Search results for: 'air+pr'

REFERENCE NUMBER: T-6552

MASK AIR TIGHTNESS TESTER

 

MASK AIR TIGHTNESS TESTER

HOW TO CHOOSE A HIGH-QUALITY MASK NOT ONLY DEPENDS ON THE FILTERING EFFICIENCY OF THEMASK, BUT ALSO TO CONFIRM WHETHER THE MASK IS COMPLETELY IN CONTACT WITH THE FACE, OTHERWISE AEROSOL PARTICLES SUCH AS GERMS THAT HAVE NOT BEEN FILTERED BY THE MASK WILL BE INHALED FROM THE INADEQUATE ADHESION. THEREFORE, IT IS VERY IMPORTANT TO CHECK THE WEARING STATUS OF THE MASK. THE EUROPEAN AND AMERICAN COUNTRIES HAVE LISTED THE APPLICATION TEST OF THE MASK AS A STRONG INSPECTION ITEM.

FOR EXAMPLE, THE N95 MASK IS ONE OF 9 TYPES OF PARTICULATE PROTECTIVE MASKS CERTIFIED BY NIOSH (NATIONAL INSTITUTE OF OCCUPATIONAL SAFETY AND HEALTH). "N" INDICATES OIL RESISTANCE."95" INDICATES THAT THE PARTICLE CONCENTRATION IN THE MASK IS MORE THAN 95% LOWER THAN THAT OF THE PARTICLES OUTSIDE THE MASK WHEN EXPOSED TO THE SPECIFIED NUMBER OF SPECIAL TEST PARTICLES. N95 IS NOT A SPECIFIC PRODUCT NAME, AS LONG AS IT MEETS THE N95 STANDARD AND PASSES THE NIOSH REVIEW, IT CAN BE CALLED "N95 MASK".

N95 TYPE MASKS, IN ADDITION TO THE FILTERING EFFICIENCY OF THE MASKS, THE CLOSENESS OF THE MASKS TO THE FACE IS ONE OF THE IMPORTANT FACTORS THAT DETERMINE THE EFFECTIVENESS OF THE USE OF THE MASKS. THE SUITABILITY OF DIFFERENT TYPES OF MASKS FOR THE HUMAN FACE VARIES GREATLY.

THEREFORE, BEFORE USING A MASK, THE SUITABILITY OF THE MASK SHOULD BE CHECKED FIRST. DURING THETIGHTNESS TEST OF THE WEARER'S FACE, ENSURE THAT AIR CAN PASS IN AND OUT THROUGH THE MASK WHEN IT IS CLOSE TO THE EDGE OF THE FACE. THE MASK TIGHTNESS TESTER CAN QUICKLY COMPLETE THE TIGHTNESS TEST OF RESPIRATORS SUCH AS MASKS TO ENSURE THAT IT PROVIDES GOOD PROTECTION PERFORMANCE. IT CONFORMS TO THE CHINESE RESPIRATOR STANDARD GB2626-2019 STANDARD, OSHA / CSA STANDARD AND CHINA GENERAL ADMINISTRATION OF QUALITY SUPERVISION, INSPECTION AND QUARANTINE "GB 19083-2010 TECHNICAL REQUIREMENTS FOR MEDICAL PROTECTIVE MASKS" JOINTLY ISSUED BY THE CHINA NATIONAL STANDARDIZATION ADMINISTRATION COMMITTEE.

ADHESION (SUITABILITY TEST): THE MASK DESIGN SHOULD PROVIDE GOOD ADHESION. THE OVERALL FIT FACTOR OF THE MASK SHOULD NOT BE LESS THAN 100. THIS TEST THE REQUIREMENTS WERE FORMALLY IMPLEMENTED ON AUGUST 1, 2011.

