Company founded 1975 US-based machinery business experienced in worldwide sales.

+1 (864) 574-0404
Global website

Choose your language

Languages follow BCP 47. Flags and countries are representative context only.

Automatic translation Machine specifications, model codes, and reference numbers should always be confirmed in the original listing.
Menu
Call +1 (864) 574-0404 Email Us

Bruckner, Continuous Thermosol Dye Range, 100 inch Width

Description

  1. Wide Width Finishing Equipment
    1. Inventory number: E-3440
    2. Bruckner continuous thermosal dye range consists of:
    3. Bruckner J scray 100” wide
    4. Kusters dye padder type 222.11-2200 year 1991 (106-70561-01) double roll swimming pad, pair E & L guiders at entry
    5. 2 Bruckner pre-dryers mounted above
    6. 10 burners 5 per side of fabric
    7. 84” A-frame winder by Zollig surface batch wind
    8. Finish goods here or continue to Bruckner thermosal box mounted in air
    9. Throat cloth opening 96” wide
    10. 2 jacketed 250 gallon tanks mounted on top
    11. A-frame winder to run just as thermasol unit
    12. Set of dry cans 100” wide 27 cans total
    13. Set up small padder 2.4 m wide with a Bianco guiding and opening system & pan travel in through 20” Meco guiders over scroll roll over 100” cans using this is a small dye range as well
    14. Runs as independent
  2. Mcs Stainless Mercerizing Machine
    1. Stainless steel on framework, etc.
    2. 96” scray enters overhead into pair KF2020 guiders
    3. 3-rolls s/s and 3 expander rolls to tank
    4. Chemical add in tank for process of beginning mercerization has large rolls on top and 7 smaller drive rolls on bottom, roll faces 92”
    5. 92” rubber/stainless steel nip
    6. Next box is duplicate for mercerization continuation
    7. Covers on top to keep caustic down
    8. 8 rolls on bottom and 10 on top
    9. Rubber/stainless steel nip
    10. Stainless steel enclosed recovery washer double laced
    11. 90” rubber/rubber nip
    12. Next two enclosed boxes both have nips and they are double laced for final wash
    13. Exit with triple dip wash open with nip
    14. A-frame winder
    15. This machine was built in 1991 on 03/05 (7670) enough to trace with MCS
    16. Thermo electronica control panel
    17. CTM compressor small compressor necessary to run machine
  3. Guarneri Calendar
    1. Roll configuration: steel / poly nylon / cotton paper
    2. 2.6 meter usable width
    3. (3) roll heated – dynamic thermal oil
    4. A-frame entry
    5. 2-collers
    6. Top roll dia. 480 mm
    7. Middle roll dia. 600 mm
    8. Bottom roll dia. 600 mm
    9. 2.6 meter mercerizer
    10. Chainless
    11. Year 1999
    12. Total mass 23000 kg type E360-2600, 380 volt, 60 cycle, 3 phase, 56 kW
    13. Roll configuration: steel / poly nylon / cotton paper
    14. Polished steel top roll, plastic center sleeve roll, filled bottom roll, scroll roll entry, 3 bar tensioning, oil heated, A-frame chuck let-off, oil fed through central boiler system, calender exit A-frame let-off surface batch driven lint vacuum extraction system mounted
  4. Morrison Sanforizer
    1. Year 1991
    2. A-frame let off into scray
    3. Scray 91”
    4. Specialty 45 air guiders
    5. 90” cold spray unit
    6. Small steam box/curing box
    7. Morrison pup tenter tenter frame opens to 1.85 cm
    8. Morrison rubber belt section main carrier roll 90”
    9. Rubber belt 86” (belt poor condition needs to be replaced)
    10. Palmers 90” felt blanket 85 ½”
    11. Two palmers standard large/small (281-147) palmers are 4’ & 8’ diameter
    12. Pictures available
  5. Verduin 90” Calendar
    1. Gas heated
    2. S/f/s
    3. Standard let off & take up
    4. Top roll gas
    5. Bottom roll drilled for gas but plugged
  6. Bruckner Tenter Frame Combination Pin/Clip
    1. 50 cm – 2.4 m
    2. Year 1991
    3. Consists of:
    4. 100” entry scray
    5. Pair guiders mounted on back of r/r padder
    6. Padder slant “v” type Brucker 1991 (1.6057.02) 13 bar, 47 liter pan used for dyeing
    7. Mahlo weft straightener 100” wide equipped with E & L type SEO6202 guiders (#048178) 12” KF 20 guiders with 3-finger uncurlers mounted above straightener
    8. Pin/clip combination
    9. E & L power opening type FR1501, 3-finger E & L 10” uncurlers, power brushing, power opening, overfeed
    10. Operator’s panel in front giving Mahlo control for the moisture control & Mahlo screen, reading for the H2O with normal & abnormal
    11. Entry field approx. 20’ low profile oil heated
    12. 90’ long housing
    13. 5’ enclosed cooling section at exit end
    14. Standard Bruckner exit
    15. Enter either into a scray or pass into a set of 3-finger 18” uncurlers by E & L type SE06202 into either an A-frame or a box swing
    16. Mahlo RMS7 Ecomat ML7 mounted in addition to the weft straightener
    17. 8-compartment frame
  7. Vald Henricksen Pressure Jigger
    1. 100” beam
    2. Year 1987
    3. Design pressure 3-bars, design temp 140 c. total volume 11,500 liters, hydraulic test pressure 3.9 bars, Dutch seal temp of 1987
  8. Arioli Steamer
    1. Year 1991
    2. Double strand
    3. 3.6 meters wide for 3.2 meters fabric
    4. Pictures available
  9. Johannes Zimmer Rotary Printer
    1. Open bearing
    2. 8-colors
    3. Blanket 124” will print 110” maximum 3-sets of repeat heads with it
    4. Older
    5. Entry pair KF20 E & L guiders
    6. Thermal oil low profile
    7. 4-sections
    8. 9 fans
    9. Exit end KF20 guiders
    10. Brushing rolls
    11. Back has position for 2 A-frame winders for continuous run