Description
Overview
Reconditioned Mathis laboratory stenter frame type THS, built 1997, original paint
Continuous range: unwinding, padding, pinning, drying and winding
Fabric width 250 to 550 mm (9.8 to 21.7 in)
Fabric speed 0.2 to 5 m/min (0.7 to 16.4 ft/min)
Maximum temperature 235°C (455°F)
Electric heating 30 kW; supply as built 3 x 400 V + N, 50 Hz
Original controller, original grey / blue color
Compressed air up to 7 bar (100 psi) and a water supply needed
Approximate weight 1,000 kg (2,205 lb)
Unwinding And Infeed
Unwinding device with holding device for the batching roller, follower and clutch
Pneumatic disc brake, maximum batch diameter 400 mm (15.7 in)
Entrance and spreading device
Spreading roller infinitely driven 0 to 400 rpm
Two pneumatically controlled squeezing rollers, rubber covered, for selvedge control
Width adjustment with spindle and hand wheel; device can be opened for cleaning
Squeezing Device (Dyeing And Finishing Padder)
Roller width 650 mm (25.6 in)
Roller diameter 110 mm (4.3 in)
Roller hardness 70° Shore
Pneumatic load adjustment for maximum line pressure 230 N/cm
Liquor trough, content 3.5 liters (0.9 gal), with dipping bow and guiding roller, trough without heating
Outlet valve for trough
Roller for the fabric guiding, finger safety guards
Fabric Guiding, Overfeed And Pinning
Overfeed controller, range up to 40%, post-feed setting also possible, depending on the material
Optical sensing device and two opto electronic edge feelers for the automatic positioning of the pinning-up device
Two fabric guide elements, can be opened, with spreading action; two height adjusting devices
Pinning-up device with brushes: four pre-pinning and two post-pinning brushes, can be opened, with locker
Two pressing down bows, adjustable
Two under feed rolls, rubber covered, as counter rolls, driven
Chain And Width Adjustment
Two guiding rails with pin chains, adjusting device for the rails
Width adjustment by 2 servo motors, automatic optical sensor, push buttons for manual operation
Maximum angle of chain ± 60 mm (2.4 in) at the entrance
Digital indication of fabric width at the entrance
Mechanical width adjustment of the chain by hand wheel at dryer entry and exit, with width indication
Chain wheels, chain tensioners and length compensation
Dryer
Outer box with door, inner box with insulation between the two walls
Removable cover (insulated)
Two exhaust channels with adjusting flaps; exhaust fan at the dryer
Circulation fan, infinitely variable; maximum capacity about 4,000 m3/h (141,000 cu ft/h)
Nozzle box with air flap to adjust air flow top/bottom
Fresh air fan, step switch
Heating 30 kW, over temperature guard
Covers at the dryer entrance and outlet
Two devices for removal of the fabric from the pins with brushes; two safety switches
Control And Instrumentation
Control panel with operating elements and indicating instruments
Electronic control for the 2.2 kW (3 hp) fan motor; air speed adjustable about 6 to 12 m/s (20 to 39 ft/s)
Fan rotation control relay with air speed indicator
Temperature measuring and regulating unit
Heating control in 3 steps, added automatically on request
Digital display of the fabric width at the spreading device
Gear motors, infinitely variable, for the padder and for the pin chain and upwinding device
Motor boxes at entrance and exit, with all motor controllers
Upwinding
Upwinding device with holding device for the batching roller, follower and clutch
Pneumatic adjustable control of the winding tension, maximum batch diameter 400 mm (15.7 in)
Four cones for cardboard tubes 75 to 85 mm (3.0 to 3.3 in)