Learn More

REFERENCE NUMBER: L-5934

MONFORTS 6-F TWIN AIR STENTER YEAR 2003 – WORKING WIDTH 2400mm

 

STENTER

RAMA MONFORTS

MAKE: MONFORTS

MODEL: 6-F TWIN

YEAR: 2003

440 VAC 60HZ

NATURAL GAS

AIR COMPRESSOR 7 BAR

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: T-6588

MEDICAL PROTECTIVE CLOTHING

 

ITEM NAME: MEDICAL PROTECTIVE SUITS

MATERIAL; SMSNON WOVEN +MELTBLOWN NON-WOVEN FABRIC +THREE LAYER FIBER WEB

PRODUCT QUALIFICATION:CE CERTIFICATION AND FDA PHARMACEUTICAL INDUSTRY LICENSE

PRODUCT DESCRIPTION: RADIATION STERILIZED PROTECTIVE CLOTHING THAT CAN ENTER ICU PROTECTION FOR UP TO 24 HOURS

PRODUCT PERFORMANCE: SOFT, LIGHT, GOOD AIR PERMEABILITY, WATERPROOF AIR PERMEABILITY 7770 / M2 / DAY

THE SURFACE MOISTURE RESISTANCE REACHES LEVEL 4 (GB / 74745 /1997)

THE ANTI SYNTHETIC BLOOD PENETRATION REACHED GRADE 4

SIZE: S,M,L, XL, 2XL

PACKAGE SIZE: APPROX: 650 X 340 X 285mm

PACKAGE WEIGHT: APPROX. 260G / 9.2OZ

 

LEAD TIME STOCK: 3-4 DAYS BY FEDEX; MASS GOODS: 3-7 DAYS

ITEM 001

QUANTITY: 1,000

ITEM 002

QUANTITY: 5,000

ITEM 003

QUANTITY: 15,000

 

