXCEL LOOM
YEAR: 2001
WIDTH: 3200mm
OFFER 015
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 016
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 017
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 018
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 019
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 020
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 021
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 022
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 023
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 024
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 025
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 026
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 027
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 028
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 029
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 030
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 031
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 032
SOMET SUPER-EXCEL LOOM
YEAR: 2003
WIDTH: 3200mm
OFFER 033
SOMET SUPER-EXCEL LOOM
YEAR: 2001
WIDTH: 3200mm
OFFER 034
SOMET SUPER-EXCEL LOOM
YEAR: 2001
WIDTH: 3200mm
OFFER 035
SOMET ALPHA JACQUARD LOOM
WIDTH: 3200mm
OFFER 036
SOMET ALPHA JACQUARD LOOM
WIDTH: 3200mm
OFFER 037
SOMET ALPHA JACQUARD LOOM
WIDTH: 3200mm
OFFER 038
SOMET ALPHA JACQUARD LOOM
WIDTH: 3200mm
OFFER 039
SOMET ALPHA JACQUARD LOOM
WIDTH: 3200mm
OFFER 040
SOMET ALPHA JACQUARD LOOM
WIDTH: 3200mm
OFFER 041
SOMET ALPHA JACQUARD LOOM
WIDTH: 3200mm
OFFER 042
SOMET ALPHA JACQUARD LOOM
WIDTH: 3200mm

Learn More

JASON LIST# 1472
FACE MASK TYPES

REFERENCE NUMBER: MASK-1111
FLAT, SURGICAL MASK, 3-PLY NONWOVEN SPUNBOND, MELTBLOWN AND SPUNBOND

REFERENCE NUMBER: MASK-1112

REFERENCE NUMBER: MASK-1113

REFERENCE NUMBER: MASK-1121
SEE J-2756 FOR THE LINE THAT PRODUCES THESE

REFERENCE NUMBER: MASK-1115
KN95 MEDICAL MASKS (PARTICULATE RESPIRATORS)

REFERENCE NUMBER: MASK-1116
N95 MEDICAL MASKS (PARTICULATE RESPIRATORS)

REFERENCE NUMBER: MASK-1117
FFP2 MEDICAL MASKS (PARTICULATE RESPIRATORS)

REFERENCE NUMBER: MASK-1118
3M MODEL 1860 MEDICAL MASKS (PARTICULATE RESPIRATORS)

REFERENCE NUMBER: MASK-1119
3M 8577 MEDICAL MASKS (PARTICULATE RESPIRATORS)

REFERENCE NUMBER: MASK-1120
3M 9541V MEDICAL MASKS (PARTICULATE RESPIRATORS)

REFERENCE NUMBER: MASK-1124
3M 1870 HEALTH CARE PARTICULATE RESPIRATOR & SURGICAL MASK

REFERENCE NUMBER: MASK-1122
3M 1860S HEALTH CARE PARTICULATE RESPIRATOR & SURGICAL MASK

REFERENCE NUMBER: MASK-1123
3M 1860 HEALTH CARE PARTICULATE RESPIRATOR & SURGICAL MASK

More information is available upon request.
E-mail us for price, pictures, video, or diagram.
Include our reference number.

Learn More

LIST NUMBER: L-2987
SIZING MACHINES FOR SALE

REFERENCE NUMBER: P-6749
ROTAL
SIZING MACHINE
YEAR: 1990
QUANTITY: 1

REFERENCE NUMBER: P-7175
BENNINGER ZELL
SIZING
YEAR: 1994
HEAD STOCK WORKING WIDTH: 2800mm
QUANTITY: 1

REFERENCE NUMBER: P-5168
SUCKER
MODEL: MOENUS Z 14
SIZZING MACHINE
WIDTH: 3400mm

BENNINGER
TYPE: BEN DIRECT
WARPER
QUANTITY: 1

REFERENCE NUMBER: P-5818
SUCKER MULLER
SIZING 2 SIZING BOX WIH BENNINGER DIRECT WARPER
YEAR: 1989
WIDTH: 130 INCHES
QUANTITY: 1

REFERENCE NUMBER: P-5586
BENNINGER-ZELL
WARP SIZING LINE
YEAR: 1994
WORKING WIDTH: 3400mm
QUANTITY: 1

REFERENCE NUMBER: C-1229
SUCKER MULLER SIZING MACHINE
MODEL ZG6
YEAR 1984
WORK WIDTH 3000mm
SCHLAFHORST DIRECT WARPING MACHINE MODEL MZD
YEAR 1984
WORK WIDTH 1600mm
QUANTITY: 1

