Search results for: 'Dry ca'

R-7198 SALVADE RELAX DRYER MACHINE, WORKING WIDTH 2400mm, YEAR 1995 – FOR KNITS

BRAND: SALVADE S.P.A. ITALY
MODEL: AVA
YEAR: 1995
WORKING WIDTH: 2400mm
TYPE: TWO PASSAGES OF KNITS, KNITS INPUT AND OUTPUT ON ONE SIDE (OPEN DRYER MACHINE)
GAS HEATING, TWO GAS BURNERS ITAS, MODEL: 84 A TBH
GAS BURNERS CAPACITY MAX.: 522 KW, 440,000 KCAL/H
SWITCHBOARD AND ELECTRICAL MOTORS: 380V, 50 HZ

QUANTITY: 1

Learn More

M-6262 RF SYSTEMS TD-85 RADIO FREQUENCY DRYER FOR CONES YEAR 2002

RADIO FREQUENCY DRYER FOR CONES
MAKE: RF SYSTEMS
MODEL: TD-85 (K85)
YEAR: 2002
THREE PHASES 380 – 50 HZ
FOR DIFFERENT VOLTAGE THE MACHINE IS EQUIPPED WITH AUTO TRANSFORMER
THE NOMINAL VOLTAGE SHOULD BE WITHIN 5% (TEMPORARY EXCURSIONS OF +5% AND -5% ARE PERMITTED) OTHERWISE CUSTOMER MUST INSTALL A SUITABLE STABILIZER
MAXIMUM POWER ABSORBED FROM THE MAINS: 130 KVA
MAXIMUM CURRENT ABSORBED: 210 A
GAUGE WIRE: 3x75mm2 + GROUND 50mm2 MINIMUM

GENERATOR
MAXIMUM POWER RADIO FREQUENCY GENERATOR: 85 KW (1 x 85KW)
WORK FREQUENCY: 27 MHZ
COOLING SYSTEM: FORCED AIR
MAXIMUM ROOM TEMPERATURE: TA = 35°C IF HIGHER POWER MUST BE REDUCED
MAXIMUM EXHAUST AIR TEMPERATURE: TU = 85°C
OSCILLATOR: CAVITY TYPE WITH HIGH OVERALL EFFICIENCY
FREQUENCY STABILITY: WITHIN LIMITS
RADIATED FIELD: WITHIN LIMITS
GRID CURRENT WITH NO LOAD: 2.3 A TO 2.5 A
GRID CURRENT MINIMUM WITH FULL LOAD: 1.4 A
TRIODE TYPE: RS 3060 CL
FILAMENT TRIODE VOLTAGE: 10 V + 1% - 3%

BELT – CONVEYOR
MATERIAL: POLYESTER FABRIC
TRACKING: AUTOMATIC
LENGTH: 21600mm
WIDTH: 1750mm
RANGE OF CONVEYOR SPEED: 0 TO 50 M/ORA
ELECTRODE: STANDARD TYPE

PRODUCTIVITY
MAXIMUM EVAPORATING CAPACITY: 90 KG WATER PER HOUR

DIMENSIONS
LENGTH: 9600mm
WIDTH: 2124mm
MAXIMUM HEIGHT: 3400mm
GALLERY LENGTH: 4000mm
INLET LENGTH: 2800mm
OUTLET LENGTH: 2800mm
BELT WIDTH: 1750mm
LOAD HEIGHT: 900mm
MAXIMUM HEIGHT OF INLET TRAP: 300mm

