Search results for: 'line''

REFERENCE NUMBER: M-5109 (1212CFTNXX11) L GDM ADULT TEXTILE BACK-SHEET WITH BREATHABLE YEAR 2007 ADULT INCONTINENCE ADULT TEXTILE BACK-SHEET WITH BREATHABLE YEAR 2007 BRAND NAME GDM DESIGN SPEED 250 PCS PER MINUTE SIZES: ALL LAST RUN 2013 DRY RUN POSSIBLE SOFT BACK SHEET: IN-LINE OR OFF-LINE APPLICATION QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-3349 (88013DYN7U)-D TOYOTA AIRJET LOOMS TOYOTA AIR JET LOOM QTY MODEL=JA2S-190TP-T610 TOTAL 60 LOOMS 60 STAUBLI POSITIVE TAPPET CAM MOPTION TYPE 1620 CAM BOX WITH 7 SHAFT 6 CAMS WITH 1 SPACER FOR EACH LOOM 60SETS 1 REPEAT GEAR FOR EACH LOOM 60SETS PROFILE REED SYSTEM REED SPACE 190 CM 60 LOWER BUILT ONE PIECE BOX TYPE SIDE FRAME FOR HIGH SPEED OPERATION 60 OIL BATH LUBRICATION FOR MAIN UNITS 60 TWO SIDES CRANK DRIVE BEATING WITH OIL BATH 60 HIGH TORQE INDUCTION MOTOR WITH SOLENOID BRAKE (4P-3PHASE,3.5KW) 60 MAIN CONTROL COMPUTER WITH 32 BYTES CPU 60 DISTRIBUTED CONTROL SYSTEM BY OPTICAL FIBER COMMUNICATION NETWORK 60 TOUCH SCREEN FUNCTION PANEL WITH MULTI- WINDOW DISPLAY 60 AUTOMATIC INITIAL CONDITION - (ICS) SYSTEM 60 AUTOMATIC FAULT ALRAM FUNCTION 60 WEEKLY EFFICIENCY GRAPH DISPLAY & DOWN TIME 60 CAUSE DISLPAY BEAM CLOTH ESTIMATOR 60 2 COLOUR MIXING DEVICE BY ELECTRIC DRUM POLE (EDP) 60 TAPERED SUB NOZZLE 60 LOW AIR PRESURE & HIGH PROPULSIVE MAIN NOZZLE 60 DIRECT DRIVE SOLENOID VALVE FOR MAIN & SUB NOZZLE 60 TWO INDEPENDENT SUB NOZZLE TANKS 60 TAPERED TUNNEL REED 60 AUTOMATIC TIMING CONTROLLER (ATC) 60 AUTOMATIC BRAKE SYSTEM (ABS) 60 TIMING CHEKER WITH GRAPH DISPLAY ON FUNCTION PANEL 60 CENTRALIZED REGULATOR 60 ELECTRONIC LET OFF MOTION BY DIGITAL AC SERVO MOTOR 60 AUTOMATIC LET OFF ADJUSTMENT 60 FELL FORWARD DEVICE FOR STOP MARK PREVENTION 60 POSITIVE EASING MOTION WITH TWIN BACK ROLLER 60 MECHANICAL TAKE UP MOTION BY CHANGE GEAR 60 ON LOOM TAKE UP MOTION FOR MAXIMUM -600MM CLOTH DIA 60 DOUBLE PRESS CLOTH ROLLS 60LOOM METAL SPRAYED SURFACE TAKE UP ROOLER 60 RING TAMPLE-3ROWS -24RING 60SET ROTARY LENO SELVEDGE AT L+R SIDE WITH ELECTRIC STOP MOTION 60SET DOUBLE FEELER FOR WEFT STOP MOTION -(REFLECTING TYPE ) 60 ELECTRIC WARP STOP MOTION BY SIX LINES CONTACT BAR 6 PER LOOM YARN BEAM SET WITH 1000 MM FLANGE & 178 MM BAREL DIA 90 CLOTH ROLLER 100 MM DIA 90 REED 60PIECE HEALD FRAMES 7 PER LOOM HEALD WIRE (331MML) C TYPE 6000PER LOOM DROPPER- (165-11-0.3) 6000PER LOOM QUANTITY: 60 TOYOTA AIR JET LOOM QTY MODEL=JA2S-280TP-T610 TOTAL 12 LOOM. 12 STAUBLI POSITIVE TAPPET CAM MOPTION 