Search results for: 'Feed'

P-4891 MONFORTS SANFORIZER YEAR 1990 to 1991 WIDTH 1800mm

MONFORTS
SANFORIZER
YEAR: 1990 to 1991
WORKING WIDTH: 1800mm
ROLLER WIDTH: 2000mm
HIGH ENTRY FEEDING UNIT TYPE E+A COMBI
E/L SELVEDGE UNCURLERS KF2020
GUIDE ROLLER STAINLESS STEEL
WEKO HUMIDIFICATION DEVICE BY ROTATING SPRAY DISC
STEAMING CYLINDER, DIAMETER 800mm
TENTER
LENGTH 1500mm
CLIP CHAIN
WIDTH CONTROL
SEMIAUTOMATIC CALANDER ROLLER
RUBBER
ROLLER WIDTH 1650mm
INCLUDING NEW RUBBER BLANKET
1780mm WIDTH
FELT CALANDER WITH DRYING CYLINDER 1500/800mm
ROLLER WIDTH 1900mm (FELT BLANKET 1740mm)
COOLING CYLINDER
DELIVERY TO BIG BATCHER OR PLAITER
SHRINKAGE CONTROL

QUANTITY: 1

Learn More

P-4140 OSTHOFF ST80 GAS SINGEING MACHINE YEAR 1990 WIDTH 1800mm

OSTHOFF
TYPE: ST80
GAS SINGEING MACHINE
YEAR: 1990
WORKING WIDTH: 1800mm
ROLLER WIDTH: 1800mm
CONSISTING OF:
BEATING AND BRUSHING UNIT WITH FILTER FEED KF10
SINGEING UNIT WITH 2 BURNERS
BEATING AND BRUSHING UNIT
TYPE: V899
YEAR: 2001
DESIZING THROUGH WITH 5m CAPACITY
SQUEEZER MENZEL
BIG BATCHER
THE MACHINE WAS COMPLETELY OVERHAULED IN 2001 AND AT THE SAME TIME IT WAS EQUIPPED WITH A THREE-PHASE MOTOR

QUANTITY: 1

Learn More

REFERENCE NUMBER: M-4327

BENNINGER ZELL SIZING MACHINE MODEL BEN-SIZETEC WORKING WIDTH 2200mm YEAR 1994

 

BENNINGER ZELL SIZING MACHINE  MODEL BEN - SIZETEC WORKING WIDTH 2200 mm

YEAR  1994, WITH SECTIONAL AND FRACTIONAL SYSTEM.

N° A13715

MODEL  BB-S/ZT4/4/TKD

1 SECTIONAL BEAM UNROLLING DEVICE MODEL SWA WITH LOADING CELL FOR MEASURING

THE OUT GOING TENSION .

ELECTRO PNEUMATIC BREAKING SYSTEM

MAXIMUM BEAM DIAMETER 1000 mm.

