Search results for: 'Function'

REFERENCE NUMBER: T-3396 BIRCH BROTHERS INSPECTION STATIONS, ROLL WIDTH 84”, CLOTH WIDTH 80”, YEAR 1994 BIRCH BROTHERS INSPECTION STATIONS ROLL WIDTH: 84” CLOTH WIDTH: 80” YEAR 1994 LIGHTED INSPECTION BOARD TRUE METER MEASURING SYSTEM MERROW SEWING MACHINE ON RAILS ASSISTED DOFF FUNCTION AND CONNECTING CONVEYOR SYSTEM QUANTITY: 4 Learn More

REFERENCE NUMBER:   G-8230

HIGH-TEMPERETURE AND HIGH-PRESSURE YARN DYEING MACHINE 40KG

 

DESIGNED FOR DYEING, BOILING OFF, BLEACHING, AND WATER WASHING, ETC. SUITABLE FOR HANK YARN, BOBBIN OR RAW STOCK FIBER

 

MACHINE TYPE: VERTICAL CYLINDER

VAT DIAMETER: Ф600mm

CONE QUANTITY: 7 X 7 = 49 CONES

WORKING TEMPERATURE: 130C

MAX WORKING PRESSURE: 0.4MPA

BOTH RATIO: 1:7 TO 9

WITH COMPUTERIZED CONTROL SYSTEM

HEAT EXCHANGING: COIL TYPE HEAT EXCHANGER, WHICH CAN BE USED FOR EITHER HEATING OR COOLING.

HEAT EXCHANGING SPEED: WHEN THE HEATED STEAM PRESSURE IS 0.4MPA, 40MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BARREL RAISING FROM 20^OC TO 130^OC. WHEN THE COOLING WATER PRESSURE IS 0. 3MPA AND THE WATER TEMPERATURE IS 20 ^OC, 40 MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BECK TO LOWER FROM 130^OC TO 80^OC.

RECYCLING OF DYEING LIQUID: THE POSITIVE AND NEGATIVE RECYCLING OF DYEING LIQUID WILL BE ADJUSTED BY THE CYLINDER THROUGH THE SWITCHING DEVICE INSIDE THE CENTRIFUGAL PUMP.

SEALING OF BOILER: RUBBER ADHESIVE

THE WORKING PRESSURE INSIDE THE TANK WILL MAKE THE RUBBER SEAL CLOSELY TO ATTACH THE FLANGE. THE CONICAL SURFACE OF THE TANK MOUTH IS TO ENHANCE THE SEALING.

OPENING OF TANK COVER: FIRST OPEN THE AIR VALVE TO RELEASE THE PRESSURE INSIDE THE BOILER. WAIT UNTIL NO EXHAUSTED AIR GOING THRU THE EXHAUST VALVE AND THE READING OF PRESSURE GAUGE IS ZERO, WITHDRAW THE WRENCH HANDLE, OPEN THE CLAMPING HOOP TO REMOVE THE FLANGE; AND THEN OPEN THE COVER WITH DRAG WEIGHT. THE COVER WILL BE CLOSED.

 

CONFIGURATION:

1. ELECTRICAL CABINET: STAINLESS STEEL CABINET, PLASTIC COATING

2. ELECTRICAL COMPONENTS: SIEMENS, OMRON

3. COMPUTER: HG COMPUTER (MADE IN CHINA)

4. ELECTROMAGNETIC VALVE: TAIWAN YADEKE

5. PUMP: CENTRIFUGAL PUMP

6. MOTOR: WANNAN MOTOR

7. TEMPERATURE CONTROL: COMPUTER CONTROL, WITH HEATING, COOLING, KEEPING WARM, ETC. FUNCTION.

8. HEAT EXCHANGER: INTERNAL COIL HEATING

9. VALVE: STAINLESS ANGLE VALVES, PNEUMATIC BUTTERFLY VALVES

10. ONE CARRIER BASKET

11. MACHINE BODY MATERIAL: STAINLESS STEEL, 316 LITERS

12. ACCESSORIES: SEAL RING FOR DYE VAT, SEAL FOR MAIN PUMP, SEAL FOR REVERSING SHAFT

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: P-1813 BRAZZOLI H.T. SATURNO LUFT HTF DYEING MACHINE YEAR 2002 400KG BRAZZOLI MODEL: H.T. DYEING MACHINE TYPE: SATURNO LUFT HTF FOR TERRY TOWEL FABRICS YEAR: 2002 CAPACITY: 400 KILOGRAMS EACH MACHINE TEHSE MACHINES CAN ALSO BE OPERATED COUPLED TO DYE ONE LOT OF 800 KILOGRAMS SUPPLIED WITH MAIN MOTOR AND PUMP AUTOMATIC VALVES FOR STEAM AND WATER FUNCTIONS ADD TANK + DOSING PUMP ELECTRICAL PANEL WITH MICROPROCESSOR CONTROLS TEST RUN POSSIBLE, SINCE THE UNITS ARE STILL FULLY CONNECTED TO THE ELECTRICITY, STEAM, WATER, ETC QUANTITY AVAILABLE: 2 Learn More

REFERENCE NUMBER: M-4863 (1111HCMTXX10) L THIES TRD-III JET DYEING MACHINE YEAR 2013 THIES TRD III JET DYEING MACHINE BOUGHT NEW IN APRIL 2013 USED APPROXIMATELY 15 TIMES 2 TUBES, BUT YOU CAN CLOSE ONE TUBE AND RUN ONE TUBE IF SMALLER BATCH IS NEEDED 150 KGS PER PORT , TOTAL FOR THE MACHINE 300 TO 330 KGS ONE STOCK TANK TWO SIDE TANKS ORGATEX SOFTWARE, YOU CAN PROGRAM THE MACHINE FROM YOUR COMPUTER AND NETWORK THE MACHINE TO THIS COMPUTER AND TRANSFER FILES FROM THE COMPUTER TO THE MACHINE AND VICE VERSA QUANTITY AVAILABLE: 1 Learn More