Search results for: 'system　装置'

M-5615 KUSTERS WASH RANGE- 120” FACE (3048mm)

KUSTERS WASH RANGE CONSISTING OF THE FOLLOWING:
(3) X KUSTER HORIZONTAL WASHERS, 120” FACE WIDTH, TYPE 225.74-172
(3) X KUSTER NIP SETS 120” FACE RUBBER / STAINLESS STEEL WITH 7.5-HP DC MOTORS
(1) X NASH VACUUM SYSTEM 120” SLOT, 30 HP MOTOR, TRAP AND SILENCER
(16) X MORRISON DRY CAN, 2-STACKS OF 8 CANS EACH, 120” WIDE, 7.5 HP DC MOTORS
(1) X COOPER A-FRAME WINDER 132” WIDE

QUANTITY: 1

L-1212 CIBITEX SANFORIZER 2400mm YEAR 1992 RENEWED IN 2016

SANFORIZING MACHINE
MAKE: CIBITEX
YEAR: 1992
COMPLETELY RENEWED IN 2016
WIDTH: 2400mm

COMPONENTS OF THE MACHINE:
ENTRY
ROLLS OPENER
CENTRALIZER
STEAMER
UNIT SHRINKAGE
COOLING SYSTEM
NON-STOP WITH INSPECTION

QUANTITY: 1

J-0098 TUBETEX KNITGOODS DRYER 3200mm YEAR 2003

MODEL ULTRA 3-ACTIVE PASS
WIDTH 3200mm
YEAR 2003
5 SECTION
PLEVA EXHAUST SYSTEM
FABRIC TEMPERATURE CONTROL
AUTOMATIC LINT CLEANING AND COLLECTION

QUANTITY: 1

P-4929 ICOMATEX STENTER YEAR 1990 WIDTH 3200mm 5 CHAMBERS

ICOMATEX
STENTER
YEAR: 1990
WIDTH: 3200mm
5 CHAMBERS
GAS
VERTICAL CHAIN WITH PINS
PADDER
MANUAL WEFTSTRIAGHTNER
STEAMER AT THE ENTRANCE
GLUEING SYSTEM FOR THE SELVEDGES
COOLING TO THE EXIT
CUT SELVEDGE
EXIT BY SMALL ROLL AND BOOK

QUANTITY: 1

P-4844 ICOMATEX STENTER YEAR 1990 WIDTH 3200mm 5 CHAMBERS

ICOMATEX
STENTER
YEAR: 1990
WIDTH: 3200mm
5 CHAMBERS
GAS
VERTICAL CHAIN WITH PINS
PADDER
MANUAL WEFTSTRAIGHTNER
STEAMER AT THE ENTRANCE
GLUEING SYSTEM FOR THE SELVEDGES
COOLING TO THE EXIT
CUT SELVEDGE
EXIT BY SMALL ROLL AND BOOK

QUANTITY: 1

S-1167 SEALING AND SHRINKING MACHINE, WIDTH 850mm

SEALING AND SHRINKING MACHINE
SHRINKING CANS, BEERS, PURE WATER ETC
SHRUNK BY PE FILM, PVC, POF ETC.
CONVEYING BELT CAN BE MADE OF ROLLERS
OR TEFLON MESH BELT
OR S/S MESH BELT
STAINLESS STEEL HEATER
LARGE POWER FAN SYSTEM
AND SUPER COOLING SYSTEM TO ENSURE
THE EXCELLENT SHRINKING
ITEM 001
MAX PACKING SIZE (MM): L500 X W300 X H350
MIN PACKING SIZE (MM): 280 X 100 X 100
PACKING SPEED: 6 TO 10PCS/MINUTE
VOLTAGE: 220V/50HZ
RATED POWER: 1.8KW
SEALING TIME/SHRINK TIME/TEMPERATURE: 0.5-1.5S/0-0.6S/0 -250 °C
WIDTH/THICKNESS OF THE FILM: 600mm/0.04 -0.12mm
DIMENSION: L1030 X W850 X H970mm
GROSS WEIGHT: 350 KGS
AIR PRESSURE OF WORKING: 4 TO 8MPA
SHRINK FILM: PE POF PVC

QUANTITY: 1

ITEM 002
MAX PACKING SIZE (MM): W600*H400*L
PACKING SPEED: 15M/MIN
VOLTAGE: 380V/50HZ
RATED POWER: 20KW
DIMENSION: L3200 × W850 × H1580mm
GROSS WEIGHT: 380 KGS
SHRINK FILM: PE POF PVC

