Search results for: 'A-12'
- TT-1209 RIETER UNIFLOC MODEL A11, WORKING WIDTH 2300mm, YEAR 2012TT-1209 RIETER UNIFLOC MODEL A11, WORKING WIDTH 2300mm, YEAR 2012 CONDITION: VERY GOOD QUANTITY: 1 Learn More
- V-1205 RIETER B50 CLEANER WITH FEED TRUNK AND CONDENSER (COTTON) BLOW ROOMREFERENCE NUMBER: V-1205 RIETER B50 CLEANER WITH FEED TRUNK AND CONDENSER (COTTON) BLOW ROOM MAKE: RIETER MODEL: B50 MACHINE TYPE: CLEANER WITH FEED TRUNK AND CONDENSER (COTTON) YEAR: 1994 QUANTITY: 6 GRID BARF: SEGMENT FEED TRUNK - CHUTE: AVAILABLE CONDENSOR: AVAILABLE 2 X WITH PIN TYPE 4 X WITH SAWTOOTH QUANTITY AVAILABLE: 1 Learn More
- TT-1232 RIETER DRAW FRAMES, YEAR 1992 TO 1997TT-1232 RIETER DRAW FRAMES, YEAR 1992 TO 1997 ITEM 001 RIETER DRAW FRAMES TYPE SB 851 QUANTITY: 6 ITEM 002 RIETER DRAW FRAMES TYPE SB51 - 30” CAN Ø QUANTITY: 3 ITEM 003 RIETER DRAW FRAMES TYPE RSB51 - 30” CAN Ø QUANTITY: 1 ITEM 004 RIETER DRAW FRAMES TYPE RSB851 - 450mm CAN Ø QUANTITY: 10 ITEM 005 RIETER DRAW FRAMES TYPE RSB951 - 450mm CAN Ø QUANTITY: 7 ITEM 006 RIETER DRAW FRAMES TYPE SB951 - 450mm CAN Ø QUANTITY: 1 ITEM 007 RIETER DRAW FRAMES TYPE RSB851 - 450mm CAN Ø QUANTITY: 6 ITEM 008 RIETER DRAW FRAMES TYPE SB51 - 450mm CAN Ø QUANTITY: 2 ITEM 009 RIETER DRAW FRAMES TYPE SB51 - 36” CAN Ø QUANTITY: 1 Learn More
- TT-4369 RIETER C-51 CARDS, 1000 X 1200 CANS, YEAR 1998 TO 2004TT-4369 RIETER C-51 CARDS, 1000 X 1200 CANS, YEAR 1998 TO 2004 ITEM 001 RIETER HI-PER C-51 CARD QUANTITY: 1 ITEM 002 RIETER C-51 CARD QUANTITY: 1 Learn More
- C-5163 TRÜTZSCHLER SPINNING MILL BLOW ROOM & RIETER BLOW ROOM
C-5163 SPINNING MILL BLOW ROOM TRÜTZSCHLER & BLOW ROOM RIETER
ITEM 001
CONDENSER LVSA-375
YEAR: 1997
QUANTITY: 1
ITEM 002
MULTIMIXER MCM 6 /1200
YEAR 1997
CVT-4 / 1200
YEAR: 1997
QUANTITY: 1
ITEM 003
JOSSI THE VISION SHIELD FIBER DETECTOR EA-33-S
YEAR: 2002
QUANTITY: 1
ITEM 004
DUSTEX DX 385
YEAR: 1997
QUANTITY: 1
ITEM 005
JOSSI THE SHIELD HIGH PERFORMANCE FIRE DETECTOR
TYPE D-11-250
YEAR: 2005
QUANTITY: 1
ITEM 006
TRÜTZSCHLER FAN
QUANTITY: 3
ITEM 007
MRO METAL DETECTOR
QUANTITY: 1
BLOW ROOM RIETER
ITEM 008
UNIFLOC A 1/2
LENGTH USEFUL 20M
YEAR: 1991
QUANTITY: 1
ITEM 009
FINE OPENER FOR WASTE
WIDTH 0.80M
MODEL: B 3/4S
YEAR: 1991 + APRON 4M
QUANTITY: 1ITEM 010
MONOTAMBOR B 4/1
YEAR: 1991
QUANTITY: 1
ITEM 011
UNIMIX B 7/3R
YEAR: 1991 (OPENER)
QUANTITY: 1
ITEM 012
ERM B 5/5
YEAR: 1989
QUANTITY: 2
ITEM 013
JOSSI FIRE DETECTOR D-11-250
YEAR: 2005
QUANTITY: 1ITEM 014
JOSSI THE VISION SHIELD DETECTOR
FIBER DETECTOR TYPE EA-33-S
YEAR: 2002
QUANTITY: 1
ITEM 015
CARDS TRÜTZSCHLER DK-803
YEAR: 1997
COILER KH 950-1200
AUTOMATIC REVOLVER
FEEDING FBK-533
QUANTITY: 3
ITEM 016
CARDS TRÜTZSCHLER DK-903
YEAR: 2003
1 COILER KH 600-1200
2 COILER KH 450-1200
AUTOMATIC REVOLVER
FEEDING DKF
QUANTITY: 3
ITEM 017
DRAW FRAME TRÜTZSCHLER HSR-1000
YEAR: 2003
DELIVERY 18” (450X1000)
CREEL 8 CANS
SLIVER MONITOR
AUTOLEVELLER
QUANTITY: 2
ITEM 018
ROVING FRAME SIMPLEX ZINZER 670
YEAR: 2003
DRAFT PK 1500
120 SPINDLES
CAPACITY BOBBIN 16”X6”
DRIVER CREEL
COLLECTIVE ASPIRATION