REFERENCE NUMBER: R-1913
SUCKER SIZING
WORKING WIDTH: 3300mm
QUANTITY: 1

REFERENCE NUMBER: R-3193
BENNINGER SIZING MACHINE
TYPE: BEN-SIZE TEC A13
YEAR: 1994
HEADSTOCK WIDTH: 3400mm
QUANTITY: 1

REFERENCE NUMBER: P-3562
WEST POINT
MODEL: 861
SLASHER
YEAR: 1993
HEADWAY WIDTH: 126 INCHES
QUANTITY: 1

Learn More

LIST NUMBER: L-3004
SIZING MACHINES FOR SALE

REFERENCE NUMBER: C-5212
BENNINGER SIZING MACHINE
TYPE BEN SIZETEC
YOM: 2004
WORKING WIDTH: 2400mm
BENINGER DIRECT WARPER
TYPE BEN DIRECT
YOM: 2005
WORKING WIDTH: 2400mm
QUANTITY: 1

REFERENCE NUMBER: P-4682
BENNINGER
SIZING MACHINE
YEAR: 2002
WIDTH: 2800mm
QUANTITY: 1 SET

REFERENCE NUMBER: P-7130
SUCKER MULLER
TYPE: HACOBA
SIZING MACHINE
YEAR: 1999
WORKING WIDTH: 1800mm
QUANTITY: 1

REFERENCE NUMBER: C-3650
OFFER 001
SUCKER MOENUS Z 14 SIZING MACHINE
WIDTH: 3400mm
YEAR: 2006
QUANTITY: 1
OFFER 002
BENNINGER BEN DIRECT WARPING MACHINE
YEAR: 2005
WIDTH: 2200mm
QUANTITY: 1

REFERENCE NUMBER: A-1197 (1212GHBXX11) A
MAKE: BENNINGER
MODEL: BEN SIZETEC
YEAR: 1998
Width - 2000mm
QUANTITY: 2

REFERENCE NUMBER: P-6712
SUCKER MULLER
SIZING MACHINE
YEAR: 2003
HEADSTOCK WIDTH: 3600mm
QUANTITY: 1

REFERENCE NUMBER: M-5040
(1 SET) BENNINGER SIZING MACHINES (SLASHERS), YEAR 2000

REFERENCE NUMBER: R-3746
ITEM 001
KARL MAYER​ DIRECT WARPING ​MACHINE
YEAR: 20​06​
WIDTH: 2​0​00mm
​QUANTITY: 1 SET
ITEM 002
KARL MAYER SIZING MACHINE
YEAR: 2011
QUANTITY: 1 SET

Learn More

R-1170 DELL’ ORCO VILLANI RAG TEARING LINE + BALE PRESS, YEAR 1989 TO 1999

DETAILS:
DELL’ ORCA VILLANI RAG TEARING LINE + BALLING MACHINE
COMPOSED BY:
ITEM 001
DELL’ ORCA VILLANI CUTTERS
YEAR: 1989
QUANTITY: 2

ITEM 002
DELL’ ORCA VILLANI MIXING ROOMS + BIN EMPTIER
TYPE: FA/3030/T
QUANTITY: 2

ITEM 003
DELL’ ORCA VILLANI VOLUMATIC FEEDER
MODEL: CARICATORE
TYPE: CS/1600
YEAR: 1999
QUANTITY: 1

ITEM 004
DELL’ ORCA VILLANI RAG TEARING MACHINE
4 CYLINDERS
YEAR: 1999
WIDTH: 1500mm
EACH DRUM MODEL: M/1500
TYPE: SFILACCIATRICE
QUANTITY: 1

ITEM 005
DELL’ ORCA VILLANI VOLUMATIC FEEDER
MODEL: CARICATORE
TYPE: CS/1600
YEAR: 1989
QUANTITY: 1

ITEM 006
DELL’ ORCA VILLANI RAG TEARING MACHINE
3 CYLINDERS
YEAR: 1989
WIDTH: 1500mm
EACH DRUM MODEL: M/1500
TYPE: SFILACCIATRICE
QUANTITY: 1

ITEM 007
DELL’ ORCA VILLANI BALE PRESS
TYPE: RA/100
WITH 2 CHAMBERS (ROTATIVE SYSTEM)
WITH WEIGHING DEVICE (SCALE FOR KG OF EACH BALE)
QUANTITY: 1