THE DRYER TD85 IS COMPOSED OF ONE UNITY OF 85 KW

SPECIAL REQUIREMENTS ON USING RADIO FREQUENCY DRYER
THE DRYER CAN ACCEPT ONLY HYDROEXTRACT GOODS WITH EVEN MOISTURE CONTENT
POSSIBLE FIRE HAZARD WHEN DEALING WITH UNEXTRACTED PACKAGES
PROPEN HYDROEXTRACTION IS IMPORTANT PRIOR TO RF DRYER
LOAD PRODUCT WITH SAME DIMENSIONS AND SIMILAR MOISTURE CONTENTS
PACKAGE PLACEMENT ON THE BELT. ANY TYPE OF TUBE MAY BE USED IN A CONTINUED RF DRYER
METAL TUBES REQUIRE MOVE CARE IN PLACEMENT ON THE BELT THEN PLASTIC TUBE
METAL TUBES CAN CAUSE SHORT CIRCUITY, OR ARCING, FROM ONE ELECTRODE TO GROUND, WHICH CAN DAMAGE THE BELT OR CAUSE FIRE
PACKAGE WITH METAL TUBES MUST BE PLACED ON THE BELT SO THE METAL IS PARALLEL TO THE ELECTRODES AS SHONS IS TY
THE CONVEYOR SHOULD ALWAYS BE LOADED EVENLY, WITH NO BIG EMPTY GAPS
LOAD AS MUCH AS YOU CAN
GOOD WITH DIFFERENTS SIZE ARE NOT ALLOWED THEY CAN GET BURNS
LOAD A QUANTITY OF GOODS WITH A QUANTITY OF WATER TO REMOVE PER LINEAR METER OF BELT AROUND 5 TO 15 KG PER LINEAR METER OF BELT
THE MACHINE CANNOT ACCEPT METALLIC DYSTUFF (EX.CHROME)
DO NOT ENTER METALLIC PARTS
METALLIC IN THE GALLERY CAUSES ELECTRICAL DISCHARGES WHICH MAY THOROUGHLY RUIN BELT AND SET THE DRYING MATERIAL ON FIRE

QUANTITY: 1

Learn More

REFERENCE NUMBER: M-5136 (1212PZWKHH11) L COMPLETE PACKAGE DYE HOUSE 3 PRESSURE DRYERS 13 HIGH TEMPERATURE CONE DYEING MACHINES 3 LABORATORY HIGH TEMPERATURE DYEING MACHINES 2 LABORATORY HIGH TEMPERATURE DYEING MACHINES 1 COLOUR TESTER 1 LABORATORY DYEING MACHINE 1 LABORATORY HIGH TEMPERATURE CONE DYEING MACHINE 1 CONE CENTRIFUGE 1 WASHING TESTER 2 DRYING OVENS 2 COLOUR TESTER 1 CROCKTESTER QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: J-2640
DYEING AND FINISHING PLANT FOR SALE

ITEM 001
THIES SAMPLE DYEING MACHINE
MODEL: MINISOFT SAMPLE
CAPACITY: 50 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 002
THIES DYEING MACHINE
MODEL ECOSOFT PLUS
3 PORT SPLIT/SPLIT
CAPACITY: 900 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 003
THIES DYEING MACHINE
MODEL: ECOSOFT PLUS
2 PORT SPLIT/SPLIT
CAPACITY: 600 KGS
YEAR: 1999
MICROPROCESSOR CONTROL
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 004
THIES DYEING MACHINE
MODEL ECOSOFT PLUS
1 PORT SPLIT/SPLIT
CAPACITY: 300 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: A460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 005
GASTON COUNTY DYEING MACHINE
MODEL: AQUAFLOW
2 PORT
CAPACITY; 250 KGS
YEAR: 1987
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING AND UNLOADING REEL
QUANTITY: 1

ITEM 006
THIES DYEING MACHINE
MODEL: SOFT TRD
2 TUBE
CAPACITY: 700 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 007 (also our J-2647)
LAFER OPEN WIDTH COMPACTOR MACHINE
MODEL: KSA 500 2400/2200
YEAR: 1998
LAFER TEXEN CONTROLS
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION BAR ENTRY TO LATTICE ROLL GUIDER
• OPERATOR’S PLATFORM
• PUP TENTER WITH KNIT ENTRY, VERTICAL PIN CHAIN, WITH PLATE GUIDES, RAIL OPENING, PINNING BRUSHES, PINS ONLY, WITH SUPPORT SECTION FOR THE FABRIC IN THE CENTER, AT 10’ THERE IS A STEAMING SECTION, TOTAL LENGTH OF THE TENTER IS 30’, WITH AUTOMATIC LUBRICATION FOR THE CHAIN
• KSA 500 COMPACTOR BENCH WITH TEXEN CONTROLS
• TENSIONLESS FABRIC CONVEYOR
• PLAITOR AND FABRIC SCRAY WITH OPTICAL LOAD SENSOR
• INLINE INSPECTION BATCHER MACHINE, WITHH A BACK LIGHTED BOARD, MANUAL CUT
• SCALE TO WEIGHT THE FABRIC
QUANTITY: 1

ITEM 008 (also our J-2648)
SANTEX TUBULAR 4-ROLL EXTRACTION PAD
MODEL: SANTASTRETCH PLUS 140
YEAR: 1998
COMPOSED OF TURNTABLE, DETWISTER, TUBULAR 4-ROLL PAD WITH WET SPREADERS, PLAITOR
WITH ADDITION TANKS FOR SOFTENER
REEL FABRIC PLAITOR EXIT
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

