TT-2153 SIEMENS SGT-800 GAS TURBINE, 54 MW, 11 KV, 50 Hz AND 1500 RPM, FUEL NATURAL GAS, FREQUENCY 50/60 Hz GROSS EFFICIENCY 38.86.0% HEAT RATE9, 256 KJ/KWH
UNUSED
CONDITION: EXCELLENT (NEW SURPLUS)
TURBINES STORED TO SIEMENS RECOMMENDATION.
NOTE: THIS IS A PACKAGE DEAL AND
REQUIRES BUYER TO PURCHASE ALL 3 UNITS. POI AND POF REQUIRED UPFRONT.
QUANTITY: 3
Learn More
V-2042 WATER RECIRCULATION SYSTEM FOR WATERJETS
6 LITERS PER MINUTE MAXIMUM
JET HEAD USES 1 TO 2 LITERS PER MINUTE
FILTRATION: FROM 5 TO 10 MICRONS
Learn More
J-4630 DOUBLE SHAFT SHREDDER, CHAMBER DIMENSIONS 1500mm LENGTH x 950mm WIDTH
DOUBLE SHAFT SHREDDER
KNIVES: 22 PIECES, SIZE Ø500mm x 70mm, MATERIAL 55SRCI
SPACERS: 22 PIECES, SIZE Ø290mm x 70mm, MATERIAL 45C STEEL
SHAFTS: 2 PIECES, SIZE Ø240mm x 2400mm, MATERIAL 42CRMO
CHAMBER DIMENSIONS: 1500mm LENGTH x 950mm WIDTH
SPEED: 10 RPM (SPEED IS FIXED AND CAN NOT BE ADJUSTED)
DIAMETER OF BARE ROLL (WITHOUT TEETH): 420mm FROM INNER TO THE TEETH BOTTOM DIAMETER, TEETH DEPTH IS 40mm (TOTAL OUTER DIAMETER OF BLADE IS 500mm)
SHAFT DIAMETER: 240mm
MOTOR POWER: 37 KW (2 PIECES)
REDUCER: K SERIES (2 PIECES)
VOLTAGE: 480 VOLTS
WEIGHT: 12,000 KGS
QUANTITY: 1
Learn More
YY-2208 HUMAN CREMATION MACHINE, LIGHT DIESEL FUEL, GAS, NATURAL GAS, LIQUEFIED GAS
DETAILS:
1. INCORPORATES EFFICIENT HEAT EXCHANGER AND SPECIAL AIR PATH STRUCTURE, MAKE FULL USE OF WASTE HEAT COMBUSTION FUEL GAS, IMPROVING HEAT UTILIZATION RATE, GOOD ENVIRONMENTAL PROTECTION INDEX, SAVES FUEL AND SHORTENS CREMATION TIME.
2. NEW REFRACTORY MATERIALS (EXCLUSIVE FORMULA) THAT ARE RESISTANT TO HIGH TEMPERATURE WITH LOW SPECIFIC HEAT. GREATLY EXTEND THE SERVICE LIFE.
3. SPECIAL CASTING MATERIAL, HIGH TEMPERATURE RESISTANCE, LONG SERVICE LIFE; SHORTENS THE COOLING CYCLE. THE BRICK STRUCTURE ON BOTH SIDES OF THE ASH PICKING FURNACE DOOR WILL NOT HAVE CRACKS CAUSED BY DESIGN OR QUALITY PROBLEMS GUARANTEED FOR ONE YEAR.
REFRACTORY MATERIALS, THE FURNACE CONTACT ARE WITH FLAME HAS PHOSPHORIC ACID A CHARACTERISTIC COMBINATION BRICK WHICH CAN RESIST RAPID COOLING AND RAPID HEAT, AND THE ARCHED ROOF INCORPORATES HIGH ALUMINUM SINTERED MOLDING BRICK.
