Search results for: 'year'

REFERENCE NUMBER: M-3984

RING SPINNING

 

(1) TRUTZSCHLER BLENDOMAT BDT 019, YEAR 1990

(1) TRUTZSCHLER BLENDER GBRA 1000, YEAR 1990

(1) TRUTZSCHLER AXIFLOW AFC, YEAR 1990

(1) TRUTZSCHLER MULTIMIXER MPM8/1400, YEAR 1990

(1) TRUTZSCHLER SEPAROMAT ASTA 800, YEAR 1990

(2) TRUTZSCHLER SILO BEB 1200, YEAR 1990

(2) TRUTZSCHLER FIBER OPENER RST, YEAR 1990

(5) TRUTZSCHLER CONDENSER LVSA, YEAR 1990

(4) TRUTZSCHLER FAN TV 425, YEAR 1990

(2) TRUTZSCHLER FAN TVF 425, YEAR 1990

(3) TRUTZSCHLER FAN TV 500, YEAR 1990

(1) TRUTZSCHLER FAN TVK 650, YEAR 1990

(3) TRUTZSCHLER FILTER SFV 123, YEAR 1990

(1) TRUTZSCHLER FILTER SFF 3, YEAR 1990

(3) TRUTZSCHLER CYCLON ANB AT, YEAR 1990

(1) TRUTZSCHLER FEED TABLE (OPENING) M30 S/C, YEAR 1990

(2) TRUTZSCHLER FEED TABLE (FILTER) S/N S/C, YEAR 1990

(1) TRUTZSCHLER FEED TABLE (CARDS), YEAR 1990

(14) TRUTZSCHLER CHUTE FEED FBK 533, YEAR 1990

 

(5) RIETER DRAW FRAME SB2, CAN SIZE 1000x1200mm, YEAR 1997

(2) RIETER DRAW FRAME RSB D30, CAN SIZE 500x1000mm, YEAR 1999

(3) RIETER DRAW FRAME RSB 951, CAN SIZE 600x1200mm, YEAR 1997

 

(2) ZINSER/HARA LAP FORMER 820, 20 POSITIONS, 1000x1040mm, YEAR 1990

(12) ZINSER/HARA COMBER 830, CAN SIZE 500x1200mm, YEAR 1990

(1) ELECTRONIC CLEANER PANEL, YEAR 1990

 

(5) ZINSER ROVING FRAME 660, 120 POSITIONS, 16x6, CAN SIZE 500x1000mm, YEAR 1990.

(3) SOHLER AIRTEX OVERHEAD BLOWER SP 88 ZB, YEAR 1990

 

(20) ZINSER RING FRAME 321E, 1000 SPINDLES, RING DIA 45mm, GAUGE 75mm, YEAR 1990

(10) SOHLER AIRTEX OVERHEAD BLOWER AP 88 ZZ WI, YEAR 1990

(1) SUCTION FAN, YEAR 1990

 

(4) MURATA WINDER 7 II (MACH CONER), 60 POSITIONS, WITH LUWA OVERHEAD BLOWER, YEAR 1990

 

(1) XORELLA STEAMER CONTEXXOR, YEAR 1990

Learn More

REFERENCE NUMBER: M-5301 (1313THWKXX12) L VAMATEX TERRY TOWEL WEAVING FACTORY YEAR 1995-2003 TERRY TOWEL FACTORY WEAVING DEPARTMENT VAMATEX 1151 ES 3600mm WORKING WIDTH, WITH DOBBY (3) X YEAR 1996 (1) X YEAR 2000 (2) X YEAR 1999 (2) X YEAR 1997 (2) X YEAR 1995 5 SETS WITH 16 HEALD FRAMES, 20 SHAFTS 5 SETS WITH 12 HEALD FRAMES, 16 SHAFTS FACTORY ONCE SELLS WHOLE WITH DOBBY LOT AS ABOVE THEN THEY WILL SELL LOOMS WITH JACQUARDS (6) X VAMATEX LEONARDO YEAR 2003 WITH JACQUARDS J5 STAUBLI 2688 JACQUARD WORKING WIDTH 2600mm (4) X VAMATEX LEONARDO YEAR 2003 WITH VRT SYSTEM/JACQUARD J5 STAUBLI 2688 JACQUARD WORKING WIDTH 2600mm (4) X VAMATEX LEONARDO YEAR 2003 WITH JUMBO JACQUARD J5 STAUBLI 6144 JACQUARD WORKING WIDTH 2600mm (2) X VAMATEX LEONARDO YEAR 2003 WITH GROSS JACQUARD 6144 JACQUARD WORKING WIDTH 2600mm TOTAL QUANTITY: 26 LOOMS Learn More