INDIVIDUAL BLOWER ELECTRO-JET
QUANTITY: 2
ITEM 019
AUTOMATIC TRANSPORT INSTALLATION FOR BOBBINS ELECTRO-JET
YEAR: 2003
FOR 8 RING SPINNING FRAME
1,200 SPINDLES
QUANTITY: 2
ITEM 020
INSTALLATION LTG
YEAR: 2003
5 PARTS
WASTE COLLECTING
AIR SYSTEM
QUANTITY: 1
ITEM 021
INSTALLATION LTG
YEAR: 2003
3 PARTS
WASTE COLLECTING
AIR SYSTEM
QUANTITY: 1
ITEM 022
INSTALLATION LTG
YEAR: 2003
5 PARTS
WASTE COLLECTING
CARDING FILTRATION
QUANTITY: 1
ITEM 023
RING SPINNING FRAME ZINZER RM 351
YEAR: 2002 (4)
YEAR: 2003 (1)
1200 SPINDLES
GAUGE 70MM
DRAFT PK 2500
RING 42MM
TUBE 220MM
COWEMAT
COLLECTIVE ASPIRATION
INDIVIDUAL BLOWER
ELECTRO-JET WITH AUTOMATIC UNLOADING
TOTAL LENGTH 47M
QUANTITY: 5
ITEM 024
WINDER SCHLAFHORST 338 RM
YEAR: 2003
COLOR WHITE
60 POSITIONS
MAGAZINE FEEDING 6 TUBES
2 ROBOTS
WAXING
AUTOMATIC CONE CHANGE
TK-840
CLEARER LOEPFE
DELIVERY 4.20 X 6”
INDIVIDUAL BLOWER
QUANTITY: 2
ITEM 025
AUTOCORO SCHLAFHORST SE-11 ACO-288
YEAR: 2001
216 ROTORS
INFORMATOR
DELIVERY CYLINDRICAL SLUBIER PINTER
ROTOR Ø 28-36-40MM
ROLLERS B-174
CLEARERS COROLAB
WAXING
2 ROBOTS CONE CHANGE ROBOTS PIECERS
QUANTITY: 1
ITEM 026
AUTOCORO SCHLAFHORST SE-9
YEAR: 1998
216 ROTORS
2 ROBOTS
WAXING
COROLAB
INFORMATOR
QUANTITY: 1ITEM 027
Learn More
POWER 380V/50HZ
SPLIT SALE POSSIBLE
CONDITION COMPLETED
UNIT PRICE EX-WORKS EURO - G-0784 RIETER FDY EXTRUSION EQUIPMENT FOR POLYPROPYLENE YEAR 1996/98
REFERENCE NUMBER: G-0784
RIETER FDY EXTRUSION EQUIPMENT FOR POLYPROPYLENE YEAR 1996/98
1. Machine m26/39:
Year 1996
For 1 fdy spinning line with 2+4 positions, each position with 4 ends
Product: fdy-yarn on bobbins
Raw material: pp, dried filament grade chips
Yarn count range: 150 – 400 dtex
Winder speed for target: 4000 m/min
Machine technical data:
Position gauge: 800 mm
Spinning pump capacity: 4x10 ccm/rev
Spinneret size diameter: 95 mm
Quench width: 670 mm
Quench length: 1700 mm
Number of spin-finish pumps per position: 1
Capacity of spin-finish pump: 4x0.05 ccm/rev
Number of winders/position: 1
Type of winder: riemat a6-094
Number of packages/winder: 4
Maximum package diameter: 420 mm
Package stroke: 190 mm
Package weight at 280 mm package diameter: approx. 6.2 kg
Detailed technical specifications:
Extruder for 4 positions Year 1998:
1 extruder type e1. 105-30m:
-nominal extruder capacity: max 275 kg/h for pp
-operational extruder capacity: max 248 kg/h for pp
-screw diameter: 105 mm
-l/d ratio: 30
-barrel with:
electrical ceramic heaters
7 heating zones, each zone equipped with one 2xpt100
heating zone capacity approx. 58 kw
inlet zone, water cooled
nozzle for nitrogen purge
insulation
-screw with torpedo mixing head
-reduction gear, including belt transmission to motor
-dc motor, rated power approx. 95kw
-extruder frame
1 extruder measuring head, dowtherm vapour heated
-measuring head comprising:
coarse filter
insulation
-double pt100, one each for melt and dowtherm vapour temperature
-pressure sensors for melt pressure, one in front and one behind the coarse filter
1 melt distribution system, dowtherm vapour heated
-melt distribution system comprising