12SETS TYPE 1620 CAM BOX WITH 7 SHAFT 6 CAMS WITH 1 SPACER FOR EACH LOOM 12SETS 1 REPEAT GEAR FOR EACH LOOM 12SETS PROFILE REED SYSTEM REED SPACE 280 CM 12 LOWER BUILT ONE PIECE BOX TYPE SIDE FRAME FOR HIGH SPEED OPERATION 12 OIL BATH LUBRICATION FOR MAIN UNIT 12 TWO SIDES CRANK DRIVE BEATING WITH OIL BATH 12 HIGH TORQE INDUCTION MOTOR WITH SOLENOID 12 BRAKE (4P-3PHASE,3.5KW) MAIN CONTROL COMPUTER WITH 32 BYTES CPU 12 DISTRIBUTED CONTROL SYSTEM BY OPTICAL FIBER 12 COMMUNICATION NETWORK TOUCH SCREEN FUNCTION PANEL WITH MULTI- WINDOW DISPLAY 12 AUTOMATIC INITIAL CONDITION - (ICS) SYSTEM AUTOMATIC FAULT ALRAM FUNCTION 12 WEEKLY EFFICIENCY GRAPH DISPLAY & DOWN TIME 12 CAUSE DISLPAY BEAM CLOTH ESTIMATOR 12 2 COLOUR MIXING DEVICE BY ELECTRIC DRUM POLE (EDP) 12 TAPERED SUB NOZZLE 12 LOW AIR PRESURE & HIGH PROPULSIVE MAIN NOZZLE 12 DIRECT DRIVE SOLENIOD VALVE FOR MAIN & SUB NOZZLE 12 TWO INDEPENDENT SUB NOZZLE TANKS 12 TAPERED TUNNEL REED 12 AUTOMATIC TIMING CONTROL (ATC) 12 AUTOMATIC BRAKE SYSTEM (ABS) 12 TIMING CHEKER WITH GRAPH DISPLAY ON FUNCTION PANEL 12 CENTRALIZED REGULATOR 12 ELECTRONIC LET OFF MOTION BY DIGITAL AC SERVO MOTOR 12 AUTOMATIC LET OFF ADJUSTMENT 12 FELL FORWARD DEVICE FOR STOP MARK PREVENTION 12 POSITIVE EASING MOTION WITH TWIN BACK ROLLER 12 MECHANICAL TAKE UP MOTION BY CHANGE GEAR 12 ON LOOM TAKE UP MOTION FOR MAXIMUM -600MMCLOTH DIA 12 DOUBLE PRESS CLOTH ROLLS 12LOOM METAL SPRAYED SURFASE TAKE UP ROOLER 12 RING TAMPLE-3ROW -30RING 12SET OCCUPIED WITH TUCK IN DEVICE WITH COMPLETE ACCESSORIES DOUBLE FEELER FOR WEFT STOP MOTION -(REFLECTING TYPE ) ELECTRIC WARP STOP MOTION BY SIX LINES CONTACT BAR 6PER LOOM YARN BEAM SET WITH 1000 MM FLANGE & 178 MM BARREL DIA 18 CLOTH ROLLER 100 MM DIA 18 REED 12PIECE HEALD FRAMES 7 PER LOOM HEALD WIRE (331MML) C TYPE 8000PER LOOM DROPPER- (165-11-0.3) 8000PER LOOM QUANTITY AVAILABLE: 12 LOOMS 20 LOOMS HAVE GEAR FOR TUCK IN DEVICE, GEAR BOX AT LEFT SIDE 1 INVERTER FOR 36 LOOMS ( 2 INVERTERS FOR ALL 72) 2 ATLAS COPCO ZR-315 COMPRESORS AND DRYER MD-1000 AVAILALE AT ADDITIONAL COST Learn More

REFERENCE NUMBER: A-1119 COMPLETE OPEN END PLANT WITH 1.200 ROTORS YEAR FROM 1990 TO 2005 BLOWROOM CARDS DRAWFRAMES OPEN END QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More

