Search results for: 'filler'

•ITEM NO.: F-2 •DIMENSION: APPROX. 11000*2500*3000MM •VOLTAGE: 380V 50HZ 3PHASE •POWER: 11KW •FILLING RANGE: 2-100 G, DEPENDING ON THE MATERIAL •ACCURACY: ±1G •AIR PRESSURE: 0.5-0.8MPA •THERE ARE 4 WEIGHING SYSTEM AND 2 WORKING TABLE ASSEMBLED TO THE DOWN FEATHER FILLING LINE •IT IS MAINLY USED TO MAKE DOWN FEATHER QUILTING Learn More

DISPENSER SILOS FOR MATERIALS FOR SHORT STAPLE (POLYESTER, FEATHER, FOAM RUBBER, MIXTURES, ETC.) THE CYLINDRICAL SHAPED SILOS HAS GOT A CAPACITY OF 3 CUBIC METERS A MIXER, IN THE SILO, KEEPS THE MATERIAL IN MOTION AND FACILITATES IT IS GOING OUT. IT IS POSSIBLE TO CONNECT TWO FILLER MACHINE AND/OR TWO WORKSTATIONS. THE MIXER HAS “SOFT – START” DEVICE FOR A LONG LIFE OF MOTOR AND GEARBOX. ELECTRIC PLANT IN WATERTIGHT CABINET (IP 55) WITH DOOR-LOCK ISOLATOR, TELEMOTOR PROTECTOR, SAFETY END OF STROKE AND LOW-TENSION CONTROLS. Learn More

A) HOPPER MODEL L1500 MIXING SYSTEM B) OPENER MODEL F1000 – FOR THE FIRST OPENING OF THE FIBERS C)DISPENSER SILOS MODEL C5 D) SHREDDING MACHINE – SHREDDING FOAM MODEL F430 E) FILLING MACHINE WITH ELECTRONIC CONTROL WEIGHT MODEL W11 F) SPECIAL SEWING MACHINE MODEL 164C Learn More

THIS MACHINE PROVIDED WITH A BRAKING SYSTEM WHICH PERMITS THE FILLING OF WADDING PILLOWS AND QUILTS WITH ALL MATERIALS (POLYESTER, FEATHER, EXPANDED POLYURETHANE, COTTON, WOOL, ETC.) THE PARTICULAR WIDENED SHAPE OF THE TURBINE MAKES IT POSSIBLE TO OBTAIN REMARKABLE PERFORMANCES IN THE FILLING UP USING THE SPECIAL TUBE IT IS POSSIBLE TO SUCK UP THE MATERIAL DIRECTLY FROM THE VARIOUS CONTAINERS. THE BRAKING IS VERY RAPID (ABOUT 1/10 OF SECOND) AND DOES NOT REQUIRE MAINTENANCE SINCE IT IS OBTAINED THROUGH A PNEUMATIC DEVICE. THE CONTROL DEVICE IS A PNEUMATIC FOOT-LEVER WHICH LEAVES THE OPERATOR’S HANDS UNENGAGED. SAFETY MOTOR PROTECTOR SWITCH. IT CAN BE SUPPLIED BOTH IN A ONE-PHASE AND IN A THREE-PHASE VERSION. THE MACHINE IS CONSTRUCTED IN CONFORMITY WITH THE EEC DIRECTIVES 2006/42/CE, 2004/108/CE E 2006/95/CE AND SUCCESSIVE MODIFICATIONS AND MARKED CE. ON REQUEST WITH SPEED VARIATION THE FAN SPEED IS ADJUSTABLE FROM 2000 TO 4200 RPM, IN ORDER TO OPTIMIZE THE SPEED OF FILLING TO THE SHAPE AND THE SIZE OF THE PILLOW AT MAXIMUM SPEED, THE AMOUNT OF MATERIAL FILLED IS ABOUT 200 GRAMS PER SECOND. ON THE PART OF THE MACHINE THE LOAD OF THE MATERIAL, THERE ARE 2 DAMPERS. THIS PREVENTS THE OVERLOADING OF THE TURBINE AND THE BLOCK OF MATERIAL, BECAUSE WHEN I RELASE THE PEDAL, FIRST I BLOCK THE FLOW OF MATERIAL AND THEN THE AIR FLOW. THE PARTICULAR SHAPE OF THE OUTLET PIPE ALLOWS TO FILL THE PILLOWS THAT HAVE AIR-TIGHT LINING. THE TURBINE IS MADE OF A CAST ALUMINUM. THE COMMAND TO THE DUMPERS IS GIVEN BY A PEDAL, SO THE OPERATOR HAS BOTH HANDS FREE. THE APPLICATION OF THE GRIPPERS ON THE OUTLET PIPE OF THE FILLER R 3PV ALLOWS A SINGLE OPERATOR TO USE MORE FILLERS. FURTHERMORE, IT IS POSSIBLE CHANGE THE TIME THAT THE GRIPPERS STAY CLOSED. THIS ALLOWS TO SET THE AMOUNT OF MATERIAL TO PUT INSIDE HE PILLOW, WITH A GOOD PRECISION. THE TIME IS ADJUSTABLE TO FILL DIFFERENT KINDS OF PILLOWS WITH DIFFERENT AMOUNTS OF MATERIAL. QUANTITY: 1 Learn More

