Search results for: 'air+co'

REFERENCE  NUMBER:  G-0784

RIETER FDY  EXTRUSION EQUIPMENT FOR POLYPROPYLENE YEAR 1996/98

 

1. Machine m26/39:

Year 1996

For 1 fdy spinning line with 2+4 positions, each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  800 mm

Spinning pump capacity:  4x10 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  670 mm

Quench length:  1700 mm

Number of spin-finish pumps per position:  1

Capacity of spin-finish pump:  4x0.05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

Extruder for 4 positions Year 1998:

 

1 extruder type e1. 105-30m:

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  105 mm

-l/d ratio:  30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 58 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 95kw

-extruder frame

 

1 extruder measuring head, dowtherm vapour heated

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

Extruder for 2 positions Year 1998:

1 extruder type e1. 60-30

-nominal extruder capacity:  max 275 kg/h for pp

-operational extruder capacity:  max 248 kg/h for pp

-screw diameter:  60 mm

-l/d ratio:  30

-barrel with

                electrical ceramic heaters

                6 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 17 kw

                inlet zone, water cooled

                insulation

-screw nitrited with maddock mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated year 1998

-measuring head comprising:

                insulation

Double pt100, one each for melt and dowtherm vapour temperature

                                pressure sensors for melt pressure

                burst disc for power switch-off at overpressure.

 

1 melt distribution system, dowtherm vapour heated

-melt distribution system comprising

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam year 1998

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 25 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled level gauge

- vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

-max pressure in the spinpack:  350 bar

-design temperature:  320 °c

-spinneret outside dimensions:  95 mm

-bottom loading design

-bayonet locking, insert and tighten by turning 90°

-self sealing system

-sand or metal powder filtration, 3 cm filling depth

-wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 6 ccm/rev

Each spin pump system comprising

Individual drive motor with flange connection to the reduction gear

Hollow gear shaft for installation of spin pump shaft

Shaft with shear pin protection

Reduction ratio 1:80

Pump speed:  8-30 rev/min

Motor type:  synchronous ac-motor

Rated power:  500w at 50 cps

 

Quench air cabinets bsk 670/1700:

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                4 spin finish application nozzles

                1 yarn cutter / aspirator unit

                1 spin finish pump

                4 centring yarn guides

                4 intermingling units

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls year 1998:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speed range:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60 hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ±0.2 mm

Tube outside diameter:  106 ±0.4 mm

Tube length:  225 ±0.5 mm

 

Oil-mist lubrication unit:

Compressed air distribution station

Mobile aspirator guns with hoses

Electrical control equipment

-for electrical power

                general:  3 x 380v/50hz plus ground wire

                euro-standard:  3x400v 50 or 60hz plus ground wire

                maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation:  ±2%

 

Process control system (cif):

                fully integrated control system to control and monitor the entire spinning line.

                the central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control year 1998:

 

Spinning section:

Speed adjustment for the extruder motor is done via a dc-convertor

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor. While current flows, a voltage is inducted into the

Rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

2. Machines m27/ 28 / 30 year 1998:

For 3 fdy spinning lines each with 2 positions, and each position with 4 ends

Product:  fdy-yarn on bobbins

Raw material:  pp, dried filament grade chips

Yarn count range:  150 – 400 dtex

Winder speed for target:  4000 m/min

 

Machine technical data:

Position gauge:  1000 mm

Spinning pump capacity:  4x7.5 ccm/rev

Spinneret size diameter:  95 mm

Quench width:  470 mm

Quench length:  1200 mm

Number of spin-finish pumps per position:  2

Capacity of spin-finish pump:  4x0.16 ccm/rev + 4x0,05 ccm/rev

Number of winders/position:  1

Type of winder:  riemat a6-094

Number of packages/winder:  4

Maximum package diameter:  420 mm

Package stroke:  190 mm

Package weight at 280 mm package diameter:  approx. 6.2 kg

 

Detailed technical specifications:

 

1 extruder type e1. 60-30m

-nominal extruder capacity:  max 80 kg/h for pp

-screw diameter:  65 mm

-l/d ratio: 30

-barrel with:

                electrical ceramic heaters

                7 heating zones, each zone equipped with one 2xpt100

                heating zone capacity approx. 22 kw

                inlet zone, water cooled

                nozzle for nitrogen purge

                insulation

-screw with torpedo mixing head

-reduction gear, including belt transmission to motor

-dc motor, rated power approx. 22kw

-extruder frame

 

1 extruder measuring head, electrically heated:

-measuring head comprising:

                coarse filter

                insulation

-double pt100, one each for melt and dowtherm vapour temperature

-pressure sensors for melt pressure, one in front and one behind the coarse filter

 

1 melt distribution system, dowtherm vapour heated:

Melt distribution system comprising:

                main product pipe between extruder, measuring head and melt distributor.

