Search results for: 'can c'

REFERENCE NUMBER: C-2256 TRUTZSCHLER DK760 40” CANS, YEAR 1995, WITH AUTOMATIC CAN CHANGER DETAILS: MODEL: DK760 YEAR: 1995 CARD COMMANDER CONTROLS 40" CANS WITH AUTOMATIC CAN CHANGER KH850/900 AUTOLEVELER FBK533 CHUTE FEED 460 VOLT/60HZ CURRENTLY INSTALLED AND RUNNING IN FACTORY QUANTITY AVAILABLE: 35 Learn More

M-6262 RF SYSTEMS TD-85 RADIO FREQUENCY DRYER FOR CONES YEAR 2002

RADIO FREQUENCY DRYER FOR CONES
MAKE: RF SYSTEMS
MODEL: TD-85 (K85)
YEAR: 2002
THREE PHASES 380 – 50 HZ
FOR DIFFERENT VOLTAGE THE MACHINE IS EQUIPPED WITH AUTO TRANSFORMER
THE NOMINAL VOLTAGE SHOULD BE WITHIN 5% (TEMPORARY EXCURSIONS OF +5% AND -5% ARE PERMITTED) OTHERWISE CUSTOMER MUST INSTALL A SUITABLE STABILIZER
MAXIMUM POWER ABSORBED FROM THE MAINS: 130 KVA
MAXIMUM CURRENT ABSORBED: 210 A
GAUGE WIRE: 3x75mm2 + GROUND 50mm2 MINIMUM

GENERATOR
MAXIMUM POWER RADIO FREQUENCY GENERATOR: 85 KW (1 x 85KW)
WORK FREQUENCY: 27 MHZ
COOLING SYSTEM: FORCED AIR
MAXIMUM ROOM TEMPERATURE: TA = 35°C IF HIGHER POWER MUST BE REDUCED
MAXIMUM EXHAUST AIR TEMPERATURE: TU = 85°C
OSCILLATOR: CAVITY TYPE WITH HIGH OVERALL EFFICIENCY
FREQUENCY STABILITY: WITHIN LIMITS
RADIATED FIELD: WITHIN LIMITS
GRID CURRENT WITH NO LOAD: 2.3 A TO 2.5 A
GRID CURRENT MINIMUM WITH FULL LOAD: 1.4 A
TRIODE TYPE: RS 3060 CL
FILAMENT TRIODE VOLTAGE: 10 V + 1% - 3%

BELT – CONVEYOR
MATERIAL: POLYESTER FABRIC
TRACKING: AUTOMATIC
LENGTH: 21600mm
WIDTH: 1750mm
RANGE OF CONVEYOR SPEED: 0 TO 50 M/ORA
ELECTRODE: STANDARD TYPE

PRODUCTIVITY
MAXIMUM EVAPORATING CAPACITY: 90 KG WATER PER HOUR

DIMENSIONS
LENGTH: 9600mm
WIDTH: 2124mm
MAXIMUM HEIGHT: 3400mm
GALLERY LENGTH: 4000mm
INLET LENGTH: 2800mm
OUTLET LENGTH: 2800mm
BELT WIDTH: 1750mm
LOAD HEIGHT: 900mm
MAXIMUM HEIGHT OF INLET TRAP: 300mm

THE DRYER TD85 IS COMPOSED OF ONE UNITY OF 85 KW

SPECIAL REQUIREMENTS ON USING RADIO FREQUENCY DRYER
THE DRYER CAN ACCEPT ONLY HYDROEXTRACT GOODS WITH EVEN MOISTURE CONTENT
POSSIBLE FIRE HAZARD WHEN DEALING WITH UNEXTRACTED PACKAGES
PROPEN HYDROEXTRACTION IS IMPORTANT PRIOR TO RF DRYER
LOAD PRODUCT WITH SAME DIMENSIONS AND SIMILAR MOISTURE CONTENTS
PACKAGE PLACEMENT ON THE BELT. ANY TYPE OF TUBE MAY BE USED IN A CONTINUED RF DRYER
METAL TUBES REQUIRE MOVE CARE IN PLACEMENT ON THE BELT THEN PLASTIC TUBE
METAL TUBES CAN CAUSE SHORT CIRCUITY, OR ARCING, FROM ONE ELECTRODE TO GROUND, WHICH CAN DAMAGE THE BELT OR CAUSE FIRE
PACKAGE WITH METAL TUBES MUST BE PLACED ON THE BELT SO THE METAL IS PARALLEL TO THE ELECTRODES AS SHONS IS TY
THE CONVEYOR SHOULD ALWAYS BE LOADED EVENLY, WITH NO BIG EMPTY GAPS
LOAD AS MUCH AS YOU CAN
GOOD WITH DIFFERENTS SIZE ARE NOT ALLOWED THEY CAN GET BURNS
LOAD A QUANTITY OF GOODS WITH A QUANTITY OF WATER TO REMOVE PER LINEAR METER OF BELT AROUND 5 TO 15 KG PER LINEAR METER OF BELT
THE MACHINE CANNOT ACCEPT METALLIC DYSTUFF (EX.CHROME)
DO NOT ENTER METALLIC PARTS
METALLIC IN THE GALLERY CAUSES ELECTRICAL DISCHARGES WHICH MAY THOROUGHLY RUIN BELT AND SET THE DRYING MATERIAL ON FIRE