main product pipe between extruder, measuring head and melt distributor.
Extruder for 2 positions Year 1998:
1 extruder type e1. 60-30
-nominal extruder capacity: max 275 kg/h for pp
-operational extruder capacity: max 248 kg/h for pp
-screw diameter: 60 mm
-l/d ratio: 30
-barrel with
electrical ceramic heaters
6 heating zones, each zone equipped with one 2xpt100
heating zone capacity approx. 17 kw
inlet zone, water cooled
insulation
-screw nitrited with maddock mixing head
-reduction gear, including belt transmission to motor
-dc motor, rated power approx. 22kw
-extruder frame
1 extruder measuring head, electrically heated year 1998
-measuring head comprising:
insulation
Double pt100, one each for melt and dowtherm vapour temperature
pressure sensors for melt pressure
burst disc for power switch-off at overpressure.
1 melt distribution system, dowtherm vapour heated
-melt distribution system comprising
main product pipe between extruder, measuring head and melt distributor.
1 riebeam bottom loading spinning beam year 1998
-beam comprising:
welded-in pump blocks with bolted pump adapter plate
silumin insulation blocks
melt distribution pipes with polished inner surfaces
efficient vapour heating on all sides of spin pumps
optimized heat condustion to the spinnerets
1 freezing valve upstream of each spinpump
2 pressure sensors for measuring the melt pressure in front and behind the spinpump
(2 per line)
heating box, completely insulated
heating by dowtherm vapour
1 double pt100 for measuring and controlling the heating box temperature
Designed as follows:
-bottom loading of rieter quickfit spinpacks
-design temperature 320°c
-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket
Dowtherm evaporator and components for heating system:
-electrically heated, total capacity approx 25 kw
-shut-off valves
-drainage valves
-dry protection sensor
-magnetic controlled level gauge
- vent system on top of measuring head.
Poy spin packs, type rieter quickfit:
-max pressure in the spinpack: 350 bar
-design temperature: 320 °c
-spinneret outside dimensions: 95 mm
-bottom loading design
-bayonet locking, insert and tighten by turning 90°
-self sealing system
-sand or metal powder filtration, 3 cm filling depth
-wire mesh filters
Spin pumps with motors and gears:
Gear pumps, 4-fold
Capacity 4 x 6 ccm/rev
Each spin pump system comprising
Individual drive motor with flange connection to the reduction gear
Hollow gear shaft for installation of spin pump shaft
Shaft with shear pin protection
Reduction ratio 1:80
Pump speed: 8-30 rev/min
Motor type: synchronous ac-motor
Rated power: 500w at 50 cps
Quench air cabinets bsk 670/1700:
Each cabinet comprising:
-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal
-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.
-1 perforated hinged door
-air inlet duct flanged with counter flange, comprising air flow regulating flaps
-interfloor filament duct, length 2000 mm
-alu chutes for start-up
-nozzles for connection of differential pressure gauge.
