Search results for: 'screen+pr'

REFERENCE NUMBER: T-6552

MASK AIR TIGHTNESS TESTER

 

MASK AIR TIGHTNESS TESTER

HOW TO CHOOSE A HIGH-QUALITY MASK NOT ONLY DEPENDS ON THE FILTERING EFFICIENCY OF THEMASK, BUT ALSO TO CONFIRM WHETHER THE MASK IS COMPLETELY IN CONTACT WITH THE FACE, OTHERWISE AEROSOL PARTICLES SUCH AS GERMS THAT HAVE NOT BEEN FILTERED BY THE MASK WILL BE INHALED FROM THE INADEQUATE ADHESION. THEREFORE, IT IS VERY IMPORTANT TO CHECK THE WEARING STATUS OF THE MASK. THE EUROPEAN AND AMERICAN COUNTRIES HAVE LISTED THE APPLICATION TEST OF THE MASK AS A STRONG INSPECTION ITEM.

FOR EXAMPLE, THE N95 MASK IS ONE OF 9 TYPES OF PARTICULATE PROTECTIVE MASKS CERTIFIED BY NIOSH (NATIONAL INSTITUTE OF OCCUPATIONAL SAFETY AND HEALTH). "N" INDICATES OIL RESISTANCE."95" INDICATES THAT THE PARTICLE CONCENTRATION IN THE MASK IS MORE THAN 95% LOWER THAN THAT OF THE PARTICLES OUTSIDE THE MASK WHEN EXPOSED TO THE SPECIFIED NUMBER OF SPECIAL TEST PARTICLES. N95 IS NOT A SPECIFIC PRODUCT NAME, AS LONG AS IT MEETS THE N95 STANDARD AND PASSES THE NIOSH REVIEW, IT CAN BE CALLED "N95 MASK".

N95 TYPE MASKS, IN ADDITION TO THE FILTERING EFFICIENCY OF THE MASKS, THE CLOSENESS OF THE MASKS TO THE FACE IS ONE OF THE IMPORTANT FACTORS THAT DETERMINE THE EFFECTIVENESS OF THE USE OF THE MASKS. THE SUITABILITY OF DIFFERENT TYPES OF MASKS FOR THE HUMAN FACE VARIES GREATLY.

THEREFORE, BEFORE USING A MASK, THE SUITABILITY OF THE MASK SHOULD BE CHECKED FIRST. DURING THETIGHTNESS TEST OF THE WEARER'S FACE, ENSURE THAT AIR CAN PASS IN AND OUT THROUGH THE MASK WHEN IT IS CLOSE TO THE EDGE OF THE FACE. THE MASK TIGHTNESS TESTER CAN QUICKLY COMPLETE THE TIGHTNESS TEST OF RESPIRATORS SUCH AS MASKS TO ENSURE THAT IT PROVIDES GOOD PROTECTION PERFORMANCE. IT CONFORMS TO THE CHINESE RESPIRATOR STANDARD GB2626-2019 STANDARD, OSHA / CSA STANDARD AND CHINA GENERAL ADMINISTRATION OF QUALITY SUPERVISION, INSPECTION AND QUARANTINE "GB 19083-2010 TECHNICAL REQUIREMENTS FOR MEDICAL PROTECTIVE MASKS" JOINTLY ISSUED BY THE CHINA NATIONAL STANDARDIZATION ADMINISTRATION COMMITTEE.

ADHESION (SUITABILITY TEST): THE MASK DESIGN SHOULD PROVIDE GOOD ADHESION. THE OVERALL FIT FACTOR OF THE MASK SHOULD NOT BE LESS THAN 100. THIS TEST THE REQUIREMENTS WERE FORMALLY IMPLEMENTED ON AUGUST 1, 2011.