FEATURES: 1. ROBUST AND RELIABLE. 2. SUITABLE FOR A WIDE SPECTRUM OF MATERIALS, INCLUDING LDPE, LLDPE, AND RECYCLED PE. 3. CAN PRODUCE FILMS WITH VARIOUS BUBBLE SIZES FROM DIAMTER 6 TO DIAMETER 32, BY CHANGING THE ROLLER. 4. INDEX REVOLVING WINDER IS EASY TO OPERATE. 5. VARIABLE SPEED DRIVE CAN GREATLY REDUCE ENERGY CONSUMPTION. 6. THIS MODEL CAN ALSO BE USED FOR FILMS WITH TWO LAYER FILM MACHINE. SPECIFICATIONS: MODEL: 25 MAXIMUM WIDTH: 2530mm MAXIMUM OUTPUT: 190 KG/HR LINE SPEED: 1100M/HR TOTAL POWER: 140 KW MACHINE WEIGHT: 8200 KGS MODEL: 16 MAXIMUM WIDTH: 1630mm MAXIMUM OUTPUT: 120 KG/HR LINE SPEED: 1100M/HR TOTAL POWER: 85 KW MACHINE WEIGHT: 6500 KGS Learn More

REFERENCE NUMBER: M-3973 (99016AVEZ8RX)-D HOTMELT POWDER SCATTERING AND LAMINATING MACHINE-2200mm 1.LAMINATING LINE : MAKE : VILLARS (CH) ACTUALLY SANTEX YEAR: 1993 WORKING WIDTH : 2200mm (NOMINAL WIDTH 2M10) VOLTAGE: 3X380(400)V TOTAL POWER : 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION : INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997) : 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS : 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED 2.ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM : MAKE : MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR: 1999 OPERATING VOLTAGE : 3X380V CAPACITY ACCUMULATOR : +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) 3. SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE : MAKE: MENZEL YEAR: 2000 OPERATING VOLTAGE : 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT KNOWN PROBLEM : PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) 4.MISCELLANEOUS : SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS Learn More

REFERENCE NUMBER: M-4747 (1111NBRTHH10) L INDUSTRIAL BREWERY WITH BREWHOUSE 20 HL INDUSTRIAL BREWERY WITH CAPACITY OF 20 HL PER BREW YEAR PRODUCTIVITY OF 6,000 TO 7,000 HL, 3 SORTS OF BEER BREWERY IS NOT LOCATED AT A SEISMIC AREA EQUIPMENT DESIGNED ACCORDING TO EUROPEAN STANDARD STEAM HEATED 2-VESSEL BREW HOUSE OF 20 HECTOLITRES IN STAINLESS STEEL SCOPE OF SUPPLY: MALT MILL 1 X 2-ROLL MILL WITH CAPACITY OF 400 TO 800 KG/H WITH INLET FROM THE TOP FOR MALT SACKS BREW HOUSE 20HL STEAM HEATED STAINLESS STEEL 1.1 MASH/WORTH – KETTLE DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 LLC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF STAINLESS STEEL 2 STEAM HEATING ZONES (BOTTOM AND CYLINDRICAL PART) AGITATOR AND SHAFT IN STAINLESS STEEL, MATERIAL 1.4301. INSTALLATION OF BOTTOM CENTER. DRIVE VIA GEAR MOTOR, SPEED CONTROLLABLE BY FREQUENCY CONVERTER 1 SPRAY BALL 1 MAN HOLE WITH GLASS 1 PRESSURE RELIEF VALVE – SAFETY VALVE 1 LEVELMEASUREMENT DESIGNED FOR NON PRESSURE OPERATION 1.2 LAUTER TUN DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF STAINLESS STEEL ISOLATION OF THE CYLINDRICAL PART AND THE BOTTOM - 100 MM HALOGEN-FREE MINERAL WOOL. BOTTOM OF THE LAUTER TUN WITH OUTLET VALVES, BACK WASH VALVES AND A DRAIN VALVE MULTIPART SIEVE PLATE 1.4301 REMOVABLE THROUGH MANHOLE. HOEING 1.4301 TWO-ARMED WITH KNIVES AND TREBERN SWORD. INSTALLATION OF BOTTOM CENTER. 