Search results for: 'press'

REFERENCE NUMBER: M-1487 (660125KJH5RXM) CONTINUOUS WASHING LINE IN OPEN WIDTH FOR WOVEN FABRIC YEAR 2000 WIDTH 3600mm CONTINUOUS WASHING LINE IN OPEN WIDTH FOR WOVEN FABRIC MEZZERA BIANCO ROLLERS WIDTH: 3800 mm WORKING WIDTH: 3600 mm YEAR OF CONSTRUCTION: 2000 COMPOSED OF: - DOUBLE INTRODUCTION, FRAME MANUFACTURED IN PAINTED FE PROFILES , SLINGING BY ADJUSTABLE FLYWHEELS, 2 GROUPS OF WIDENING-CENTRING ROLLERS E+L KF20, FABRIC GUIDING ROLLERS IN AISI 316, DRAGGING CALANDER WITH 3 ROLLERS. - BY-PASS AND SYNCHRONIZATION BRIDGE COMPOSED OF : FRAME IN CARBON STEEL FE37, GROUP OF GUIDING ROLLERS IN STAINLESS STEEL COMPLETE WITH SELF-ALIGNED BEARINGS TO GUIDE THE FABRIC TO THE FOLLOWING SECTION . - ROLLER WASHING UNIT IN OPEN WIDTH , MOD. ACTIVA 30, WITH DOUBLE FABRIC DWELLING. - 5 INTERMEDIATE SQUEEZERS - SLAT WIDENING UNIT FOR DOUBLE ROW - SQUEEZING SYSTEM WITH : 2 ROLLERS COATED RUBBER/EBONITE, RUBBER HARDNESS 75-80 SHA, WORKING PRESSURE 3000 KG, A.C. MOTOR GEARBOX, INVERTER, PNEUMATIC DRIVE. - ROLLER WASHING UNIT IN OPEN WIDTH , MOD. ACTIVA 30, WITH DOUBLE FABRIC DWELLING. - 5 INTERMEDIATE SQUEEZERS - SLAT WIDENING UNIT FOR DOUBLE ROW - SQUEEZING SYSTEM WITH : 2 ROLLERS COATED RUBBER/EBONITE, RUBBER HARDNESS 75-80 SHA, WORKING PRESSURE 3000 KG, A.C. MOTOR GEARBOX, INVERTER, PNEUMATIC DRIVE. - ROLLER WASHING UNIT IN OPEN WIDTH, MOD. ACTIVA 20, WITH SIMPLE FABRIC DWELLING - INTERMEDIATE SEPARATOR FOR TANK SPLITTING - 5 INTERMEDIATE SQUEEZERS - SLAT WIDENING UNIT FOR DOUBLE ROW - DELIVERY GROUP WITH PNEUMATIC FOULARD OF 10 TON RUBBER/EBONITE, COMPLETE WITH BEARING FRAME AND PROTECTION CASING. RUBBER ROLLER WITH HIGH SQUEEZING EFFECT ROLLIN - SECOND DISCHARGING STACK - PUMP FOR THE BATH RECYCLING IN THE NEUTRALIZATION PART - PH-METER WITH DOSING PUMP TO NEUTRALIZE IN THE FIRST SECTION OF THE LAST TANK - BIG BATCHER, ADHERING TYPE, DRIVEN BY MOTOR WITH VARIABLE SPEED. - SLAT WIDENING UNIT FOR DOUBLE ROW - 2 DUCTING FOR THE WATER RECOVERY BETWEEN THE 2 WASHING UNITS IN OPEN WIDTH - 3 TEMPERATURE AUTOMATIC CONTROLS PER EACH WASHING UNIT - 4 SETS OF PROPORTIONAL VALVES WITH LITER COUNTER - COMPLETE MOTORIZATION OF THE LINE WITH MOTORS GROUP, ELECTRIC CONTROL CABINET AND SYNOPTICAL PANEL. - VERTICAL DRYER RAMALLUMIN COMPOSED OF 2 COLUMNS WITH 8 ROLLERS, IN ORDER TO DRY BOTH FACES OF THE FABRIC, FOR A TOTAL OF 16 DRYING ROLLERS. O MAX. WORKING WIDTH: 3600 mm. O MAX. MECHANICAL SPEED: 80 MT./MIN. O MAX. WEIGHT OF THE FABRIC, IN WIDTH 3400 mm 900 GR./LINEAR METER O FORESEEN WORKING SPEED WITH FABRIC W=3400mm W=850 GR. 40/45 MT./MIN. O FORESEEN WORKING SPEED WITH FABRIC W=3400 W=425 GR. 80 MT./MIN. O MODIFIED, AS FOLLOWS, WITH ADDITIONS OF : 2 COOLING ROLLERS, 1 SET OF ACCESSORIES FOR THE FEEDING AND RETURN OF THE COOLING WATER, SET OF COMPONENTS FOR THE CONTROL, 4 RETURN CYLINDERS, COMPENSATING GROUP ON THE INTRODUCTION SIDE, 3 SUCTIONING HOODS, 1 EXHAUSTER. Learn More

