Search results for: 'Automatic 4 s'

REFERENCE NUMBER: T-6547

RESPIRATOR RESISTANCE TESTER FOR FACE MASKS

INTRODUCTION

THE RESPIRATOR RESISTANCE TESTER IS USED TO MEASURE THE INSPIRATORY RESISTANCE AND EXPIRATORY RESISTANCE OF RESPIRATORS AND RESPIRATOR PROTECTORS UNDER SPECIFIED CONDITIONS. IT IS APPLICABLE TO THE NATIONAL LABOR PROTECTION EQUIPMENT INSPECTION INSTITUTIONS, MASK MANUFACTURERS FOR THE GENERAL MASKS, DUST MASKS, MEDICAL MASKS, ANTI-SMOG MASKS PRODUCTS OF THE RELEVANT TESTING AND INSPECTION.

STANDARD

GB 19083-2010 TECHNICAL REQUIREMENTS FOR MEDICAL PROTECTIVE MASKS

GB 2626-2006 RESPIRATOR SELF-SUCTION FILTER RESPIRATOR AGAINST PARTICULATE MATTER

GB/T 32610-2016 TECHNICAL SPECIFICATIONS FOR DAILY PROTECTIVE MASKS

FEATURES:

1. HIGH-DEFINITION LCD DISPLAY.

2. DIGITAL DIFFERENTIAL PRESSURE METER WITH HIGH PRECISION IMPORTED BRAND.

3. HIGH PRECISION IMPORTED BRAND OF DIGITAL FLOWMETER, WITH HIGH FLOW CONTROL ACCURACY FEATURES.

4. THE RESPIRATOR RESISTANCE TESTER CAN SET UP TWO MODES: EXHALATION DETECTION AND INHALATION DETECTION.

5. AUTOMATIC PIPELINE SWITCHING DEVICE OF RESPIRATOR SOLVES THE PROBLEM OF PIPE EXTUBATION AND WRONG CONNECTION WHEN TESTING.

PARAMETER:

1. FLOWMETER RANGE: 0 ~ 100L/MIN, ACCURACY IS 3%

2. DIGITAL PRESSURE DIFFERENCE METER RANGE: 0 ~ 2000PA, ACCURACY: 1PA

3. PUMPING CAPACITY OF AIR PUMP: >100L/MIN

4. OVERALL SIZE: 460 X 1080 X 670mm

5. POWER SOURCE: AC220V 50HZ 650W

6. WEIGHT: 55KG

QUANTITY: 1

USES ROCKCHIP RK3288 / RK 3399 / QUALCOMM MSM8953 HIGH-PERFORMANCE HARDWARE PLATFORM, EQUIPPED WITH INDUSTRIAL GRADE BINOCULAR CAMERA, LIVE FACIAL RECOGNITION SOFTWARE AND INFRARED THERMAL IMAGING MODULE TO SUPPORT FACE-WITH-MASK INDEITIFICATION.

SUPPORTS EXPANSION OF VARIOUS PERIPHERALS SUCH AS ID CARD READERS, FINGERPRINT READERS, ETC WHICH CAN BE APPLIED TO GATE PASSAGES AND ATTENDANCE SYSTEM TO ACHIEVE SAFE AND EFFICIENT ACCESS CONTROL FOR PERSONNEL

CAN BE USED WITH ACCESS GATES & ATTENDANCE FOR COMMUNITIES, OFFICES, SCHOOLS, HOTELS, PUBLIC VENUES, TRANSPORTATION HUBS AND PUBLIC SERVICE PLACES