Spinning vapour exhausts:
-exhaust hood per spinning position for removal of spinning vapour
-hood designed as follows:
made from stainless steel
air flow regulation flap
hood removable for cleaning
Take-up frames, type riedraw 1:
Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.
Per position:
4 inlet yarn guides
4 spin finish application nozzles
1 yarn cutter / aspirator unit
1 spin finish pump
4 centring yarn guides
4 intermingling units
rolls as described further
1 automatic winder riemat a6-094
Drawrolls year 1998:
Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40
Speed range: 750 to 4000 mpm
Roll diameter: 190 mm
Working width: 250 mm
Temperature range: 45-250°c
And 1 bearing separator roll, type srd60 hard chromium plated
Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40
Speedrange: 1000 to 6000 mpm
Roll diameter: 190 mm
Working width: 250 mm
Temperature range: 45-250°c
Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40
Speedrange: 1000 to 6000 mpm
Roll diameter: 190 mm
Working width: 250 mm
Temperature range: 45-250°c
Duo 3 with 2 cold draw roll units each type j7/45-55
Speedrange: 1800 to 5500 mpm
Roll diameter: 150 mm
Working width: 180 mm
Automatic and wasteless winder riemat a6-094
Spindle driven
Number of ends per winder: 4 ends
Yarn count range: 15 to 1000 dtex
Take up speed: 2500 to 5500 m/min
Chuck length: 900 mm
190 mm stroke, 420 mm outside package diameter
Package volume: 24.7 dm³
Tube bore: 94 ±0.2 mm
Tube outside diameter: 106 ±0.4 mm
Tube length: 225 ±0.5 mm
Oil-mist lubrication unit:
Compressed air distribution station
Mobile aspirator guns with hoses
Electrical control equipment
-for electrical power
general: 3 x 380v/50hz plus ground wire
euro-standard: 3x400v 50 or 60hz plus ground wire
maximum voltage variation ±10% measured at terminals of cabinets
maximum frequency variation: ±2%
Process control system (cif):
fully integrated control system to control and monitor the entire spinning line.
the central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.
Drive and heater control year 1998:
Spinning section:
Speed adjustment for the extruder motor is done via a dc-convertor
To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.
The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.
One common frequency inverter supplies the synchronous ac motors for the spin pumps.
According to process conditions, the plc transmits the setpoint to the inverter.
All motors are equipped with an overload protection.
Solid state relays heat each extruder zone and spinning beam.
Each extruder zone and the spinning beam represent an independent control loop.
Take-up section:
The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.
All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.
Heating system:
The heating unit rhu is processor-controlled.
The power supply is taken straight from 3-phase 380/400v which powers the cabinet.
The inductor is fitted inside the draw roll.
The rhu switches the current on and off in this inductor. While current flows, a voltage is inducted into the
Rotating draw roll.
This sets up a short-circuit current in the draw roll, thereby heating the roll unit.
2. Machines m27/ 28 / 30 year 1998:
For 3 fdy spinning lines each with 2 positions, and each position with 4 ends
Product: fdy-yarn on bobbins
Raw material: pp, dried filament grade chips
Yarn count range: 150 – 400 dtex
Winder speed for target: 4000 m/min
Machine technical data:
Position gauge: 1000 mm
Spinning pump capacity: 4x7.5 ccm/rev
Spinneret size diameter: 95 mm
Quench width: 470 mm
Quench length: 1200 mm
Number of spin-finish pumps per position: 2
Capacity of spin-finish pump: 4x0.16 ccm/rev + 4x0,05 ccm/rev
Number of winders/position: 1
Type of winder: riemat a6-094
Number of packages/winder: 4
Maximum package diameter: 420 mm
Package stroke: 190 mm
Package weight at 280 mm package diameter: approx. 6.2 kg
Detailed technical specifications:
1 extruder type e1. 60-30m
-nominal extruder capacity: max 80 kg/h for pp
-screw diameter: 65 mm
-l/d ratio: 30
-barrel with:
electrical ceramic heaters
7 heating zones, each zone equipped with one 2xpt100
heating zone capacity approx. 22 kw
inlet zone, water cooled
nozzle for nitrogen purge
insulation
-screw with torpedo mixing head
-reduction gear, including belt transmission to motor
-dc motor, rated power approx. 22kw
-extruder frame
1 extruder measuring head, electrically heated:
-measuring head comprising:
coarse filter
insulation
-double pt100, one each for melt and dowtherm vapour temperature
-pressure sensors for melt pressure, one in front and one behind the coarse filter
1 melt distribution system, dowtherm vapour heated:
Melt distribution system comprising:
main product pipe between extruder, measuring head and melt distributor.