Learn More

REFERENCE NUMBER: L-2532
MODEL: 180
1000 TO 2000mm WIDTH

Learn More

REFERENCE NUMBER: R-7904

DEINKING PLANT, CAPACITY 150 TPD

 

QUANTITY: 1

Learn More

C-4227 EREMA RM120TVE FILM/FIBER PELLETIZING LINE, EXTRUDER 120mm, YEAR 2000 - NEW

EREMA PELLETIZING LINE NEW
MODEL: RM120TVE FILM/FIBER
YEAR: 2000
LINE CONSISTS OF THE FOLLOWING:
EREMA MODEL RM120TVE
120mm EXTRUDER WITH 36/1 L/D DOUBLE VENTED BARREL
EXTRUDER IS DRIVEN BY A 160KW AC MOTOR WITH INVERTER
DOUBLE VENT INCLUDES A STAINLESS STEEL DEKER VACUUM PUMP
APPROXIMATELY 50 CUBIC FOOT STAINLESS STEEL CUTTER/COMPACTOR MOUNTED AT FEED SECTION
AND FED BY A 35″ WIDE X 20′ LONG INCLINED BELT CONVEYOR
CUTTER COMPACTOR DRIVEN BY A 105 KW
480 VOLT AC MOTOR

QUANTITY: 1 LINE

Learn More

REFERENCE NUMBER: M-1480

SLITTER REWINDER 1800mm WIDTH AND 1000mm DIAMETER-NEW MACHINE

 

TECHNICAL CHARACTERISTICS:

 

UNWINDER

MAXIMUM WIDTH: 1800mm

MAXIMUM DIAMETER: 1100mm

MINIMUM WIDTH: 420mm

MAXIMUM WEIGHT: 300kgs

CORE ID: 3”

 

REWINDER:

MAXIMUM WIDTH: 1800mm

MAXIMUM DIAMETER: 1000mm

MINIMUM WIDTH: 100mm

MAXIMUM WEIGHT PER SHAFT: 300kgs

CORE ID: 3”

 

MATERIAL:

TYPE: 100% PP NONWOVEN

MINIMUM: 10gsm

MAXIMUM: 150gsm

 

TENSION:

MAXIMUM: 2 PLI

 

SPEED:

METERS PER MINUTE: 250

 

DESCRIPTION:

REWINDER MACHINE FOR NONWOVEN ROLLS: UP TO 1000 mm DIAMETER AT UNWINDER AND 1200 mm AT REWINDER.

THE WORKSTATION OFFERS EASY ACCESS TO THE TENSION CONTROL AREA AS WELL AS THE TRIMMING AREA; THIS WAY, ANY MODIFICATION ON THE MATERIAL MEASUREMENTS CAN BE DONE SAFELY.

THE WORKSTATION WILL DELIVER MODULES OF ROLLED MATERIAL WITH SPECIFIC DENSITY, AND SEPARATED FROM EACH OTHER IN ORDER TO KEEP OPERATION CONDITIONS WITHIN REQUIRED QUALITY CONTROLS.

 

UNWINDER WITH SHAFT:

THERE IS A CENTRAL UNWINDING SYSTEM SUPPORTED BY A 3” STEEL EXPANSION SHAFT.

THERE IS A TENSION CONTROL SYSTEM THAT WORKS THROUGH A PNEUMATIC DISK BRAKE WITH A REPLACEABLE PADS SYSTEM.

THE UNWINDER HAS A PIVOTABLE ROLLER SYSTEM WHEREBY TENSION MAY BE MODIFIED ON ONE END TO REDUCE TENSION DIFFERENCE ON MATERIAL IF NECESSARY.

THE SAFETY CHUCK HAS A MECHANICAL MOVEMENT SYSTEM FOR SHAFT INSERTION.

THE UNWINDER HAS AN ULTRASONIC OR LASER SENSOR FOR A REAL MEASURING OF ROLL DIAMETER. THIS INFORMATION WILL HELP TO KEEP A SPECIFIC TENSION ON MATERIAL DURING ALL THE PROCESS.