 

1 riebeam bottom loading spinning beam:

-beam comprising:

                welded-in pump blocks with bolted pump adapter plate

                silumin insulation blocks

                melt distribution pipes with polished inner surfaces

                efficient vapour heating on all sides of spin pumps

                optimized heat condustion to the spinnerets

                1 freezing valve upstream of each spinpump

                2 pressure sensors for measuring the melt pressure in front and behind the spinpump

                (2 per line)

                heating box, completely insulated

                heating by dowtherm vapour

                1 double pt100 for measuring and controlling the heating box temperature

Designed as follows:

-bottom loading of rieter quickfit spinpacks

-design temperature 320°c

-maximum allowable working pressure: 300 bar for melt pipe and 2.57 bar for jacket

 

Dowtherm evaporator and components for heating system:

-electrically heated, total capacity approx 18 kw

-shut-off valves

-drainage valves

-dry protection sensor

-magnetic controlled

-level gauge

-vent system on top of measuring head.

 

Poy spin packs, type rieter quickfit:

Max pressure in the spinpack:  350 bar

Design temperature:  320 °c

Spinneret outside dimensions:  95 mm

Bottom loading design

Bayonet locking, insert and tighten by turning 90°

Self sealing system

Sand or metal powder filtration, 3 cm filling depth

Wire mesh filters

 

Spin pumps with motors and gears:

Gear pumps, 4-fold

Capacity 4 x 7.5 ccm/rev

Each spin pump system comprising

                individual drive motor with flange connection to the reduction gear

                hollow gear shaft for installation of spin pump shaft

                shaft with shear pin protection

                reduction ratio:  1:80

                pump speed:  8-30 rev/min

                motor type:  synchronous ac-motor

                rated power:  500w at 50 cps

 

Quench air cabinets bsk 470/1200

Each cabinet comprising:

-rigid cabinet made from welded sheet metal, painted, side walls made from alu sheet metal

-air rectifier consisting of different layers of perforated metal sheets, rectifiers removable to the front for cleaning.

-1 perforated hinged door

-air inlet duct flanged with counter flange, comprising air flow regulating flaps

-interfloor filament duct, length 2000 mm

-alu chutes for start-up

-nozzles for connection of differential pressure gauge.

 

Spinning vapour exhausts:

-exhaust hood per spinning position for removal of spinning vapour

-hood designed as follows:

                made from stainless steel

                air flow regulation flap

                hood removable for cleaning

 

Take-up frames, type riedraw 1:

Welded steel frame, housing all drawrolls, compressed air supply pipes for the aspirator units and the yarn waste pipes within the fdy take-up unit.

Per position:

                4 inlet yarn guides

                2 spin finish application nozzles per end

                1 yarn cutter / aspirator unit

                2 spin finish pump

                4 centring yarn guides

                4 pre-intermingling jets

                4 intermingling units

                1 additional operator panel between duo1 and duo 2.

                rolls as described further

                1 automatic winder riemat a6-094

 

Drawrolls:

Mono 1 with 1 rievap 32 dual shell drawroll, type j7/32-40, ot40

Speedrange:  750 to 4000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

And 1 bearing separator roll, type srd60

Hard chromium plated

 

Duo 1 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 2 with 2 rievap 32 dual shell drawroll, type j7/32-60, ot40

Speedrange:  1000 to 6000 mpm

Roll diameter:  190 mm

Working width:  250 mm

Temperature range:  45-250°c

 

Duo 3 with 2 cold draw roll units each type j7/45-55

Speedrange:  1800 to 5500 mpm

Roll diameter:  150 mm

Working width:  180 mm

 

Automatic and wasteless winder riemat a6-094:

Spindle driven

Number of ends per winder:  4 ends

Yarn count range:  15 to 1000 dtex

Take up speed:  2500 to 5500 m/min

Chuck length:  900 mm

 

190 mm stroke, 420 mm outside package diameter

Package volume:  24.7 dm³

Tube bore:  94 ± 0.2 mm

Tube outside diameter:  106 ± 0.4 mm

Tube length:  225 ± 0.5 mm

 

Compressed air distribution station:

Mobile aspirator guns with hoses

Electrical control equipment

For electrical power

                general : 3 x 380v/50hz plus ground wire

Euro-standard: 3x400v 50 or 60hz plus ground wire

Maximum voltage variation ±10% measured at terminals of cabinets

                maximum frequency variation: ±2%

 

Process control system (cif):

Fully integrated control system to control and monitor the entire spinning line.

The central monitoring unit si linked to the plc of the spinning section and the plcs of each spinning position.

 

Drive and heater control:

Spinning section.

Speed adjustment for the extruder motor is done via a dc-convertor.

To achieve a constant pressure at the extruder outlet, the output of the pressure controller is transmitted to the dc-converter to adjust the extruder speed.