FEATURES:
8 INCH IPS FULL-VIEW LCD DISPLAY
INDUSTRIAL APPEARANCE, WATERPROOF AND SUNPROOF DESIGN
STABLE AND RELIABLE
SUPPORTS A DATABASE OF 30,000 FACES
THE 1:1 COMPARISON RECOGNITION RATE IS MORE THAN 99.7%
THE 1:N COMPARISON RECOGNITION RATE IS MORE THAN 96.7% @ 0.1% MISRECOGNITION RATE
LIVE DETECTION ACCURACY RATE: 98.3% @ 1% MISRECOGNITION RATE
FACE RECOGNITION PASS SPEED IS LESS THAN 1 SECOND
SUPPORTS ACCURATE FACE RECOGNITION AND COMPARISON WHILE WEARING A MASK
USES INDUSTRIAL GRADE BINOCULAR WIDE DYNAMIC CAMERA, NIGHT INFRARED AND LED DUAL PHOTO FLOOD LAMP
ROCKCHIP RK3288 QUAD-CORE PROCESSOR, ROCKCHIP RK3399 SIX-CORE PROCESSOR, AND QUALCOMM MSM8953 OCTA-CORE PROCESSOR
SUPPORTS HUMAN BODY TEMPERATURE DETECTION AND DISPLAY (BEST TEMPERATURE DETECTION DISTANCE IS 0.5 METERS, MAXIMUM IS 1 METER), MEASUREMENT ERROR +/- 0.5 °C
TEMPERATURE CAN BE READ IN ONLY A FEW SECONDS AND THE DEVICE AUTOMATICALLY SOUNDS AN ALARM FOR ABNORMALITIES
ATTENDANCE TEMPERATURE MEASUREMENT DATA EXPORTED IN REAL TIME
VARIOUS PERIPHERALS AVAILABLE FOR ID CARD READING, FINGERPRINT READING, IC CARD READING, 2-DIMENSIONAL CODE READING, ETC.
WITH COMPLETE DOCUMENTATION AND SUPPORT FOR SECONDARY DEVELOPMENT
SUPPORTS SYSTEM LEVEL, APP OFFLINE LEVEL, APP AND BACKGROUND NETWORK LEVEL MULTIPLE API DOCKING

CAMERA
RESOLUTION 2 MILLION PIXELS
TYPE BINOCULAR WIDE DYNAMIC CAMERA
APERTURE F2.4
FOCUSING DISTANCE 50-150CM
WHITE BALANCE AUTO
PHOTO FLOOD LIGHT LED AND IR DUAL PHOTO FLOOD LIGHT

SCREEN
SIZE 8.0 INCH IPS LCD SCREEN
RESOLUTION 800×1280
TOUCH NOT SUPPORTED (OPTIONAL SUPPORT)

PROCESSOR
CPU RK3288 QUAD-CORE (OPTIONAL RK3399 SIX-CORE, MSM8953
EIGHT-CORE)
STORAGE EMMC 8G

INTERFACE
NETWORK MODULE ETHERNET AND WIRELESS (WIFI)
AUDIO 2.5W / 4R SPEAKERS
USB 1 USB OTG, 1 USB HOST STANDARD A PORT
SERIAL COMMUNICATION 1 RS232 SERIAL PORT
RELAY OUTPUT 1 DOOR OPEN SIGNAL OUTPUT
WIEGAND ONE WIEGAND 26/34 OUTPUT, ONE WIEGAND 26/34 INPUT
UPGRADE BUTTON SUPPORT UBOOT UPGRADE BUTTON
WIRED NETWORK 1 RJ45 ETHERNET SOCKET

FUNCTION
CREDIT CARD READER NONE (OPTIONAL IC CARD READER, ID CARD, ID CARD)
FACE DETECTION SUPPORTS DETECTION AND TRACKING OF MULTIPLE PEOPLE AT THE SAME
TIME
FACE LIBRARY UP TO 30,000
1: N FACE RECOGNITION SUPPORT
1: 1 FACE COMPARISON SUPPORT
STRANGER DETECTION SUPPORT
IDENTIFY DISTANCE
CONFIGURATION
SUPPORT
UI INTERFACE CONFIGURATION SUPPORT
UPGRADE REMOTELY SUPPORT
INTERFACE INTERFACES INCLUDE DEVICE MANAGEMENT, PERSONNEL / PHOTO
MANAGEMENT, RECORD QUERY, ETC.
DEPLOYMENT METHOD SUPPORT PUBLIC CLOUD DEPLOYMENT, PRIVATIZED DEPLOYMENT, LAN
USE, STAND-ALONE USE

INFRARED THERMAL IMAGING MODULE
TEMPERATURE DETECTION SUPPORT
TEMPERATURE DETECTION 1 METER (OPTIMAL DISTANCE 0.5 METER)
DISTANCE
TEMPERATURE
MEASUREMENT ACCURACY
≤ ±0.5℃
TEMPERATURE
MEASUREMENT RANGE
10℃~42℃
THERMAL FIELD OF VIEW 32 X 32℃
VISITORS' TEMPERATURE IS
NORMAL AND RELEASED
DIRECTLY
SUPPORT
ABNORMAL TEMPERATURE
ALARM
SUPPORT (TEMPERATURE ALARM VALUE CAN BE SET)