ITEM 009
SANTEX CONVEYOR DRYER FOR OPEN WIDTH AND TUBULAR FABRIC
MODEL: SANTASHRINK 4/5240
YEAR: 1998
SANTEX CONTROLS
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION BAR ENTRY TO LATTICE ROLL GUIDER TO
• (2) SANTEX 2-ROLL PADS, RUBBER OVER RUBBER, 102” WIDE x 12” DIAMETER, STAINLESS STEEL PAN, 10-TON PAD, SWING-AWAY PAN, TENSION BAR WITH 2 STAINLESS STEEL MIXING TANKS, 75 GALLONS EACH
• DRIVEN SCROLL ROLLS WITH EDGE GUIDE CONTROL, WIDTH 95”
• OPERATOR’S PLATFORM
• PUP TENTER WITH KNIT ENTRY 45°, YEAR 1998, VERTICAL PIN CHAIN, 30’ LONG WITH TANDEMATIC PLATE GUIDES, RAIL GUIDES, PINNING BRUSHES, GUIDE SUPPORT FOR THE FABRIC, FABRIC CONVEYOR TO ENTER BOTH TUBULAR OR OPEN WIDTH FABRIC TO
• CONVEYOR DRYER 100” WIDE, 5 ZONES, 3-PASS WITH MAXON BURNERS, 5 CIRCULATING FANS TO CONVEYOR BELT TO PLAITOR
• ALL MOTORS AND SANTEX CONTROLS AND MONITORS
QUANTITY: 1

ITEM 010
SANTEX AG TUBULAR COMPACTOR MACHINE
MODEL: SANTASPREAD 140
YEAR: 1998
SANTEX CONTROLS
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSIONS BAR ENTRY
• OPERATOR’S PLATFORM
• TENSION DEVICE
• DRIVEN SPREADER BARS
• STEAMING DEVICE
• TUBULAR COMPACTING BENCH
• FELT BLANKET ONTO THE CONVEYOR BELT
• PRECISION PLAITOR
• TABELTOP ELECTRONIC SCALE
QUANTITY: 1

ITEM 011
COMET NAPPER
MODEL: PEGSO-X4
YEAR: 1998
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
24 ROLLS WITH TURNING BARS FOR TUBULAR 90” WIDE
XYCOM CONTROLS
12-BAG COLLECTION SYSTEM AND PLAITOR
YEAR: 1996
QUANTITY: 1

ITEM 012
STENTEX TENTER FRAME
MODEL: STENTOTHERM 3300
YEAR: 1999
STENTEX CONTROLS
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION ENTRY TO TEXT-STAR TYPE GUIDER TO 2 ROLL PAD
• ADDITION TANK TOP SCRAY PAD TO TEXT-STAR TYPE GUIDER
• TWO ROLL PAD R/R 10 TON
• OPERATOR’S PLATFORM
• WORKING WIDTH 1800mm
• HORIZONTAL PIN CHAIN, KNIT ENTRY
• TANDEMATIC SPLITLEVEL DECURLERS
• OVERFEED
• PINNING BRUSHES
• STEAM BOX
• RAIL GUIDERS, 20 FEET ENTRY, 8 ZONES
• 80 FEET HOUSING
• SCREEN MONITORS
• GAS FIRED, MAXON OVEPAK 408 BURNERS
• HONEYWELL CONTROLS
• 3 FEET COOLING ZONE
• 2 COOLING CANS, SELVEDGE TRIMMERS
• PLIATOR, SCRAY
• ZONE IN LINE INSPECTION BATCHER
QUANTITY: 1

ITEM 013
ZIMMER ROTARY SCREEN PRINTING MACHINE
MODEL: R92-S153
YEAR: 1993
COMPOSED OF:
• TENSION BAR SKY ENTRY
• SCRAY
• CORINO BRUSH
• CORINO PRINT GUIDER
• ZIMMER PRINTER, 8 COLOR, 86” BLANEKT
• PRINT CONVEYOR DRYER, 30’ LONG, 3-ZONE, GAS FIRED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

ITEM 014
SAFETY SWITCH BULLET NOSE SLITTER
MODEL: CUTTING
WITH REEL FABRIC PLIATOR
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