The feedback of the actual extruder speed is done by a tacho generator mounted on the extruder motor.

One common frequency inverter supplies the synchronous ac motors for the spin pumps.

According to process conditions, the plc transmits the setpoint to the inverter.

All motors are equipped with an overload protection.

Solid state relays heat each extruder zone and spinning beam.

Each extruder zone and the spinning beam represent an independent control loop.

 

Take-up section:

The inverter unit is a processor-controlled static frequency inverter for powering the 3-phase motors.

All inverter units in a position cabinet are supplied with approx 570v dc from a common rectifier.

 

Heating system:

The heating unit rhu is processor-controlled.

The power supply is taken straight from 3-phase 380/400v which powers the cabinet.

The inductor is fitted inside the draw roll.

The rhu switches the current on and off in this inductor.

While current flows, a voltage is inducted into the rotating draw roll.

This sets up a short-circuit current in the draw roll, thereby heating the roll unit.

 

HOURLY PRODUCTION:

FOR 150 DENIER @ 3500 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 3.5 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 14 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 28 KG/HOUR AND M39 = 56 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 28 KG/HOUR EACH.

(AS PER OUR PEOPLE AT THE EXTRUSION PLANT, THEY WERE RUNNING TRIALS TO PRODUCE THE 150 DENIER @ 4000 MPM WINDER SPEED)

 

FOR 300 DENIER @ 3600 MPM WINDER SPEED, THE HOURLY PRODUCTION IS 7.2 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 28.8 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 57.6 KG/HOUR AND M39 = 115.2 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 57.6 KG/HOUR EACH.

 

FOR 600 DENIER @ 2200 MPM WINDER SPEED, (SPEED LIMITATION DUE TO EXTRUDER CAPACITY) THE HOURLY PRODUCTION IS 8.8 KG/BOBBIN.

AS THERE IS 4 ENDS PER POSITION, THIS MEANS 35.2 KG/HOUR/POSITION

M26/39 ARE OF 2 + 4 POSITIONS; HENCE M26 = 70.4 KG/HOUR AND M39 = 140.8 KG/HOUR

M27/28/30 ARE OF 2 POSITIONS EACH, HENCE 70.4 KG/HOUR EACH.

 

MACHINE HAS BEEN PARTIALLY DISASSEMBLED (EXTRUDERS AND SPINBEAMS HAVE BEEN TAKEN DOWN TO GROUNDFLOOR) REST OF THE EQUIPMENT STILL TO BE DISASSEMBLED

Learn More

EFFECTIVE WIDTH: 1600mm
DAILY OUTPUT: 10,000 KGS PER DAY
WEIGHT RANGE: 10 TO 150 GSM
FILAMENT DIAMETER: 1.6 TO 2.0 DENIER
SPEED: 350 TO 400 METERS PER MINUTE
RAW MATERIAL: POLYPROPYLENE (PP)
DIMENSIONS: 35,000 X 15,000 X 11,000mm
VOLTAGE: 380 VOLTS, 3 PHASE

CONSISTING OF:

SPUNBOND EQUIPMENT

PP VACUUM SUCTION MACHINE (2)
7800 TO 900 KGS PER HOUR
AIR CAPACITY: 300 CUBIC METERS PER HOUR
POWER: 7.5 KW

MASTER BATCH DOSING UNIT (2)
ACCURACY: 0.01%

EXTRUDER (2)
DIAMETER: 130mm
SINGLE SCREW (2)
HEATING SYSTEM: ELECTRICITY
MOTOR: 75 KW

MELT FILTRATION MACHINE (2)
PIPE SIZE: 50mm
FILTER AREA: 3.5 SQUARE METERS
MELT FLOW: 650 KGS PER HOUR
DOUBLE FILTRATION CHAMBER

MELTING PUMP (2)
40 RPM
FLOW CAPACITY: 400 KGS PER HOUR
POWER: 7.5 KW

SPINNING BEAM (2)
DIMENSIONS: 1900 X 256mm
HANGER TYPE MELT DISTRIBUTION
HEATING SYSTEM: OIL
WORKING TEMPERATURE: 200 TO 260 CELSIUS

SPINNERET (4)
HARDNESS: 30
SIZE: 1900mm LONG X 256mm WIDE
HOLE DIAMETER 0.45mm
HOLE QUANTITY: 6500 HOLE PER METER

QUENCHING UNIT (2)
WORKING TEMP: 20 CELSIUS
AIR FLOW CAPACITY: 12,000 CUBIC METERS/H
AIR PRESSURE: 6500
FILTER SIZE: 80#

FILAMENT DRAFT UNITS (2)
AIR PRESSURE: 5020PA
AIR FLOW CAPACITY: 12,000 CUBIC METERS/H
INSIDE TEMP: 10 TO 25 CELSIUS
FILAMENT FINENESS: 1.6 TO 2.0 DENIER