 

CUTTING:

THE LONGITUDINAL SHEAR CUT SYSTEM GUARANTEES CLEAN AND SAFE TRIMMING AT EVERY MODULE. THE CUTTING SYSTEM ADAPTED TO THE MAIN TRANSMISSION GUARANTEES AN OVER SPEED THAT MAY BE REGULATED ACCORDING TO THE MATERIAL DURING EVERY STAGE OF PROCESS. THE PNEUMATIC ACTIVATION KNIVES WILL ALLOW A FAST MODIFICATION OF THE CUTTING MEASUREMENTS.

THIS ROLLER IS LOCATED AT AN EASY ACCESS AREA FOR THE OPERATOR TO BE ABLE TO MAKE CHANGES ON THE CUTTING WIDTH SAFELY. THE COUNTER KNIVES ARE ASSEMBLED TO THE ROLLER BY 3 SETSCREWS THAT FIX THEIR POSITION ON THE ROLLER. THE COUNTERKNIVES HAVE TWO FACES, SO WHEN THE FIRST FACE HAS AN IMPORTANT WEAR, IT WILL BE REMOVED FROM THE ROLLER AND THE NEW FACE WILL BE PLACED INSTEAD. THIS WILL EXTEND THE LIFESPAN OF THIS IMPORTANT COMPONENT.

SHEAR CUT KNIVES: THERE IS AN ADJUSTMENT MECHANISM TO PLACE THEM ON THE COUNTER KNIFE AND TO ADJUST THE CUTTING LOAD ACCURATELY. THE COUNTER KNIVES ARE SUPPORTED TOWARDS THE ROLLER IN ORDER TO OBTAIN A CUTOFF. THE SPEED ON THIS SYSTEM IS AN OVER SPEED IN RELATION TO THAT OF THE MATERIAL, IN ORDER TO GENERATE A CLEAN CUT.

LONGITUDINAL SHEAR CUT: PNEUMATIC ACTIVATION.

COUNTER KNIVES ROLLER WITH 3 SUPPORT PLANES FOR THE COUNTER KNIVES; 120° DISPLACEMENT FROM EACH OTHER.

19 SLITTERS ARE INCLUDED.

 

REWINDER:

PERIPHERAL REWINDER FOR NONWOVEN. THIS SYSTEM HAS A COUPLE OF MAIN ROLLERS WHERE THE MATERIAL ROLL IS FORMED.

THIS SYSTEM HAS LINEAR GUIDES FOR COMPACTION THROUGH WICH A NIP IS OBTAINED ON THE MATERIAL. THE REWINDER WILL HAVE A TRANSMISSION BASED ON A VECTORIAL-TYPE MOTOR ADAPTED TO A CYCLOIDAL REDUCER. THE TRANSMISSION HAS A MECHANICAL TORQUE CONTROL SYSTEM TO CONTROL THE TORQUE DIFFERENTIAL BETWEEN MAIN ROLLS.

THIS SYSTEM WILL HAVE A 3” EXPANSION SHAFT WHERE THE CARDBOARD CORES WILL BE INSERTED AND THE MATERIAL ROLLS WILL BE FORMED.

 

FABRIC OPENING SYSTEM:

THIS SYSTEM IS BASED ON A VARIABLE CURVATURE SYSTEM BY A CENTER KNOB AND IT IS A BAR- TYPE SYSTEM. THIS KNOB IS THERE TO CONTROL THE CURVATURE OF THE BAR WHERE MATERIAL SLIDES THROUGH. THE SLIDING BAR IS MADE OUT OF AN ULTRA LOW FRICTION MATERIAL IN ORDER TO GENERATE A SMOOTH SLIDING OF MATERIAL WITHOUT ANY TENSION ADDED. THIS WILL REDUCE WRINKLES IN A SIGNIFICANT WAY.