LEAD TIME STOCK: 3-4DAYS BY FEDEX; MASS GOODS: 8-15 DAYS

ITEM 004

QUANTITY: 50,000

ITEM 005

QUANTITY: 100,000

Learn More

REFERENCE NUMBER: T-6843 SPINNBAU NONWOVEN LINE, YEAR 1994 BRAND: SPINNBAU SHORT DESCRIPTION: NONWOVEN LINE YEAR: 1994 NONWOVEN LINE CONSISTING OF 1. CARD FEEDING: CARD FEEDING R&S, NEW, IN 2500mm WORKING WIDTH, CONSISTING OF: ONE R&S MATERIAL BIN IN 2500mm WORKING WIDTH, 600mm DEPTH AND A COMPLETE HEIGHT OF 2500mm, WITH TOP AND BOTTOM WINDOW AT BOTH SIDES, FILLING LEVEL CONTROLLED BY IN HEIGHT ADJUSTABLE INFRARED DEVICES. ONE DOOR AT THE BACKSIDE FOR CLEANING, LOCKED BY SECURITY SWITCHES. THE VITIATED AIR ESCAPES THROUGH THE PERFORATED SHEETMETAL AT THE TOP. THESE AREAS ARE COMPLETELY COVERED, THE OUTGOING AIR CAN BE FILTERED BY AN EXCISTING FILTERSTATION OR OPTIONALLY BY FILTERBAGS, 2 DELIVERY ROLLERS. ONE R & S CHUTE FEEDER IN 2500mm WORKING WIDTH CONSISTING OF: ONE OPENING ROLLER DIAMETER 450mm, ONE VIBRATION CHUTE, FIBRELEVEL CONTROLLED BY ULTRASONIC, CHUTE ADJUSTABLE OVER TOOTH RAILS IN DEPTH FROM 80 TO 240mm, TWO DRAWING OFF ROLLERS, ONE FEEDING TABLE WITH TRANSILON BELT, PREPARED FOR SERVOLAP. DRIVES: DELIVERY ROLLERS: AC -GEARBOXMOTOR 0.55 KW, FC OPENING ROLLER: AC-MOTOR 2.2 KW VIBRATION: AC-GEARBOXMOTOR, 0.55 KW, FC FEEDING TABLE: AC-GEARBOXMOTOR, 0.55 KW, FC 2. CARDING; ONE SPINNBAU DOUBLE DOFFER CARD, IN 2500mm WORKING WIDTH, YEAR 1994: CARD, FOLLOWING EQUIPPED: 1 CYLINDER FEEDING DEVICE WITH FEED PLATE: 1 FEED ROLLER DIAMETER 159mm 1 LICKER-IN DIAMETER 292mm PRE-OPENING: 1 BREAST DIAMETER 412mm 1/1 WORKER/STRIPPER DIAMETER 213/118mm 1 INTERMETE ROLLER DIAMETER 412mm CARD: 1 MAIN CYLINDER DIAMETER 1500mm 5/5 WORKERS/STRIPPERS DIAMETER 213/118mm 1 DOFFER, TOP DIAMETER 550mm 1 DOFFER, BOTTOM DIAMETER 550mm 2 CONDENSING ROLLERS TOP DIAMETER 292mm TOP DRAWING OFF DEVICE, NEW: 1 DRAWING OFF ROLLER/WIRED DIAMETER 159mm 1 DRAWING OFF ROLLER/STEEL RUBBER: DIAMETER 159mm 1 CLEANING ROLLER WITH INTEGRATED ELECTRONIC, WHEN DIAMETER OF CLEANING IS GETTING BIGGER, CARD WILL STOP. BOTTOM DRAWING OFF DEVICE, NEW: 1 DRAWING OFF ROLLER/WIRED DIAMETER 159mm 1 DRAWING OFF ROLLER/STEEL RUBBER: DIAMETER 159mm 1 CLEANING ROLLER WITH INTEGRATED ELECTRONIC, WHEN DIAMETER OF CLEANING IS GETTING BIGGER, CARD WILL STOP. DRAWING OFF TABLES: TOP TRANSILON BELT BOTTOM: TRANSILON BELT COVERS: THE CARD HAS COVERS TO CLAP UP AND DOWN (SECURED WHEN CLAPPED UP), THE SIDES ARE FULLY COVERED AND ELECTRONICALLY LOCKED. RIGID WIRE: ONE COMPLETE SET OF RIGID WIRE, MOUNTED, FOR FIBRES 1.5 DTEX - 17 DTEX, CAPACITY UP TO 800 KG/H ELECTRIC: VOLTAGE: ~400 V AC, 3 PHASES CONTROL VOLTAGE: ~220 V AC, =24V DC FREQUENCY: 50 Hz COLOUR: MACHINE: RAL 5015/ 9001 (IF YOU LIKE WE CAN CHANGE) CONTROL CABINET: RAL 7032, GREY SWITCH BOARD: RAL 7032, GREY ELECTRICAL DRIVES: FEED ROLLER: 1 AC GEARBOXMOTOR, FREQUENCY CONTROLLED LICKER-IN: MECHANICAL FROM BREAST BREAST: 1 AC GEARBOXMOTOR, FREQUENCY