REFERENCE NUMBER: M-1943

BELT PUNCHING LINE YEAR 1996 (DYE CUTTER WITH CONVEYOR TRANSPORT)

 

BRAND: HANDSAEME

SIZE: 2250mm X 2000mm – HYDRAULIC POWER OF 150 TONS

PUNCHING IS DONE ON A TRANSPORT BELT.

PUNCHING ADJUSTABLE HEIGTH TILL 200mm

PRESSURE CAN BE ADJUSTED

PRESSURE IS DELIVERED BY A HYDRAULIC GROUP IN CONNECTION WITH A MECHANICAL LEVER 

CAN BE USED ON FOAM

SOME DYES INCLUDED

NEW DYES CAN BE ORDERED

 

IN EXCELLENT CONDITION, USED ONLY OCCASIONALLY

Learn More

REFERENCE NUMBER: M-4089 (990DJSKXX8) L

COMPLETE RIETER RING SPINNING & YARN DYE FACTORY – 37,056 SPINDLES- will sell individually

 

FACTORY WAS PRODUCING VARIOUS SPECIALTY YARNS FOR USE IN APPAREL AND TECHNICAL TEXTILES

ALL RING FRAMES SHORT STAPLE FOR FIBERS UP TO 40mm, 220mm TUBES, APPROXIMATELY HALF OF THE RING FRAMES ARE WITH PINTER CORE DEVICE OR AMSLER SLUBBING DEVICE. AMSLER AND PINTER AVAILABLE TO SELL SEPARATELY.

 

CARDING

COMBERS

ROVING/FLYERS

RING SPINNING

WINDING

TWISTING

COMPLETE YARN DYE HOUSE & DYE LAB

 

