Search results for: 'back'

REFERENCE NUMBER: P-2366 MURATA MODEL 7R2 MAGAZINE FED BACKWINDERS 5 SPINDLES MURATA 7R2 MAGAZINE FED BACKWINDERS 5 SPINDLES QUANTITY AVAILABLE: 1 Learn More

R-1695 TRUTZSCHLER DK903 IDF CARDING, YEAR 2002

ITEM 001
TRUTZSCHLER DK903 IDF CARDING
MAKE: TRUTZSCHLER
MODEL: DK903 IDF
YEAR: 2002
INTEGRATED DRAW FRAMES: AVAILABLE
CCD: AVAILABLE
CFD: AVAILABLE
CHUTE FEED TYPE: DFK
CAN HEIGHT: 45”
WASTE COLLECTION: CONTINUOUS
EXHAUST / WASTE SUCTION: UPWARDS
NO OF LICKER IN: 3
FLAT TYPE: ALUMINUM
ST FLAT FRONT: 2
ST FLAT BACK: 3
MATERIAL PROCESS: COTTON

QUANTITY: 12

ITEM 002
TRUTZSCHLER DK903 IDF CARDING
MAKE: TRUTZSCHLER
MODEL: DK903 IDF
YEAR: 2002
INTEGRATED DRAWFRAME: AVAILABLE
CCD: AVAILABLE
CFD: AVAILABLE
CHUTE FEED TYPE: DFK
CAN HEIGHT: 45”
WASTE COLLECTION: CONTINUOUS
EXHAUST / WASTE SUCTION: UPWARDS
LICKER IN: 3
FLAT TYPE: ALUMINUM
ST FLAT FRONT: 3
ST FLAT BACK: 5
MATERIAL PROCESS: SYNTHETIC

QUANTITY: 4

Learn More

REFERENCE NUMBER: YY-1365 CONTINUOUS PRODUCTION LINE FOR IMPREGNATION, DRYING, ABRASIVE SPRAY, HEAT-SETTING OF SYNTHETIC FIBERS FOR ABRASIVE WADDINGS, WITH AIRLAY CARDING MACHINE AND FIBER PREPARATION DETAILS: MAIN FEATURES: - THREE LAYERS OVEN: TWO UPPER DRYING LAYERS WITH LENGTH OF 6+ 6 METERS; ONE LOWER CURING LAYER WITH A LENGTH OF 6 METERS; - HEATING: BY DIRECT HEATING WITH AUTOMATIC BURNERS; - CONVEYOR WIDTH: 2200mm; - WORKING WIDTH: 2000mm; - MAX DRYING AND POLYMERISATION TEMPERATURE: 230°C; - HEATING POWER: 4 BURNERS 350 KW EACH ONE, ABOUT TOTAL 1.400 KW; - VENTILATION: SEMI-CLOSED SYSTEM WITH 4 CENTRIFUGAL VENTILATORS; - ADJUSTABLE CONVEYOR SPEED BY A.C. MOTORS; - INSTALLED ELECTRIC POWER: 200 KW. APPROX.; - MECHANICAL SPEED: 2÷15 METERS PER MINUTE; - CONVEYOR DRIVING: BY A.C. MOTORS; - MANUFACTURED ARTICLE: SYNTHETIC FIBERS ABRASIVE WADDING. Learn More