THE FURNACE BODY IS SURROUNDED BY ALUMINUM SILICATE WOOL WITH GOOD HEAT INSULATION AND HEAT PRESERVATION PERFORMANCE. THE THICKNESS IS 180mm.
4. ALL OPERATING SYSTEMS OF THE EQUIPMENT HAVE THREE SETS OF OPERATION FUNCTIONS, NAMELY AUTOMATIC, SEMI-AUTOMATIC AND MANUAL, WHICH CAN BE SWITCH BETWEEN THEM WITHOUT INTERFERENCE. AUTOMATIC CONTROL, TELECOMMUNICATION OPERATION AND ANIMATION DISPLAY. KEEPING THE OPERATOR AWAY FROM THE CREMATION SITE AND PROTECTING THE OPERATOR. AT THE SAME TIME EQUIPPED WITH A STANDBY OPERATING SYSTEM.
LOW NOISE MOTOR EQUIPMENT, THERMOCOUPLE RESISTANCE TO HIGH TEMPERATURE. ALL ELECTRICAL CABINETS OF THE EQUIPMENT ARE EXTERNAL.
5. THE OIL SUPPLY SYSTEM INCORPORATES AUTOMATIC CONTROL AND MANUAL CONTROL, AND INCORPORATES OIL PROTECTION TECHNOLOGY, WHICH CAN EFFECTIVELY PREVENT FUEL OIL FROM RUNNING, BUBBLING, LEAKING AND CAUSING FURNACE EXPLOSION ACCIDENTS INCLUDING ANTI-LEAKAGE TECHNOLOGY TO BETTER PROTECT THE PERSONAL SAFETY OF OPERATORS.
6. THE BLOWER, THE INDUCED DRAFT FAN, THE FURNACE DOOR MOTOR, THE BODY CART MOTOR, THE PREPARATORY DOOR MOTOR AND THE FLUE GATE MOTOR ARE ALL INSTALLED WITH AN INTEGRATED DEVICE FOR OVER-CURRENT AND SHORT-CIRCUIT PROTECTION.
7. SPECIAL DIESEL METERING DEVICE, ACCURATE METERING.
QUANTITY: 1 Learn More
TT-1316 NONWOVEN MIDDLE SPEED NEEDLE LOOM, WORKING WIDTH 3200mm
MACHINE STRUCTURE FEATURES:
1. SPLICING TYPE STRUCTURE, IT IS MADE BY HIGH QUALITY Q235 STEEL PLATE WELDING, THEN FINE TEMPERING QUALITATIVELY WITH SUFFICIENT COMPLETENESS AND STABILITY. UPPER AND DOWN MACHINE GIRDERS BOTH PRECISELY PROCESSING MACHINED.
2. ECCENTRIC BEARINGS ADOPT TORRINGTON FAMOUS BRAND
3. MAIN SHAFT IS USING 42CROMO MATERIAL. AFTER CONDITIONING TREATMENT FINE FINISHING AND GRINDING.
4. NEEDLE GIRDER HIGH SPEED TURBINE ELECTRIC LIFTING, STRIPPER PLATE TURBINE ELECTRIC LIFTING, NEEDLE GIRDER ROLLER SCALE DISPLAY. AIR LOCKED THE NEEDLE PLATE TIGHTLY.
5. NEEDLE PLATE LUOYANG MADE BY MAGNESIUM ALLOY DIE CASTING PLATE COMPOSITE PU, RADON ARRANGE NEEDLES HOLE φ1.82mm
6. INPUT PVC LATTICE, OUTPUT ROLLER ADOPTS φ155mm, HIGH QUALITY SEAMLESS STEEL PIPE, AFTER FINISHING GRINDING, THE SURFACE IS PLATED WITH HARD CHROME, UPPER ROLLER ADJUSTABLE HEIGHT AIR CYLINDER.