ITEM 008
DELL’ ORCA VILLANI DUST COLLECTING INSTALLATION
WITH BAGS TO COLLECT THE DUST
QUANTITY: 1

QUANTITY: 1 LINE

Learn More

REFERENCE NUMBER: M-3513 (880JJHGHH7) L VOLKMANN VTS-05-0-C CABLERS & TWISTERS YEAR 1999-2008 – 120 SPINDLES VOLKMANN VTS-05-0-C 1999 CABLER 120 SPINDLES VOLKMANN VTS-05-0-C 2000 CABLER 120 SPINDLES VOLKMANN VTS-05-0-C 2007 CABLER 120 SPINDLES VOLKMANN VTS-05-0-C 2008 CABLER 120 SPINDLES VOLKMANN VTS-05-0 2003 TWISTER 120 SPINDLES VOLKMANN VTS-05-0-C 2000 CABLER 120 SPINDLES VOLKMANN VTS-05-0 2002 TWISTER 120 SPINDLES VOLKMANN VTS-05-0 2002 TWISTER 120 SPINDLES QUANTITY AVAILABLE: 8 Learn More

REFERENCE  NUMBER:  G-0784

RIETER FDY  EXTRUSION EQUIPMENT FOR POLYPROPYLENE YEAR 1996/98

 

1. Machine m26/39:

Year 1996

For 1 fdy spinning line with 2+4 positions, each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  800 mm

Spinning pump capacity:  4x10 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  670 mm

Quench length:  1700 mm

Number of spin-finish pumps per position:  1

Capacity of spin-finish pump:  4x0.05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

Extruder for 4 positions Year 1998:

 

1 extruder type e1. 105-30m:

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  105 mm

-l/d ratio:  30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 58 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 95kw

-extruder frame

 

1 extruder measuring head, dowtherm vapour heated

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

Extruder for 2 positions Year 1998:

1 extruder type e1. 60-30

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  60 mm

-l/d ratio:  30

-barrel with

                electrical ceramic heaters

                6 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 17 kw

                inlet zone, water cooled

                insulation

-screw nitrited with maddock mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated year 1998

-measuring head comprising:

                insulation

Double pt100, one each for melt and dowtherm vapour temperature

                                pressure sensors for melt pressure

                burst disc for power switch-off at overpressure.

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam year 1998

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 25 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled level gauge

- vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

-max pressure in the spinpack:  350 bar

-design temperature:  320 °c

-spinneret outside dimensions:  95 mm

-bottom loading design

-bayonet locking, insert and tighten by turning 90°

-self sealing system

-sand or metal powder filtration, 3 cm filling depth

-wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 6 ccm/rev

Each spin pump system comprising

Individual drive motor with flange connection to the reduction gear

Hollow gear shaft for installation of spin pump shaft

Shaft with shear pin protection

Reduction ratio 1:80

Pump speed:  8-30 rev/min

Motor type:  synchronous ac-motor

Rated power:  500w at 50 cps

 

Quench air cabinets bsk 670/1700:

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                4 spin finish application nozzles

                1 yarn cutter / aspirator unit

                1 spin finish pump

                4 centring yarn guides

                4 intermingling units

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls year 1998:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speed range:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60 hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ±0.2 mm

Tube outside diameter:  106 ±0.4 mm

Tube length:  225 ±0.5 mm

 

Oil-mist lubrication unit:

Compressed air distribution station

Mobile aspirator guns with hoses

Electrical control equipment

-for electrical power

                general:  3 x 380v/50hz plus ground wire

                euro-standard:  3x400v 50 or 60hz plus ground wire

                maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation:  ±2%

 

Process control system (cif):

                fully integrated control system to control and monitor the entire spinning line.

                the central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control year 1998:

 

Spinning section:

Speed adjustment for the extruder motor is done via a dc-convertor

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor. While current flows, a voltage is inducted into the

Rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

2. Machines m27/ 28 / 30 year 1998:

For 3 fdy spinning lines each with 2 positions, and each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  1000 mm

Spinning pump capacity:  4x7.5 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  470 mm

Quench length:  1200 mm

Number of spin-finish pumps per position:  2

Capacity of spin-finish pump:  4x0.16 ccm/rev + 4x0,05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

 