MELT BLOWN EQUIPMENT

VACUUM SUCTION MACHINE (2)
LOAD CAPACITY: 700 TO 900 KGS PER HOUR
AIR CAPACITY: 300 CUBIC METERS/H
POWER: 7.5 KW

MASTER BATCH DOSING UNIT (2)
4 HOPPERS
200 KGS HOPPER LOAD

EXTRUDER
DIAMETER: 105mm
SINGLE SCREW
MOTOR: 18.5 KW

MELT FILTER
DOUBLE CYLINDER
HYDRAULIC
MELT FLOW CAPACITY: 450 KGS/HR
FILTER SIZE: 150mm DIAMETER
ELECTRIC HEATING

MELTING PUMP
SPEED: 40 RPM
MELT FLOW CAPACITY: 450 KGS PER HOUR
POWER: 7.5 KW

MELT BLOWN DIE SPINNARET
SPINNERET HOLE SIZE: 0.32 TO 0.35mm
HOLE DISTANCE: 40 TO 42 PER INCH
FABRIC WEIGHT: 2 TO 200 GSM

HIGH PRESSURE AIR BLOWER
AIR FLOW CAPACITY: 70 TO 100 CUBIC METERS PER MINUTE
AIR PRESSURE: 100 KPA
POWER: 200 KW

WEB FORMING MACHINE
SPEED: 100 METERS PER MINUTE

ELECTRIC TREATMENT
VOLTAGE: 220 VOLTS, 50 Hz
INPUT CURRENT: 3A
OUTPUT VOLTAGE: 60 KV
TREAT WEB WIDTH: 1.6 METERS

HOT AIR HEATING MACHINE
WORKING TEMP: 350 CELSIUS
PRESSURE: 0.8 KPA
HEATING: ELECTRIC
POWER: 200 KW

THERMAL CALENDER
PROCESSING SPEED: 400 METERS PER MINUTE
ROLLER SIZE: 2000mm LONG, 520mm DIAMETER
EMBOSSING ROLLER: 1
LINEAR PRESSURE: 30 TO 125 N/mm
HEATING SYSTEM: OIL

HYDROPHILIC MACHINE
SPEED: 400 METERS PER MINUTE
FEEDING SYSTEM: DOUBLE KISSING ROLLER
KISS ROLLER DIAMETER: 215mm
LIQUID TANK: 200 KGS WITH HEAT/WARM AND MIX

DRYING SYSTEM:
INFRARED + HOT AIR
DRIVE ROLL SIZE: 150mm
HEATING EQUIPMENT: QUARTZ HEATER, HOT AIR BLOWER, EXHAUST AIR BLOWER

INSPECTION MACHINE
EFFECTIVE WIDTH: 1600mm
INSPECTION SPEED: 400 METERS PER MINUTE
INSPECT GSM: 10 TO 40 GSM

AUTOMATIC WINDING MACHINE
SPEED: 400 METERS PER MINUTE
ROLLER DIAMETER: 2000mm
ROLLER EXCHANGE SYSTEM: AUTOMATIC
FABRIC INSPECTOR: ONLINE
POWER: 15 KW

HIGH SPEED SLITTING MACHINE
PROCESS SPEED: 800 METERS PER MIN
ROLL DIAMETER: MAX 1500mm
SLITTING WIDTH: 80mm
PAPER TUBE SIZE: 76mm DIAMETER
AUTO TENSILE CONTROL: AVAILABLE ONLINE
METER COUNTING: AVAILABLE ONLINE

OIL HEATER (4)
HEATING POWER: 60 KW
MOTOR POWER: 7.5 KW
OIL PUMP FLOW: 30 CUBIC METERS PER SECOND
PRESSURE: 0.4 KPA

WATER CHILLER
DRIVE SYSTEM: SCREW
COOLING CAPACITY: 300,000 CALORIES
TEMP: 0 TO 20 CELSIUS
POWER: 110 KW

AIR BLOWER
SPEED: 1450 RPM
AIR BLOW CAPACITY: 12,000 CUBIC METERS PER HOUR
PRESSURE: 5200 PA
POWER: 30 KW x 3, 45 KW x 1

AIR COMPRESSOR
DRIVE SYSTEM: SCREW
PRESSURE: 0.8 KPA
POWER: 15 KW

HEATING SYSTEM: ELECTRIC
TEMP: 350 CELSIUS
HEATING TIME: 6 TO 8 HOURS
POWER: 4 KW

ULTRASONIC CLEANING MACHINE
3mm THICK
SIZE: 2000 X 500mm
FREQUENCY VIBRATION: 100 KHZ
TEMP: 40 CELSIUS

ELECTRONIC PANEL BOARD

PLATFORM

Learn More

C-3980 KRAFT PAPER MAKING MACHINE WITH GAS BOILER, CAPACITY 3 TO 5 T/D, NET PAPER WIDTH 1200mm

KRAFT PAPER MAKING MACHINE
WITH GAS BOILER
CAPACITY: 3 TO 5 T/D KRAFT PAPER MACHINE
1092 KRAFT CORRUGATED PAPER MACHINE
WITH RECYCLE PAPER AS RAW MATERIAL
TECHNICAL PARAMETER:
OUTPUT: KRAFT PAPER, CORRUGATED PAPER
WEIGHT: 60 TO 180G/M2
NET PAPER WIDTH: 1200mm