CONTROLLED WORKERS BREAST: MECHANICALLY FROM BREAST INTERMEDIATE ROLLER: MECHANICALLY FROM MAINSWIFT MAIN SWIFT: 1 AC-MOTOR FREQUENCY CONTROLLED WORKERS: 1 AC GEARBOXMOTOR, FREQUENCY CONTROLLED DOFFERS: 2 AC GEARBOXMOTORS. FREQUENCY CONTROLLED CONDENSING ROLLERS: 1 AC GEARBOXMOTORS. FREQUENCY CONTROLLED DRAWING-OFF DEVICES: 2 AC GEARBOXMOTORS. FREQUENCY CONTROLLED DRAWING-OFF TABLES: 2 AC GEARBOXMOTORS, FREQUENCY CONTROLLED SWITCHBOARDS AND CONTROLS: SWITCHBOARDS RITTAL SERIES, COMPLETE WIRED. SWITCHBOARDS WITHOUT COOLING DEVICES. CONTROL CABINET OPERATION WITH COLOURED SCREEN, FITTED IN CONTROL CABINET OPERATED BY SIEMENS SPS S7-300 1 SET OF CABLE MATERIAL: FOR 20 MTR LENGTH BETWEEN MACHINERY AND SWITCHBOARD WITHOUT INSTALLATION MATERIAL ERECTION AND STARTING UP: IS NOT INCLUDED, SHOULD BE MADE BY US FOUNDATION: ONE FOUNDATION IN 750mm HEIGHT, WITH SIDEWALKS AROUND, TWO STEPS ON EACH SIDE. SUCTION: CONNECTION FOR THE DOFFER AND TOP OF CARD 3. CROSSLAPPING, NEW: ONE REISKY & SCHLESE CROSSLAPPER, TYPE RS 100 IN 2500mm WORKING WIDTH (BELT WIDTH 2800mm) AND 2500mm LAPPING WIDTH (BELT WIDTH 2700mm) MAX INFEEDING SPEED: 100 MTR/MIN, DELIVERY SPEED OF DRAWING OFF TABLE: FROM 0 TO 20 MTR/MIN, CONSISTING OF: ONE FEEDING TABLE IN 1000mm LENGTH MOUNTED IN IT'S OWN FRAME, ADJUSTABLE IN THE HEIGHT ACCORDING TO THE DOFFER, FURTHER THE COMPLETE FEEDING TABLE CAN BE MOVED UP IF THE DOFFER HAS TO BE DRAWN BACK. THE CROSSLAPPER ITSELF GUIDES THE WEB FROM THE INFEED DOWN TO THE OUTLET BETWEEN THE CONVEYORS, WHICH HAVE ANTISTATIC PROPERTIES. THE TENSION AND THE DISTANCES BETWEEN THEM CAN BE ADJUSTED ACCORDING TO THE DIFFERENT FIBRES. THE CONVEYORS ARE EQUIPPED WITH AUTOMATIC EDGE GUIDES, SO THAT THEY ARE RUNNING IN THE CENTRE. THE LAID WEB IS COVERED BY THEM. THE SERVO- DRIVES ARE RESPONSIBLE FOR THE PERFECT SYNCHRONISATION AND THE EXACT REVERSAL OF THE CARRIERS. THE SWITCHBOARD IS EQUIPPED WITH A COULOURED TOUCHSCREEEN, WHERE ALL NECESSARY PARAMETERS CAN BE PROGRAMMED, ALSO DIFFERENT CURVES FOR STORING THE WEB DURING REVERSALS. DRIVES: FEED TABLE: AC-SERVO-MOTOR BELT 1: AC-SERVO-MOTOR BELT 2: AC-SERVO-MOTOR TOP CARRIER: AC-SERVO-MOTOR BOTTOM CARRIER: AC-SERVO-MOTOR DRAWING OFF TABLE: AC-SERVO-MOTOR HEIGHT DRAWING OFF TABLE LEFT: AC-LINEARMOTOR HEIGHT DRAWING OFF TABLE RIGHT: AC-LINEARMOTOR OPERATION: BY COLOURED TOUCHSCREEN, SIEMENS IN CONTROL CABINET OF CARD. PARAMETERS: MANUEL / INLINE INFEED SPEED DRAFT (INFEED SPEED/LAYING SPEED) NUMBER OF LAPS LAPPING WIDTH FROM MIDDLE TO THE LEFT AND TO THE RIGHT DRAWING OFF SPEED AUTOMATICALLY SHOWN DEPENDING ON LAYERS DARWING OFF TABLE HEIGHT LEFT / RIGHT LAYING SPEED RECEIPES FAULT SHOWING SWITCHBOARD AND ELECTRONIC DEVICES: SWITCH BOAD RITTAL, COMPLETE WIRED. SWITCHBOARD WITHOUT COOLING DEVICE. CONTROL PANNEL RITTAL. CONTROLLED BY S7 SIEMENS 10000mm OF CABLES BETWEEN SWITHBOARD AND MACHINE/CONTROLPANEL QUANTITY: 1 Learn More