7. MAIN MOTOR, OUTPUT ROLLER ALL FREQUENCY CONTROL.
8. INSTALLED POWER: AROUND 15.5KW, MAIN MOTOR 11 KW.
QUANTITY: 1 SET
Learn More
YY-2029 FULLY AUTOMATIC FOUR EDGE-SEALING GAUZE PACKING MACHINE
TECHNICAL PARAMETERS:
1. BAG SIZE: BASED ON CUSTOMER'S REQUEST;
2. SPEED: 120 TO 180 BAGS/MIN;
3. PACKING MATERIALS: PAPER + PAPER, PAPER + PLASTIC,
4. PACKAGE MATERIAL DIAMETER Φ≤350mm, WIDTH IS BASED ON CUSTOMER'S REQUEST;
5. VOLTAGE: 3 PHASE 380V 50Hz OR 220V 50/60Hz;
6. MOTORS:
a. SERVO MOTOR 1.5KW
b. SERVO MOTOR: 1KW
c. STEPPING MOTOR 110
d. STEPPING MOTOR VARIABLE FREQUENCY MOTOR 0.37KW
7. TOTAL OF 5 MOTORS IS 4KW
8. USES 28 VOLT FOR THE HEAT CIRCUIT, 2 HEATING PANELS, EACH PANEL WITH 8 HEATING TUBES, EACH TUBE IS 300 W, TOTAL 4.8 KW;
9. MACHINE WEIGHT: 800 KG;
10. MACHINE SIZE: LENGTH 5000 × WIDTH 1300 × HEIGHT 1600mm;
11. CRATE SHIPPING DATA: LENGTH 2600 × WIDTH 1900 × HEIGHT 1800mm.
12. TOTAL OF 5 MOTORS IS: 4KW
QUANTITY: 1
Learn More
YY-1366 BAG CLOSING MACHINE HEAD, INSTRUCTION MANUAL
FOR OPENRATOR SAFETY:
- THIS MANUAL BOOK CONTAINS INSTRUCTIONS AND PRECAUTIONS FOR USING THE BAG CLOSING MACHINE HEAD. BE SURE TO READ AND UNDERSTAND THE MANUAL BOOK BEFORE USING THE MACHINES.
- KEEP THIS MANUAL BOOK NEAR THE SEWING MACHINE FOR REFERENCE. BE SURE TO ATTACH THIS MANUAL BOOK TO THE MACHINE WHEN LENDING OR TRANSFER IT TO ANOTHER PERSON OR COMPANY.
- PLEASE CONTACT THIS MANUAL BOOK FROM US IF IT LOST.
- THE CONTENTS OF THIS MANUAL BOOK ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE FOR IMPROVEMENT AND SAFETY PURPOSE. Learn More
TT-2153 SIEMENS SGT-800 GAS TURBINE, 54 MW, 11 KV, 50 Hz AND 1500 RPM, FUEL NATURAL GAS, FREQUENCY 50/60 HzTT-2153 SIEMENS SGT-800 GAS TURBINE, 54 MW, 11 KV, 50 Hz AND 1500 RPM, FUEL NATURAL GAS, FREQUENCY 50/60 Hz GROSS EFFICIENCY 38.86.0% HEAT RATE9, 256 KJ/KWH UNUSED CONDITION: EXCELLENT (NEW SURPLUS) TURBINES STORED TO SIEMENS RECOMMENDATION. NOTE: THIS IS A PACKAGE DEAL AND REQUIRES BUYER TO PURCHASE ALL 3 UNITS. POI AND POF REQUIRED UPFRONT. QUANTITY: 3 Learn More
V-2042 WATER RECIRCULATION SYSTEM FOR WATERJETSV-2042 WATER RECIRCULATION SYSTEM FOR WATERJETS 6 LITERS PER MINUTE MAXIMUM JET HEAD USES 1 TO 2 LITERS PER MINUTE FILTRATION: FROM 5 TO 10 MICRONS Learn More