REFERENCE NUMBER: A-2471 INDUSTRIAL ELECTROSPINNING MACHINE A MASS PRODUCTION MACHINE OF ELECTROSPINNING. ALUMINUM FRAME STRUCTURE MAKES IT POSSIBLE FOR EXTENDING DIFFERENT FUNCTIONS. THE SPINNERET USED IS MULTI-NEEDLE ARRAYS, FROM 64 TO 384 NEEDLES ARE EQUIPPED. THE LENGTH AND WIDTH CAN BE MADE ACCORDING TO CUSTOMER'S REQUIREMENT. ROLL TO ROLL COLLECTOR AND CONTINUOUS COLLECTOR CAN BE USED BASED ON THE THICKNESS OF REQUIRED FIBER SHEET. FOR SOLUTIONS, A MULTI-CHANNEL PUMP WILL BE SUPPLIED FOR LONG TIME PRODUCTION OR NONE-STOP PRODUCTION. FEATURES: － EQUIPPED WITH BOTH POSITIVE & NEGATIVE HIGH VOLTAGE SUPPLY DEVICES － EQUIPPED WITH UNWINDING & WINDING MACHINES － CONTINUOUS ELECTROSPINNING & WINDING － ALUMINUM ALLOY FRAME STRUCTURE, MULTI-FUNCTIONS EXPANSIBLE － MULTI-NEEDLES IN ARRAYS. 16 NEEDLES X N ROWS, UP TO 384 NEEDLES － SPINNERET MOVING MACHINERY ENSURES EVEN FIBER SHEET － ONLINE AUTO-CLEAN DEVICE FOR NEEDLES － THICKNESS OF THE FIBER SHEET IS CONTROLLABLE － CE & FCC CERTIFICATE SPINNERET STANDARD：16 NEEDLES X 8 GROUPS =128 NEEDLES (THE NUMBER OF NEEDLES CAN BE ADJUSTED FREELY ACCORDING TO THE REQUIREMENTS OF USE） X-Y-Z MOTION SYSTEM － THE NOZZLE CAN BE MOVED UP AND DOWN IN THE Z DIRECTION THROUGH THE TOUCH SCREEN CONTROL TO DETERMINE THE APPROPRIATE SPINNING DISTANCE. － THE NOZZLE CAN MOVE BACK AND FORTH ALONG THE YAXIS DIRECTION OF THE TANGENT DIRECTION OF THE RECEIVING FILM TO PREPARE A UNIFORM FIBER FILM. － THE NOZZLE AUTOMATIC ONLINE CLEANING DEVICE SCANS ALONG THE X-AXIS DIRECTION. COLLECTOR － STAINLESS STEEL PLATE / MESH SERVES AS A CARRIER FOR THE FIBER MEMBRANE SUBSTRATE. － CONNECTED WITH NEGATIVE HIGH VOLTAGE. － RECEIVER BOARD WIDTH: 500 mm － SPINNING DISTANCE: 80 TO 300 mm ADJUSTABLE WINDER AND UNWINDER － AUTOMATICALLY CALCULATE THE ROLL DIAMETER OF THE LOADED MATERIAL AND CONTROL THE TENSION BETWEEN THE UNWINDING AND SPINNING SECTIONS. － CONSTANT FEEDING SPEED. THE FEEDING SPEED RANGE IS 0 TO 5000 mm / min. － ONLINE HOT PRESSING FUNCTION MODULE. AFTER THE SPINNING IS COMPLETED, BEFORE THE WINDING, A TEMPERATURE-CONTROLLED HOT PRESSING DEVICE (ROOM TEMPERATURE TO 60 ° C) IS USED FOR HOT PRESSING. (OPTIONAL THIRD LAYER MATERIAL STICKING AND REWINDING DEVICE). － CAN BE OPERATED BY TOUCH SCREEN. － DO NOT USE METAL FILM AS THE RECEIVING CARRIER. SYRINGE PUMP － 200ML X 4N CHANNEL － FLOW RATE: 0.1ML / H TO 1280 ML / H － SPECIALLY DESIGNED FOR ELECTRO-SPINNING AND RESISTANT TO HIGH VOLTAGE. HIGH VOLTAGE DEVICE －0 TO 50KV, DIGITAL DISPLAY －-50KV ~ 0 KV, DIGITAL DISPLAY －OUTPUT CURRENT: <1 MA －CONTINUOUSLY ADJUSTABLE CONTROL SYSTEM －PLC CONTROL SYSTEM, 7-INCH TOUCH SCREEN. －CONTROL THE MOVEMENT OF THE NOZZLE. －CONTROL THE NOZZLE TO MOVE UP AND DOWN. －YOU CAN SET THE MOVEMENT TIME, STROKE AND SPEED OF THE NOZZLE. －CONTROL THE FREQUENCY OF NOZZLE CLEANING. －SPINNING PROCESS PARAMETER RECORDS. ENVIRONMENTAL CONTROL SYSTEM －PROVIDE INTERFACE TO LET IN DRY AMBIENT HUMIDITY AIR. －AN EXTERNAL DEHUMIDIFIER CAN BE USED TO CONTROL THE AMBIENT HUMIDITY. THE EXTERNAL DEHUMIDIFIER NEEDS TO BE SELECTED ACCORDING TO THE SIZE OF THE WORKSHOP. THIS EQUIPMENT DOES NOT INCLUDE THIS DEHUMIDIFIER. EXHAUST SYSTEM －BOTTOM UP, AND FOUR FANS ARE PUMPED AT THE SAME TIME. －THE DISCHARGE VOLUME OF A SINGLE UNIT IS 5 TO 150 M3 / H, AND THE RATE IS ADJUSTABLE. THE COMBINED DISCHARGE VOLUME OF THE TWO EXHAUST FANS IS 10 TO 300M3 / H. THE EXTRACTOR IS DRAWN FROM THE MIDDLE. IN THIS WAY, THE HIGH-SPEED AIR VENTILATION MINIMIZES THE RELATIVE DISTURBANCE TO THE SPINNING. THE EXHAUST FAN IS A SILENT EXHAUST FAN. SAFETY －AUTOMATIC POWER-OFF DEVICE FOR OPENING THE DOOR. －RESIDUAL STATIC ELECTRICITY REMOVAL DEVICE. －EMERGENCY STOP SWITCH. －GROUND AT MULTIPLE POINTS. －ALARM DEVICE AFTER THE CONTROL PARAMETERS EXCEED THE LIMIT. CHAMBER －THE CHAMBER IS MADE OF ALUMINUM ALLOY FRAME. －THE FRONT AND SIDE WINDOWS OF THE CABINET ARE MADE OF TEMPERED GLASS. －MULTI-POINT TEMPERATURE AND HUMIDITY COLLECTION AND DISPLAY. －THE PROCESS CAN BE OBSERVED WITH THE NAKED EYE. －AIR INLET: HOT AND DRY AIR CAN BE INTRODUCED TO QUICKLY ADJUST THE HUMIDITY INSIDE THE CHAMBER. POWER SOURCE －220 VOLTS AND 50/60 Hz －TOTAL POWER: 10KW NUMBER OF NEEDLES: 128 NEEDLES (THE NUMBER OF NEEDLES CAN BE ARBITRARILY REDUCED ACCORDING TO THE SOLVENT USAGE) FLOW RATE OF EACH NEEDLE: (~ 3ML ± 50%) / HOUR TOTAL FLOW OF THE WHOLE MACHINE: ABOUT (400ML ± 50%) / HOUR SOLUTION CONCENTRATION: 10 TO 20% 8 HOURS SOLUTION PROCESSING CAPACITY: ABOUT (3L ± 50%) / 8 HOURS SOLID CONTENT (WEIGHT OF FIBER PRODUCED): (300G ± 50%) / 8 HOURS ACCORDING TO THE APPROXIMATE PRODUCTION OF FIBER MATERIAL WITH A GRAM WEIGHT OF 2GSM. WINDING AND UNWINDING SPEED: 50M / H MATERIAL WIDTH: 0.5 METERS FABRIC AREA PRODUCED PER HOUR: 25 SQUARE METERS FABRIC AREA PRODUCED IN 8 HOURS: 200 SQUARE METERS FABRIC AREA PRODUCED IN 24 HOURS: 600 SQUARE METERS BASED ON THE PRODUCTION OF FIBER MATERIAL WITH A GRAMMAGE OF 0.02G / ㎡, APPROXIMATELY: WINDING AND UNWINDING SPEED: 5000M / H MATERIAL WIDTH: 0.5 METERS FABRIC AREA PRODUCED PER HOUR: 2500 SQUARE METERS FABRIC AREA PRODUCED IN 8 HOURS: 20,000 SQUARE METERS FABRIC AREA PRODUCED IN 24 HOURS: ABOUT 60,000 SQUARE METERS Learn More