 

AUTOMATIC TENSION SYSTEM:

THERE IS AN OPEN LOOP AUTOMATIC TENSION CONTROL SYSTEM WITH A SENSOR FOR DIAMETER MEASURING. BY THIS SYSTEM, A REAL VALUE OF DIAMETER IS OBTAINED AT THE REWINDER. PRESSURE OF PNEUMATIC BRAKE VARIES DURING PROCESS.

 

MANUAL POSITIONING (OPTIONAL):

THE MANUAL POSITIONING SYSTEM IS BASED ON THE POSITION CONTROL OF THE COUNTER KNIVES. THE MODULE IS POSITIONED AT A DESIRED CUTTING PARAMETER AND THE COUNTER KNIFE WILL PHYSICALLY COME ACROSS IT. THE REAL POSITION OF MODULE WILL BE SHOWN ON A SCREEN THAT OPERATOR WILL BE CONSTANTLY SUPERVISING. THIS SCREEN WILL SHOW THE REAL MEASUREMENTS OF THE CARRIAGE IN RELATION TO THE LAST ONE OR AS AN ABSOLUTE REFERENCE. OPERATOR WILL BE ABLE TO RESET THE MEASUREMENT ONCE THE COUNTER KNIFE IS REPLACED AND WILL REPEAT THIS PROCESS EVERY TIME A COUNTER KNIFE IS POSITIONED.

A DISPLAY WILL SHOW THE DESIRED POSITION IN MILLIMETERS OR INCHES.

THIS SYSTEM CAN SHOW MEASUREMENT IN AN EITHER ABSOLUTE OR INCREASING WAY.

POSITION TOLERANCE: +/- 0.30 mm.

THE POSITIONER IS INSTALLED ON A SUPPORT THAT WILL BE LOCATED ON THE REWINDER BENCHES. THEREFORE, THERE WILL BE AN EASY ACCESS TO SYSTEM AND AN EASY REPETITION OF POSITIONING PROCESS.

 

UNLOADING ROLL TABLE:

A HYDRAULIC PIVOTEABLE TABLE WILL HAVE AS MAIN FUNCTION THE UNLOADING OF FINISHED ROLLS THAT THEN WILL BE LOCATED ON FLOOR LEVEL. THIS SYSTEM WILL EJECT THE ROLL AND THEN IT WILL BE RECEIVED AT THE PIVOTING TABLE FOR AN EFFICIENT UNLOADING.

THE UNLOADING TABLE WILL ALSO WORK AS A PROTECTION FOR THE OPERATOR.

THIS EQUIPMENT WILL HAVE SECURITY CURTAINS AT FRONT TO KEEP OPERATOR FROM ENTERING THE REWINDING AREA. THERE WILL BE AN EMERGENCY STOP BUTTON OR WIRE WHERE OPERATOR WORKS AND WILL ALSO HAVE PHYSICAL PROTECTION WITH SECURITY SWITCHES AT CUTTING AREA.

 

CONTROL:

HMI CENTRAL CONTROL SYSTEM WITH TOUCH SCREEN TO PROGRAM THE OPERATION CYCLE AND ALL THE MATERIAL CHARACTERISTICS. OPERATOR WILL HAVE ACCESS TO ALL OPERATION PARAMETERS IN ORDER TO BE ABLE TO MAKE CHANGES ON THE EQUIPMENT OPERATION CONDITIONS, AND THEREFORE OBTAIN MATERIAL ROLLS WITH SPECIFIC DENSITIES.

TRANSMISSION: VECTORIAL MOTO REDUCER WITH 1000:1 TORQUE.

DIGITAL METER COUNTER WITH DISPLAY AND AUTOMATIC STOP AT DEFINED DISTANCE.

 

DOCUMENTS INCLUDED:

THE MACHINE WILL BE DELIVERED WITH THE FOLLOWING DOCUMENT:

OPERATION MANUAL

MAINTENANCE MANUAL

SAFETY MANUAL

ELECTRIC DIAGRAMS

CONTROL SYSTEM MANUAL

PLC BACKUP

REQUIREMENTS:

ELECTRIC 15 KW, 440 VAC, TRI PHASE.