GENERAL PARAMETERS
POWER DC12V（±10%）
OPERATING TEMPERATURE 0℃~60℃
STORAGE TEMPERATURE -20℃~60℃
POWER CONSUMPTION 13.5W（MAX）
INSTALLATION METHOD GATE BRACKET INSTALLATION
SIZE : STANDARD：274.24*128*21.48（MM）; IC CARD / ID CARD：296.18*132.88*25（MM）

PACKING LIST
MACHINE * 1, POWER ADAPTER * 1, MANUAL * 1, CERTIFICATE OF CONFORMITY * 1

PC MAIN SPECS:
CPU: HISILICON HI3516D V300 DUAL CORE, CORTEX-A7, 1.0 TOPS
RAM: 4GB
STORAGE: 16GB (CAN SAVE 50,000 FACE DATABASE)
LINUX OS
WORKING TEMPERATURE: -20°C TO 60°C
SUPPORT LIVE DETECTION
SUPPORT FACE RECOGNITION, RECOGNITION DISTANCE: ≤500mm, TIME: ≤ 0.2S
SUPPORT AUTOMATIC TEMPERATURE DETECTION, RECOGNITION DISTANCE: ≤ 500mm, TIME: ≤0.3S
SUPPORT THE SECONDARY DEVELOPMENT OF DEVICE-SIDE APPLICATION
SOFTWARE

LCD PANEL MAIN SPECS:
RESOLUTION: 800 X 1280 (10:16)
BRIGHTNESS: 500CD/M2 (TYP)
CONTRAST: 800:1
INTERFACES: 1 X LAN/ 1 X WIGEN OUTPUT/1 X RELAY OUTPUT/ 1 X DC INPUT
SUPPORT DISPLAY OUTPUT TO LAPTOP PC OR DESKTOP PC VIA LAN PORT
SENSOR:
1 X FAR INFRARED TEMPERATURE SENSOR
1 X 2MP FRONT CAMERA

A. SEMI-AUTOMATIC N95 FACE MASK MACHINE
30 TO 45PCS/MIN
MAXIMUM ROLL DIAMETER: 600mm
NUMBER OF ROLLS FEEDING THE MACHINE: 4 ROLLS OR 4 LAYERS
WIDTH OF THE ROLL: 230mm
TOTAL KW OF THIS MACHINE: 3KW
FREQUENCY (KHZ) OF THE ROTARY ULTRASONIC DIE: 15KHZ 2600W
DIAMETER OF THE ROTARY DIE: 74mm
FLOOR SPACE DIMENSIONS OF THIS MACHINE: 3000mm X 1500mm
MACHINE WEIGHT: 400KGS
PACKING DIMENSIONS OF THE MACHINE: 1600mm X 1000mm X 1700mm(L X W X H)
HEIGHT OF THE MACHINE: 1960mm

B. N95 EARLOOP MACHINE
15 TO 20PCS/MIN
NUMBER OF PAIRS OF EAR LOOPS DONE PER MINUTE: 15 TO 20PCS/MIN
FLOOR SPACE DIMENSIONS OF THE MACHINE: 1200mm X 1000mm
MACHINE WEIGHT: 350KGS
PACKING DIMENSIONS OF THE MACHINE: 1200mm X 1000mm X 1500mm(L X W X H)
HEIGHT OF THE MACHINE: 1300mm
SPOT WELDING IS USED TO ADHERE THE CLIP TO THE MESK. NO GLUE IS USED.

C. N95 SEALING MACHINE
15 TO 20PCS/MIN
TOTAL KW OF THE MACHINE: 20K 2600W
FREQUENCY (KHZ) OF THE ROTARY ULTRASONIC DIE: 20K
FLOOR SPACE DIMENSIONS OF THE MACHINE: 600mm X 600mm
MACHINE WEIGHT: 100KGS
PACKING DIMENSIONS OF THE MACHINE: 700mm X 700mm X 1300mm (L X W X H)
HEIGHT OF THE MACHINE: 1200mm

D. N95 NOSE CLIP MACHINE
15 TO 20PCS/MIN
15 TO 20PCS/MIN
SEE VIDEO OF HOW THE CLIOP IS ATTACHED TO THE MASK.
DIMENSIONS OF THE MACHINE: 500mm X 500mm
WEIGHT OF THE MACHINE: 20KGS
https://youtu.be/4IGKM5TxsqY 