1 riebeam bottom loading spinning beam:
-beam comprising:
welded-in pump blocks with bolted pump adapter plate
silumin insulation blocks
melt distribution pipes with polished inner surfaces
efficient vapour heating on all sides of spin pumps
optimized heat condustion to the spinnerets
1 freezing valve upstream of each spinpump
2 pressure sensors for measuring the melt pressure in front and behind the spinpump
(2 per line)
heating box, completely insulated
heating by dowtherm vapour
1 double pt100 for measuring and controlling the heating box temperature
Designed as follows:
-bottom loading of rieter quickfit spinpacks
-design temperature 320°c
-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket
Dowtherm evaporator and components for heating system:
-electrically heated, total capacity approx 18 kw
-shut-off valves
-drainage valves
-dry protection sensor
-magnetic controlled
-level gauge
-vent system on top of measuring head.
Poy spin packs, type rieter quickfit:
Max pressure in the spinpack: 350 bar
Design temperature: 320 °c
Spinneret outside dimensions: 95 mm
Bottom loading design
Bayonet locking, insert and tighten by turning 90°
Self sealing system
Sand or metal powder filtration, 3 cm filling depth
Wire mesh filters
Spin pumps with motors and gears:
Gear pumps, 4-fold
Capacity 4 x 7.5 ccm/rev
Each spin pump system comprising
individual drive motor with flange connection to the reduction gear
hollow gear shaft for installation of spin pump shaft
shaft with shear pin protection
reduction ratio: 1:80
pump speed: 8-30 rev/min
motor type: synchronous ac-motor
rated power: 500w at 50 cps
Quench air cabinets bsk 470/1200
Each cabinet comprising:
-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal
-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.
-1 perforated hinged door
-air inlet duct flanged with counter flange, comprising air flow regulating flaps
-interfloor filament duct, length 2000 mm
-alu chutes for start-up
-nozzles for connection of differential pressure gauge.
Spinning vapour exhausts:
-exhaust hood per spinning position for removal of spinning vapour
-hood designed as follows:
made from stainless steel
air flow regulation flap
hood removable for cleaning
Take-up frames, type riedraw 1:
Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.
Per position:
4 inlet yarn guides
2 spin finish application nozzles per end
1 yarn cutter / aspirator unit
2 spin finish pump
4 centring yarn guides
4 pre-intermingling jets
4 intermingling units
1 additional operator panel between duo1 and duo 2.
rolls as described further
1 automatic winder riemat a6-094
Drawrolls:
Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40
Speedrange: 750 to 4000 mpm
Roll diameter: 190 mm
Working width: 250 mm
Temperature range: 45-250°c
And 1 bearing separator roll, type srd60
Hard chromium plated
Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40
Speedrange: 1000 to 6000 mpm
Roll diameter: 190 mm
Working width: 250 mm
Temperature range: 45-250°c
Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40
Speedrange: 1000 to 6000 mpm
Roll diameter: 190 mm
Working width: 250 mm
Temperature range: 45-250°c
Duo 3 with 2 cold draw roll units each type j7/45-55
Speedrange: 1800 to 5500 mpm
Roll diameter: 150 mm
Working width: 180 mm
Automatic and wasteless winder riemat a6-094:
Spindle driven
Number of ends per winder: 4 ends
Yarn count range: 15 to 1000 dtex
Take up speed: 2500 to 5500 m/min
Chuck length: 900 mm
190 mm stroke, 420 mm outside package diameter
Package volume: 24.7 dm³
Tube bore: 94 ± 0.2 mm
Tube outside diameter: 106 ± 0.4 mm
Tube length: 225 ± 0.5 mm
Compressed air distribution station:
Mobile aspirator guns with hoses
Electrical control equipment
For electrical power
general : 3 x 380v/50hz plus ground wire
Euro-standard: 3x400v 50 or 60hz plus ground wire
Maximum voltage variation ±10% measured at terminals of cabinets
maximum frequency variation: ±2%
Process control system (cif):
Fully integrated control system to control and monitor the entire spinning line.