1 LAUTER STATION WITH CIP SPRAY BALL 1 MANHOLE WITH GLASS 1 SPRAY BALL 1 TREBERN FLAP AT THE CYLINDRICAL PART DESIGNED FOR NON PRESSURE OPERATION THE PACKAGE INCLUDES ALL VALVES, CHECK VALVES, BUTTERFLY VALVES, 2 PUMPS AND TEMPERATURE PROBES LANDING AND STAIRS MADE OF STAINLESS STEEL SQUARE ROOF BARS, COVERED WITH CORRUGATED SHEET METAL, HEIGHT ADJUSTABLE FEET WITH DOMES. THE PAN DUST WILL BE COLD DOWN WITH COLD WATER AND THE CONDENSATE WILL BE TRANSFERRED TO THE DRAIN WHIRLPOOL 20HL VESSEL MADE OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220. NON INSULATED. 1 WHIRLPOOL PUMP 2 LATERAL OUTLETS WITH HAND VALVES 1 FLOOR DRAIN WITH HAND VALVE 1 TANGENTIAL INLET PORT WITH THREADED CONNECTOR 1 SAFETY VALVE 1 MANHOLE 1 SPRAY BALL DESIGNED FOR NON PRESSURE OPERATION WORTHCOOLING + WORTH AERATION VESSEL MADE OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220. NON INSULATED. 1 WHIRLPOOL PUMP 2 LATERAL OUTLETS WITH HAND VALVES 1 FLOOR DRAIN WITH HAND VALVE 1 TANGENTIAL INLET PORT WITH THREADED CONNECTOR 1 SAFETY VALVE 1 MANHOLE 1 SPRAY BALL DESIGNED FOR NON PRESSURE OPERATION 1. SECTION: 20 HL WORTH IS COOLED WITH COLD WATER FROM 98°C TO 17°C IN 60 MINUTES (COLD WATER FROM CLIENT SIDE MUST BE MAX. 15°C OR LOWER) 2. SECTION: WITH ICE WATER OR GLYCOL THE WORTH IS COOLED TO 5°C CONTROL SYSTEM EACH PNEUMATIC CONTROLLED VALVE WILL HAVE A SWITCH BUTTON ON A CONTROL PANEL IN THE MIDDLE OF THE BREW HOUSE. ALSO THE TEMPERATURE CONTROL OF THE MASH KEETEL AND WORTH KETTLE WILL BE IMPLEMENTED AT THE CONTROL PANEL WITH A HARD WARE CONTROLLER. HOT WATER TANK 30 HL VERTICAL DESIGN, MATERIAL 1.4301 DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF MATERIAL 1.4301 WITH GRAIN 220 1 HOT WATER PUMP 1 CIRCULATION PUMP 1 PT 100 AN CONTROLLER 1 STEAM VALVE AND CONDENSATE VALVE 1 LEVEL INDICATION 10 X CYLINDER CONICAL TANKS 40/48 HL VERTICAL DESIGN WITH DISHED BOTTOM AND 60° CONE. CONE AND CYLINDRICAL PART IS INSULTED AND THE FULL TANK IS EQUIPPED WITH WELDED STAINLESS STEEL EXTERIOR FINISH. TANK HEIGHT APPROX.: 4.050MM TANK EQUIPPED WITH COOLING JACKET (1 ZONE) AND CONE COOLING (2 ZONE), BY TEMP- PLATE, SUITABLE FOR ICE WATER / GLYCOL. SEPARATE CONNECTIONS FOR COOLING FOR CASING AND CONE : NIPPLE ¾ " EXTERNAL THREAD TANK WITH MANHOLE 500 X 400 MM, WITH MANHOLE COVER AND DUAL HINGE. 