PACKED: IN ONE WOODEN CASE,
PACKAGE SIZE: 2000mm X 1500mm X 1900mm (L X W X H),
GROSS WEIGHT: ABOUT 1000KGS
WARRANTY OF MACHINE:1.5 YEARS
LEAD TIME IS 12 DAYS AFTER ORDER IS CONFIRMED

REFERENCE NUMBER: J-2640
DYEING AND FINISHING PLANT FOR SALE

ITEM 001
THIES SAMPLE DYEING MACHINE
MODEL: MINISOFT SAMPLE
CAPACITY: 50 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 002
THIES DYEING MACHINE
MODEL ECOSOFT PLUS
3 PORT SPLIT/SPLIT
CAPACITY: 900 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 003
THIES DYEING MACHINE
MODEL: ECOSOFT PLUS
2 PORT SPLIT/SPLIT
CAPACITY: 600 KGS
YEAR: 1999
MICROPROCESSOR CONTROL
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 004
THIES DYEING MACHINE
MODEL ECOSOFT PLUS
1 PORT SPLIT/SPLIT
CAPACITY: 300 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: A460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 005
GASTON COUNTY DYEING MACHINE
MODEL: AQUAFLOW
2 PORT
CAPACITY; 250 KGS
YEAR: 1987
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING AND UNLOADING REEL
QUANTITY: 1

ITEM 006
THIES DYEING MACHINE
MODEL: SOFT TRD
2 TUBE
CAPACITY: 700 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 007 (also our J-2647)
LAFER OPEN WIDTH COMPACTOR MACHINE
MODEL: KSA 500 2400/2200
YEAR: 1998
LAFER TEXEN CONTROLS
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION BAR ENTRY TO LATTICE ROLL GUIDER
• OPERATOR’S PLATFORM
• PUP TENTER WITH KNIT ENTRY, VERTICAL PIN CHAIN, WITH PLATE GUIDES, RAIL OPENING, PINNING BRUSHES, PINS ONLY, WITH SUPPORT SECTION FOR THE FABRIC IN THE CENTER, AT 10’ THERE IS A STEAMING SECTION, TOTAL LENGTH OF THE TENTER IS 30’, WITH AUTOMATIC LUBRICATION FOR THE CHAIN
• KSA 500 COMPACTOR BENCH WITH TEXEN CONTROLS
• TENSIONLESS FABRIC CONVEYOR
• PLAITOR AND FABRIC SCRAY WITH OPTICAL LOAD SENSOR
• INLINE INSPECTION BATCHER MACHINE, WITHH A BACK LIGHTED BOARD, MANUAL CUT
• SCALE TO WEIGHT THE FABRIC
QUANTITY: 1

ITEM 008 (also our J-2648)
SANTEX TUBULAR 4-ROLL EXTRACTION PAD
MODEL: SANTASTRETCH PLUS 140
YEAR: 1998
COMPOSED OF TURNTABLE, DETWISTER, TUBULAR 4-ROLL PAD WITH WET SPREADERS, PLAITOR
WITH ADDITION TANKS FOR SOFTENER
REEL FABRIC PLAITOR EXIT
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

ITEM 009
SANTEX CONVEYOR DRYER FOR OPEN WIDTH AND TUBULAR FABRIC
MODEL: SANTASHRINK 4/5240
YEAR: 1998
SANTEX CONTROLS
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION BAR ENTRY TO LATTICE ROLL GUIDER TO
• (2) SANTEX 2-ROLL PADS, RUBBER OVER RUBBER, 102” WIDE x 12” DIAMETER, STAINLESS STEEL PAN, 10-TON PAD, SWING-AWAY PAN, TENSION BAR WITH 2 STAINLESS STEEL MIXING TANKS, 75 GALLONS EACH
• DRIVEN SCROLL ROLLS WITH EDGE GUIDE CONTROL, WIDTH 95”
• OPERATOR’S PLATFORM
• PUP TENTER WITH KNIT ENTRY 45°, YEAR 1998, VERTICAL PIN CHAIN, 30’ LONG WITH TANDEMATIC PLATE GUIDES, RAIL GUIDES, PINNING BRUSHES, GUIDE SUPPORT FOR THE FABRIC, FABRIC CONVEYOR TO ENTER BOTH TUBULAR OR OPEN WIDTH FABRIC TO
• CONVEYOR DRYER 100” WIDE, 5 ZONES, 3-PASS WITH MAXON BURNERS, 5 CIRCULATING FANS TO CONVEYOR BELT TO PLAITOR
• ALL MOTORS AND SANTEX CONTROLS AND MONITORS
QUANTITY: 1