1 extruder type e1. 60-30m

-nominal extruder capacity:  max 80 kg/h for pp

-screw diameter:  65 mm

-l/d ratio: 30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 22 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated:

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated:

Melt distribution system comprising:

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam:

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 18 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled

-level gauge

-vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

Max pressure in the spinpack:  350 bar

Design temperature:  320 °c

Spinneret outside dimensions:  95 mm

Bottom loading design

Bayonet locking, insert and tighten by turning 90°

Self sealing system

Sand or metal powder filtration, 3 cm filling depth

Wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 7.5 ccm/rev

Each spin pump system comprising

                individual drive motor with flange connection to the reduction gear

                hollow gear shaft for installation of spin pump shaft

                shaft with shear pin protection

                reduction ratio:  1:80

                pump speed:  8-30 rev/min

                motor type:  synchronous ac-motor

                rated power:  500w at 50 cps

 

Quench air cabinets bsk 470/1200

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                2 spin finish application nozzles per end

                1 yarn cutter / aspirator unit

                2 spin finish pump

                4 centring yarn guides

                4 pre-intermingling jets

                4 intermingling units

                1 additional operator panel between duo1 and duo 2.

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speedrange:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60

Hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094:

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ± 0.2 mm

Tube outside diameter:  106 ± 0.4 mm

Tube length:  225 ± 0.5 mm

 

Compressed air distribution station:

Mobile aspirator guns with hoses

Electrical control equipment

For electrical power

                general : 3 x 380v/50hz plus ground wire

Euro-standard: 3x400v 50 or 60hz plus ground wire

Maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation: ±2%

 

Process control system (cif):

Fully integrated control system to control and monitor the entire spinning line.

The central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control:

Spinning section.

Speed adjustment for the extruder motor is done via a dc-convertor.

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor.

While current flows, a voltage is inducted into the rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

HOURLY PRODUCTION:

FOR 150 DENIER @ 3500 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 3.5 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 14 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 28 KG/HOUR AND M39 = 56 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 28 KG/HOUR EACH.

(AS PER OUR PEOPLE AT THE EXTRUSION PLANT, THEY WERE RUNNING TRIALS TO PRODUCE THE 150 DENIER @ 4000 MPM WINDER SPEED)

 

FOR 300 DENIER @ 3600 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 7.2 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 28.8 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 57.6 KG/HOUR AND M39 = 115.2 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 57.6 KG/HOUR EACH.

 

FOR 600 DENIER @ 2200 MPM WINDER SPEED, (SPEED LIMITATION DUE TO EXTRUDER CAPACITY) THE HOURLY PRODUCTION IS 8.8 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 35.2 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 70.4 KG/HOUR AND M39 = 140.8 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 70.4 KG/HOUR EACH.

 

MACHINE HAS BEEN PARTIALLY DISASSEMBLED (EXTRUDERS AND SPINBEAMS HAVE BEEN TAKEN DOWN TO GROUNDFLOOR) REST OF THE EQUIPMENT STILL TO BE DISASSEMBLED