QUANTITY: 1

Learn More

REFERENCE NUMBER: L-5934

MONFORTS 6-F TWIN AIR STENTER YEAR 2003 – WORKING WIDTH 2400mm

 

STENTER

RAMA MONFORTS

MAKE: MONFORTS

MODEL: 6-F TWIN

YEAR: 2003

440 VAC 60HZ

NATURAL GAS

AIR COMPRESSOR 7 BAR

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: T-6550

MEDICAL PROTECTIVE CLOTHING BLOOD SYNTHETIC PENETRABILITY TESTER

 

TECHNICAL SPECIFICATIONS AND CONFIGURATION:

1. THE INSTRUMENT ADOPTS AN AIR SOURCE THAT CAN PROVIDE (0.5 ~ 30±0.1) KPA PRESSURE TO CONTINUOUSLY PRESSURIZED THE SAMPLE, WHICH IS NOT RESTRICTED BY THE SPACE OF THE TEST SITE;

2. THE AIR PRESSURE RANGE CAN BE ADJUSTED FREELY, AND THE ADJUSTMENT RANGE (0.5 ~ 30) KPA;

3. COLOR TOUCH SCREEN DISPLAY AND OPERATION;

4. THE SAMPLE CLAMPING PAD IS PROCESSED WITH IMPORTED SPECIAL ALUMINUM PROFILES, WHICH IS LIGHT IN MATERIAL, CLEAN IN SURFACE AND NEVER RUSTS.

5. THE INSTRUMENT ADOPTS IMPORTED SPECIAL ALUMINUM WIRE DRAWING PANEL, EQUIPPED WITH METAL KEYS, SENSITIVE OPERATION, NOT EASY TO DAMAGE;

6. CLAMPING DEVICE FOR INSTRUMENT SAMPLES, EQUIPPED WITH LOCKING PROTECTION, TO PREVENT THE SYNTHETIC BLOOD FROM SPLASHING AROUND;

7. CLAMPING FORCE IS ACCURATE AND RELIABLE;

8. THE TEST TANK IS EQUIPPED WITH A SPECIAL PLACEMENT DEVICE, WHICH IS CONVENIENT FOR CUSTOMERS TO OPERATE;

9. THE TEST TANK IS PROCESSED WITH SPECIAL 316 STAINLESS STEEL, AND THE TOP IS EQUIPPED WITH A SPECIAL COVER FOR HIGH TRANSPARENT PROTECTION;

10. THE WASHER BELOW THE SAMPLE IS MADE OF HIGH-QUALITY PTFE MATERIAL AFTER SPECIAL PROCESSING;

11. SQUARE METAL BLOCK NET: OPEN SPACE ≥50°%; BENDING ≤5mm AT 30KPA;

12. INSTRUMENT TIME CONTROL ACCURACY ≤01 SECONDS;

13. THE SHELL OF THE INSTRUMENT IS MADE OF HIGH-QUALITY METAL BAKING PAINT, WHICH IS BEAUTIFUL AND GENEROUS.

14. EQUIPPED WITH PRINTER INTERFACE, CONNECTED TO THE PRINTER CAN DIRECTLY PRINT DATA REPORTS.

 

TECHNICAL PARAMETERS:

1. SAMPLE SIZE: 75mm X 75mm

2. TEST AREA: 28.26 SQUARE CENTIMETERS

3. AIR PRESSURE ADJUSTMENT RANGE (0.5 ~ 30) KPA

4. EXTERNAL SIZE: 500mm X 500mm X 500mm (L X W X H)

5. WEIGHT OF THE INSTRUMENT: 40 KG

6. POWER SUPPLY: AC220V, 50HZ,SCOPE OF SUPPLY: 1. ONE MAIN MACHINE; 2. TWO PTFE GASKETS; 3. TWO ORDINARY WASHERS; 4. ONE METAL BLOCKING NET; 5. A SET OF SPECIAL LOCKING TOOLS; 6. ONE HIGH-QUALITY SILENT AIR PUMP, [NOTE: SAFETY PRODUCTION LICENSE IS NOT INCLUDED]. 7. EQUIPPED WITH PRINTER INTERFACE; 8. ONE SAMPLE TEMPLATE; 9. ONE PRODUCT CERTIFICATE; 10. ONE COPY OF PRODUCT OPERATION MANUAL.