ITEM 010
SANTEX AG TUBULAR COMPACTOR MACHINE
MODEL: SANTASPREAD 140
YEAR: 1998
SANTEX CONTROLS
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSIONS BAR ENTRY
• OPERATOR’S PLATFORM
• TENSION DEVICE
• DRIVEN SPREADER BARS
• STEAMING DEVICE
• TUBULAR COMPACTING BENCH
• FELT BLANKET ONTO THE CONVEYOR BELT
• PRECISION PLAITOR
• TABELTOP ELECTRONIC SCALE
QUANTITY: 1

ITEM 011
COMET NAPPER
MODEL: PEGSO-X4
YEAR: 1998
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
24 ROLLS WITH TURNING BARS FOR TUBULAR 90” WIDE
XYCOM CONTROLS
12-BAG COLLECTION SYSTEM AND PLAITOR
YEAR: 1996
QUANTITY: 1

ITEM 012
STENTEX TENTER FRAME
MODEL: STENTOTHERM 3300
YEAR: 1999
STENTEX CONTROLS
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION ENTRY TO TEXT-STAR TYPE GUIDER TO 2 ROLL PAD
• ADDITION TANK TOP SCRAY PAD TO TEXT-STAR TYPE GUIDER
• TWO ROLL PAD R/R 10 TON
• OPERATOR’S PLATFORM
• WORKING WIDTH 1800mm
• HORIZONTAL PIN CHAIN, KNIT ENTRY
• TANDEMATIC SPLITLEVEL DECURLERS
• OVERFEED
• PINNING BRUSHES
• STEAM BOX
• RAIL GUIDERS, 20 FEET ENTRY, 8 ZONES
• 80 FEET HOUSING
• SCREEN MONITORS
• GAS FIRED, MAXON OVEPAK 408 BURNERS
• HONEYWELL CONTROLS
• 3 FEET COOLING ZONE
• 2 COOLING CANS, SELVEDGE TRIMMERS
• PLIATOR, SCRAY
• ZONE IN LINE INSPECTION BATCHER
QUANTITY: 1

ITEM 013
ZIMMER ROTARY SCREEN PRINTING MACHINE
MODEL: R92-S153
YEAR: 1993
COMPOSED OF:
• TENSION BAR SKY ENTRY
• SCRAY
• CORINO BRUSH
• CORINO PRINT GUIDER
• ZIMMER PRINTER, 8 COLOR, 86” BLANEKT
• PRINT CONVEYOR DRYER, 30’ LONG, 3-ZONE, GAS FIRED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

ITEM 014
SAFETY SWITCH BULLET NOSE SLITTER
MODEL: CUTTING
WITH REEL FABRIC PLIATOR
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

FOR FILLING DOWN FEATHER PILLOWS
FILLING RANGE: 1 TO 120 GRAMS (70% FEATHER & 30% DOWN)
WEIGHING SYSTEM: 4 SETS
POWER: 4.5 KW
VOLTAGE: 220 / 380 V, 3-PHASE
AIR PRESSURE: 0.5 TO 0.7 MPA
ACCURATE WEIGHING RESULTS WITH TOLERANCE OF ONLY 1 GRAM
WORKING TABLE DIMENSIONS: 1200 x 2400mm (FOR CUSTOMERS FILLING PILLOWS AND QUILTS)
WORKING TABLE DIMENSIONS FOR PILLOWS ONLY: 1200 x 1200mm (EASIER TO FIT IN A 20 FOOT CONTAINER)
OPERATION CAN BE HANDLED BY ONLY 1 EMPLOYEE
INCLUDES ONE AUTOMATIC FILLING TABLE WITH FOOT SWITCH AND CLAMP DEVICE
THE WORKER STEPS ON THE FOOT SWITCH AND THE CLAMP DEVICE WILL RUN TO CLAMP THE PILLOW BAG
THE FILLING PROCESS AUTOMATICALLY STARTS TO FILL THE PILLOW AND AFTER FINISHING THE CLAMP DEVICE WILL RESET
DURING THIS PERIOD, THE WORKER MAY SEAL THE PILLOW WITH SEWING MACHINE
FOUR HOPPER SYSTEM FOR CONSTANT SUPPLY
ONE KEY FOR CHARGE AND RECHARGE REDUCES WASTED TIME
HIGH-QUALITY, RELIABLE ELECTRICAL COMPONENTS
PREPROGRAMMABLE FOR UP TO 50 GROUPS OF RECIPES WITH EACH RECIPE CONTAINING UP TO 60 SETS OF DIFFERENT FILLING PARTS FOR THE SAME PRODUCTION
FULLY ENCLOSED DESIGN TO KEEP ENVIRONMENT CLEAN AND REDUCE MATERIAL WASTE
AUTOMATIC, ACCURATE WEIGHING WITH LOAD CELL TO ENSURE PRODUCTION QUALITY
CE CERTIFICATE INCLUDED
FLOORSPACE 4000mm LONG X 3000mm WIDE X 2500mm HIGH
TABLE FOR PILLOWS IS 1200 X 1200mm