TILE FACTORY DESIGNED BY SACMI / ITALY
YEAR ESTABLISHED 2014 TO 2016
THIS PLANT IS AN ENVIRONMENTALLY FRIENDLY ENTERPRISE, WHEN IT RECYCLES 100% OF ITS EFFLUENTS AND PERFORMS HEAT RECOVERY, THEREBY SAVING ENERGY

See all pictures:
https://www.flickr.com/photos/183869481@N08/albums/72157710649767958

THE PLANT:
COVERS AN AREA OF 22 THOUSAND SQUARE METERS
THE PRODUCTION CAPACITY IS 7 MILLION SQUARE METERS / YEAR
CERAMIC FLOOR TILES
CERAMIC WALL TILES
BMR POLISHING LINE
BMR SQUARING & CHANFERING LINE
THE MAIN RAW MATERIALS ARE CLAY (DB-4) - 31 %, ALBITE (STD5) - 60 %
NEPHAIIN (PN9595) - 2.5 %, KAOLIN (RHB1) - 6.5 %
ON TOP OF IT THEY ARE USING GLAZE MATERIALS AND PAINTS
•FROM THE MOMENT THE MATERIAL IS PREPARED IT IS BEING DRIED PRESSED ON ONE OF FOUR (4) PRODUCTION LINES.
•TWO (2) LINES ARE WITH SACMI PRESSES OF PH 7,500 TON EACH AND HORIZONTAL DRYERS SACMI
•TWO LINES ARE WITH SACMI PRESSES OF PH 3,590 TON EACH AND VERTICAL DRYERS SACMI
•ALL FOUR (4) LINES HAVE THEIR OWN DIGITAL PRINTING MACHINE INCORPORATED
•ALL PRODUCTS ARE BEING GLAZED AND FIRED ON 1200 DEGREES IN ONE OF THE TWO (2) KILNS, SACMI
FOUR (4) SORTING, PACKING AND PALLETIZING LINES
GLAZE PREPARATION LINE
COMPLETE INSTALLATION FOR SMALL PRODUCTION CAPACITIES
COMPLETE FOILING LINE
COMPLETE ELECTRIC INSTALLATION
POWER GENERATOR UNIT
COMPRESSED AIR INSTALLATION

MACHINES ARE MADE BY:
SACMI: ITALY
NUOVA ERA / ROBOBOX: ITALY
BMR: ITALY
IN.TE.SA: ITALY
CUCCOLINI: ITALY
SYSTEM CERAMICS: ITALY
TGMAC SR.L: ITALY
DURST: GERMANY
ROTOCOLOR MAG: ITALY
NUOVA FIMA: ITALY
OMS: ITALY
MARPAK OMS: ITALY
MESSERSI PACK: ITALY

TILE SIZES
THE FACTORY MANUFACTURES TILES OF VARIOUS SIZES FROM 300 X 300 TO 1200 X 1200mm IN VARIOUS TEXTURES AND DESIGNS USING DIGITAL PRINTING MACHINES
PRODUCTION CAPACITY IS 7 MILLION SQUARE METERS / YEAR
THE FACTORY IS FULLY AUTOMATED AND USING ADVANCED CONTROL SYSTEMS!

HUGE AMOUNT OF ORIGINAL SPARE PARTS AVAILABLE WITH THIS PLANT
THIS PLANT IS AVAILABLE WITH THE COMPLETE ELECTRIC, AIR, GAS, RECYCLING INSTALLATION

THIS PLANT CAN BE SOLD: WITH 4 LINES OR 2 AND 2 LINES

 

Learn More

REDUCES VOLUME FOR STORAGE AND TRANSPORTATION
USES COMPRESSED AIR AND PLASTIC COMPOSITE FILM BAGS FOR PACKAGING ITEMS AFTER COMPRESSION
EQUIPPED WITH AUTOMATIC TRANSMISSION TO COMPRESS AND FILM ITEMS UNINTERRUPTED
STANDARD MODEL EQUIPPED WITH ONE WORKSTATION WITH SINGLE SEAL (OPTIONAL ONE WORKSTATION WITH DOUBLE SEALS)
PLC TOUCH SCREEN OPERATION, USER FRIENDLY INTERFACE
CONSTANT TEMPERATURE CONTROL FUNCTION TO PREVENT BAG BURNS

VOLTAGE AND POWER: 220 V SINGLE-PHASE, 0.5 KW, 50 Hz
AIR PRESSURE: 0.4 – 0.8 MPA
PACKING CAPACITY: : 8 TO 12 ITEMS PER MINUTE
PRESS BOARD SIZE: LENGTH 700mm x WIDTH 900mm
MAXIMUM COMPRESSION THICKNESS: 500mm (AIR CYLINDER TRAVEL)
SEAL LENGTH: 880mm x 10mm
OVERALL DIMENSIONS: LENGTH 3390mm x WIDTH 940mm x HEIGHT 2010mm
POWER: 1.5 KW
NET WEIGHT: 350 KG
GROSS WEIGHT: 400 KG

QUANTITY: 1

Learn More

T-2898 PP STAPLE FIBER PLANT, 6000 MTA, BRAND MOSTLY FLEISSNER , AUTEFA BALE PRESS
20 TONS PER DAY

PP STAPLE FIBER SYSTEM
6000 MTA (LINE-1+LINE-2)
EXTRUTION & SPINNING PACKAGE

Learn More

Learn More

REFERENCE NUMBER: R-1390
OSTHOFF SINGEING/CORINO ENTRY & EXIT/PAREX & DESIZING RANGE, WORKING WIDTH 2000mm, YEAR 1995 - RECONDITIONED 2015
DETAILS:
BRAND:OSTHOFF
WORKING WIDTH: 2000mm
YEAR: 1995
FULLY RECONDITIONED IN YEAR: 2015