PNEUMATIC 6 BAR - 60 LTS. / MIN.

 

DUCTS AND WIRING:

DUCTS AND WIRES RUNNING FROM UTILITIES SOURCES TO THE CONTROL PANEL AND FROM THE CONTROL PANEL TO THE MACHINE WILL BE AT CUSTOMER COSTS AND MUST BE DONE ACCORDING TO THE INSTRUCTIONS SHOWN IN OUR DIAGRAMS

 

SIEMENS PLC

Learn More

REFERENCE NUMBER: P-1232 NOWO BLOW FIBRE FILLING LINES YEAR 2004/2006 CYCLONE WITH 2 DUST BAGS NOWO BLOW FIBRE FILLING LINES YEAR: 2004 CYCLONE WITH 2 DUST BAGS SILO IMS500 SPRAY 50 BALL FIBRE MACHINE EXCLUDING CONTROL PLC AND SCREEN – AVAILABLE FOR EXTRA COST LINE 1 SILO 500-3 YEAR 2004 WEIGHING UNIT YEAR 2004 BLOW FILLING STATION WITH TABLE LINE 2 SUITABLE FOR FEATHER AND FIBRE SILO IMS 1000 YEAR 2006 WEIGHING UNIT YEAR 2004 BLOWING STATION WITH TABLE BLENDING MACHINE MIXING CHAMBER BS 8 FOR FEATHER and POLYESTER YEAR 2006 FIRE RETARDANT APPLICATOR * THE BALL FIBRE MACHINE (ROTOR AND CYCLONE) INCLUDES THE PANEL BUT EXCLUDES THE TOUCH SCREEN AND PLC AS THESE CONTROL ANOTHER ROTOR WHICH THE CUSTOMER IS RETAINING. WE CAN SUPPLY A NEW PLC AND SCREEN (EXTRA PRICE) OR YOU CAN DO IT IN-HOUSE IT DOES NOT INCLUDE A BALE OPENER OR PRE-OPENER QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: G-4426 SLAUGHTER LINE FOR CATTLE (300 PD) AND SHEEP (1000 PD) QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: G-0929 FOAM PROFILE CUTTING MACHINE FOR DOUBLE MATTRESSES WORKING CUTTING WIDTH: 1800mm WORKING CUTTING LENGTH: 2100mm MAXIMUM HEIGHT FROM TABLE TO BLADE: 0/250mm LOADING TABLE: 2200 X 1980mm VERTICAL STROKE OF THE PRESS-CONVEYOR: 0/250mm PASSAGE BETWEEN OUTPUT ROLLER AND TABLE: 25/540mm MAXIMUM HEIGHT OF FOAM TO BE WORKED: 220mm MAXIMUM MATTRESS DIMENSION: 1960 X 2100mm TABLE SPEED: 0-20 M/MIN POWER KW: 15 WEIGHT APPROXIMATELY: 4900 KGS QUANTITY AVAILABLE: 1 Learn More