QUANTITY AVAILABLE: 1

Learn More

REFERENCE NUMBER: F-1362 PILLOW WEIGHT SETTING VACUUM FILLING MACHINE THE VACUUM FILLING MACHINE IS FOR FABRIC PILLOW AND CUSHION FILLING. SUITABLE MATERIAL IS SILICONIZED STAPLE FIBER. THE VACUUM FILLING MACHINE IS EQUIPPED WITH A FREQUENCY CONVERTER. THE FILLING SPEED IS ADJUSTABLE TO THE FILLING SURFACE IS VERY EVEN. THE FILLING IS CARRIED OUT BY "SUCTION", NOT THE TRADITIONAL "BLOW", WHICH CAN MAKE FILLING MATERIALS GO IN ALL DIRECTIONS AND COME TO THE 4 CORNERS OF THE PILLOW OR CUSHION. THE AFTER-FILLING EFFECT WITH BE BETTER THAN ALL OTHER FILLING. THE LINE CAN SET THE WEIGHT FOR EACH PILLOW/CUSHION APPROXIMATELY. FIBER CARDING MACHINE: DIMENSIONS: 2150 X 900 X 940mm POWER: 4.75kW NET WEIGHT: 600kg FIBER SUCTION AND SILENSOR: DIMENSIONS: 700 X 930 X 2450mm POWER: 7.5kW AIR PRESSURE: 1mpa NET WEIGHT: 300kg VACUUM FILLING MACHINE: DIMENSIONS: 2990 X 1700 X 2450mm AIR PRESSURE: 1mpa NET WEIGHT: 400kg QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: A-1189 (1212GHBXX11) A THIES, TYPE TRD SOFT TRD 140/3, YEAR 2002 THIES TYPE: TRD, SOFT TRD 140/3 YEAR: 2002 MAX WORKING PRESSURE: 0.35 MPA MAX TEST PRESSURE: 0.455 MPA TEMPERATURE: 140°C WATER VOLUME OF 1 TUBE: 1100 LITERS (WHOLE MACHINE 3300 LITERS) AT THE MOMENT : CA 120-140 KG FABRICS IN 1 TUBE BY 100-300 G/SQM IT IS POSSIBLE WORK WITH 2 OR 3 TUBES MACHINE WORKS INSPECTION POSSIBLE ANY TIME QUANTITY: 1 EMAIL US FOR PRICE & PICTURES INCLUDE OUR REFERENCE NUMBER Learn More