Learn More

REFERENCE NUMBER: M-5347 (220MKSFXX1) L LORIS BELLINI YARN DYEING PLANT 1 SCHARER SCHWEITER METTLER 06 SSM HIGH SPEED CROSS WINDER AG SWITZERLAND (MODEL PSM 51 WITH 288 SPINDLES) 1 CAMEL ROBOT ITALY 02 COMPLETE SET OF TRACKS AND ROBOTICS QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M- 3405 (880160LMW7RM) K KUSTERS THERMOSOL DYEING MACHINE YEAR 1993 WIDTH 1800mm KUSTERS THERMOSOL DYEING MACHINE YEAR 1993 - TOTAL WIDTH 1800mm - FABRIC WIDTH 1600 mm - INITIAL DRYER 3 SECTIONS – ELECTRIC HEATING - DRYER 3 SECTIONS – STEAM HEATED ( 5 BARS) - THERMOSOL 2 SECTIONS – GAS HEATED QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: A-1224 (0101GHBXX12) A GALVANIN DRYER FOR BOBBINS YEAR 2002 GALVANIN DRYER FOR BOBBINS YEAR: 2002 QUANTITY AVAILABLE: 1 Learn More

TT-2173 KUESTERS COLD DYEING PADDER MACHINES, WORKING WIDTH 1800mm KUESTERS COLD DYEING PADDER MACHINES BRAND: KUESTERS QUANTITY: 2 Learn More

REFERENCE NUMBER: L-5110

COMPLETE HANK DYEING AND MERCERIZING PLANT

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: M-4327

BENNINGER ZELL SIZING MACHINE MODEL BEN-SIZETEC WORKING WIDTH 2200mm YEAR 1994

 

BENNINGER ZELL SIZING MACHINE  MODEL BEN - SIZETEC WORKING WIDTH 2200 mm

YEAR  1994, WITH SECTIONAL AND FRACTIONAL SYSTEM.

N° A13715

MODEL  BB-S/ZT4/4/TKD

1 SECTIONAL BEAM UNROLLING DEVICE MODEL SWA WITH LOADING CELL FOR MEASURING

THE OUT GOING TENSION .

ELECTRO PNEUMATIC BREAKING SYSTEM

MAXIMUM BEAM DIAMETER 1000 mm.

1 FRACTIONAL BEAMING UNROLLING DEVICE WITH CAPACITY UP TO 20 POSITIONS

ELECTRO PNEUMATIC BREAKING SYSTEM

1 SIZING BOX MODEL TDK WORKING WIDTH 2200 mm. TOTAL WIDTH 2400 mm

STAINLESS STEEL BOX WITH TOTAL CAPACITY OF 240 LITERS WITH DIRECT STEAM INJECTION

LOWER VESSELS WITH INDIRECT HEAT SYSTEM

AUTOMATIC SIZE BOX FEEDING

HANDYMAT FOR START AND STOP AND MACHINE REGULATION

1 DRYING SECTION DEVICE MODEL ZT8 – WORKING WIDTH 2200 mm

6 DRYING STAINLESS STEEL CYLINDERS COVERED WITH TEFLON + 2 CYLINDERS WITHOUT TEFLON

4 ELECTRONIC TEMPERATURE REGULATIONS

2 AIR EXTRACTION

1 OIL/GREASE APPLICATION DEVICE MODEL CV

1 YARN SPLITTING DEVICE

7 RODS FOR SECTIONAL BEAMS

19 RODS FOR FRACTIONAL BEAMS

1 HUMIDITY MAHLO CONTROL DEVICE MODEL RMS-7S N°1670/1/10597

1 BEAM ROLLING DEVICE MODEL BB FOR BEAMS UP TO 1000 mm DIAMETER

YARN TRACTION MADE UP OF 3 ROLLS

1 PRESSURIZED ROLLER DEVICE

TENSION AND PRESSURE MEASURE DEVICES

AUTOMATIC BEAM LIFT DEVICE INCLUSIVE OF ADAPTORS FOR DIFFERENT BEAMS

EXTENSION REED FOR ENDS WIDTH CONTROL

MIRROR FOR EASY YARN CONTROL

1 HANDYMAT FOR START AND STOP AND MACHINE REGULATION

1 DUST SUCTION DEVICE

1 COMPLETE SIZE KITCHEN PREPARATION INCLUDING 2 TANKS FOR SIZE STORAGE

1 FULLY AUTOMATIC BENSIZETEC PROCESS CONTROL DEVICE INCLUDING HARDWARE AND SOFTWARE

1 EXTERNAL ELECTRIC CABINET.

Learn More