1 FRACTIONAL BEAMING UNROLLING DEVICE WITH CAPACITY UP TO 20 POSITIONS

ELECTRO PNEUMATIC BREAKING SYSTEM

1 SIZING BOX MODEL TDK WORKING WIDTH 2200 mm. TOTAL WIDTH 2400 mm

STAINLESS STEEL BOX WITH TOTAL CAPACITY OF 240 LITERS WITH DIRECT STEAM INJECTION

LOWER VESSELS WITH INDIRECT HEAT SYSTEM

AUTOMATIC SIZE BOX FEEDING

HANDYMAT FOR START AND STOP AND MACHINE REGULATION

1 DRYING SECTION DEVICE MODEL ZT8 – WORKING WIDTH 2200 mm

6 DRYING STAINLESS STEEL CYLINDERS COVERED WITH TEFLON + 2 CYLINDERS WITHOUT TEFLON

4 ELECTRONIC TEMPERATURE REGULATIONS

2 AIR EXTRACTION

1 OIL/GREASE APPLICATION DEVICE MODEL CV

1 YARN SPLITTING DEVICE

7 RODS FOR SECTIONAL BEAMS

19 RODS FOR FRACTIONAL BEAMS

1 HUMIDITY MAHLO CONTROL DEVICE MODEL RMS-7S N°1670/1/10597

1 BEAM ROLLING DEVICE MODEL BB FOR BEAMS UP TO 1000 mm DIAMETER

YARN TRACTION MADE UP OF 3 ROLLS

1 PRESSURIZED ROLLER DEVICE

TENSION AND PRESSURE MEASURE DEVICES

AUTOMATIC BEAM LIFT DEVICE INCLUSIVE OF ADAPTORS FOR DIFFERENT BEAMS

EXTENSION REED FOR ENDS WIDTH CONTROL

MIRROR FOR EASY YARN CONTROL

1 HANDYMAT FOR START AND STOP AND MACHINE REGULATION

1 DUST SUCTION DEVICE

1 COMPLETE SIZE KITCHEN PREPARATION INCLUDING 2 TANKS FOR SIZE STORAGE

1 FULLY AUTOMATIC BENSIZETEC PROCESS CONTROL DEVICE INCLUDING HARDWARE AND SOFTWARE

1 EXTERNAL ELECTRIC CABINET.

Learn More

REFERENCE NUMBER: C-2256 TRUTZSCHLER DK760 40” CANS, YEAR 1995, WITH AUTOMATIC CAN CHANGER DETAILS: MODEL: DK760 YEAR: 1995 CARD COMMANDER CONTROLS 40" CANS WITH AUTOMATIC CAN CHANGER KH850/900 AUTOLEVELER FBK533 CHUTE FEED 460 VOLT/60HZ CURRENTLY INSTALLED AND RUNNING IN FACTORY QUANTITY AVAILABLE: 35 Learn More

REFERENCE NUMBER: K-4610 ROLL CUTTER EQUIPPED WITH: MOVEABLE CUTTING ASSEMBLY IN-CEILING WITH DOUBLE FLWHEEL FOR ADJUSTING AND LOCKING. ADJUSTING SWING THE MEASURE TO MAKE CUTS ACCURATE AND UNIFORM. LOCKING LEVER TISSUE WHICH GREATLY FACILITATES THE CUTTING OF REELS OF SMALL SIZE. SECURITY COMMAND FOR ROTATING ROLLERS MOUNTED DIRECTLY ON THE BLADE LEVER. CUT ROLLS UP TO A LENGTH OF 3.50 METERS. DISK DIAMETER 500mm HIGH RESISTANCE. AUTOMATIC COOLING OF THE BLADE. DOUBLE SHARPENING PNEUMATIC HIGH SPEED WITH CONE WHEEL ACTING ON BOTH SIDES OF OBTAINING A SHARP BLAST. QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-3674 (880WUREXX7) L SANTEX TENTER YEAR 1997-PIN CHAIN -6 ZONES QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: V-0046 AUTOMATIC ROLL SHRINK PACKING MACHINE MODEL ARPM-240I QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: C-1171 MEZZERA + RAMALLUMIN CONTINUOUS WASHING LINE, YEAR 2000, WIDTH 3600mm SPECIFICATIONS: MEZZERA + RAMALLUMIN CONTINUOUS WASHING LINE IN OPEN WIDTH FOR WOVEN FABRIC ROLLERS WIDTH: 3800 MM WORKING WIDTH: 3600 MM YOC: 2000 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-0713 MONFORT STENTER MACHINE YEAR 2005 WIDTH 3200mm MONFORT STENTER MACHINE YEAR 2005 ROLLER WIDTH 3400mm WORKING WIDTH 3200mm TYPE HORIZONTAL PIN CLIP CHAIN ENTRY 3MT 8 CHAMBER HEAT OF SOURCES THERMO OIL ENTRY J SCRAY PADER MANGLE 2 BOWL MAHLO WEFTSTRAIGHTNER ENTRY AND EXIT ARTHOMET CONTROL MACHINE WITH EVAKE SYSTEM OVER FEEDING BRUSHING TWIN EAT HEAT COMBURSHAN SYSTEM MACHINE EXIT SIDE J.SCRAY FOLDER BOOK BATCHER SYSTEM QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: K-9125 BIELLA SHRUNK PROCESS DECATIZER YEAR 1997 WIDTH 1800mm BIELLA SHRUNK PROCESS DECATIZER YEAR: 1997 TYPE: VULCANO WIDTH: 1800mm QUANTITY AVAILABLE: 1 Learn More