COMPRISING OF:

ITEM 001
CORINO DE- BATCH- J BOX & BRUSH
WORKING WIDTH: 2000mm
QUANTITY: 1

ITEM 002
OSTHOFF SINGEING MACHINE
TYPE: PK 90
MAXIMUM FABRIC WIDTH: 2000mm
MAXIMUM FLAME WIDTH: 2200mm
QUANTITY: 1

ITEM 003
GAS BURNERS WITH AUTO IGNITION ELECTRODES
WORKING WIDTH: 2000mm
QUANTITY: 2

ITEM 004
PAREX DESIZING WITH 2 BOWL PADDER
QUANTITY: 1

ITEM 005
ONE PAREX OPEN WIDTH DESIZING - WASHING TANK
WORKING WIDTH: 2000mm
QUANTITY: 1

Learn More

L-1177 TRUTZSCHLER/RIETER COMPLETE SPINNING MILL

BLOW ROOM TRÜTZSCHLER

1 MONOTAMBOUR B4/1, YEAR 1989
1 MULTIMIXER MCM 6 /1200 YEAR 1997 + 1 CVT-4 / 1200 YEAR 1997
1 JOSSI THE VISION SHIELD FIBER DETECTOR EA-33-S YEAR 2002
1 DUSTEX DX 385 YEAR 1997
1 JOSSI THE SHIELD HIGH PERFORMANCE FIRE DETECTOR
TYPE D-11-250, YEAR 2005
3 TRÜTZSCHLER FAN
1 UNIMIX RIETER + ERM CLEANER RIETER
QUANTITY: 1

BLOW ROOM RIETER

2 ERM B 5/5 YEAR 1989
1 ERM B 5/5 YEAR 1987
1 ERM B 5/5 YEAR 1988
2 JOSSI FIRE DETECTOR D-11-250 YEAR 2005
1 JOSSI FIBRE DETECTOR EA-33-S, YEAR 2002
3 BALE PRESS RIETER B3/4S, YEAR 1990-1991
QUANTITY: 1

CARDS TRÜTZSCHLER DK-803, YEAR 1996/ 1997 (3) COILER KH 950-1200,
AUTOMATIC REVOLVER, FEEDING FBK-533
QUANTITY: 3

CARDS TRÜTZSCHLER DK-903, YEAR 2002/2003 (1) COILER KH 600-1200, (2) COILER KH 450-1200
AUTOMATIC REVOLVER, FEEDING DKF
QUANTITY: 3

DRAWING FRAME TRÜTZSCHLER HSR-1000X2 , YEAR 2003, 1 DELIVERY 18” (450X1000), CREEL 8 CANS,
SLIVER MONITOR, AUTOLEVELLER
QUANTITY: 2

2 ROVING FRAME SIMPLEX ZINZER 670, YEAR 2003, DRAFT PK 1500, 120 SPINDLES,
CAPACITY BOBBIN 16”X6”, DRIVER CREEL, COLLECTIVE ASPIRATION,
INDIVIDUAL BLOWER ELECTRO-JET
2 AUTOMATIC TRANSPORT INSTALLATION FOR BOBBINS ELECTRO-JET
FOR 8 RING SPINNING FRAME OF 1.200 SPINDLES, YEAR 2003
QUANTITY: 1

5 RING SPINNING FRAME ZINZER RM 351, YEAR 2002 (4), YEAR 2003 (1), 1200 SPINDLES,
GAUGE 70 MM
DRAFT PK 2500, RING 42 MM, TUBE 220 MM, COWEMAT, COLLECTIVE ASPIRATION, INDIVIDUAL BLOWER
ELECTRO-JET WITH AUTOMATIC UNLOADING, TOTAL LENGTH 47 M

4 WINDER SCHLAFHORST 338 RM, 2 X YEAR 2002, COLOUR GREEN, 2 X YEAR 2003, COLOUR WHITE, 60 POSITIONS
MAGAZINE FEEDING 6 TUBES, 2 ROBOTS, WAXING, AUTOMATIC CONE CHANGE, TK-840,
CLEARER LOEPFE, DELIVERY 4.20 X 6”, INDIVIDUAL BLOWER
QUANTITY: 1