J-4630 DOUBLE SHAFT SHREDDER, CHAMBER DIMENSIONS 1500mm LENGTH x 950mm WIDTHJ-4630 DOUBLE SHAFT SHREDDER, CHAMBER DIMENSIONS 1500mm LENGTH x 950mm WIDTH DOUBLE SHAFT SHREDDER KNIVES: 22 PIECES, SIZE Ø500mm x 70mm, MATERIAL 55SRCI SPACERS: 22 PIECES, SIZE Ø290mm x 70mm, MATERIAL 45C STEEL SHAFTS: 2 PIECES, SIZE Ø240mm x 2400mm, MATERIAL 42CRMO CHAMBER DIMENSIONS: 1500mm LENGTH x 950mm WIDTH SPEED: 10 RPM (SPEED IS FIXED AND CAN NOT BE ADJUSTED) DIAMETER OF BARE ROLL (WITHOUT TEETH): 420mm FROM INNER TO THE TEETH BOTTOM DIAMETER, TEETH DEPTH IS 40mm (TOTAL OUTER DIAMETER OF BLADE IS 500mm) SHAFT DIAMETER: 240mm MOTOR POWER: 37 KW (2 PIECES) REDUCER: K SERIES (2 PIECES) VOLTAGE: 480 VOLTS WEIGHT: 12,000 KGS QUANTITY: 1 Learn More
YY-2208 HUMAN CREMATION MACHINE, LIGHT DIESEL FUEL, GAS, NATURAL GAS, LIQUEFIED GASYY-2208 HUMAN CREMATION MACHINE, LIGHT DIESEL FUEL, GAS, NATURAL GAS, LIQUEFIED GAS DETAILS: 1. INCORPORATES EFFICIENT HEAT EXCHANGER AND SPECIAL AIR PATH STRUCTURE, MAKE FULL USE OF WASTE HEAT COMBUSTION FUEL GAS, IMPROVING HEAT UTILIZATION RATE, GOOD ENVIRONMENTAL PROTECTION INDEX, SAVES FUEL AND SHORTENS CREMATION TIME. 2. NEW REFRACTORY MATERIALS (EXCLUSIVE FORMULA) THAT ARE RESISTANT TO HIGH TEMPERATURE WITH LOW SPECIFIC HEAT. GREATLY EXTEND THE SERVICE LIFE. 3. SPECIAL CASTING MATERIAL, HIGH TEMPERATURE RESISTANCE, LONG SERVICE LIFE; SHORTENS THE COOLING CYCLE. THE BRICK STRUCTURE ON BOTH SIDES OF THE ASH PICKING FURNACE DOOR WILL NOT HAVE CRACKS CAUSED BY DESIGN OR QUALITY PROBLEMS GUARANTEED FOR ONE YEAR. REFRACTORY MATERIALS, THE FURNACE CONTACT ARE WITH FLAME HAS PHOSPHORIC ACID A CHARACTERISTIC COMBINATION BRICK WHICH CAN RESIST RAPID COOLING AND RAPID HEAT, AND THE ARCHED ROOF INCORPORATES HIGH ALUMINUM SINTERED MOLDING BRICK. THE FURNACE BODY IS SURROUNDED BY ALUMINUM SILICATE WOOL WITH GOOD HEAT INSULATION AND HEAT PRESERVATION PERFORMANCE. THE THICKNESS IS 180mm. 4. ALL OPERATING SYSTEMS OF THE EQUIPMENT HAVE THREE SETS OF OPERATION FUNCTIONS, NAMELY AUTOMATIC, SEMI-AUTOMATIC AND MANUAL, WHICH CAN BE SWITCH BETWEEN THEM WITHOUT INTERFERENCE. AUTOMATIC CONTROL, TELECOMMUNICATION OPERATION AND ANIMATION DISPLAY. KEEPING THE OPERATOR AWAY FROM THE CREMATION SITE AND PROTECTING THE OPERATOR. AT THE SAME TIME EQUIPPED WITH A STANDBY OPERATING SYSTEM. LOW NOISE MOTOR EQUIPMENT, THERMOCOUPLE RESISTANCE TO HIGH TEMPERATURE. ALL ELECTRICAL CABINETS OF THE EQUIPMENT ARE EXTERNAL. 