LIST NUMBER: L-3004
SIZING MACHINES FOR SALE

REFERENCE NUMBER: C-5212
BENNINGER SIZING MACHINE
TYPE BEN SIZETEC
YOM: 2004
WORKING WIDTH: 2400mm
BENINGER DIRECT WARPER
TYPE BEN DIRECT
YOM: 2005
WORKING WIDTH: 2400mm
QUANTITY: 1

REFERENCE NUMBER: P-4682
BENNINGER
SIZING MACHINE
YEAR: 2002
WIDTH: 2800mm
QUANTITY: 1 SET

REFERENCE NUMBER: P-7130
SUCKER MULLER
TYPE: HACOBA
SIZING MACHINE
YEAR: 1999
WORKING WIDTH: 1800mm
QUANTITY: 1

REFERENCE NUMBER: C-3650
OFFER 001
SUCKER MOENUS Z 14 SIZING MACHINE
WIDTH: 3400mm
YEAR: 2006
QUANTITY: 1
OFFER 002
BENNINGER BEN DIRECT WARPING MACHINE
YEAR: 2005
WIDTH: 2200mm
QUANTITY: 1

REFERENCE NUMBER: A-1197 (1212GHBXX11) A
MAKE: BENNINGER
MODEL: BEN SIZETEC
YEAR: 1998
Width - 2000mm
QUANTITY: 2

REFERENCE NUMBER: P-6712
SUCKER MULLER
SIZING MACHINE
YEAR: 2003
HEADSTOCK WIDTH: 3600mm
QUANTITY: 1

REFERENCE NUMBER: M-5040
(1 SET) BENNINGER SIZING MACHINES (SLASHERS), YEAR 2000

REFERENCE NUMBER: R-3746
ITEM 001
KARL MAYER​ DIRECT WARPING ​MACHINE
YEAR: 20​06​
WIDTH: 2​0​00mm
​QUANTITY: 1 SET
ITEM 002
KARL MAYER SIZING MACHINE
YEAR: 2011
QUANTITY: 1 SET

Learn More

V-1042 RIETER SPINNING PLANT OF ABOUT 20,500 SPINDLES

01 X RIETER A10 UNIFLOC, YEAR 1998, LENGTH 38 METERS
01 X RIETER B2/5 WASTE FEEDER, YEAR 1998
01 X RIETER B11 UNICLEAN, YEAR 1998
01 X RIETER B7/3 UNIMIX, YEAR 1998
01 X RIETER B60 UNIMIX, YEAR 1998
02 X JOSSI FOREIGN FIBER DETECTORS, ED-33-1200-1 YEAR 2002
02 X RIETER A20+A21 CONDENSER, YEAR 2002
01 X RIETER B11 UNICLEAN, YEAR 2002
01 X RIETER B7/3 UNIMIX, YEAR 2002
01 X RIETER B60 UNIMIX, YEAR 2002

06 X RIETER C51 CARDS, YEAR 1998
11 X RIETER C51 CARDS, YEAR 2002
AUTOMATIC COILER
CAN SIZE: 600 MM X 1200 MM

02 X RIETER SB-D10 DRAW FRAMES, YEAR 1998
02 X RIETER RSB-D30 DRAW FRAMES, YEAR 1998
03 X RIETER SB-D15 DRAW FRAMES, YEAR 2002
04 X RIETER RSB-D35 DRAW FRAMES, YEAR 2002

01 X RIETER E32 UNILAP, YEAR 2002
05 X RIETER E62 COMBERS, YEAR 2002
01 X KAIGON UNILAP 2, YEAR 2012
06 X RIETER E7/5 COMBERS, YEAR 1987

04 X RIETER F10 ROVING FRAMES, YEAR 1998, 120 POSITIONS
03 X RIETER F11 ROVING FRAMES, YEAR 2002, 144 POSITIONS

08 X RIETER G33 RING FRAMES, YEAR 1998, 1104 SPINDLES, DIAM. 42 MM, GAUGE 70 MM, TUBES 210 MM, DRAFTINGS P3-1
10 X RIETER G33 RING FRAMES, YEAR 2002, 1200 SPINDLES, DIAM. 40 MM, GAUGE 70 MM, TUBES 200 MM, DRAFTINGS P3-1

04 X SCHLAFHORST AC 238 WINDERS, YEAR 1998, 60 SPINDLES
04 X MURATA 21F MURATEC WINDERS, YEAR 2002, 60 SPINDLES
AUTOMATIC FEEDING
USTER QUANTUM IMK-C20-F20 CLEARERS
5.57 CONICITY
WAXING

Learn More

REFERENCE  NUMBER:  G-0784

RIETER FDY  EXTRUSION EQUIPMENT FOR POLYPROPYLENE YEAR 1996/98

 

1. Machine m26/39:

Year 1996

For 1 fdy spinning line with 2+4 positions, each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  800 mm

Spinning pump capacity:  4x10 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  670 mm