The central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.
Drive and heater control:
Spinning section.
Speed adjustment for the extruder motor is done via a dc-convertor.
To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.
The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.
One common frequency inverter supplies the synchronous ac motors for the spin pumps.
According to process conditions, the plc transmits the setpoint to the inverter.
All motors are equipped with an overload protection.
Solid state relays heat each extruder zone and spinning beam.
Each extruder zone and the spinning beam represent an independent control loop.
Take-up section:
The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.
All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.
Heating system:
The heating unit rhu is processor-controlled.
The power supply is taken straight from 3-phase 380/400v which powers the cabinet.
The inductor is fitted inside the draw roll.
The rhu switches the current on and off in this inductor.
While current flows, a voltage is inducted into the rotating draw roll.
This sets up a short-circuit current in the draw roll, thereby heating the roll unit.
HOURLY PRODUCTION:
FOR 150 DENIER @ 3500 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 3.5 KG/BOBBIN.
AS THERE IS 4 ENDS PER POSITION, THIS MEANS 14 KG/HOUR/POSITION
M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 28 KG/HOUR AND M39 = 56 KG/HOUR
M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 28 KG/HOUR EACH.
(AS PER OUR PEOPLE AT THE EXTRUSION PLANT, THEY WERE RUNNING TRIALS TO PRODUCE THE 150 DENIER @ 4000 MPM WINDER SPEED)
FOR 300 DENIER @ 3600 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 7.2 KG/BOBBIN.
AS THERE IS 4 ENDS PER POSITION, THIS MEANS 28.8 KG/HOUR/POSITION
M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 57.6 KG/HOUR AND M39 = 115.2 KG/HOUR
M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 57.6 KG/HOUR EACH.
FOR 600 DENIER @ 2200 MPM WINDER SPEED, (SPEED LIMITATION DUE TO EXTRUDER CAPACITY) THE HOURLY PRODUCTION IS 8.8 KG/BOBBIN.
AS THERE IS 4 ENDS PER POSITION, THIS MEANS 35.2 KG/HOUR/POSITION
M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 70.4 KG/HOUR AND M39 = 140.8 KG/HOUR
M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 70.4 KG/HOUR EACH.
MACHINE HAS BEEN PARTIALLY DISASSEMBLED (EXTRUDERS AND SPINBEAMS HAVE BEEN TAKEN DOWN TO GROUNDFLOOR) REST OF THE EQUIPMENT STILL TO BE DISASSEMBLED
Learn More - TT-4532 RIETER OPEN END PLANT, 2400 ROTORS, YEAR 2006 TO 2010TT-4532 RIETER OPEN END PLANT, 2400 ROTORS, YEAR 2006 TO 2010 THE PLANT STOPPED IN DECEMBER 2023 ELECTRICAL ENERGY 700 KW INSTALLED Learn More
- TT-3392 RIETER CARDING MACHINES TYPE C-60, CAN SIZE 1000 X 1200mm, YEAR 2004TT-3392 RIETER CARDING MACHINES TYPE C-60, CAN SIZE 1000 X 1200mm, YEAR 2004 RIETER CARDING MACHINES TYPE C-60 YEAR 2004 QUANTITY: 6 Learn More
- TT-2155 RIETER COMPLETE SPINNING PLANT WITH 16,128 SPINDLES, YEAR 1991 TO 1995TT-2155 RIETER COMPLETE SPINNING PLANT WITH 16,128 SPINDLES, YEAR 1991 TO 1995 RIETER COMPLETE SPINNING PLANT 16,128 SPINDLES YEAR 1991 TO 1995 QUANTITY: 1 PLANT Learn More
- C-2556 RIETER G33 RINGFRAME LINKED TO SAVIO ORION I WINDER WITH 1200 SPINDLES, YEAR 2000REFERENCE NUMBER: C-2556 RIETER G33 RINGFRAME LINKED TO SAVIO ORION I WINDER WITH 1200 SPINDLES, YEAR 2000 DETAILS: SUITABLE FOR RING DENIM RIETER G33 RINGFRAME YEAR: 2000 NUMBER OF SPINDLES: 1200 SPINDLE GAUGE: 75mm LINKED TO: SAVIO ORION I WINDER YEAR: 2000 NUMBER OF DRUMS: 24 QUANTITY AVAILABLE: 18 Learn More