2 OUTLET DN 32 INSTALLED IN A DN 125 - THREAD , PULLED FORWARD AND ENDED BUTTERFLY VALVE DN 32 G / S , WITH BLANKING CAP. UPPER FLOOR PROVIDED WITH 2 THREADED CONNECTION DN 32 FOR CONNECTION OF AN RLV - FITTING. ONE OF THE TERMINALS INSTALLED IN A FITTING DN 100 AND DN 25 PROVIDED WITH REMOVABLE SPRAY BALL CLEANING PIPE DN25, TOP PROVIDED WITH CONNECTION CONE / NUT DN 32FOR CONNECTION TO THE RLV COMBINATION, PULLED DOWN AND ENDING ON OPERATING HEIGHT IN THREADED CONNECTION DN 50, INCLUDING BLANKING CAP. IN THE CLEANING DUCT 2 CONNECTOR WITH THREADED CONNECTION DN 20 FOR SPUND APPARATUS AND WITH BALL VALVE FOR THE GAS SUPPORT 1 CONNECTOR FOR SAMPLE VALVE: THREADED CONNECTION DN 20 2 CONNECTION FOR PT -100: IMMERSION SLEEVE 260 MM LONG, WITH SLEEVE ½ " . 2 SOLENOID VALVE FOR THE COOLING DUCT 4 MANUAL VALVES IN THE COOLANT INLET AND COOLANT OUTLET LINE 4 THE HEIGHT ADJUSTABLE TUBE FEET , INCLUDING FOOTPLATE. MATERIAL: 1.4301. FINISH: - INSIDE: - 2B (IIIC-SHEET), DISHED BOTTOM GROUND. - WELDS - ROUND & LONG SEAMS SANDED. - REST STAINED / BRUSHED. - OUTSIDE: - 2B (IIIC-SHEET). - WELDS - ROUND & LONGITUDINAL SEAMS SANDED. - REST STAINED / BRUSHED TANK SUITABLE FOR 3 BAR G. (20 ° C), DECREASE ACCORDING TO PED 97/23/EC. FILTRATION 20 HL/H KISELGUR- FILTER WITH HORIZONTAL SLICES AND CAPACITY OF 20HL / HOUR 3 X PRESSURE DISPENDING TANKS 40/46 HL VERTICAL DESIGN WITH DISHED BOTTOM LOWER + UPPER BOTTOM AND CYLINDRICAL PART IS INSULTED AND THE FULL TANK IS EQUIPPED WITH WELDED STAINLESS STEEL EXTERIOR FINISH. TANK HEIGHT APPROX.: 3.350MM TANK EQUIPPED WITH COOLING JACKET (1 ZONE) BY TEMP- PLATE, SUITABLE FOR ICE WATER / GLYCOL. CONNECTION FOR COOLING: NIPPLE ¾ " EXTERNAL THREAD TANK WITH MANHOLE 500 X 400 MM, WITH MANHOLE COVER AND DUAL HINGE. 1OUTLET DN 32 PULLED FORWARD AND ENDED BUTTERFLY VALVE DN 32 G / S , WITH BLANKING CAP. UPPER FLOOR PROVIDED WITH 2 THREADED CONNECTION DN 32 FOR CONNECTION OF AN RLV - FITTING. ONE OF THE TERMINALS INSTALLED IN A FITTING DN 100 AND DN 25 PROVIDED WITH REMOVABLE SPRAY BALL CLEANING PIPE DN 25, TOP PROVIDED WITH CONNECTION CONE / NUT DN 32 FOR CONNECTION TO THE RLV COMBINATION, PULLED DOWN AND ENDING ON OPERATING HEIGHT IN THREADED CONNECTION DN 32, INCLUDING BLANKING CAP. IN THE CLEANING DUCT 2 CONNECTOR WITH THREADED CONNECTION DN 20 FOR SPUND APPARATUS AND WITH BALL VALVE FOR THE GAS SUPPORT 1 CONNECTOR FOR SAMPLE VALVE: THREADED CONNECTION DN 20 1 CONNECTION FOR PT -100: IMMERSION SLEEVE 260 MM LONG, WITH SLEEVE ½ " . 