Company founded 1975 US-based machinery business experienced in worldwide sales.

+1 (864) 574-0404
Global website

Choose your language

Languages follow BCP 47. Flags and countries are representative context only.

Automatic translation Machine specifications, model codes, and reference numbers should always be confirmed in the original listing.
Menu
Call +1 (864) 574-0404 Email Us

Morrison, Sanforizer, 1985, 76 inch Cylinder Width, 72 inch Palmers

Description

  1. Morrison Sanforizer
    1. Inventory number: E-833
    2. Year: 1985
    3. Scray adjustable height with Reliance Minitack Plus VS drive
    4. Cylinder is approximately 76 in wide
    5. Palmers 72 in
    6. Rubber roll 76 in
    7. Blanket 67 in
    8. Exit end has a Parkinson batcher, 2-roll batcher with pneumatic hold-down
    9. All DC driven
    10. Hot can at exit, mounted over batcher, 72 in
    11. Stranberg monitor indicator model 900 for stretch on the overfeed
    12. Control panel mounted to the side of the machine
    13. Reliance Electric engineered systems drive
  2. Artos Tenter Range
    1. 72 in wide, pin/clip combination
    2. Werner ceiling-mounted scray with single station unroll, pneumatic hold-down, has conveyor in lieu of pan, also with Mt. Hope 3-roll tension set with Horton clutch
    3. Werner padder, 70 in wide, approximately 10-ton capacity, rubber/rubber, Mt. Hope spring guiders at entry, (2) stainless steel guide rolls, single dip, bow roll and single roll compensator, 200 gal stainless steel dip tank with Master 3 hp gear motor mixer
    4. E-Vac 25 hp vacuum system model FR, series finishing system, vacuum level and chemical return pump, 2033 flow rate, motor 25 hp, 1770 rpm, 208/230/460 volt, Sutorbilt rotary positive blower
    5. Marshall & Williams gas-fired predryer, 6-burner, 220 volt, 3-phase
    6. Tenter frame, rated at 76 in max width and 70 ft length, presently 72 in width and total 67 ft length with 15 ft entry, 9 ft exit, 43 ft box section, frame with overfeed, E&L guiders, model FR1501, 3-finger uncurl ers, electric eye power opening, pinning brushes, 4-zone dryer box with 4 fans and 4 Honeywell burner safeguards, cooling chamber section at exit, Reliance "Power-Matched" series ES drive system
    7. Artos 3-roll crushing calender, steel/filled/steel, without heat
    8. Birch Brothers 3-roll batcher, 84 in
  3. Perkins 3-Roll C-Face Hydraulic Bottom Loading (Foil) Calender
    1. Model #BPH-60-60
    2. 30-ton capacity
    3. Top roll gas fired
    4. Center bowl is filled out to 61 in
    5. Top roll is driven
    6. Single bar let-off and single bar take-up
    7. Calender is gas heated
    8. 60 in cooling can at exit
    9. 60 in dry can at exit with a wooden slot expander
    10. Take-up is driven with Burton Ministack drive assembly
    11. Calender driven by Reliance Super RPM DC motor, 15 hp, 1750-2300 rpm, 150 volt
  4. Verduin 2-Roll C-Face Gas-Fired Calender
    1. 65 1/2 in wide filled bottom roll, not driven
    2. Motor driven 67 in wide steel top roll
    3. Single roll let-off front and back
    4. Maximum capacity 40 yards/min
    5. Motor driven rear take-up roll
    6. 72 in wide aluminum slot expander roll with (2) dancers
  5. Van-Type Inspection Machine
    1. Backlit board
    2. 72 in face
    3. 2-roll surface take-up
    4. Let-off in front and back
    5. Unit has no guiding
  6. Pernick Inspection Machine
    1. Model PC800
    2. Reversible
    3. Trumeter yardage counter
    4. Separately driven 4-roll let-off
    5. Separately driven 2-roll take-up
    6. Backlit inspection board
  7. Perkins 3-Roll 40-Ton C-Face Calender
    1. All 3 rolls bored for heating but not fired
    2. Unit run as cold calender
    3. Steel/nylon sleeve/steel
    4. Steel roll 67 in wide
    5. Nylon sleeve roll 66 in wide
    6. Motor driven let-off
    7. Motor driven take-up with Horton clutch at exit
  8. Arc Button Breaker
    1. 72 in face
    2. 72-roll
    3. Model #72BB72
    4. Fife inline guider
    5. 15 hp Baldor motor, 500 volt
    6. Large Super Chuck clutch on face and back
  9. Kusters Bleach Range
    1. 72, year 1984
    2. Let-off cradle, 4-roll, 70 in wide
    3. Vertical "J" scray
    4. Top nip with Mt. Hope 3-roll tension device, drive and Horton clutch
    5. Pair of Mt. Hope mechanical guiders
    6. Saturator box, rolls pneumatic rubber/rubber, 76 in face, approximately 3-ton pressure, 3-dip
    7. Conveyor steamer, type 266.2131, year 1984
    8. (3) wash boxes with nips, closed
    9. E-Vac 25 hp vacuum system, water removal only with filter and vacuum apparatus
    10. (15) Morrison dry cans in one vertical stack of 7 and another of 8, 80 in face, 105 psi, year 1978, U.L. approved
    11. Parkinson 3-roll batcher, 80, serrated knife, pneumatic hold-down, pneumatic doffing, motor drive in base
    12. Stainless steel tank 38 in dia. x 72 in deep, 3 hp homogenizing mixer
    13. Culligan 2-tank water softening system
  10. Mt. Hope Pneumatic Scray
    1. 70 in
    2. Pneumatic nip, grooved
    3. Adjustable pan
    4. Mounted overhead
  11. Parkinson 3-Roll Batcher
    1. 72 in wide
    2. Year 1985
    3. All pneumatic hold-downs and adjustment
  12. Gessner Napper
    1. 96 in double acting
  13. Scholl 2-Port Split/Split 4-Strand 1200 Lb Jet Dye Machine
    1. Year 1997
    2. Heat exchanger
    3. Stainless steel tank and air mixer
  14. Scholl 2-Port Split/Split 4-Strand 1200 Lb Jet Dye Machine
    1. Year 1995
    2. Heat exchanger
    3. Stainless steel tank and air mixer
  15. Culligan Water Softening Installation
    1. Estimated capacity 9,000 gal/day
    2. (2) enclosed media-filled de-ionizing tanks 2 ft dia. x 5 ft overall
    3. Open salt block and water tank 40 in dia. x 48 in height, plywood cover
    4. (2) duplex enclosed meters
    5. Piping and normal accessories and attachments
  16. Hydraxtor
    1. 36 in
    2. Rebuilt by Tandem-Flow Systems, Midwest Machinery Exchange Division
    3. Motor 7 1/2 hp, 230/460 volt