 

OPERATION INSTRUCTION:

INSERT THE AIR PUMP OUTPUT PIPE INTO THE OIL AND WATER SEPARATOR OF THE INSTRUMENT AS REQUIRED (PRESSURE 0.1-0.3MPA).

AFTER SWITCHING ON THE POWER, THE STARTUP INTERFACE (NAME OF THE DEVICE) IS DISPLAYED.

PRESS THE "ENTER" BUTTON TO ENTER THE TEST INTERFACE, AS SHOWN IN THE FOLLOWING FIGURE:

CLICK "SETTING” BUTTON, GET INTO PARAMETER SETTING SCREEN, AS BELOW THIS SCREEN CAN SET THE SYSTEM TIME, DATE AND TESTING TIME, AFTER SETTING, CLICK "SAVE” BUTTON TO KEEP THE SETTING DATA. (NOTE: IT REQUIRES 5 MINUTES IN THE STANDARD)

 

QUANTITY: 1

Learn More

See all pictures: https://ibb.co/album/gpK9bF

#1 GRIBETZ MPLUS PATTERN LINK 90 TACK AND JUMP 3 BAR WITH PANEL CUTTER 4 POS CREEL

#2 GRIBETZ GI4300 TACK AND JUMP 90" 3 BAR WITH PANEL CUTTER 3 POS CREEL

# 3 EMCO 2 BAR 1X3 WITH PANEL CUTTER, YEAR 2001 (FOR PARTS)

#4 EMCO COMPUSTITCH 3 BAR
WITH JAMES CASH K-10 PANEL CUTTER

#5 GRIBETZ GI2300 90" SET UP FOR BORDERS 4 POS CREEL

#6 EMCO 9000 COMPUSTITCH 1X3X6 BUT RUNNING 1X6
WITH BORDER CUTTER JAMES CASH K-10 1997

#7 EMCO 9000 COMPUSTITCH 3 BAR 1 POSITION CREEL
WITH BORDER CUTTER JAMES CASH K-10

#8 GRIBETZ 3 BAR 92"
WITH JAMES CASH K-12

#9 TAPE EDGE WITH SINGER 300UX6 STEEL TABLE 55 X 81

#10 ATLANTA ATTACHEMENT TAPE EDGE WITH SINGER 300UX5 WITH STAINLESS STEEL TABLE 60 X 80

#11 ATLANTA ATTACHEMENT TAPE EDGE WITH SINGER 300UX5 WITH STAINLESS STEEL TABLE 60 X 80

#12 ATLANTA ATTACHEMENT TAPE EDGE WITH PFAFF 5625 WITH STAINLESS STEEL TABLE 60 X 80

#13 ATLANTA ATTACHEMENT TAPE EDGE WITH SINGER 300UX6 WITH STAINLESS STEEL TABLE 60 X 80

#14 PORTER TAPE EDGE PFAFF DISSASSEMBLED HEAD TABLE SIZE 60 X 82

#15 ATLANTA ATTACHMENT TAPE EDGE WITH PFAFF 5625 STAINLESS STEEL TABLE 59 X 79

#16 ATLANTA ATTACHEMENT TAPE EDGE WITH SINGERS 300UX5 STAINLESS STEEL TABLE 60 X 80 16"H

#17 BUILD UP TABLES MOSTLY 60 X 80 OF WHICH 15 ARE GLOBAL SYSTEMS AND 2 ARE HOME MADE

#19 ? SMALL BALER CONSOLIDATED MODEL STDS-2 36' WIDE X 18" FRONT TO BACK X 50"H

#20 SCREW UNBALER ATLANTA ATTACHMENT FOR 18 INNERSPRING CAPACITY

#21 PIQUA BALER 58 X 31 X 54" TALL 220 VOLT

#22 SCREW UNBALER WBSCO

#23 CART FOR INNERSPRING BALE

#24 GRIBETZ PANEL CUTTER ( I HAVE ALL THE INFO ALREADY)

#25 LAMINATOR GRIBETZ STRATA WITH HOT ROLL AND FELT BLANDET FOR LAMINATING WITH WEB SUBSTRATE (ROTARY HEAT PRESS) MODEL GLM011 220 VOLT , 2 POS CREEL

#26 HORIZONTAL FOAM CUTTER ESCO MODEL HTX 51-88 PU+
88" WIDE , X 118" LONG , KNIFE GRINDERS , SUCTION TABLE
TOUCH SCREEN PANEL , ELECTRICAL CONTROL PANEL
AUTOMATIC LUBRICATION BINKS MODEL 80-600 SG2 PLUS

#27 VERTICAL FOAM CUTTER MODEL EL-4
112" WIDE
OUTSIDE TABLE 73"
INSIDE TABLE 74"
FENCE 8" PLUS 16 " EXTENSION
68" THROAT
112" OVERALL HEIGHT
194" TOTAL RAIL WIDTH