1 SOLENOID VALVE FOR THE COOLING DUCT 2 MANUAL VALVES IN THE COOLANT INLET AND COOLANT OUTLET LINE 4 THE HEIGHT ADJUSTABLE TUBE FEET , INCLUDING FOOTPLATE. MATERIAL: 1.4301. FINISH: - INSIDE: - 2B (IIIC-SHEET), DISHED BOTTOM GROUND. - WELDS - ROUND & LONG SEAMS SANDED. - REST STAINED / BRUSHED. - OUTSIDE: - 2B (IIIC-SHEET). - WELDS - ROUND & LONGITUDINAL SEAMS SANDED. - REST STAINED / BRUSHED TANK SUITABLE FOR 3 BAR G. (20 ° C), DECREASE ACCORDING TO PED 97/23/EC. COOLING UNIT COOLING UNIT FOR THE OFFERT TANKS AND FOR THE WORTH COOLING. DESIGNED FOR OPERATION WITH GLYCOL COMPRESSOR OIL FREE FULLY AUTOMATIC, OIL-FREE AIR COMPRESSOR STATION WITH STAGE, MOUNTED ON A PRESSURE VESSEL, EQUIPPED WITH PRESSURE SWITCH, OUTLET VALVE, SAFETY VALVE, PRESSURE GAUGE AND MICRO FILTER. STEAM GENERATOR OIL OPERATED OIL OPERATED STEAM GENERATOR WITH A CAPACITY OF 200 KG/H INCLUDING FEED WATER TREATMENT AND FEED WATER CONTROL MOBILE BEER PUMP BEER PUMP WITH FREQUENCY CONVERTER, SINGLE MECHANICAL SEAL, ON STAINLESS STEEL FRAME (WITH CEE PLUG, MOTOR PROTECTION AND 10 M CABLE) FOR PUMPING FROM THE FERMENTATION TANKS TO THE PRESSURIZED TANK 4 PCS. BEER HOSES SET KEG-CLEANER WITH KEG-HANDFILLER CLEANER: CAPACITY: 10 – 15 KEGS / HOUR SEMI AUTOMATICALLY CLEANING PROCESS FOR ALL STANDARD KEGS KEG-HAND FILLER: COMPLETE MADE OF STAINLESS STEEL TUBES 2M LONG FOR ALL STANDARD KEGS PACKAGING WOODEN BOX AND FOILING FOR TRANSPORT IN A CONTAINER (SEA WAY), THE WOODEN BOX ALONE IS NOT ENOUGH FOR THE SEA WAY DOCUMENTATION IN ENGLISH (DEVICE DOCUMENTATION) IN ELECTRONIC FORM MOUNTING MATERIAL FOR MECHANICAL AND ELECTRICAL WORK UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING MOUNTING AND COMMISSIONING FOR MECHANIC WORK AND ELECTRIC WORK (LIFTING DEVICES- CRANE, ENERGY, RAW MATERIAL, CLEANING SOLUTION, HOTEL, FLIGHT TICKET, LABOURER FOR MOUNTING SUPPORT) UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING 4 TEST BREWS (ENERGY, RAW MATERIAL, CLEANING SOLUTION, HOTEL, FLIGHT TICKET) AND TRAINING OF THE OPERATOR STAFF UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING LABORATORY CIVIL WORK CO2 – SUPPLY PERMITS AND LICENSES FROM LOCAL AUTHORITIES TRANSPORT WATER TREATMENT AND COLD WATER TANK (IF REQUIRED) YEAST MANIPULATION (IF REQUIRED) Attached 3 photos from similar equipment. F1: brewhouse F2: CCT (cylindroconicalk