5. THE OIL SUPPLY SYSTEM INCORPORATES AUTOMATIC CONTROL AND MANUAL CONTROL, AND INCORPORATES OIL PROTECTION TECHNOLOGY, WHICH CAN EFFECTIVELY PREVENT FUEL OIL FROM RUNNING, BUBBLING, LEAKING AND CAUSING FURNACE EXPLOSION ACCIDENTS INCLUDING ANTI-LEAKAGE TECHNOLOGY TO BETTER PROTECT THE PERSONAL SAFETY OF OPERATORS. 6. THE BLOWER, THE INDUCED DRAFT FAN, THE FURNACE DOOR MOTOR, THE BODY CART MOTOR, THE PREPARATORY DOOR MOTOR AND THE FLUE GATE MOTOR ARE ALL INSTALLED WITH AN INTEGRATED DEVICE FOR OVER-CURRENT AND SHORT-CIRCUIT PROTECTION. 7. SPECIAL DIESEL METERING DEVICE, ACCURATE METERING. QUANTITY: 1 Learn More
TT-1335 S&S DRILLING RIG - NEVER USED, YEAR 2011TT-1335 S&S DRILLING RIG - NEVER USED, YEAR 2011 S&S DRILLING RIG DRILLING RIG (NEVER USED) YEAR 2011 HOURS: MINIMAL MILES: MINIMAL NEW SURPLUS UNIT - NEVER USED GENERAL RIG SPECIFICATIONS: HP RATING: 550HP AMBIENT RATING: 50-55⁰C POWERED BY: 1 X C15 CAT ENGINE (540 BHP @ 2,100 RPM) ALLISON 5610 TRANSMISSION RIG TYPE: SELF-PROPELLED, CARRIER MOUNTED, 6-AXLE (12X4), INTERNALLY GUYED QUANTITY: 1 Learn More
TT-1316 NONWOVEN MIDDLE SPEED NEEDLE LOOM, WORKING WIDTH 3200mmTT-1316 NONWOVEN MIDDLE SPEED NEEDLE LOOM, WORKING WIDTH 3200mm MACHINE STRUCTURE FEATURES: 1. SPLICING TYPE STRUCTURE, IT IS MADE BY HIGH QUALITY Q235 STEEL PLATE WELDING, THEN FINE TEMPERING QUALITATIVELY WITH SUFFICIENT COMPLETENESS AND STABILITY. UPPER AND DOWN MACHINE GIRDERS BOTH PRECISELY PROCESSING MACHINED. 2. ECCENTRIC BEARINGS ADOPT TORRINGTON FAMOUS BRAND 3. MAIN SHAFT IS USING 42CROMO MATERIAL. AFTER CONDITIONING TREATMENT FINE FINISHING AND GRINDING. 4. NEEDLE GIRDER HIGH SPEED TURBINE ELECTRIC LIFTING, STRIPPER PLATE TURBINE ELECTRIC LIFTING, NEEDLE GIRDER ROLLER SCALE DISPLAY. AIR LOCKED THE NEEDLE PLATE TIGHTLY. 5. NEEDLE PLATE LUOYANG MADE BY MAGNESIUM ALLOY DIE CASTING PLATE COMPOSITE PU, RADON ARRANGE NEEDLES HOLE φ1.82mm 6. INPUT PVC LATTICE, OUTPUT ROLLER ADOPTS φ155mm, HIGH QUALITY SEAMLESS STEEL PIPE, AFTER FINISHING GRINDING, THE SURFACE IS PLATED WITH HARD CHROME, UPPER ROLLER ADJUSTABLE HEIGHT AIR CYLINDER. 7. MAIN MOTOR, OUTPUT ROLLER ALL FREQUENCY CONTROL. 8. INSTALLED POWER: AROUND 15.5KW, MAIN MOTOR 11 KW. QUANTITY: 1 SET Learn More