Quench length:  1700 mm

Number of spin-finish pumps per position:  1

Capacity of spin-finish pump:  4x0.05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

Extruder for 4 positions Year 1998:

 

1 extruder type e1. 105-30m:

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  105 mm

-l/d ratio:  30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 58 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 95kw

-extruder frame

 

1 extruder measuring head, dowtherm vapour heated

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

Extruder for 2 positions Year 1998:

1 extruder type e1. 60-30

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  60 mm

-l/d ratio:  30

-barrel with

                electrical ceramic heaters

                6 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 17 kw

                inlet zone, water cooled

                insulation

-screw nitrited with maddock mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated year 1998

-measuring head comprising:

                insulation

Double pt100, one each for melt and dowtherm vapour temperature

                                pressure sensors for melt pressure

                burst disc for power switch-off at overpressure.

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam year 1998

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 25 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled level gauge

- vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

-max pressure in the spinpack:  350 bar

-design temperature:  320 °c

-spinneret outside dimensions:  95 mm

-bottom loading design

-bayonet locking, insert and tighten by turning 90°

-self sealing system

-sand or metal powder filtration, 3 cm filling depth

-wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 6 ccm/rev

Each spin pump system comprising

Individual drive motor with flange connection to the reduction gear

Hollow gear shaft for installation of spin pump shaft

Shaft with shear pin protection

Reduction ratio 1:80

Pump speed:  8-30 rev/min

Motor type:  synchronous ac-motor

Rated power:  500w at 50 cps

 

Quench air cabinets bsk 670/1700:

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                4 spin finish application nozzles

                1 yarn cutter / aspirator unit

                1 spin finish pump

                4 centring yarn guides

                4 intermingling units

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls year 1998:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speed range:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60 hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ±0.2 mm

Tube outside diameter:  106 ±0.4 mm

Tube length:  225 ±0.5 mm

 

Oil-mist lubrication unit:

Compressed air distribution station

Mobile aspirator guns with hoses

Electrical control equipment

-for electrical power

                general:  3 x 380v/50hz plus ground wire

                euro-standard:  3x400v 50 or 60hz plus ground wire

                maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation:  ±2%

 

Process control system (cif):

                fully integrated control system to control and monitor the entire spinning line.

                the central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control year 1998:

 

Spinning section:

Speed adjustment for the extruder motor is done via a dc-convertor

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor. While current flows, a voltage is inducted into the

Rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

2. Machines m27/ 28 / 30 year 1998:

For 3 fdy spinning lines each with 2 positions, and each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  1000 mm

Spinning pump capacity:  4x7.5 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  470 mm

Quench length:  1200 mm

Number of spin-finish pumps per position:  2

Capacity of spin-finish pump:  4x0.16 ccm/rev + 4x0,05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

 

1 extruder type e1. 60-30m

-nominal extruder capacity:  max 80 kg/h for pp

-screw diameter:  65 mm

-l/d ratio: 30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 22 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated:

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated:

Melt distribution system comprising:

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam:

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 18 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled

-level gauge

-vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

Max pressure in the spinpack:  350 bar

Design temperature:  320 °c

Spinneret outside dimensions:  95 mm

Bottom loading design

Bayonet locking, insert and tighten by turning 90°

Self sealing system

Sand or metal powder filtration, 3 cm filling depth

Wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 7.5 ccm/rev

Each spin pump system comprising

                individual drive motor with flange connection to the reduction gear

                hollow gear shaft for installation of spin pump shaft

                shaft with shear pin protection

                reduction ratio:  1:80

                pump speed:  8-30 rev/min

                motor type:  synchronous ac-motor

                rated power:  500w at 50 cps

 

Quench air cabinets bsk 470/1200

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                2 spin finish application nozzles per end

                1 yarn cutter / aspirator unit

                2 spin finish pump

                4 centring yarn guides

                4 pre-intermingling jets

                4 intermingling units

                1 additional operator panel between duo1 and duo 2.

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speedrange:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60

Hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094:

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ± 0.2 mm

Tube outside diameter:  106 ± 0.4 mm

Tube length:  225 ± 0.5 mm

 

Compressed air distribution station:

Mobile aspirator guns with hoses

Electrical control equipment

For electrical power

                general : 3 x 380v/50hz plus ground wire

Euro-standard: 3x400v 50 or 60hz plus ground wire

Maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation: ±2%

 

Process control system (cif):

Fully integrated control system to control and monitor the entire spinning line.

The central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control:

Spinning section.

Speed adjustment for the extruder motor is done via a dc-convertor.

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor.

While current flows, a voltage is inducted into the rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

HOURLY PRODUCTION:

FOR 150 DENIER @ 3500 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 3.5 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 14 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 28 KG/HOUR AND M39 = 56 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 28 KG/HOUR EACH.