REFERENCE NUMBER: M-5012 (1212YBZTXX11) L TMT PF-1593 MULTIPROGRAM AUTOCLAVE DECATIZING MACHINE YEAR 1998 AUTOCLAVE DECATIZING MACHINE MANUFACTURER: TMT MODEL: PF 1593 MULTIPROGRAM YEAR OF CONSTRUCTION: 1998 AUTOCLAVE DIAMETER: 1500mm SATIN CLOTH WIDTH: 1800mm SATIN CLOTH LENGTH STANDARD: 750 TO 1,000 MT. MAXIMUM FABRIC WIDTH: 1600mm POWER INSTALLED: 48 KW POWER USED: 30 KW STEAM PRESSURE: 6 TO 11 BAR COMPRESSED AIR PRESSURE: 6 TO 8 BAR MACHINE IS IN EXCELLENT CONDITION AND IS RUNNING AVAILABLE END OF DECEMBER 2014 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-5054 (1212DYTWXX11) L KLEINEWEFERS DYE PADDER COLD PAD BATCH YEAR 1999 WIDTH 2400mm USED DYE PADDER COLD PAD BATCH (KKV-FOULARD) PRODUCER KLEINEWEFERS KTM, GERMANY TYPE BICOFLEX FQ245 WORKING WIDTH 2400mm YEAR 1999 AIR PRESSURE MAXIMUM 10 BAR WATER PRESSURE MAXIMUM 5 BAR QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-3349 (88013DYN7U)-D TOYOTA AIRJET LOOMS TOYOTA AIR JET LOOM QTY MODEL=JA2S-190TP-T610 TOTAL 60 LOOMS 60 STAUBLI POSITIVE TAPPET CAM MOPTION TYPE 1620 CAM BOX WITH 7 SHAFT 6 CAMS WITH 1 SPACER FOR EACH LOOM 60SETS 1 REPEAT GEAR FOR EACH LOOM 60SETS PROFILE REED SYSTEM REED SPACE 190 CM 60 LOWER BUILT ONE PIECE BOX TYPE SIDE FRAME FOR HIGH SPEED OPERATION 60 OIL BATH LUBRICATION FOR MAIN UNITS 60 TWO SIDES CRANK DRIVE BEATING WITH OIL BATH 60 HIGH TORQE INDUCTION MOTOR WITH SOLENOID BRAKE (4P-3PHASE,3.5KW) 60 MAIN CONTROL COMPUTER WITH 32 BYTES CPU 60 DISTRIBUTED CONTROL SYSTEM BY OPTICAL FIBER COMMUNICATION NETWORK 60 TOUCH SCREEN FUNCTION PANEL WITH MULTI- WINDOW DISPLAY 60 AUTOMATIC INITIAL CONDITION - (ICS) SYSTEM 60 AUTOMATIC FAULT ALRAM FUNCTION 60 WEEKLY EFFICIENCY GRAPH DISPLAY & DOWN TIME 60 CAUSE DISLPAY BEAM CLOTH ESTIMATOR 60 2 COLOUR MIXING DEVICE BY ELECTRIC DRUM POLE (EDP) 60 TAPERED SUB NOZZLE 60 LOW AIR PRESURE & HIGH PROPULSIVE MAIN NOZZLE 60 DIRECT DRIVE SOLENOID VALVE FOR MAIN & SUB NOZZLE 60 TWO INDEPENDENT SUB NOZZLE TANKS 60 TAPERED TUNNEL REED 60 AUTOMATIC TIMING CONTROLLER (ATC) 60 AUTOMATIC BRAKE SYSTEM (ABS) 60 TIMING CHEKER WITH GRAPH DISPLAY ON FUNCTION PANEL 60 CENTRALIZED REGULATOR 60 ELECTRONIC LET OFF MOTION BY DIGITAL AC SERVO MOTOR 60 AUTOMATIC LET OFF ADJUSTMENT 60 FELL FORWARD DEVICE FOR STOP MARK PREVENTION 60 POSITIVE EASING MOTION WITH TWIN BACK ROLLER 60 MECHANICAL TAKE UP MOTION BY CHANGE GEAR 60 ON LOOM TAKE UP MOTION FOR MAXIMUM -600MM CLOTH DIA 60 DOUBLE PRESS CLOTH ROLLS 60LOOM METAL SPRAYED SURFACE TAKE UP ROOLER 60 RING TAMPLE-3ROWS -24RING 60SET ROTARY LENO SELVEDGE AT L+R SIDE WITH ELECTRIC STOP MOTION 60SET DOUBLE FEELER FOR WEFT STOP MOTION -(REFLECTING TYPE ) 60 ELECTRIC WARP STOP MOTION BY SIX LINES CONTACT BAR 6 PER LOOM YARN BEAM SET WITH 1000 MM FLANGE & 178 MM BAREL DIA 90 CLOTH ROLLER 100 MM DIA 90 REED 60PIECE HEALD FRAMES 7 PER LOOM HEALD WIRE (331MML) C TYPE 6000PER LOOM DROPPER- (165-11-0.3) 