tanks) and BBT (bright beer tanks = dispensing tanks) F3: PHE(plate heat exchanger = wort cooling, whirlpool, hot water tank) QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: J-0015 (11116JKYCV10) PLANTEX BCF MULTIFILAMENT PP CARPET YARN MACHINERY YEAR 1998 BRAND: PLANTEX TYPE: 3/12U/3C X 2 YEAR: 1998 FOR POLYAMIDE AND POLYPROPYLENE 1000-6000 DTEX YARNIN 3 COLORS ALTERNATIVE 2 OR 1 COLOR SOLUTION DYED PRODUCTION 6 X150 –750kg/H WITH 24 THREAD LINES FOR 1000-3000 DENIER 12 THREAD LINES FOR 3000-6000 DENIER FILAMENT RANGE 15 TO 25 DEN/FILAMENT PLANT FEATURES 6 ELECTRONIC GRAVIMETRIC DOZING 4 COMPOUND 6 EXTRUDERS 2 SPINNHEAD 6 SPINNING PUMPS 6 SPINNING POSITIOS 24 SPINNING PACKS 72 SPINNERETTES GODETS PRE-TENSION GODETS 1 MOTORISED ROLL WITH 1 IDLE ROLL PER SPINNING POSITION SLOW DRAWING GODETS 1 MOTORISED HEATED ROLL WITH 1 IDLE ROLL PER SPINN. POS. FAST DRAWING GODETS 2 MOTORISED HEATED ROLLS PER SPINNING POSITION TAKE-UP FEEDING GODETS 1 MOTORISED ROLL WITH 1 IDLE ROLL PER WINDER (2 ENDS) MAXIMUM-SPEED 3.000 M/MIN TEXTURISING SYSTEM TEXTURISING POSITIONS 6 TEXTURISERS 24 (4 EACH TEXTURISING POSITION) COOLING DRUMS (4 ENDS EACH) INTERLACERS 12 (2 ENDS EACH) WINDERS 12 MAXIMUM SPEED 3.000 M/MIN BOBBINS 2 PER WINDER WINDING TUBE I.D. 73 MM WINDING TUBE O.D. 79 MM WINDING TUBE LENGTH 290 MM WINDING TRAVERSE STROKE 250 MM BOBBIN MAX. DIAMETER 360 MM BOBBIN MAX. WEIGHT 4,5 K QUANTITY AVAILABLE: 2 Learn More

MACHINE FEATURES: - WITH NC SERVICE ROLLER, AUTOMATIC ADDING OIL DEVICE, BACKING YARN STORAGE DEVICE, DEVICE YARN NEEDLE, YARN COLLECTING PLAT AND AUTO STOP DEVICE. -THE MAIN MOTOR IS CONTROLLED BY INVERTER AND PLC. -THE CREEL IS CONTROLLED BY PNEUMATIC, AND ITS POSITION IS ACCURACY CONTROLLED BY PHOTOELECTRIC SENSOR AND THE PLC AUTOMATICALLY. -THE MAIN BRAKE ADEPTS PNEUMATIC BUTTERFLY BRAKE. THE BREAKING TRAY WITH MIDDLE UNOCCUPIED HAS A NICE HEAT-DISSIPATED FUNCTION. ON THE OTHER HAND, THE USING OF BREAK PINCER WITH AUTO-COMPENSATION AND THE HOOFED PIECE MAKES THE BUTTERFLY BRAKE STABLE AND LAST A LONG LIFE. -THE BRAKE OF POSITIVE ROLLER AND SPEED ROLLER CAN MAKE DIFFERENT BRAKE PRESSURES ACCORDING TO DIFFERENT SPEEDS (MORE THAN 200 M/MIN). THESE DIFFERENT PRESSURES, TOGETHER WITH THE MAIN BEAM BREAK, GUARANTEES THE YARN TENSION IN THE BREAKING TIME IS THE SAME AS THE TENSION UNDER THE CONSTANT SPEED. -WITH TOUCH SCREEN. ALL THE ELECTRICAL TROUBLES AND WRONG OPERATION INFORMATION ARE DISPLAYED ON THE SCREEN. THE PNEUMATIC PART, AORTIC, IS