Search results for: 'reference nu''

REFERENCE NUMBER: T-6552

MASK AIR TIGHTNESS TESTER

MASK AIR TIGHTNESS TESTER

HOW TO CHOOSE A HIGH-QUALITY MASK NOT ONLY DEPENDS ON THE FILTERING EFFICIENCY OF THEMASK, BUT ALSO TO CONFIRM WHETHER THE MASK IS COMPLETELY IN CONTACT WITH THE FACE, OTHERWISE AEROSOL PARTICLES SUCH AS GERMS THAT HAVE NOT BEEN FILTERED BY THE MASK WILL BE INHALED FROM THE INADEQUATE ADHESION. THEREFORE, IT IS VERY IMPORTANT TO CHECK THE WEARING STATUS OF THE MASK. THE EUROPEAN AND AMERICAN COUNTRIES HAVE LISTED THE APPLICATION TEST OF THE MASK AS A STRONG INSPECTION ITEM.

FOR EXAMPLE, THE N95 MASK IS ONE OF 9 TYPES OF PARTICULATE PROTECTIVE MASKS CERTIFIED BY NIOSH (NATIONAL INSTITUTE OF OCCUPATIONAL SAFETY AND HEALTH). "N" INDICATES OIL RESISTANCE."95" INDICATES THAT THE PARTICLE CONCENTRATION IN THE MASK IS MORE THAN 95% LOWER THAN THAT OF THE PARTICLES OUTSIDE THE MASK WHEN EXPOSED TO THE SPECIFIED NUMBER OF SPECIAL TEST PARTICLES. N95 IS NOT A SPECIFIC PRODUCT NAME, AS LONG AS IT MEETS THE N95 STANDARD AND PASSES THE NIOSH REVIEW, IT CAN BE CALLED "N95 MASK".

N95 TYPE MASKS, IN ADDITION TO THE FILTERING EFFICIENCY OF THE MASKS, THE CLOSENESS OF THE MASKS TO THE FACE IS ONE OF THE IMPORTANT FACTORS THAT DETERMINE THE EFFECTIVENESS OF THE USE OF THE MASKS. THE SUITABILITY OF DIFFERENT TYPES OF MASKS FOR THE HUMAN FACE VARIES GREATLY.

THEREFORE, BEFORE USING A MASK, THE SUITABILITY OF THE MASK SHOULD BE CHECKED FIRST. DURING THETIGHTNESS TEST OF THE WEARER'S FACE, ENSURE THAT AIR CAN PASS IN AND OUT THROUGH THE MASK WHEN IT IS CLOSE TO THE EDGE OF THE FACE. THE MASK TIGHTNESS TESTER CAN QUICKLY COMPLETE THE TIGHTNESS TEST OF RESPIRATORS SUCH AS MASKS TO ENSURE THAT IT PROVIDES GOOD PROTECTION PERFORMANCE. IT CONFORMS TO THE CHINESE RESPIRATOR STANDARD GB2626-2019 STANDARD, OSHA / CSA STANDARD AND CHINA GENERAL ADMINISTRATION OF QUALITY SUPERVISION, INSPECTION AND QUARANTINE "GB 19083-2010 TECHNICAL REQUIREMENTS FOR MEDICAL PROTECTIVE MASKS" JOINTLY ISSUED BY THE CHINA NATIONAL STANDARDIZATION ADMINISTRATION COMMITTEE.

ADHESION (SUITABILITY TEST): THE MASK DESIGN SHOULD PROVIDE GOOD ADHESION. THE OVERALL FIT FACTOR OF THE MASK SHOULD NOT BE LESS THAN 100. THIS TEST THE REQUIREMENTS WERE FORMALLY IMPLEMENTED ON AUGUST 1, 2011.