P-4706 TOYODA FL-100 ROVING FRAMES YEAR 1997 96 and 120 SPINDLES

TOYODA
MODEL: FL-100
ROVING FRAMES
YEAR: 1997
2 SETS WIITH 96 SPINDLES
2 SETS WITH 120 SPINDLES
STAFF (4 SPINDLES); 440mm
FULL BOBBIN DIAMETER: 152mm
LIFT: 406mm
EASY DOFFING DEVICE
DRAFTING SYSTEM: 4-ROLLER DOUBLE APRON D-TYPE
FOR 100% COTTON, COMBED OR CARDED
PROCESSING FIBRE UP TO 38mm, Ne 10-20s
WEIGHTING ARM: SKF-PK1500-001938
SHORT BOTTOM APRON
CRADLE TYPE: SKF OH 514-110
CCRADLE RADIUS: 34.5mm, WIDTH: 40mm
BOTTOM ROLLER = 28.5 (F) x 28.5 (S) x 28.5 (T) x 28.5 (B)
TOP ROLLER SKF
LP 315-110 (F) x LP 315-110 (S) x LP 317-110 (T) x LP 315-110 (B)
DIAMETER OF FLYER SPINDLE, 22mm
LIGHT ALLOW METAL FLYER, SL REINFORCED, SLIT LESS TYPE (FL 100)
SIZE OF FEEDING CAN: 508mm (20 INCHES) x 1321mm (52INCHES) SIZE
SINGLE SILVER FEEDING TYPE
INDICATOR: 3 SHIFTS
CLEARER: POSITIVE INTERMITTENT ROVING CLEARER WITH COMB FOR TOP AND BOTTOM ROLLERS
ELECTRIC CUSHION STARTER CONTROL FOR RUN AND INCHING
AUTOMATIC LUBRICATION FOR FLYER AND BOBBIN GEAR
MACHINE BACK COVER WITH BOBBIN JUMP PREVENTION DEVICE
VOLTAGE: AC 220/60Hz