REFERENCE NUMBER: F-1361 PILLOW WEIGHT SETTING FILLING MACHINE FILLING MACHINES WITH PADDING DEVICES ENSURE HIGH SPEED AND TOP QUALITY FILLING. THE OPERATORS CAN SET THE WEIGHT OF EACH PILLOW/CUSHION APPROXIMATELY FIBER CARDING MACHINE: DIMENSIONS: 2150 X 1150 X 980 POWER: 6.35kW NET WEIGHT: 800kg CAPACITY: APPROX. 160 TO 190kg PER HOUR VOLTAGE: AS PER CUSTOMER OFFERS MORE SAFETY: THE FIBER CARDING MACHINE HAS AN OVERLOADING ALARM SYSTEM TO AVOID THE MACHINE BEING DAMAGED SAVES ON COSTS: IF AN ADDITIONAL BALE OPENING MACHINE IS ADDED, ONLY ONE PERSON IS NEEDED TO RUN THE WHOLE LINE WITH TWO FILLER HEADS FILLING MACHINE: DIMENSIONS: 3350 X 1900 X 1450 POWER: 4.74kW NET WEIGHT: 400kg AIR PRESSURE: 1mpa CAPACITY: APPROX. 160 TO 190kg PER HOUR VOLTAGE: AS PER CUSTOMER QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: K-9222-A

ORMONT BLOWER AND HOPPER YEAR 1996

 

ORMONT PILLOW FILLER AND HOPPER

YEAR 1996

 

ORMONT CORPORATION SHREDDER

TYPE: TRP

SIZE: 11

HP: 11

RPM: 1750

VOLTS: 575

PHASE: 3

CYCLE: 60

AMPS: -

SERV: 80388

FRAME: 1143T

MOTOR INFO:

BRAND: LEESON

HP: 15

VOLTS: 208-230/460

RPM: 1765

PLATE INFO:

ORMONT CORPORATION BLOWER – ONE NOZZLE

TYPE: FG

SIZE: 36

HP: 15

RPM: 1750

VOLTS: 220

PHASE: 3

CYCLE: 60

AMPS: 22

SERV: 80488

FRAME: 254T

 

QUANTITY: 1

Learn More

GREIGE 1. 80 GRAM STITCH BOND 2. 100 GRAM STITCH BOND 3. 130 GRAM STITCH BOND FR FINISHED FILLERCLOTH 1. THREE DIFFERENT QUALITIES OF FR FILLER CLOTH 2. NUMEROUS PATTERNS IN FR PRINTED STITCH BOND AND NON FR STITCH BOND Learn More

MACHINE DIMENSIONS: 2200 X 800 X H. 1550 CM NET WEIGHT: 180 KG POWER: 380V THREE PHASE KW. 2.5 COMPRESSED AIR: 3 BARS COMMODITY CODE: 8445.19.29 Learn More