YY-2130 FRAME PRESSURE WELDING MACHINE, OUTPUT 120 TO 220 PCS PER HOURYY-2130 FRAME PRESSURE WELDING MACHINE, OUTPUT 120 TO 220 PCS PER HOUR TECHNICAL PARAMETERS: WIRE GAUGE: Φ3-8mm (CUSTOMIZABLE) OUTPUT: 120 TO 220 PCS/H HYDRAULIC SYSTEM: 3 X AC380V 2.2KW 50/60Hz 8-10MPA 40 HYDRAULIC OIL OVERALL DIMENSI0ON: 1000 X 500 X 900mm WEIGHT: 100KG QUANTITY: 1 Learn More
TT-1174 DUSENBERY SLITTER REWINDER, YEAR 2000, WORKING WIDTH 2050mmTT-1174 DUSENBERY SLITTER REWINDER, YEAR 2000, WORKING WIDTH 2050mm GENERAL BRAND: DUSENBERY EUROPE LIMITED MODEL: 281 YEAR: 2000 SPEED: FOIL MAX. 400 M/MIN CARDBOARD MAX. 70 M/MIN QUANTITY: 1 Learn More
YY-2029 FULLY AUTOMATIC FOUR EDGE-SEALING GAUZE PACKING MACHINEYY-2029 FULLY AUTOMATIC FOUR EDGE-SEALING GAUZE PACKING MACHINE TECHNICAL PARAMETERS: 1. BAG SIZE: BASED ON CUSTOMER'S REQUEST; 2. SPEED: 120 TO 180 BAGS/MIN; 3. PACKING MATERIALS: PAPER + PAPER, PAPER + PLASTIC, 4. PACKAGE MATERIAL DIAMETER Φ≤350mm, WIDTH IS BASED ON CUSTOMER'S REQUEST; 5. VOLTAGE: 3 PHASE 380V 50Hz OR 220V 50/60Hz; 6. MOTORS: a. SERVO MOTOR 1.5KW b. SERVO MOTOR: 1KW c. STEPPING MOTOR 110 d. STEPPING MOTOR VARIABLE FREQUENCY MOTOR 0.37KW 7. TOTAL OF 5 MOTORS IS 4KW 8. USES 28 VOLT FOR THE HEAT CIRCUIT, 2 HEATING PANELS, EACH PANEL WITH 8 HEATING TUBES, EACH TUBE IS 300 W, TOTAL 4.8 KW; 9. MACHINE WEIGHT: 800 KG; 10. MACHINE SIZE: LENGTH 5000 × WIDTH 1300 × HEIGHT 1600mm; 11. CRATE SHIPPING DATA: LENGTH 2600 × WIDTH 1900 × HEIGHT 1800mm. 12. TOTAL OF 5 MOTORS IS: 4KW QUANTITY: 1 Learn More
YY-1366 (USERS MANUAL) BAG CLOSING MACHINE HEAD, INSTRUCTION MANUALYY-1366 BAG CLOSING MACHINE HEAD, INSTRUCTION MANUAL FOR OPENRATOR SAFETY: - THIS MANUAL BOOK CONTAINS INSTRUCTIONS AND PRECAUTIONS FOR USING THE BAG CLOSING MACHINE HEAD. BE SURE TO READ AND UNDERSTAND THE MANUAL BOOK BEFORE USING THE MACHINES. - KEEP THIS MANUAL BOOK NEAR THE SEWING MACHINE FOR REFERENCE. BE SURE TO ATTACH THIS MANUAL BOOK TO THE MACHINE WHEN LENDING OR TRANSFER IT TO ANOTHER PERSON OR COMPANY. - PLEASE CONTACT THIS MANUAL BOOK FROM US IF IT LOST. - THE CONTENTS OF THIS MANUAL BOOK ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE FOR IMPROVEMENT AND SAFETY PURPOSE. Learn More