Learn More

REFERENCE NUMBER: M-5393 (2206YBJL1UM) L TUFTCO COATING LINE WITH FOAM MACHINE AND SLITTING OPERATION TUFTO COATING LINE FOR EMBOSSED UNITARY BACKED RUGS USING WASHABLE LATEX FOR EMBOSSED WASHABLE RUGS – SET UP FOR 12’ WIDTH AND INCLUDES THE FOLLOWING: TISI MODEL 38500 BUTT SEAMER WITH TRIMMER ON RAIL ENTRANCE J-BOX VERTICAL KEYON PIN TENTER DIRECT COAT APPLICATOR, ROLL OVER ROLL WITH TRAVERSING SYSTEM DAY TANK TO FEED LATEX TO FROTH MACHINE EASE TYPE FROTH MACHINE PRE-STEAMER BANK OF ELECTRIC INFRAREDS TWO BASKET-WEAVE EMBOSSING ROLLERS FOR 12’ WIDTHS FOUR MODULE NATURAL GAS HEATED TUFTCO CURING OVEN COOL OUT SECTION SLITTING SECTION WITH EIGHT SLITTING HEADS AND A CAMERA GUIDING SYSTEM 10 LOOP ACCUMULATOR ROLLUP ELECTRICAL CONTROL SYSTEM BY TUFTCO SPEED RANGE: LINE SPEED FOR COATING 50 OUNCE/SQUARE YARD FACE WEIGHT WITH 24 OZ/SQUARE YARD OF EMBOSSIBLE LATEX IS 35FPM, LINE SPEED FOR COATING 30 OZ/SQUARE YARD FACE WEIGHT WITH 20 OZ/SQUARE YARD OF EMBOSSIBLE LATEX IS 45 FPM. TOILET SEAT CONVERS ARE COATED WITH APPROXIMATELY 7 OZ/SQUARE YARD AT 70 FPM. NOTE THE MAXIMUM MECHANICAL SPEED OF THE COATING LINE IS 70 FPM. QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-5301 (1313THWKXX12) L VAMATEX TERRY TOWEL WEAVING FACTORY YEAR 1995-2003 TERRY TOWEL FACTORY WEAVING DEPARTMENT VAMATEX 1151 ES 3600mm WORKING WIDTH, WITH DOBBY (3) X YEAR 1996 (1) X YEAR 2000 (2) X YEAR 1999 (2) X YEAR 1997 (2) X YEAR 1995 5 SETS WITH 16 HEALD FRAMES, 20 SHAFTS 5 SETS WITH 12 HEALD FRAMES, 16 SHAFTS FACTORY ONCE SELLS WHOLE WITH DOBBY LOT AS ABOVE THEN THEY WILL SELL LOOMS WITH JACQUARDS (6) X VAMATEX LEONARDO YEAR 2003 WITH JACQUARDS J5 STAUBLI 2688 JACQUARD WORKING WIDTH 2600mm (4) X VAMATEX LEONARDO YEAR 2003 WITH VRT SYSTEM/JACQUARD J5 STAUBLI 2688 JACQUARD WORKING WIDTH 2600mm (4) X VAMATEX LEONARDO YEAR 2003 WITH JUMBO JACQUARD J5 STAUBLI 6144 JACQUARD WORKING WIDTH 2600mm (2) X VAMATEX LEONARDO YEAR 2003 WITH GROSS JACQUARD 6144 JACQUARD WORKING WIDTH 2600mm TOTAL QUANTITY: 26 LOOMS Learn More

M-6053 SPUNBOND PRODUCTION LINE, WORKING WIDTH 4040mm TO 4500mm

OFFER 001
SPUNBOND PRODUCTION LINE
WORKING WIDTH: 4040mm
WEIGHT: 130 TO 250 G/M2

OFFER 002
POLYMER CLEANING GROUP

OFFER 003
CRYSTALLIZING GROUP

OFFER 004
DRYING GROUP

OFFER 005
PNEUMATIC CONVEYING SYSTEM

OFFER 006
EXTRUDER HOPPER

OFFER 007
EXTRUDER

OFFER 008
FILTERING UNIT

OFFER 009
MELT TRANSFER LINE

OFFER 010
SPINNING BEAM

OFFER 011
SPINNING PACKS

OFFER 012
FILAMENTS QUENCHING SYSTEM

OFFER 013
FILAMENTS DRAWING AND DISTRIBUTION SYSTEM

OFFER 014
WEB FORMING CONVEYOR BELT

OFFER 015
CREEL FOR APPLICATION OF REINFORCING FILAMENTS

OFFER 016
PRE-NEEDLING MACHINE

OFFER 017
NEEDLING MACHINE

OFFER 018
THERMOSETTING UNIT

OFFER 019
OUTLET CALENDER

OFFER 020
FOULARD

OFFER 021
BINDER PREPARATION SYSTEM

OFFER 022
DRYER

OFFER 023
OUTLET CALENDER

OFFER 024
AUTOMATIC WINDER

OFFER 025
AIR COMPRESSORS (FOR FILAMENTS STRETCHING EJECTORS)

OFFER 026
DIATHERMIC OIL HEATING SYSTEM

OFFER 027
CHILLED WATER CIRCULATION AND GENERATION SYSTEM

OFFER 028
EQUIPMENT FOR CLEANING CYCLE, SPECIAL TOOLS

OFFER 029
FIBRE DUST RECOVERY SYSTEM

OFFER 030
EDGES RECOVERY SYSTEM

OFFER 031
SPINNING SECTION STEEL STRUCTURE

OFFER 032
DISTRIBUTION ELECTRIC CABINETS

OFFER 033
PROCESS ELECTRIC SYSTEM OF EXISTING MACHINES ACCORDING TO THE ACTUAL LAYOUT

OFFER 034
CABLES AND CABLING MATERIALS

QUANTITY: 1 LINE

Learn More