R-3243 COFFEE ROASTERS COMPLETE PLANT TAKE OVER, CAPACITY 4,200 LBS PER HOUR

TWO (2) COMPLETELY AUTOMATIC AND DIGITAL JABEZ BURNS 23R 4 BAG ROASTERS, PROGRAMMED RECIPES, AUTOMATED BUCKET ELEVATORS, DESTONER, MICRO FILTER GREEN BEAN CLEANER, AFTERBURNER FOR BOTH ROASTERS INCLUDES:
- FIRST ROASTER: JABEZ BURNS GAS-FIRED BATCH COFFEE ROASTER, MODEL 23R ACO THERMALO, (MODEL 23R-02309 ON CONTROL PANEL), C/W MAXON OVENPAK GAS BURNER, MODEL 400, SIZE 422M, (ROASTER REBUILT 2013), C/W JABEZ BURNS AUTOMATIC CONTROL CONSOLE C/W ALLEN-BRADLEY PLC MODEL MICROLOGIX 1500, ALLEN-BRADLEY HMI CONTROL MODEL PANELVIEW 550, PRINTER, & WORKSTATION, (ROASTER "A")
- SECOND ROASTER: JABEZ BURNS GAS-FIRED BATCH COFFEE ROASTER, MODEL 23R ACO THERMALO (MODEL 23R-04307 ON CONTROL PANEL), C/W MAXON OVENPAK GAS BURNER, MODEL 400, SIZE 422M, (ROASTER REBUILT 2013), C/W JABEZ BURNS AUTOMATIC CONTROL CONSOLE C/W ALLEN-BRADLEY PLC MODEL MICROLOGIX 1500, ALLEN-BRADLEY HMI CONTROL MODEL PANELVIEW 550, PRINTER, & WORKSTATION, (ROASTER "B")
- TWO: JABEZ BURNS COOLER/STIRRER/DE-STONER MODEL STIRFLEX C/W AIRVEYING DISCHARGE DUCT, ERIEZ MAGNET MODEL 20" RE RPS, STYLE 9706716, W/ S/S ENCLOSURE, & S/S HOOD W/ LIGHTING
- S/S EXHAUST HOOD OVER COFFEE DUMP BIN C/W EXHAUST FAN & DUCTING
- UNIVERSAL BUCKET ELEVATOR W/ AIRVEYING PIPE TO GREEN BEAN CLEANER
- HAMATEC ROTARY SCREEN GREEN BEAN CLEANER, TYPE KSD500/1200AM, (2007), C/W LEESON AC VARIABLE SPEED MOTOR CONTROL
- MACTIFLO DUST COLLECTOR W/ DRUM DISCHARGE, C/W NATIONAL CONTROLS INTELLIGENT DUST CONTROL MODEL DNC-T2310-A10
- UNIVERSAL BUCKET ELEVATOR (FROM GREEN BEAN CLEANER), MODEL D3-100ED, C/W PNEUMATIC DISCHARGE GATE, (2) BEAN LOADING CONTROL PANELS, & (2) AIRVEYING PIPES TO ROASTER "A" & ROASTER "B"
- TWO: ROASTED COFFEE BEAN ELEVATED HOLDING BIN C/W PNEUMATIC DISCHARGE GATE & AIRVEYING DISCHARGE PIPE
- CIRCULATING BLOWER FOR ROASTING LINE "A" C/W SUPPORT PLATFORM
- ELEVATED CHAFF COLLECTION CYCLONE W/ DRUM DISCHARGE
- CIRCULATING BLOWER FOR ROASTING LINE "B" C/W SUPPORT PLATFORM
- MARS 4' X 4' FLOOR PLATFORM SCALE C/W DIGITAL WEIGHT INDICATOR, MODEL MSF-445, 5,000 LB. CAP. (SUBJECT TO CONFIRMATION) 24" X 30" PLATFORM SCALE C/W DIGITAL WEIGHT INDICATOR
- INPROHEAT INDUSTRIES NATURAL GAS THERMAL OXIDIZER AFTERBURNER, MAX. INPUT 1.4MM BTU/HR C/W MAXON OVENPAK-II GAS BURNER, SIZE 425, CONTROL PANEL C/W TEMPERATURE RECORDER AND HONEYWELL BURNER CONTROL

 

Learn More

TT-7928 SHEARLINE SL41 ROLLER DIE-CUTTER – NEW, 41” 1. SHEARLINE SL41 ROLLER DIE CUTTER 41” 2. TYPE: NEW FLATBED ROLLER DIE CUTTERS 3. BRAND: SHEARLINE 4. MODEL: SL41 QUANTITY: 1 Learn More