REFERENCE NUMBER: M-4747 (1111NBRTHH10) L INDUSTRIAL BREWERY WITH BREWHOUSE 20 HL INDUSTRIAL BREWERY WITH CAPACITY OF 20 HL PER BREW YEAR PRODUCTIVITY OF 6,000 TO 7,000 HL, 3 SORTS OF BEER BREWERY IS NOT LOCATED AT A SEISMIC AREA EQUIPMENT DESIGNED ACCORDING TO EUROPEAN STANDARD STEAM HEATED 2-VESSEL BREW HOUSE OF 20 HECTOLITRES IN STAINLESS STEEL SCOPE OF SUPPLY: MALT MILL 1 X 2-ROLL MILL WITH CAPACITY OF 400 TO 800 KG/H WITH INLET FROM THE TOP FOR MALT SACKS BREW HOUSE 20HL STEAM HEATED STAINLESS STEEL 1.1 MASH/WORTH – KETTLE DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 LLC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF STAINLESS STEEL 2 STEAM HEATING ZONES (BOTTOM AND CYLINDRICAL PART) AGITATOR AND SHAFT IN STAINLESS STEEL, MATERIAL 1.4301. INSTALLATION OF BOTTOM CENTER. DRIVE VIA GEAR MOTOR, SPEED CONTROLLABLE BY FREQUENCY CONVERTER 1 SPRAY BALL 1 MAN HOLE WITH GLASS 1 PRESSURE RELIEF VALVE – SAFETY VALVE 1 LEVELMEASUREMENT DESIGNED FOR NON PRESSURE OPERATION 1.2 LAUTER TUN DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF STAINLESS STEEL ISOLATION OF THE CYLINDRICAL PART AND THE BOTTOM - 100 MM HALOGEN-FREE MINERAL WOOL. BOTTOM OF THE LAUTER TUN WITH OUTLET VALVES, BACK WASH VALVES AND A DRAIN VALVE MULTIPART SIEVE PLATE 1.4301 REMOVABLE THROUGH MANHOLE. HOEING 1.4301 TWO-ARMED WITH KNIVES AND TREBERN SWORD. INSTALLATION OF BOTTOM CENTER. 1 LAUTER STATION WITH CIP SPRAY BALL 1 MANHOLE WITH GLASS 1 SPRAY BALL 1 TREBERN FLAP AT THE CYLINDRICAL PART DESIGNED FOR NON PRESSURE OPERATION THE PACKAGE INCLUDES ALL VALVES, CHECK VALVES, BUTTERFLY VALVES, 2 PUMPS AND TEMPERATURE PROBES LANDING AND STAIRS MADE OF STAINLESS STEEL SQUARE ROOF BARS, COVERED WITH CORRUGATED SHEET METAL, HEIGHT ADJUSTABLE FEET WITH DOMES. THE PAN DUST WILL BE COLD DOWN WITH COLD WATER AND THE CONDENSATE WILL BE TRANSFERRED TO THE DRAIN WHIRLPOOL 20HL VESSEL MADE OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220. NON INSULATED. 1 WHIRLPOOL PUMP 2 LATERAL OUTLETS WITH HAND VALVES 1 FLOOR DRAIN WITH HAND VALVE 1 TANGENTIAL INLET PORT WITH THREADED CONNECTOR 1 SAFETY VALVE 1 MANHOLE 1 SPRAY BALL DESIGNED FOR NON PRESSURE OPERATION WORTHCOOLING + WORTH AERATION VESSEL MADE OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220. NON INSULATED. 1 WHIRLPOOL PUMP 2 LATERAL OUTLETS WITH HAND VALVES 1 FLOOR DRAIN WITH HAND VALVE 1 TANGENTIAL INLET PORT WITH THREADED CONNECTOR 1 SAFETY VALVE 1 MANHOLE 1 SPRAY BALL DESIGNED FOR NON PRESSURE OPERATION 1. SECTION: 20 HL WORTH IS COOLED WITH COLD WATER FROM 98°C TO 17°C IN 60 MINUTES (COLD WATER FROM CLIENT SIDE MUST BE MAX. 15°C OR LOWER) 2. SECTION: WITH ICE WATER OR GLYCOL THE WORTH IS COOLED TO 5°C CONTROL SYSTEM EACH PNEUMATIC CONTROLLED VALVE WILL HAVE A SWITCH BUTTON ON A CONTROL PANEL IN THE MIDDLE OF THE BREW HOUSE. ALSO THE TEMPERATURE CONTROL OF THE MASH KEETEL AND WORTH KETTLE WILL BE IMPLEMENTED