NovaStar, SZ102, UV Sterilized Machine, 6000mm Total Length, 1000mm Entrance Width (New)

Description

  1. Overview
    1. Ultraviolet C disinfection technology is widely recognized for its disinfection effect on bacteria, viruses and other pathogenic bodies.
    2. The sterilization effect of ultraviolet ray to bacterium and virus is in a second commonly, while traditional chlorine and ozone methods take 20 to 50 minutes to achieve the same effect.
    3. Features high efficiency sterilization broad spectrum, no secondary pollution, safe and reasonable design, safe and reliable operation.
    4. Simple operation and maintenance, low cost.
    5. The equipment occupies a small area and has no noise.
    6. Continuous mass sterilization with wide application field.
    7. Ultraviolet light has strong power to bacteria but also has certain harm to human body; the most vulnerable part is the eye cornea, so never look at the lit lamp with eyes.
    8. Use common glass or transparent plastic film as a protective mask; never use quartz glass by mistake as ordinary glass is almost completely impermeable to ultraviolet light.
    9. If injured, facial burns heal after a few days; eye injury takes about three to four days to heal; seek medical advice immediately in case of injury.
  2. Maintenance
    1. Check regularly to ensure the normal operation of uv lamp.
    2. After continuous use of 9000 hours or one year, replace the ultraviolet lamp tube.
    3. When replacing new lamp tube, unplug lamp tube power socket first, then take out ultraviolet ray lamp tube.
    4. Do not touch the quartz glass of new lamp tube with finger, as blemish can affect lamplight strength.
    5. Put lamp tube into sterilizing machine inside cavity carefully.
  3. Specifications
    1. Total length of the equipment: 6000 mm
    2. Uv working area: 5000 mm
    3. Feeding area: 500 mm
    4. Discharging area: 500 mm
    5. Height of entrance and exit: adjustable
    6. Width of entrance and exit: 1000 mm
    7. Conveyor belt from the ground: 750 ± 50 mm
  4. Main Structure
    1. Outer body of working area tunnel: 1.2 mm stainless steel plate
    2. Working area tunnel cavity: 1.2 mm high-quality stainless steel plates
    3. Body support frame: one set of square steel
    4. Conveyor belt: advanced teflon meshbelt
    5. Conveying drum: clean and friction-resistant drum
    6. Conveying power: according to production needs, the conveying speed is adjustable from 0 to 20 m/min
  5. Electrical Equipment
    1. Mesh belt in organic speed range: 0 to 5 m/min adjustable
    2. Transport motor: 250 W
    3. Governor: step less speed regulation
    4. Ammeter: set of 20 A
    5. Operating voltage: 220 V / 60 Hz
  6. Uv Sterilization Part
    1. Sterilization lamp length: 550 to 1000 mm, using 40 sets of 150 W uv sterilization lamp
    2. Evenly distributed in the upper and lower left and right sides of the device in the furnace chamber, greatly improving the utilization rate of ultraviolet light up to 95% (sterilization time is about 1 minute)
    3. The inlet and outlet of the sterilization area is provided with a light-proof area, equipped with a hood and an adjustable baffle
    4. The shell is made of stainless steel, and the whole machine is corrosion-resistant and easy to clean
    5. The bottom is equipped with four brake type movable casters for easy movement
    6. Transmission part: the speed is adjusted by 250 W stepless speed regulating motor, with digital display step less speed regulating and linear speed meter; speed is uniform and adjustable from 0 to 5 m/min
    7. Incorporate advanced teflon net belt drive, the middle is equipped with a towing plate; front and rear are equipped with adjustable active and passive roller, which is conducive to the net belt not easily running sides or scraping its belt
    8. Equipped with automatic timer to monitor the use time of the lamp at any time to facilitate replacement; if the product can drop slag, a tray can be used on the conveyor belt sterilization
  7. Protection Device
    1. Over voltage over current protection
    2. Fault alarm prompt
    3. Device overload protection