QUANTITY: 1

L-1154  INTES DYEING JIGGER WIDTH 3400 X 1500mm

ROLLER WIDTH: 3400mm
MAX. LOAD 1500mm (DEPENDS ON FABRIC WEIGHT)
CONTROL SYSTEM: HWS 021

QUANTITY: 2

P-4879 KRANTZ STENTER YEAR 1989 WIDTH 2200mm 5 CHAMBERS

KRANTZ
STENTER
YEAR: 1989 (COMPLETELY REFURBISHED 2006)
WORKING WIDTH: 2200mm
ENTRY FROM TROLLEY OR A-FRAME
BIANCO INFEED UNIT, YEAR 2006

QUANTITY: 1

REFERENCE NUMBER:   G-8230

HIGH-TEMPERETURE AND HIGH-PRESSURE YARN DYEING MACHINE 40KG

DESIGNED FOR DYEING, BOILING OFF, BLEACHING, AND WATER WASHING, ETC. SUITABLE FOR HANK YARN, BOBBIN OR RAW STOCK FIBER

MACHINE TYPE: VERTICAL CYLINDER

VAT DIAMETER: Ф600mm

CONE QUANTITY: 7 X 7 = 49 CONES

WORKING TEMPERATURE: 130C

MAX WORKING PRESSURE: 0.4MPA

BOTH RATIO: 1:7 TO 9

WITH COMPUTERIZED CONTROL SYSTEM

HEAT EXCHANGING: COIL TYPE HEAT EXCHANGER, WHICH CAN BE USED FOR EITHER HEATING OR COOLING.

HEAT EXCHANGING SPEED: WHEN THE HEATED STEAM PRESSURE IS 0.4MPA, 40MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BARREL RAISING FROM 20^OC TO 130^OC. WHEN THE COOLING WATER PRESSURE IS 0. 3MPA AND THE WATER TEMPERATURE IS 20 ^OC, 40 MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BECK TO LOWER FROM 130^OC TO 80^OC.

RECYCLING OF DYEING LIQUID: THE POSITIVE AND NEGATIVE RECYCLING OF DYEING LIQUID WILL BE ADJUSTED BY THE CYLINDER THROUGH THE SWITCHING DEVICE INSIDE THE CENTRIFUGAL PUMP.

SEALING OF BOILER: RUBBER ADHESIVE

THE WORKING PRESSURE INSIDE THE TANK WILL MAKE THE RUBBER SEAL CLOSELY TO ATTACH THE FLANGE. THE CONICAL SURFACE OF THE TANK MOUTH IS TO ENHANCE THE SEALING.

OPENING OF TANK COVER: FIRST OPEN THE AIR VALVE TO RELEASE THE PRESSURE INSIDE THE BOILER. WAIT UNTIL NO EXHAUSTED AIR GOING THRU THE EXHAUST VALVE AND THE READING OF PRESSURE GAUGE IS ZERO, WITHDRAW THE WRENCH HANDLE, OPEN THE CLAMPING HOOP TO REMOVE THE FLANGE; AND THEN OPEN THE COVER WITH DRAG WEIGHT. THE COVER WILL BE CLOSED.

CONFIGURATION:

1. ELECTRICAL CABINET: STAINLESS STEEL CABINET, PLASTIC COATING

2. ELECTRICAL COMPONENTS: SIEMENS, OMRON

3. COMPUTER: HG COMPUTER (MADE IN CHINA)

4. ELECTROMAGNETIC VALVE: TAIWAN YADEKE

5. PUMP: CENTRIFUGAL PUMP

6. MOTOR: WANNAN MOTOR

7. TEMPERATURE CONTROL: COMPUTER CONTROL, WITH HEATING, COOLING, KEEPING WARM, ETC. FUNCTION.

8. HEAT EXCHANGER: INTERNAL COIL HEATING

9. VALVE: STAINLESS ANGLE VALVES, PNEUMATIC BUTTERFLY VALVES

10. ONE CARRIER BASKET

11. MACHINE BODY MATERIAL: STAINLESS STEEL, 316 LITERS

12. ACCESSORIES: SEAL RING FOR DYE VAT, SEAL FOR MAIN PUMP, SEAL FOR REVERSING SHAFT

QUANTITY: 1