QUANTITY: 1

REDUCES VOLUME FOR STORAGE AND TRANSPORTATION
USES COMPRESSED AIR AND PLASTIC COMPOSITE FILM BAGS FOR PACKAGING ITEMS AFTER COMPRESSION
EQUIPPED WITH AUTOMATIC TRANSMISSION TO COMPRESS AND FILM ITEMS UNINTERRUPTED
STANDARD MODEL EQUIPPED WITH ONE WORKSTATION WITH SINGLE SEAL (OPTIONAL ONE WORKSTATION WITH DOUBLE SEALS)
PLC TOUCH SCREEN OPERATION, USER FRIENDLY INTERFACE
CONSTANT TEMPERATURE CONTROL FUNCTION TO PREVENT BAG BURNS

VOLTAGE AND POWER: 220 V SINGLE-PHASE, 0.5 KW, 50 Hz
AIR PRESSURE: 0.4 – 0.8 MPA
PACKING CAPACITY: : 8 TO 12 ITEMS PER MINUTE
PRESS BOARD SIZE: LENGTH 700mm x WIDTH 900mm
MAXIMUM COMPRESSION THICKNESS: 500mm (AIR CYLINDER TRAVEL)
SEAL LENGTH: 880mm x 10mm
OVERALL DIMENSIONS: LENGTH 3390mm x WIDTH 940mm x HEIGHT 2010mm
POWER: 1.5 KW
NET WEIGHT: 350 KG
GROSS WEIGHT: 400 KG

QUANTITY: 1

REFERENCE NUMBER: L-4796
BRAND: RIETER
MODEL: C-60
CAN DIAMETER: 1000mm
CAN HEIGHT: 1200mm WITH CASTORS

C-5163 SPINNING MILL BLOW ROOM TRÜTZSCHLER & BLOW ROOM RIETER

ITEM 001
CONDENSER LVSA-375
YEAR: 1997
QUANTITY: 1

ITEM 002
MULTIMIXER MCM 6 /1200
YEAR 1997
CVT-4 / 1200
YEAR: 1997
QUANTITY: 1

ITEM 003
JOSSI THE VISION SHIELD FIBER DETECTOR EA-33-S
YEAR: 2002
QUANTITY: 1

ITEM 004
DUSTEX DX 385
YEAR: 1997
QUANTITY: 1

ITEM 005
JOSSI THE SHIELD HIGH PERFORMANCE FIRE DETECTOR
TYPE D-11-250
YEAR: 2005
QUANTITY: 1

ITEM 006
TRÜTZSCHLER FAN
QUANTITY: 3

ITEM 007
MRO METAL DETECTOR
QUANTITY: 1

BLOW ROOM RIETER
ITEM 008
UNIFLOC A 1/2
LENGTH USEFUL 20M
YEAR: 1991
QUANTITY: 1

ITEM 009
FINE OPENER FOR WASTE
WIDTH 0.80M
MODEL: B 3/4S
YEAR: 1991 + APRON 4M
QUANTITY: 1

ITEM 010
MONOTAMBOR B 4/1
YEAR: 1991
QUANTITY: 1

ITEM 011
UNIMIX B 7/3R
YEAR: 1991 (OPENER)
QUANTITY: 1

ITEM 012
ERM B 5/5
YEAR: 1989
QUANTITY: 2

ITEM 013
JOSSI FIRE DETECTOR D-11-250
YEAR: 2005
QUANTITY: 1

ITEM 014
JOSSI THE VISION SHIELD DETECTOR
FIBER DETECTOR TYPE EA-33-S
YEAR: 2002
QUANTITY: 1

ITEM 015
CARDS TRÜTZSCHLER DK-803
YEAR: 1997
COILER KH 950-1200
AUTOMATIC REVOLVER
FEEDING FBK-533
QUANTITY: 3

ITEM 016
CARDS TRÜTZSCHLER DK-903
YEAR: 2003
1 COILER KH 600-1200
2 COILER KH 450-1200
AUTOMATIC REVOLVER
FEEDING DKF
QUANTITY: 3