(AS PER OUR PEOPLE AT THE EXTRUSION PLANT, THEY WERE RUNNING TRIALS TO PRODUCE THE 150 DENIER @ 4000 MPM WINDER SPEED)

 

FOR 300 DENIER @ 3600 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 7.2 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 28.8 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 57.6 KG/HOUR AND M39 = 115.2 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 57.6 KG/HOUR EACH.

 

FOR 600 DENIER @ 2200 MPM WINDER SPEED, (SPEED LIMITATION DUE TO EXTRUDER CAPACITY) THE HOURLY PRODUCTION IS 8.8 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 35.2 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 70.4 KG/HOUR AND M39 = 140.8 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 70.4 KG/HOUR EACH.

 

MACHINE HAS BEEN PARTIALLY DISASSEMBLED (EXTRUDERS AND SPINBEAMS HAVE BEEN TAKEN DOWN TO GROUNDFLOOR) REST OF THE EQUIPMENT STILL TO BE DISASSEMBLED

Learn More

REFERENCE NUMBER: M-3381

COMPLETE YARN DYEING PLANT FONGS YEAR 2006

 

50 KG CAPACITY FONGS YARN DYEING MACHINE , 2006 YEAR

 

200 KG CAPACITY FONGS YARN DYEING MACHINE , 2006 YEAR

 

300 KG CAPACITY FONGS YARN DYEING MACHINE , 2006 YEAR

 

400 KG CAPACITY FONGS YARN DYEING MACHINE , 2006 YEAR

 

RD-200 FONGS YARN DRYER MACHINE , 2006 YEAR

 

YARN CENTRUFUGAL SQUEEZING MACHINE , 1996 YEAR

 

2 X 60 HEAT SOFT PRO CONE WINDING MACHINE , 2006 YEAR ( TOTAL 120 HEAT )

 

4 X 60 HEAT FINAL PRO CONE WINDING MACHINE , 2006 YEAR ( TOTAL 240 HEAT )

Learn More

REFERENCE NUMBER: L-6069

EASTMAN STATIC TABLE CUTTING MACHINE MODEL M9000, 20’ X 72’, YEAR 2009

 

STATIC TABLE CUTTING MACHINE

MAKE: EASTMAN

MODEL: M9000

20 FEET LONG X 72 FEET WIDE

PURCHASED IN YEAR 2009

220 VOLT, 1 PHASE

 

QUANTITY: 1

Learn More

C-3985 COMPLETE CFS AQUARIUS BALL LOLLIPOP LINE, YEAR 2004 TO 2006

OFFER 001
COMPLETE CFS AQUARIUS BALL LOLLIPOP LINE
YEAR: 2004 TO 2006

OFFER 002
KLOCKNER HANSEL PROCESSING BATCH ROLLER
YEAR: 2006

OFFER 003
KLOCKNER HANSEL PROCESSING ROPE SIZER
YEAR: 2006

OFFER 004
CFS AQUARIUS B.V. BALL FORMER 1000
YEAR: 2005

OFFER 005
CFS AQUARIUS CONVEYOR BELT
YEAR: 2004

OFFER 006
LOLLIPOP COOLER B
YEAR: 2005

OFFER 007
CFS AQUARIUS B.V. BUNCH WRAPPER 600
YEAR: 2005

QUANTITY: 1 LINE

Learn More

REFERENCE NUMBER: K-2346 ZINSER RING SPINNING PLANT 23,240 SPINDLES YEAR 1993 TO 2003 CONSISTS OF: 3 BALE OPENERS, YEAR 1993 TRUTZSCHLER COTTON AND BLENDS BLOWROOM, YEAR 1993 8 TRUTZSCHLER DK903 CARDS, YEAR 2003 8 TRUTZSCHLER DK760 CARDS YEAR 1993 2 RIETER SB 851 DRAW FRAMES 3 RIETER SB2 DRAW FRAMES 5 RIETER RSB 851 DRAW FRAMES 3 ZINSER 660 ROVING FRAMES, 120 SPINDLES, YEAR 1993 20 ZINSER 321 RING SPINNING FRAMES-1184 SPINDLES, AUTO DOFFING, 42mm RINGS, 5 MURATA CONE WINDERS TYPE 7/5, 60 HEADS, USTER POLYMATIC CLEARERS, CBF STATION, YEAR 1995 3 SCHLAFHORST CONE WINDERS, YEAR 1997, 60 HEADS, USTER POLYMATIC C15 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: C-2257 SUCKER MÜLLER AND KARL MAYER ROTAL SIZING MACHINE COMPRISING OF WARP BEAM UNWINDING CREEL, YEAR: 1985 MODIFIED 2010 DETAILS: MAKER: SUCKER MÜLLER AND KARL MAYER ROTAL YEAR: 1985 YEAR MODIFIED: 2010 QUANTITY AVAILABLE: 1 Learn More