Industrial brewery with capacity of 20 hl per brew.
Year productivity of 6,000 to 7,000 hl, 3 sorts of beer.
Brewery is not located at a seismic area.
Equipment designed according to European standard.
Brew House
Steam heated 2-vessel brew house of 20 hectolitres in stainless steel.
Malt mill: 1 x 2-roll mill with capacity of 400 to 800 kg/h with inlet from the top for malt sacks.
Mash/worth – kettle: double walled inner shell of stainless steel, material 1.4301 LLC, welds ground with grain size 220, outer sheath made of stainless steel.
2 steam heating zones (bottom and cylindrical part).
Agitator and shaft in stainless steel, material 1.4301, installation of bottom center, drive via gear motor, speed controllable by frequency converter.
1 spray ball.
1 man hole with glass.
1 pressure relief valve – safety valve.
1 level measurement.
Designed for non pressure operation.
Lauter tun: double walled inner shell of stainless steel, material 1.4301 IIIC, welds ground with grain size 220, outer sheath made of stainless steel.
Isolation of the cylindrical part and the bottom - 100 mm halogen-free mineral wool.
Bottom of the lauter tun with outlet valves, back wash valves and a drain valve.
Multipart sieve plate 1.4301 removable through manhole.
Hoeing 1.4301 two-armed with knives and trebern sword, installation of bottom center.
1 lauter station with CIP spray ball.
1 manhole with glass.
1 spray ball.
1 trebern flap at the cylindrical part.
Designed for non pressure operation.
The package includes all valves, check valves, butterfly valves, 2 pumps and temperature probes.
Landing and stairs made of stainless steel square roof bars, covered with corrugated sheet metal, height adjustable feet with domes.
The pan dust will be cold down with cold water and the condensate will be transferred to the drain.
Whirlpool 20 Hl
Vessel made of stainless steel, material 1.4301 IIIC, welds ground with grain size 220, non insulated.
1 whirlpool pump.
2 lateral outlets with hand valves.
1 floor drain with hand valve.
1 tangential inlet port with threaded connector.
1 safety valve.
1 manhole.
1 spray ball.
Designed for non pressure operation.
Worth Cooling and Worth Aeration
Vessel made of stainless steel, material 1.4301 IIIC, welds ground with grain size 220, non insulated.
1 whirlpool pump.
2 lateral outlets with hand valves.
1 floor drain with hand valve.
1 tangential inlet port with threaded connector.
1 safety valve.
1 manhole.
1 spray ball.
Designed for non pressure operation.
Section 1: 20 hl worth is cooled with cold water from 98°C to 17°C in 60 minutes (cold water from client side must be max. 15°C or lower).
Section 2: with ice water or glycol the worth is cooled to 5°C.
Control System
Each pneumatic controlled valve will have a switch button on a control panel in the middle of the brew house.
Also the temperature control of the mash kettle and worth kettle will be implemented at the control panel with a hardware controller.
Hot Water Tank 30 Hl
Vertical design, material 1.4301.
Double walled inner shell of stainless steel, material 1.4301 IIIC, welds ground with grain size 220.
Outer sheath made of material 1.4301 with grain 220.
1 hot water pump.
1 circulation pump.
1 PT 100 and controller.
1 steam valve and condensate valve.
1 level indication.
Cylinder Conical Tanks 40/48 Hl (10 Units)
Vertical design with dished bottom and 60° cone.
Cone and cylindrical part is insulated and the full tank is equipped with welded stainless steel exterior finish.
Tank height approx.: 4,050 mm.
Tank equipped with cooling jacket (1 zone) and cone cooling (2 zone), by temp-plate, suitable for ice water / glycol.
Separate connections for cooling for casing and cone: nipple ¾" external thread.
Tank with manhole 500 x 400 mm, with manhole cover and dual hinge.
2 outlet DN 32 installed in a DN 125 - thread, pulled forward and ended butterfly valve DN 32 G / S, with blanking cap.
Upper floor provided with 2 threaded connection DN 32 for connection of an RLV - fitting. One of the terminals installed in a fitting DN 100 and DN 25 provided with removable spray ball.
Cleaning pipe DN25, top provided with connection cone / nut DN 32 for connection to the RLV combination, pulled down and ending on operating height in threaded connection DN 50, including blanking cap.
In the cleaning duct 2 connector with threaded connection DN 20 for spund apparatus and with ball valve for the gas support.
1 connector for sample valve: threaded connection DN 20.
2 connection for PT -100: immersion sleeve 260 mm long, with sleeve ½".
2 solenoid valve for the cooling duct.
4 manual valves in the coolant inlet and coolant outlet line.
4 height adjustable tube feet, including footplate.
Tank suitable for 3 bar G (20°C), decrease according to PED 97/23/EC.
Filtration 20 Hl/H
Kiselgur-filter with horizontal slices and capacity of 20 hl / hour.
Pressure Dispensing Tanks 40/46 Hl (3 Units)
Vertical design with dished bottom.
Lower + upper bottom and cylindrical part is insulated and the full tank is equipped with welded stainless steel exterior finish.
Tank height approx.: 3,350 mm.
Tank equipped with cooling jacket (1 zone) by temp-plate, suitable for ice water / glycol.
Connection for cooling: nipple ¾" external thread.
Tank with manhole 500 x 400 mm, with manhole cover and dual hinge.
1 outlet DN 32 pulled forward and ended butterfly valve DN 32 G / S, with blanking cap.
Upper floor provided with 2 threaded connection DN 32 for connection of an RLV - fitting. One of the terminals installed in a fitting DN 100 and DN 25 provided with removable spray ball.
Cleaning pipe DN 25, top provided with connection cone / nut DN 32 for connection to the RLV combination, pulled down and ending on operating height in threaded connection DN 32, including blanking cap.
In the cleaning duct 2 connector with threaded connection DN 20 for spund apparatus and with ball valve for the gas support.
1 connector for sample valve: threaded connection DN 20.
1 connection for PT -100: immersion sleeve 260 mm long, with sleeve ½".
1 solenoid valve for the cooling duct.
2 manual valves in the coolant inlet and coolant outlet line.
4 height adjustable tube feet, including footplate.
Tank suitable for 3 bar G (20°C), decrease according to PED 97/23/EC.
Cooling Unit
Cooling unit for the offered tanks and for the worth cooling.
Designed for operation with glycol.
Compressor
Oil free.
Fully automatic, oil-free air compressor station with stage, mounted on a pressure vessel, equipped with pressure switch, outlet valve, safety valve, pressure gauge and micro filter.
Steam Generator
Oil operated steam generator with a capacity of 200 kg/h including feed water treatment and feed water control.
Request a Quote
✓
Request sent
Thank you, our team will reply to you shortly.
Direct access to our team
Email American Plant & Equipment
Tell us what you want to buy, source, finance, or sell. A machinery specialist will follow up with you.
✓
Thank you. Your request is with the American Plant and Equipment team.
A machinery specialist will follow up with you.
Machinery updates
Subscribe to our email list
Tell us which industries you follow and we will send you the machines that match.
✓
You are on the list.
We will email you when machines that match your interests come in. Unsubscribe from any message.
