NovaStar, MS571, Inclined Belt Conveyor, 940 m Horizontal Length, 800 mm Steel Cord Belt, 300 t/h, 20 Degrees (New)

Description

  1. Overview
    1. New fixed inclined belt conveyor for bulk rock, complete with drives, controls and belt
    2. Quantity: 7 identical units
    3. Horizontal conveyor length: 940 m (3,084 ft) each
    4. Lifting height: 340 m (1,115 ft)
    5. Inclination angle: 0 to 20 degrees
    6. Rated conveying capacity: 300 t/h (331 short tons per hour)
    7. Designed for barite rock, particle size up to 50 mm (2 in)
    8. Installation: outdoor, above ground
    9. Ambient temperature: -5 C to 48 C (23 F to 118 F)
    10. Weight: 207,351 kg (457,130 lb) each
  2. Belt
    1. Belt width: 800 mm (31.5 in)
    2. Steel cord belt ST2000, top and bottom covers 6 mm + 6 mm, DIN Y abrasion grade
    3. Belt length supplied: 2,025 m (6,644 ft) per unit
    4. Belt speed: 2.8 m/s (551 ft/min)
    5. Deep trough design, plain belt (no chevron pattern needed)
  3. Drive
    1. Dual head drive, 2 drive units per conveyor
    2. 2 x 4-pole explosion-proof variable-frequency motors, 480 V, 60 Hz
    3. 2 x reducers with cooling fan, ratio 28
    4. 2 x explosion-proof hydraulic couplings
    5. 2 x electro-hydraulic thruster explosion-proof brakes
    6. 2 x backstops (holdbacks)
    7. 2 x quick-release spring couplings, with high-speed and low-speed coupling guards
    8. 2 x drive pulleys, 1000 mm (39.4 in) diameter, cast diamond rubber lagging
    9. Bend pulleys 800, 630, 500 and 400 mm (31.5, 24.8, 19.7 and 15.7 in), cast rubber lagging
    10. Pulley bearings: SKF or FAG; motor and reducer bearings: NSK, FAG or SKF
  4. Idlers and Belt Cleaning
    1. 770 troughing forward-tilt carrying idler sets, 133 mm (5.2 in) rolls, 45 degrees
    2. 298 flat return idler sets, 133 mm (5.2 in) rolls
    3. Transition idler sets at 10 and 20 degrees
    4. 20 upper and 20 lower friction self-aligning (training) idler sets
    5. 4 impact idlers at 35 degrees and an impact bed at the loading point
    6. 3 spiral return idler sets and 6 V-return forward-tilt idler sets
    7. Polyurethane H-type cleaner, tungsten carbide P-type cleaner and 2 V-plow cleaners
  5. Take-Up and Structure
    1. Vertical gravity take-up with support frame, counterweight blocks, guard fence and protective grating
    2. 2 head frames, tail frame and intermediate frame, about 998 m (3,274 ft)
    3. 320 support legs, 1200 mm (47.2 in) high
    4. Head chute with liner
    5. Loading chute: 5 x 1500 mm (59.1 in) skirt sections with front curtain, rear baffle and anti-overflow skirt
    6. 3 belt press wheels
    7. Tail guard and snub pulley guard fence
    8. Intermediate frame railing, 500 m (1,640 ft)
    9. Fiberglass rain cover, 3 mm, over about 998 m (3,274 ft)
  6. Safety and Monitoring
    1. 56 two-stage belt misalignment switches
    2. 56 bidirectional pull-cord emergency stop switches with 1,990 m (6,529 ft) of pull cord
    3. Belt speed detection
    4. 2 longitudinal belt tear detectors
    5. Chute blockage detection
    6. Integrated protection unit and 3 signal repeaters
    7. Field devices explosion-proof, with address codes
  7. Electrical and Controls
    1. Master control system per unit: VFD cabinet, automation cabinet and cabling
    2. VFD cabinet: 2 heavy-duty cabinet drives with industrial Ethernet communication and master-slave load sharing
    3. Automation cabinet: PLC with digital and analog input and output modules, 12 in touch-panel HMI, Ethernet switch
    4. Power cable from the distribution room to the main motors (100 m (328 ft) run), with heavy-duty cable tray
    5. Commissioning: about 20 days on site included; travel, accommodation and meals by the buyer
  8. Standards, Packing and Delivery
    1. Design standards: CEMA, DIN
    2. Packing: export seaworthy plywood cases and pallets
    3. Delivery: about 75 to 80 days after deposit and approval of the general arrangement drawing
    4. Warranty: 18 months from delivery or 12 months after commissioning