AT THE CONTROL PANEL WITH A HARD WARE CONTROLLER. HOT WATER TANK 30 HL VERTICAL DESIGN, MATERIAL 1.4301 DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF MATERIAL 1.4301 WITH GRAIN 220 1 HOT WATER PUMP 1 CIRCULATION PUMP 1 PT 100 AN CONTROLLER 1 STEAM VALVE AND CONDENSATE VALVE 1 LEVEL INDICATION 10 X CYLINDER CONICAL TANKS 40/48 HL VERTICAL DESIGN WITH DISHED BOTTOM AND 60° CONE. CONE AND CYLINDRICAL PART IS INSULTED AND THE FULL TANK IS EQUIPPED WITH WELDED STAINLESS STEEL EXTERIOR FINISH. TANK HEIGHT APPROX.: 4.050MM TANK EQUIPPED WITH COOLING JACKET (1 ZONE) AND CONE COOLING (2 ZONE), BY TEMP- PLATE, SUITABLE FOR ICE WATER / GLYCOL. SEPARATE CONNECTIONS FOR COOLING FOR CASING AND CONE : NIPPLE ¾ " EXTERNAL THREAD TANK WITH MANHOLE 500 X 400 MM, WITH MANHOLE COVER AND DUAL HINGE. 2 OUTLET DN 32 INSTALLED IN A DN 125 - THREAD , PULLED FORWARD AND ENDED BUTTERFLY VALVE DN 32 G / S , WITH BLANKING CAP. UPPER FLOOR PROVIDED WITH 2 THREADED CONNECTION DN 32 FOR CONNECTION OF AN RLV - FITTING. ONE OF THE TERMINALS INSTALLED IN A FITTING DN 100 AND DN 25 PROVIDED WITH REMOVABLE SPRAY BALL CLEANING PIPE DN25, TOP PROVIDED WITH CONNECTION CONE / NUT DN 32FOR CONNECTION TO THE RLV COMBINATION, PULLED DOWN AND ENDING ON OPERATING HEIGHT IN THREADED CONNECTION DN 50, INCLUDING BLANKING CAP. IN THE CLEANING DUCT 2 CONNECTOR WITH THREADED CONNECTION DN 20 FOR SPUND APPARATUS AND WITH BALL VALVE FOR THE GAS SUPPORT 1 CONNECTOR FOR SAMPLE VALVE: THREADED CONNECTION DN 20 2 CONNECTION FOR PT -100: IMMERSION SLEEVE 260 MM LONG, WITH SLEEVE ½ " . 2 SOLENOID VALVE FOR THE COOLING DUCT 4 MANUAL VALVES IN THE COOLANT INLET AND COOLANT OUTLET LINE 4 THE HEIGHT ADJUSTABLE TUBE FEET , INCLUDING FOOTPLATE. MATERIAL: 1.4301. FINISH: - INSIDE: - 2B (IIIC-SHEET), DISHED BOTTOM GROUND. - WELDS - ROUND & LONG SEAMS SANDED. - REST STAINED / BRUSHED. - OUTSIDE: - 2B (IIIC-SHEET). - WELDS - ROUND & LONGITUDINAL SEAMS SANDED. - REST STAINED / BRUSHED TANK SUITABLE FOR 3 BAR G. (20 ° C), DECREASE ACCORDING TO PED 97/23/EC. FILTRATION 20 HL/H KISELGUR- FILTER WITH HORIZONTAL SLICES AND CAPACITY OF 20HL / HOUR 3 X PRESSURE DISPENDING TANKS 40/46 HL VERTICAL DESIGN WITH DISHED BOTTOM LOWER + UPPER BOTTOM AND CYLINDRICAL PART IS INSULTED AND THE FULL TANK IS EQUIPPED WITH WELDED STAINLESS STEEL EXTERIOR FINISH. TANK HEIGHT APPROX.: 3.350MM TANK EQUIPPED WITH COOLING JACKET (1 ZONE) BY TEMP- PLATE, SUITABLE FOR ICE WATER / GLYCOL. CONNECTION FOR COOLING: NIPPLE ¾ " EXTERNAL THREAD TANK WITH MANHOLE 500 X 400 MM, WITH MANHOLE COVER AND DUAL HINGE. 