6000PER LOOM QUANTITY: 60 TOYOTA AIR JET LOOM QTY MODEL=JA2S-280TP-T610 TOTAL 12 LOOM. 12 STAUBLI POSITIVE TAPPET CAM MOPTION 12SETS TYPE 1620 CAM BOX WITH 7 SHAFT 6 CAMS WITH 1 SPACER FOR EACH LOOM 12SETS 1 REPEAT GEAR FOR EACH LOOM 12SETS PROFILE REED SYSTEM REED SPACE 280 CM 12 LOWER BUILT ONE PIECE BOX TYPE SIDE FRAME FOR HIGH SPEED OPERATION 12 OIL BATH LUBRICATION FOR MAIN UNIT 12 TWO SIDES CRANK DRIVE BEATING WITH OIL BATH 12 HIGH TORQE INDUCTION MOTOR WITH SOLENOID 12 BRAKE (4P-3PHASE,3.5KW) MAIN CONTROL COMPUTER WITH 32 BYTES CPU 12 DISTRIBUTED CONTROL SYSTEM BY OPTICAL FIBER 12 COMMUNICATION NETWORK TOUCH SCREEN FUNCTION PANEL WITH MULTI- WINDOW DISPLAY 12 AUTOMATIC INITIAL CONDITION - (ICS) SYSTEM AUTOMATIC FAULT ALRAM FUNCTION 12 WEEKLY EFFICIENCY GRAPH DISPLAY & DOWN TIME 12 CAUSE DISLPAY BEAM CLOTH ESTIMATOR 12 2 COLOUR MIXING DEVICE BY ELECTRIC DRUM POLE (EDP) 12 TAPERED SUB NOZZLE 12 LOW AIR PRESURE & HIGH PROPULSIVE MAIN NOZZLE 12 DIRECT DRIVE SOLENIOD VALVE FOR MAIN & SUB NOZZLE 12 TWO INDEPENDENT SUB NOZZLE TANKS 12 TAPERED TUNNEL REED 12 AUTOMATIC TIMING CONTROL (ATC) 12 AUTOMATIC BRAKE SYSTEM (ABS) 12 TIMING CHEKER WITH GRAPH DISPLAY ON FUNCTION PANEL 12 CENTRALIZED REGULATOR 12 ELECTRONIC LET OFF MOTION BY DIGITAL AC SERVO MOTOR 12 AUTOMATIC LET OFF ADJUSTMENT 12 FELL FORWARD DEVICE FOR STOP MARK PREVENTION 12 POSITIVE EASING MOTION WITH TWIN BACK ROLLER 12 MECHANICAL TAKE UP MOTION BY CHANGE GEAR 12 ON LOOM TAKE UP MOTION FOR MAXIMUM -600MMCLOTH DIA 12 DOUBLE PRESS CLOTH ROLLS 12LOOM METAL SPRAYED SURFASE TAKE UP ROOLER 12 RING TAMPLE-3ROW -30RING 12SET OCCUPIED WITH TUCK IN DEVICE WITH COMPLETE ACCESSORIES DOUBLE FEELER FOR WEFT STOP MOTION -(REFLECTING TYPE ) ELECTRIC WARP STOP MOTION BY SIX LINES CONTACT BAR 6PER LOOM YARN BEAM SET WITH 1000 MM FLANGE & 178 MM BARREL DIA 18 CLOTH ROLLER 100 MM DIA 18 REED 12PIECE HEALD FRAMES 7 PER LOOM HEALD WIRE (331MML) C TYPE 8000PER LOOM DROPPER- (165-11-0.3) 8000PER LOOM QUANTITY AVAILABLE: 12 LOOMS 20 LOOMS HAVE GEAR FOR TUCK IN DEVICE, GEAR BOX AT LEFT SIDE 1 INVERTER FOR 36 LOOMS ( 2 INVERTERS FOR ALL 72) 2 ATLAS COPCO ZR-315 COMPRESORS AND DRYER MD-1000 AVAILALE AT ADDITIONAL COST Learn More

REFERENCE NUMBER: M-4701 (1111DPTVXX10) L RAMISCH RK 360-H CALENDER YEAR 1971 WIDTH 2200mm (RENEWED IN 2008) RAMISCH CALENDER TYPE RK 360 – H (FOR CALENDERING AND COTTON LUSTERING) WORKING WIDTH 2200mm 3 ROLLERS TOTAL WIDTH 2400mm (STEEL/COTTON/STEEL) YEAR 1971 BUT TOTALLY RENEWED IN YEAR 2008 MAXIMUM PRESSURE 160 BARS ON BOTH LATERAL HYDRAULIC CYLINDERS (LEFT AND RIGHT) INVERTER HITACHI SJ 300 TEMPERATURE CONTROL APAR AR650, AR682 METER COUNTER SIMEX SLK-94 METAL DETECTOR CEIA SEAM DETECTION CACCIA ELECTRNICA WITH DOUBLE CONTROLLER STEAM PRESSURE 4 BARS STEAM CONSUMPTION CA 400 KG/H MOTOR POWER: 30 KW QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More