QUANTITY: 1

Learn More

REFERENCE NUMBER: K-9326 BABCOCK WIDE TENTER FRAME 144" (3657mm) QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: V-0046 AUTOMATIC ROLL SHRINK PACKING MACHINE MODEL ARPM-240I QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4863 (1111HCMTXX10) L THIES TRD-III JET DYEING MACHINE YEAR 2013 THIES TRD III JET DYEING MACHINE BOUGHT NEW IN APRIL 2013 USED APPROXIMATELY 15 TIMES 2 TUBES, BUT YOU CAN CLOSE ONE TUBE AND RUN ONE TUBE IF SMALLER BATCH IS NEEDED 150 KGS PER PORT , TOTAL FOR THE MACHINE 300 TO 330 KGS ONE STOCK TANK TWO SIDE TANKS ORGATEX SOFTWARE, YOU CAN PROGRAM THE MACHINE FROM YOUR COMPUTER AND NETWORK THE MACHINE TO THIS COMPUTER AND TRANSFER FILES FROM THE COMPUTER TO THE MACHINE AND VICE VERSA QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: L-5110

COMPLETE HANK DYEING AND MERCERIZING PLANT

 

QUANTITY: 1

Learn More

REFERENCE NUMBER:   G-8230

HIGH-TEMPERETURE AND HIGH-PRESSURE YARN DYEING MACHINE 40KG

 

DESIGNED FOR DYEING, BOILING OFF, BLEACHING, AND WATER WASHING, ETC. SUITABLE FOR HANK YARN, BOBBIN OR RAW STOCK FIBER

 

MACHINE TYPE: VERTICAL CYLINDER

VAT DIAMETER: Ф600mm

CONE QUANTITY: 7 X 7 = 49 CONES

WORKING TEMPERATURE: 130C

MAX WORKING PRESSURE: 0.4MPA

BOTH RATIO: 1:7 TO 9

WITH COMPUTERIZED CONTROL SYSTEM

HEAT EXCHANGING: COIL TYPE HEAT EXCHANGER, WHICH CAN BE USED FOR EITHER HEATING OR COOLING.

HEAT EXCHANGING SPEED: WHEN THE HEATED STEAM PRESSURE IS 0.4MPA, 40MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BARREL RAISING FROM 20^OC TO 130^OC. WHEN THE COOLING WATER PRESSURE IS 0. 3MPA AND THE WATER TEMPERATURE IS 20 ^OC, 40 MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BECK TO LOWER FROM 130^OC TO 80^OC.

RECYCLING OF DYEING LIQUID: THE POSITIVE AND NEGATIVE RECYCLING OF DYEING LIQUID WILL BE ADJUSTED BY THE CYLINDER THROUGH THE SWITCHING DEVICE INSIDE THE CENTRIFUGAL PUMP.

SEALING OF BOILER: RUBBER ADHESIVE

THE WORKING PRESSURE INSIDE THE TANK WILL MAKE THE RUBBER SEAL CLOSELY TO ATTACH THE FLANGE. THE CONICAL SURFACE OF THE TANK MOUTH IS TO ENHANCE THE SEALING.

OPENING OF TANK COVER: FIRST OPEN THE AIR VALVE TO RELEASE THE PRESSURE INSIDE THE BOILER. WAIT UNTIL NO EXHAUSTED AIR GOING THRU THE EXHAUST VALVE AND THE READING OF PRESSURE GAUGE IS ZERO, WITHDRAW THE WRENCH HANDLE, OPEN THE CLAMPING HOOP TO REMOVE THE FLANGE; AND THEN OPEN THE COVER WITH DRAG WEIGHT. THE COVER WILL BE CLOSED.

 

CONFIGURATION:

1. ELECTRICAL CABINET: STAINLESS STEEL CABINET, PLASTIC COATING

2. ELECTRICAL COMPONENTS: SIEMENS, OMRON

3. COMPUTER: HG COMPUTER (MADE IN CHINA)

4. ELECTROMAGNETIC VALVE: TAIWAN YADEKE

5. PUMP: CENTRIFUGAL PUMP

6. MOTOR: WANNAN MOTOR

7. TEMPERATURE CONTROL: COMPUTER CONTROL, WITH HEATING, COOLING, KEEPING WARM, ETC. FUNCTION.

8. HEAT EXCHANGER: INTERNAL COIL HEATING

9. VALVE: STAINLESS ANGLE VALVES, PNEUMATIC BUTTERFLY VALVES

10. ONE CARRIER BASKET

11. MACHINE BODY MATERIAL: STAINLESS STEEL, 316 LITERS

12. ACCESSORIES: SEAL RING FOR DYE VAT, SEAL FOR MAIN PUMP, SEAL FOR REVERSING SHAFT

 

QUANTITY: 1

Learn More

TT-8579 FABRIC BEAM DYEING MACHINE, WIDTH 1500mm 1. FABRIC BEAM DYEING WINDER MACHINE 2. FABRIC TYPE WOVEN TYRICOT OR SATIN FABRIC 3. FABRIC WIDTH 1500mm 4. BEAM WIDTH 2000mm (MAX.) Learn More

TT-6867 THIES ECO-SOFT PLUS JET DYING MACHINE, 2 TONNE, YEAR 2007 1. BRAND: THIES 2. THIES ECO-SOFT PLUS 3. TYPE: 140/4-DS/PL QUANTITY: 1 Learn More

TT-6339 COMPLETE PLANT FOR MODERN DENIM DYEING & FINISHING, YEAR 2004 Learn More