1OUTLET DN 32 PULLED FORWARD AND ENDED BUTTERFLY VALVE DN 32 G / S , WITH BLANKING CAP. UPPER FLOOR PROVIDED WITH 2 THREADED CONNECTION DN 32 FOR CONNECTION OF AN RLV - FITTING. ONE OF THE TERMINALS INSTALLED IN A FITTING DN 100 AND DN 25 PROVIDED WITH REMOVABLE SPRAY BALL CLEANING PIPE DN 25, TOP PROVIDED WITH CONNECTION CONE / NUT DN 32 FOR CONNECTION TO THE RLV COMBINATION, PULLED DOWN AND ENDING ON OPERATING HEIGHT IN THREADED CONNECTION DN 32, INCLUDING BLANKING CAP. IN THE CLEANING DUCT 2 CONNECTOR WITH THREADED CONNECTION DN 20 FOR SPUND APPARATUS AND WITH BALL VALVE FOR THE GAS SUPPORT 1 CONNECTOR FOR SAMPLE VALVE: THREADED CONNECTION DN 20 1 CONNECTION FOR PT -100: IMMERSION SLEEVE 260 MM LONG, WITH SLEEVE ½ " . 1 SOLENOID VALVE FOR THE COOLING DUCT 2 MANUAL VALVES IN THE COOLANT INLET AND COOLANT OUTLET LINE 4 THE HEIGHT ADJUSTABLE TUBE FEET , INCLUDING FOOTPLATE. MATERIAL: 1.4301. FINISH: - INSIDE: - 2B (IIIC-SHEET), DISHED BOTTOM GROUND. - WELDS - ROUND & LONG SEAMS SANDED. - REST STAINED / BRUSHED. - OUTSIDE: - 2B (IIIC-SHEET). - WELDS - ROUND & LONGITUDINAL SEAMS SANDED. - REST STAINED / BRUSHED TANK SUITABLE FOR 3 BAR G. (20 ° C), DECREASE ACCORDING TO PED 97/23/EC. COOLING UNIT COOLING UNIT FOR THE OFFERT TANKS AND FOR THE WORTH COOLING. DESIGNED FOR OPERATION WITH GLYCOL COMPRESSOR OIL FREE FULLY AUTOMATIC, OIL-FREE AIR COMPRESSOR STATION WITH STAGE, MOUNTED ON A PRESSURE VESSEL, EQUIPPED WITH PRESSURE SWITCH, OUTLET VALVE, SAFETY VALVE, PRESSURE GAUGE AND MICRO FILTER. STEAM GENERATOR OIL OPERATED OIL OPERATED STEAM GENERATOR WITH A CAPACITY OF 200 KG/H INCLUDING FEED WATER TREATMENT AND FEED WATER CONTROL MOBILE BEER PUMP BEER PUMP WITH FREQUENCY CONVERTER, SINGLE MECHANICAL SEAL, ON STAINLESS STEEL FRAME (WITH CEE PLUG, MOTOR PROTECTION AND 10 M CABLE) FOR PUMPING FROM THE FERMENTATION TANKS TO THE PRESSURIZED TANK 4 PCS. BEER HOSES SET KEG-CLEANER WITH KEG-HANDFILLER CLEANER: CAPACITY: 10 – 15 KEGS / HOUR SEMI AUTOMATICALLY CLEANING PROCESS FOR ALL STANDARD KEGS KEG-HAND FILLER: COMPLETE MADE OF STAINLESS STEEL TUBES 2M LONG FOR ALL STANDARD KEGS PACKAGING WOODEN BOX AND FOILING FOR TRANSPORT IN A CONTAINER (SEA WAY), THE WOODEN BOX ALONE IS NOT ENOUGH FOR THE SEA WAY DOCUMENTATION IN ENGLISH (DEVICE DOCUMENTATION) IN ELECTRONIC FORM MOUNTING MATERIAL FOR MECHANICAL AND ELECTRICAL WORK UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING MOUNTING AND COMMISSIONING FOR MECHANIC WORK AND ELECTRIC WORK (LIFTING DEVICES- CRANE, ENERGY, RAW MATERIAL, CLEANING SOLUTION, HOTEL, FLIGHT TICKET, LABOURER FOR MOUNTING SUPPORT) UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING 4 TEST BREWS (ENERGY, RAW MATERIAL, CLEANING SOLUTION, HOTEL, FLIGHT TICKET) AND TRAINING OF THE OPERATOR STAFF UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING LABORATORY CIVIL WORK CO2 – SUPPLY PERMITS AND LICENSES FROM LOCAL AUTHORITIES TRANSPORT WATER TREATMENT AND COLD WATER TANK (IF REQUIRED) YEAST MANIPULATION (IF REQUIRED) Attached 3 photos from similar equipment. F1: brewhouse F2: CCT (cylindroconicalk tanks) and BBT (bright beer tanks = dispensing tanks) F3: PHE(plate heat exchanger = wort cooling, whirlpool, hot water tank) QUANTITY AVAILABLE: 1 Learn More