#28 PORTER SERGER FLANGER MODEL 4000 WITH AIR FLOTATION TABLE
220 VOLT

#29 ATLANTA ATTACHMENT JUKI SERGER FLANGER MODEL MO6916G BELT DRIVE WITH AIR FLOTATION TABLE

#30 ATLANTA ATTACHEMENT JUKI SERGER FLANGER MODEL MO6916G BELT DRIVE WITH AIR FLOTATION TABLE

#31 SINGER LONG ARM REPAIR 25"

#32 ATLANTA ATTACHEMENT RUFFLER
MODEL 13XXMF

#33 ATLANTA ATTATCHMENT 9 NEEDLE SEWING MACHINE (MULTINEEDLE) MODEL 4000D

#34 SINGLE NEEDLE SIT DOWN MACHINES OF WHICH 3 ARE PORTER

#35 AVANCE EMBROIDERY MACHINE

#36 GALKIN "X" SEWING MACHINE FOR HANDLES
GAP5OBT-3 , JUKI MODEL LK1900CV

#37 ATLANTA ATTACHMENT DOUBLE BORDER SERGER 25" OPENING , PEGASUS HEAD
MODEL E521-130 AND EX5203-M03

#38 ATLANTA ATTACHMENT BINDER FOR HANDLE MAKING

#39 ANDERSON MULTISLITTER 10 BLADES 92" WIDE

#40 ANDERSON STAND ALONE PANEL CUTTER 103"WIDE WITH 2 EDGE SLITTERS AND ONE CROSS CUTTER
WITH 1049 HOURS ON THE CLOCK

#41 CONVEYOR FOR SEW DEPARTMENTE 34" WIDE OVER 100 FEET LONG

#42 TOYOTA FORKLIFTS 6270 LBS CAPACITY MODEL 71CCUT5 (TWO)
ONE NISSAN FORKLIFT
ONE CATERPILLAR FORKLIFT

#43 ONE GLUE STATION 4 GUNS , SABA GUNS , NOT THERE (BELONG TO SABA)

#44 240 FEET LONG CONVEYOR FEEDING MATTRESS WRAPPING DEPARTMENT

#45 TWO MERELLO WRAPPERS 20 INCH MAX HEIGHT X 88 " WIDE, YEAR 2016

#46 TECNOMAC (ITALY) MATTRESS ROLL AND PACK MACHINE MODEL TK381 YEAR 2015
400 VOLT X 50HZ X 30 KW
8 BAR AIR PRESSURE

Learn More

M-6063 AIRLAY / THERMOBONDING PRODUCTION LINE, WIDTH 2500mm TO 2700mm, YEAR 1975 TO 2012

OFFER 001
AIRLAY / THERMOBONDING PRODUCTION LINE
WORKING WIDTH: 2500mm

OFFER 002
CROSA PERINO BLENDING BOXES
YEAR: 1990 (OVERHAULED 2011)
CAPACITY: 750 KG EACH

OFFER 003
HDB CARDING WILLOW
YEAR: 1975

OFFER 004
MESUTRONIC METAL DETECTOR
YEAR: 2007

OFFER 005
MESUTRONIC METAL SEPARATOR
YEAR: 2007

OFFER 006
FALLGARTER HOPPER FEEDER
YEAR: 1975

OFFER 007
ROLANDO HOPPER FEEDER
YEAR: 1985 (OVERHAULED 2003)

OFFER 008
HERGETH HOLLINGSWORTH FINE OPENER
YEAR: 1981

OFFER 009
STUMMER CONTINUOUS CLEANER
YEAR: 2007

OFFER 010
HERGETH HOLLINGSWORTH AIRLAY FEEDING
YEAR: 1981 (OVERHAULED 2012)
WORKING WIDTH: 2500mm

OFFER 011
OLBRICH AIRLAY CARD
YEAR: 2010
WORKING WIDTH: 2500mm

OFFER 012
STRAHM OVEN
YEAR: 2008
WORKING WIDTH: 2700mm

OFFER 013
OLBRICH LONGITUDINAL CUTTING
YEAR: 2004
WORKING WIDTH: 2600mm

OFFER 014
KZE CROSSCUTTING
YEAR: 2012
WORKING WIDTH: 2600mm

QUANTITY: 1 LINE

Learn More

REFERENCE NUMBER: K-3843 KAPOK FILLING MACHINE STUFFING MACHINE AND BLOWER KAPOK FEEDING HOPPER AIR COMPRESSOR QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-5283 (13131CKAKT12U) L ELMARCO NANOSPIDER PRODUCTION LINE NANOSPIDER PRODUCTION LINE NS 4S1000U QUANTITY AVILABLE: 1 Learn More