SPECIAL OPTIONS INCLUDED ARE:
ROVING TENSION CONTROLLER
FLYER SPEED CONTROL BY INVERTOR
MAIN GEARING IN OIL BATH
DRAFT GEARING GREASE
IRREGULAR ROVING [REVENTING DEVICE
PACKAGE SHOULDER COLLAPSE PREVENTING DEVICE
STOP MOTION UPON LENGTH MEASURED SETTING COMPLETION

QUANTITY: 4 SETS

Learn More

P-3319 TOYODA RY-5 RING FRAME YEAR 1988, 1990 & 1991

TOYODA
MODEL: RY-5
RING FRAME
YEAR: 1988, 1990 & 1991
480 SPINDLES EACH = TOTAL 2400 SPINDLES
GUAGE: 75mm
SPINDLE WRAP DIAMETER: 20.2mm
RING DIAMETER: 42mm
DRAFT SYSTEM: SKF
BOBBIN HEIGHT: 230mm
BOTTOM ROLLER DIAMETER OF ALL 3 FRONT, MIDDLE, BACK: 25mm
CREDLE: MEDIUM (3 SETS), SHORT (2 SETS)
OVER HEAD CLEANER: WITH

QUANTITY: 5 SETS

Learn More

P-1772 TOYODA RY-5 RING FRAME YEAR 1990 480 SPINDLES

TOYODA
TYPE: RY-5
RING FRAME
YEAR: 1990
480 SPINDLES
RING GUAGE: 75mm
RING DIAMETER: 42mm
BOBBIN: 230mm
PEDRUM: SKF
SPINDLE WRAP DIAMETER: 19
DRAFTING SYSTEM: BOTTON ROLL DIAMETER OF ALL 3 FRONT, MIDDLE, BACK: 27
WITH TRAVELLING CLEANER
POWER: 440 VOLTS x 60 HZ

QUANTITY: 1

Learn More

C-2308 TOYODA RING FRAME RY-5 WITH 480 SPINDLES, DIAMETER 42mm, YEAR 1991

MODEL: RY-5
480 SPINDLES
YEAR: 1991
GAUGE: 75mm
SPINDLE WRAP DIAMETER: 20.2mm
RING DIAMETER: 42mm
DRAFT SYSTEM: SKF
BOBBIN HEIGHT: 230mm
BOTTOM ROLLER DIAMETER OF ALL 3 FRONT, MIDDLE, BACK: 25mm
CREDLE: SHORT
OVER HEAD CLEANER: WITH

QUANTITY: 1

Learn More

C-2307 TOYODA RING FRAME RY-5 WITH 480 SPINDLES, DIAMETER 42mm, YEAR 1990

MODEL: RY-5
480 SPINDLES
YEAR: 1990
GAUGE: 75mm
SPINDLE WRAP DIAMETER: 20.2mm
RING DIAMETER: 42mm
DRAFT SYSTEM: SKF
BOBBIN HEIGHT: 230mm
BOTTOM ROLLER DIAMETER OF ALL 3 FRONT, MIDDLE, BACK: 25mm
CREDLE: SHORT
OVER HEAD CLEANER: WITH

QUANTITY: 1

Learn More

C-2306 TOYODA RING FRAME RY-5 WITH 480 SPINDLES, DIAMETER 42mm, YEAR 1990

MODEL: RY-5
480 SPINDLES
YEAR: 1990
GAUGE: 75mm
SPINDLE WRAP DIAMETER: 20.2mm
RING DIAMETER: 42mm
DRAFT SYSTEM: SKF
BOBBIN HEIGHT: 230mm

QUANTITY: 1

Learn More