MADE IN TAIWAN. -THE POSITIVE ROLLER IS COVERED BY HIGH-HARDNESS COATING, SO THE SMOOTH SURFACE IMPROVES THE ABSORPTION TO THE YARN. THE AC HIGH-SPEED SERVO SYSTEM PROVIDES A POWER TO THE ABOVE ROLLER, MATCHING WITH THE PLC, BOTH OF WHICH SERVICE FOR THE MAIN WINDING SYSTEM, TO ENSURE THE CONSTANT TENSION OF YARN. -WITH REMOTE DEBUGGING TO MONITOR THE CURRENT WORKING CONDITIONS. CONSISTS OF: (1) COMPUTER CONTROLLED COPY WARPING MACHINE FOR 30”X42” INCH AND 21”X42” BEAM (2) ROTATION OPEN CREEL WITH 1400 POSITIONS AND KFD OIL HYDRAULIC TENSIONER (1) COMPUTER CONTROLLED COPY WARPING MACHINE FOR 30”X42” INCH AND 21”X42” BEAM TECHNICAL DATA: LINE SPEED 0 TO 1000M/MIN MAX. TENSION OF LINE 1000N BRAKE TORQUE 3200NM UP AND DOWN OF BEAM PNEUMATIC CONTROL TIGHT AND RELEASE OF BEAM PNEUMATIC CONTROL DIAMETER OF SPEED ROLLER Ø120mm POWER OF MAIN MOTOR 15KW CONTROL TYPE OF MAIN MOTOR INVERTER CONTROL MONITORING WAY IMMEDIATE MONITOR BY MICROCOMPUTER CONTROLLED TOUCH SCREEN CONTROL TYPE OF POSITIVE YARN-SEND ROLLER AC HIGH-SPEED SERVO CONTROL SYSTEM OF MITSUBISHI DIAMETER OF POSITIVE YARN-SEND ROLLER Ø100mm PRESSURE OF PNEUMATIC SOURCE 6 BAR MAIN PARTS： MAIN MOTOR SIEMENS OF GERMANGY HIGH-SPEED SERVO SYSTEM MITSUBISHI OF JAPAN CONVERTER EMERSON OF USA TEST COMPONENTS A AUTONICS OF SOUTH KOREA TEST COMPONENTS B KOYO OF JAPAN PNEUMATIC COMPONENTS AIRTAC OF TAIWAN PLC OMRON OF JAPAN TOUCH SCREEN MCGS OF BEIJING OPERATING COMPONENTS SCHNEIDER OF FRANCE TERMINAL COMPONENTS PHOENIXCONTACT OF GERMANGY BEARING NSK OF JAPAN (2) ROTATION OPEN CREEL WITH 1400 POSITIONS AND KFD OIL HYDRAULIC TENSIONER MAJOR PARTS: 1. MOTOR 2. ROLLER SPEED DETECTOR 3. CONTROL PANEL 4. REED 5. SIZING PARTS 6. LUBRICATING DEVICE 7. YARN STORAGE 8. TENSION ROLLER 9. STATIC ELIMINATOR 10. NEEDLES 11. YARN COLLECTING BOARD DELIVERY TIME: 37-45 DAYS Learn More

YY-3584 CBD/HEMP OIL EXTRACTION INTRODUCTION THE CONTENT OF CBD OIL IN ALL PARTS OF HEMP ,USUALLY DECREASES ACCORDING TO THE ORDER OF BRACTS, FLOWERS, LEAVES, FINE STEMS AND THICK STEMS, AND THE CONTENT OF CBD IN THE FLOWERS AND LEAVES OF FEMALE FLOWERS IS THE HIGHEST, SO THE FLOWERS AND LEAVES ARE USUALLY SELECTED TO EXTRACT CBD OIL. OUR DEVELOPED HEMP OIL EXTRACTOR MACHINE (CENTRIFUGE MACHINE) IS ADAPT THE NEW TECHNOLOGY CAN TO MAKE THE EXTRACTOR TIME SHORT AND EFFICIENT EXTRACTION .THE EXTRACTOR MACHINE (CENTRIFUGE MACHINE) HAVE THE JACKET WHICH CAN KEEP THE INSIDE ETHANOL SOLUTION WITH HEMP RAW MATERIAL IN LOW TEMPERATURE. QUANTITY: 1 Learn More