1 AUTOCORO SCHLAFHORST SE-11 ACO-288, YEAR 2001, 216 ROTORS, INFORMATOR,
DELIVERY CYLINDRICAL SLUBIER PINTER, ROTOR Ø 28-36-40 MM , ROLLERS B-174, CLEARERS COROLAB,
WAXING, 2 ROBOTS CONE CHANGE ROBOTS PIECERS
QUANTITY: 1

1 AUTOCORO SCHLAFHORST SE-9, 216 ROTORS, 2 ROBOTS, WAXING, COROLAB
INFORMATOR, YEAR 1998
QUANTITY: 1

1 INSTALLATION LTG, YEAR 2003, 5 PARTS, WASTE COLLECTING, AIR SYSTEM
1 INSTALLATION LTG, YEAR 2003, 3 PARTS, WASTE COLLECTING, AIR SYSTEM
1 INSTALLATION LTG, YEAR 2003, 5 PARTS, WASTE COLLECTING, CARDING FILTRATION

- POWER 380V/50HZ
- CONDITION COMPLETED
QUANTITY: 1

RIETER SPINNING COMBING PLANT

BLOW ROOM RIETER
UNIFLOC RIETER, A1/2, YEAR 2000
UNIMIX RIETER , B7/3, YEAR 2000
UNILEX B60, YEAR 2000
JOSSI , D-21-370-01, YEAR 2000
QUANTITY: 1

CARDS RIETER
10 X CARD RIETER C51, YEAR 2000, WITH IGS
WITH LUWA WASTE SYSTEM
QUANTITY: 10

1 X CARD RIETER C60 WITH MODUL IGS
YEAR :
QUANTITY: 1

DRAWING FRAMES RIETER
2 X DRAWING FRAME RIETER, SB-D10, YEAR 2000
QUANTITY: 2

1 X DRAW FRAME RIETER, RSB-D30C, YEAR 2000
QUANTITY: 1

2 X DRAWING FRAME RIETER, D-30

QUANTITY: 2
1 X DRAWING FRAME RIETER, D-35

QUANTITY: 1

COMBERS RIETER

1 X UNILAP RIETER E33, YEAR 2000
WITH TRANSPORT SYSTEM SCHONENBERGER , ARS-N2, 2000

5 X COMBING MACHINE RIETER , E72, YEAR 2000
1 X COMBING MACHINE RIETER, E75, YEAR 2006
1 X SERVOLAP RIETER , E25, YEAR 2000
WITH WASTE COLLECT SYSTEM AND PRESS
QUANTITY: 1

FLYERS RIETER
3 X ROVING FRAME RIETER, F33/120POS, YEAR 2000
AUTOMATIC BOBINES TRANSPORT , SCHONENBERGER , YEAR 2000
QUANTITY: 1

RING SPINNING MACHINES RIETER
6 X SPINNING FRAME RIETER G33
6 RIETER RINGFRAMES, TYPE G33, BUILT 1999, EACH WITH 1200 SPINDLES, RING DIAMETER 38 MM, TYPE SFB-TITAN, GAUGE 70 MM, LIFT 187 MM, SPINDLE TYPE HPS 25, AUTOMATIC DRAFTING SYSTEM, WITH AUTODOFFER AND MAGITEX OVERHEAD CLEANER, LINKED WITH MURATA CONER, TYPE 7V-II, BUILT 1999, EACH WITH 32 WINDING HEADS, AUTOMATIC FEEDING, AUTOMATIC PACKAGE CONVEYOR, YARN CLEARERS USTER QUANTUM WITH FIBER DETECTOR, MK-C-15F23, WITH WAXING, INFORMATOR MMC/3, CONICITY 4 DEG. 20 , VOLTAGE : 380V, 50HZ
QUANTITY: 6

1 X MURATA MINICONER

LUWA AIRCONDITION, YEAR 2005
LUWA FILTER FOR CADING, YEAR 2005
LUWA FILTER FOR COMBING, YEAR 2005
LUWA FILTER FOR SPINNING AND WINDING, YEAR 2005
QUANTITY: 1

Learn More