REFERENCE NUMBER: G-6565 CIRCULAR KNITTING MACHINES MAKER MODEL DIAMETER GAUGE FEEDS TYPE OILER VENTILATION 1 MAYER & CIE INOVIT II 30" 18 48 DOUBLE JERSEY BOY ELECTRIC 2 MAYER & CIE INOVIT II 30" 18 48 DOUBLE JERSEY BOY ELECTRIC 3 MAYER & CIE INOVIT II 30" 18 48 DOUBLE JERSEY BOY ELECTRIC 4 MAYER & CIE INOVIT II 30" 18 48 DOUBLE JERSEY BOY ELECTRIC 5 MAYER & CIE FHG 30" 14 60 DOUBLE JERSEY BOY ELECTRIC 6 MAYER & CIE FHG 30" 18 60 DOUBLE JERSEY BOY ELECTRIC 7 MAYER & CIE FHG 30" 18 60 DOUBLE JERSEY BOY ELECTRIC 8 MAYER & CIE OV 64 II 30" 18 64 DOUBLE JERSEY BOY ELECTRIC 9 MAYER & CIE IHLG 30" 18 84 RIB/INTERLOCK BOY ELECTRIC 10 MAYER & CIE INOVIT II 30" 28 48 DOUBLE JERSEY BOY ELECTRIC 11 MAYER & CIE IHLG 30" 28 84 RIB/INTERLOCK UNIWAVE ELECTRIC 12 MAYER & CIE MN-PF 30" 20 44 SINGLE JERSEY (TOWEL) BOY ELECTRIC 13 MAYER & CIE MN-PF 30" 20 44 SINGLE JERSEY (TOWEL) BOY ELECTRIC 14 MAYER & CIE MHP 30" 20 60 SINGLE JERSEY (VANIZE) UNIWAVE FANS 15 MAYER & CIE M2/JR36 PILOTELLI CONVERSION 30" 8 36 SINGLE JERSEY (MINI JACQUARD, PATTERN WHEELS) BOY FANS 49/85 16 MAYER & CIE MN-PF 30" 20 44 SINGLE JERSEY (TOWEL) FANS 17 PILOTELLI JVCE 2 34" 20 102 LYCRA SINGLE JERSEY PULSONIC ELECTRIC MO3931037 18 PILOTELLI JVCE 2 34" 28 102 LYCRA SINGLE JERSEY PULSONIC ELECTRIC MO3931016 19 PILOTELLI JVCE 2 34" 20/28 102 LYCRA SINGLE JERSEY PULSONIC ELECTRIC MO392884 20 PILOTELLI JVCE 2 34" 20/28 102 LYCRA SINGLE JERSEY PULSONIC ELECTRIC MO392878 21 PILOTELLI JVC 30" 20/28 90 SINGLE JERSEY PULSONIC ELECTRIC 22 PILOTELLI JVCE 30" 28 90 LYCRA SINGLE JERSEY PULSONIC ELECTRIC MO189432 23 PILOTELLI JVCE 30" 28 90 SINGLE JERSEY PULSONIC ELECTRIC 24 ORIZIO JRS/ PILOTELLI CONVERSION J90 30" 28 90 4-TRACKS AIR 25 MAYER & CIE JP78 PILOTELLI CONVERSION 26" 28 90 SINGLE JERSEY ELECTRIC 26 ORIZIO JOHN 30" 20 96 SINGLE JERSEY (3-CLONES) UNIWAVE ELECTRIC 27 ORIZIO FA 30" 20 90 SINGLE JERSEY AIR 28 ORIZIO JRS/ JP90 PILOTELLI CONVERSION 30" 28/10 90/45 SINGLE JERSEY BOY AIR 29 ORIZIO JRS/ JP90 PILOTELLI CONVERSION 30" 28 90 SINGLE JERSEY BOY ELECTRIC 48/85 30 ORIZIO RDM/2 30" 24 72 SINGLE JERSEY (MINI JACQUARD, PATTERN WHEELS) UNIWAVE ELECTRIC 31 MONARCH RX-DF3 30" 20 90 SINGLE JERSEY (3-CLONES) UNIWAVE ELECTRIC E8630479 32 MONARCH FXC-3S 30" 20 90 SINGLE JERSEY UNIWAVE ELECTRIC 33 MONARCH FXC-3S 30" 28 90 SINGLE JERSEY UNIWAVE ELECTRIC 34 CAMBER H3F 30" 26 90 SINGLE JERSEY HOSIERY - ALL OUR CIRCULAR KNITTING MACHINES HAVE NEEDLES BY GROZ-BECKERT. THE PILOTELLI CONVERSIONS ARE IN THE BODY OF ORIZIO, AND MAYER & CIE. MACHINES. THERE ARE MANY MORE SPARE PARTS, CYLINDERS, NEEDLES, FEEDERS, CREELS, ETC., WHICH ARE INCLUDED. Learn More