ITEM 017
DRAW FRAME TRÜTZSCHLER HSR-1000
YEAR: 2003
DELIVERY 18” (450X1000)
CREEL 8 CANS
SLIVER MONITOR
AUTOLEVELLER
QUANTITY: 2

ITEM 018
ROVING FRAME SIMPLEX ZINZER 670
YEAR: 2003
DRAFT PK 1500
120 SPINDLES
CAPACITY BOBBIN 16”X6”
DRIVER CREEL
COLLECTIVE ASPIRATION
INDIVIDUAL BLOWER ELECTRO-JET
QUANTITY: 2

ITEM 019
AUTOMATIC TRANSPORT INSTALLATION FOR BOBBINS ELECTRO-JET
YEAR: 2003
FOR 8 RING SPINNING FRAME
1,200 SPINDLES
QUANTITY: 2

ITEM 020
INSTALLATION LTG
YEAR: 2003
5 PARTS
WASTE COLLECTING
AIR SYSTEM
QUANTITY: 1

ITEM 021
INSTALLATION LTG
YEAR: 2003
3 PARTS
WASTE COLLECTING
AIR SYSTEM
QUANTITY: 1

ITEM 022
INSTALLATION LTG
YEAR: 2003
5 PARTS
WASTE COLLECTING
CARDING FILTRATION
QUANTITY: 1

ITEM 023
RING SPINNING FRAME ZINZER RM 351
YEAR: 2002 (4)
YEAR: 2003 (1)
1200 SPINDLES
GAUGE 70MM
DRAFT PK 2500
RING 42MM
TUBE 220MM
COWEMAT
COLLECTIVE ASPIRATION
INDIVIDUAL BLOWER
ELECTRO-JET WITH AUTOMATIC UNLOADING
TOTAL LENGTH 47M
QUANTITY: 5

ITEM 024
WINDER SCHLAFHORST 338 RM
YEAR: 2003
COLOR WHITE
60 POSITIONS
MAGAZINE FEEDING 6 TUBES
2 ROBOTS
WAXING
AUTOMATIC CONE CHANGE
TK-840
CLEARER LOEPFE
DELIVERY 4.20 X 6”
INDIVIDUAL BLOWER
QUANTITY: 2

ITEM 025
AUTOCORO SCHLAFHORST SE-11 ACO-288
YEAR: 2001
216 ROTORS
INFORMATOR
DELIVERY CYLINDRICAL SLUBIER PINTER
ROTOR Ø 28-36-40MM
ROLLERS B-174
CLEARERS COROLAB
WAXING
2 ROBOTS CONE CHANGE ROBOTS PIECERS
QUANTITY: 1

ITEM 026
AUTOCORO SCHLAFHORST SE-9
YEAR: 1998
216 ROTORS
2 ROBOTS
WAXING
COROLAB
INFORMATOR
QUANTITY: 1

ITEM 027
POWER 380V/50HZ
SPLIT SALE POSSIBLE
CONDITION COMPLETED
UNIT PRICE EX-WORKS EURO

C-2910 TOYOTA RX 240 RINGFRAME WITH 1008 SPINDLES, RING DIAMETER 44mm, YEAR 1996

TOYOTA RINGFRAME
MODEL: RX 240
YEAR: 1996
NUMBER OF SPINDLES: 1008
GAUGE: 70mm
CRADLE: SHORT
TOPARMS: SKF PK 2025
SUCTION: FLUTE TYPE PNEUMAFILL
DOFFER: AUTOMATIC
TOP ROLLER CLEARER: AVAILABLE
CREEL: 5 ROW
OHTC: ELECTROJET
RING DIAMETER: 44mm
WHARVE DIA: 18.5mm
TUBE LENGTH: 210mm
MAIN MOTOR: 45 KW

QUANTITY: 5