BENNINGER
MODEL: ZCR
WARPING MACHINE
YEAR: 1995
MODEL: BEN-PROCOM
SIZING MACHINE
YEAR: 1995
QUANTITY: 2

K-2582 SIEMENS COAL AND BIOMASS POWER PLANT 2.5MW YEAR 2002

WAS BUILT TO SUPPLY THE PAPER MILL WITH STEAM AND ELECTRICITY

MAKE: SIEMENS
MODEL: CFR5 G6a
2.5MW
65 BAR
480 ˚ C
REVOLUTION NUMBER: 23000 U PER MINUTE
EVAPORATION PRESSURE: 1-10 BAR
YEAR 2002
THE STEAM TUBINE AND THE GENERATOR WERE CHANGES AND ARE NEW
HOURS: LESS THAN 30,000
BOILER SYSTEM WAS COMPLETELY RECONDITIONED
THE WATER TREATMENT PLANT WAS RECONDITIONED
EXHAUST CLEANING SYSTEM WAS RECONDITIONED
ASH AND COAL TRANSPORTATION SYSTEMS WERE RECONDITIONED

QUANTITY: 1

REFERENCE NUMBER: M-3703

LAROCHE TEARING MACHINE

TEARING MACHINE

4 DRUMS

LAROCHE

MACHINE IN VERY GOOD CONTION

WIDTH OF DRUMS: 1000mm

NUMBER OF PINS PER SQUARE INCH

CYLINDER  1:      11 PINS

CYLINDER 2:       15 PINS

CYLINDER 3:       15 PINS

CYLINDER 4:       15 PINS

DIMENSIONS OF LAG : 106mm x 85mm

MOTORS

MOTOR CYLINDER 1:      55CV

MOTOR CYLINDER 2:      55CV

MOTOR CYLINDER 3:      40CV

MOTOR CYLINDER 4:      30KW

3 CYLINDERS YEAR 1984

ONE CYLINDER YEAR 1997

THERE IS AN EXTRA ROLL WITH 18 PINS BY INCH

THERE ARE 34 LAGS FOR EACH CYLINDER  

THERE IS ONE MOTOR EACH CYLINDERNOTHI

EACH MACHINE HAS FAN INCLUDED

REFERENCE NUMBER: M-4074

BARMAG SPINNING PLANT FOR POLYESTER YEAR 2000 – CAPACITY 20 TONS/DAY – 24 ENDS

BARMAG SPINNING FOR POLYESTER

INSTALLATION  YEAR 2000

MACHINE CAPACITY  20 TON DAY

NUMBER ENDS 24

EXTRUDER BARMAG

SPIN PUMPS BARMAG

FINISH PUMPS BARMAG

BOILER BARMAG

WINDER BARMAG

MAX BOBBIN 15 KG

PRODUCTION POY - HOY -SDY

IMPORTANT UNTIL N. 11 DIFFERENT COLOURS (WITH MASTER )

PARTS PLANT:

CHILLER - CDZ CANALAIR - AUTODOFFER GUALCHIERANI - COOLING TOWERS EVAPCO - SILOS ALLUMINIUM - SPARE PARTS

* DISMANTLING AND LOADING IS INCLUDED *

QUANTITY: 1

C-4026 NUOVO PIGNONE GAS TURBINE, 11 MW AND CONDENSING TURBO GENERATOR SETS, 44.5 MW, YEAR 2002

OFFER 001
11.7 MWE GAS TURBINE-GENERATOR SETS
GAS TURBINES
MANUFACTURER: NUOVO PIGNONE
MODEL: PGT10B-1
TYPE: MULTI-SHAFT, HEAVY DUTY GAS TURBINE
FUEL: NATURAL GAS

OFFER 002
ALTERNATOR
MANUFACTURER: ANSALDO
APPARENT POWER: 13,569 KVA
ACTIVE POWER: 11,000 KW
POWER FACTOR: 0.8
RATED SPEED: 1,500 RPM

OFFER 003
65.7 TPH WASTE HEAT RECOVERY BOILERS
BOILERS
MANUFACTURER: MACCHI
THERMAL RATING: 55,330 KW
NET THERMAL EFFICIENCY. COP: 90.32%
NET THERMAL EFFICIENCY. COV: 92.48%

OFFER 004
44.5 MW CONDENSING TURBO-GENERATOR SET
STEAM TURBINE
MANUFACTURER: NUOVO PIGNONE
MODEL NUMBER: HNK 50/3.2
CONFIGURATION: 1 IMPULSE STAGE 62 REACTION STAGES
RATED POWER: 44,500 KW
RATED INLET FLOW: 131,400 KG/H

OFFER 005
GENERATOR
MANUFACTURER: JEUMONT INDUSTRIE
RATED APPARENT POWER: 51,500 KVA
POWER FACTOR: 0.8
ACTIVE POWER: 41,200 KW

OFFER 006
CONDENSER
MANUFACTURER: CALDEMON
TYPE: SURFACE CONDENSER

QUANTITY: 2