Search results for: 'Electrical c'

TT-1650 SOLAR TURBINE T60 MOBILE UNIT, 60Hz, YEAR 2018, 4.8 MW SOLAR TURBINE T60 MOBILE UNIT 60Hz YEAR 2018 TYPE: STANDARD BRAND: SOLAR CATEGORY: ENGINES/GENERATORS/MOTORS/TRANSMISSIONS SUBCATEGORY: TURBINE IN STOCK: YES CONDITION: EXCELLENT QUANTITY: 2 Learn More

T-7951PRE AND FINISH – NEEDLER, WIDTH 2800mm TO 2900mm ITEM 001 PRE - NEEDLER QUANTITY: 1 ITEM 002 FINISH - NEEDLER QUANTITY: 1 Learn More

T-7941 CALENDERING MACHINE - IRONING MACHINE, WORKING WIDTH 2750mm, YEAR 2018 PHYSICAL CONDITION: NEW MACHINE, PERFECT WORKING CONDITION QUANTITY: 1 Learn More

REFERENCE NUMBER: M-7912

MACHINERY TO FORM FILL AND SEAL POUCHES WITH A CORNER SPOUT (NEW)

 

MACHINERY TO FORM FILL AND SEAL POUCHES WITH A CORNER SPOUT (NEW)

FAST MACHINERY, QUICK CHANGEOVERS – DUAL FILM REEL WITH AUTO FILM SPLICE

STAINLESS STEEL CONSTRUCTION IS STANDARD

Learn More

REFERENCE NUMBER: R-9392

ROLLS-ROYCE/ABB DIESEL GENERATORS – NEW, 27.7 MW, FUEL MDO (MARINE DIESEL OIL), YEAR 2015 – 60Hz

 

(5587 KW X 2 + 4190 KW X 4 = 27.934 KW ROLLS-ROYCE)

Learn More

P-5042 JOPER CAST IRON SMALL BATCH ROASTER 5 KILOS

JOPER
CAST IRON SMALL BATCH ROASTER
5 KILOS
JOPER 5 KILOS AUTOMATIC PROFILING CONTROLS. SHIPS WITH YOUR ELECTRICAL AND GAS SPECIFICATIONS. FEATURES THE SAME CAST IRON ATTRIBUTES OF THE OLD PROBAT SCHOOL. THE DRUM ROASTING MACHINE RUNS QUIETLY DUE TO THE HIGH FIBER INSULATION AND NO PULLEYS OR CHAINS IN ITS DESIGN. CHAFF REMOVAL IS QUICK AND EFFICIENT DUE TO THE FREE STANDING DESING. THE POWERFUL SELF CLEANING ROASTING AND COOLING FANS ALLOWS THE SEPARATE AIRFLOW. TWO MODELS: MANUAL AND PROFILE (AUTOMATIC)

DATA:
LOAD CAPACITY 11/POUUNDS BATCH 44 POUNDS PER HOUR
ROASTING TIME 15 MINUTES COOLING 3 MINUTES
NATURAL GAS OR PROPANE
ELECTRICAL REQUIREMENTS CAN NE BEUILT TO YOUR SPECIFICATIONS.
220v 3 PHASE IS THE MOST QUIET, BUT THE ELECTRICAL CAN BE BUILT TO YOUR NEEDED VOLTAGE AND PHASE.
LOW NOX PRECISE BURNER ADJUSTMENT
WEIGHT WITH COOLOR AND CHAFF 992 POUNDS
DIRECT DRIVE SEPARATE MOTORS (4 OF THEM)
REQUIRED FLOOR SPACE: 56 INCHES WIDE 84 INCHES FRONT TO BACK, 79 INCHES HIGH
(DIMS INCLUDE EXTERNAL CHAFF COLLECTOR)
BURNER POWER: 95,000 BTU
BUILT TO UL295 STANDARDS

QUANTITY: 1

Learn More

H-1305 BATT FEEDING SYSTEM - WORKING WIDTH 3000mm

WORKING WIDTH: 3000mm
CONTROL SYSTEM INCLUDED

COMPOSITION OF THE MACHINE:
- LOWER PVC INCLINED CONVEYOR BELT FOR THE TRANSPORT OF THE WEB FROM THE CROSS LAPPER TO THE ENTRANCE OF THE NEEDLE LOOM.
- UPPER PVC COMPRESSION BELT FOR THE PRE-COMPRESSION OF THE WEB BEFORE ENTERING THE FEEDING ROLLS.
- LOWER PVC CONVEYOR AND UPPER PVC BELT DRIVEN BY ONE GEARBOX MOTOR WITH INDEPENDENT FREQUENCY INVERTER.
- PAIR OF FEEDING ROLLS WITH PLASTIC FINGERS TO GUIDE THE COMPRESSED WEB CLOSE TO FIRST NEEDLE ZONE OF THE PRE-NEEDLE LOOM. ROLLER PAIR DRIVEN BY GEARBOX MOTOR WITH INDEPENDENT FREQUENCY INVERTER.
- BATT FEEDING SYSTEM INSTALLED ON RAIL SYSTEM AND EASY REMOVABLE FOR MAINTENANCE OF THE NEEDLE LOOM

TECHNICAL DATA:
ELECTRICAL INFORMATION:
ELECTRIC: MAIN VOLTAGE 400 V, 50 HZ, 3 PH.
CONTROL VOLTAGE: DC - 24 V / AC - 230 V
OTHER INFORMATION:
AIR PRESSURE (CONSTANT): MIN. 6 BAR (AT SITE)
OPERATOR SIDE LEFT OR RIGHT (IN WEB RUNNING DIRECTION)
LACQUER COATING:
MAIN COLOR OF THE MACHINES: RAL 7035 (LIGHT GREY)
CONTROL CABINET AND CONTROL DESK RAL 7035 (LIGHT GREY)
LABELING: ENGLISH
TECHNICAL DOCUMENTATION: ONE TIME ON CD-ROM (FURTHER SETS AVAILABLE AT ADDITIONAL COST)
LANGUAGE FOR OPERATING INSTRUCTIONS: ENGLISH
LANGUAGE FOR FURTHER DOCUMENTATION (SPARE PART LISTS, WIRING DIAGRAM, ETC): ENGLISH

ENVIRONMENTAL CONDITIONS:
INSTALLATION HEIGHT ABOVE SEA LEVEL: LESS THAN OR EQUAL TO 1,000 METERS
TEMPERATURE: 24° C (±2° C)
RELATIVE HUMIDITY: 65% (±5%)
ABSOLUTE WATER CONTENT: 9 TO 12 G/KG DRY AIR
NOTE: PLEASE MAKE SURE THAT THE TEMPERATURE INSIDE THE CONTROL CABINET DOES NOT EXCEED 450 CENTIGRADE. IN CASE OF EXCESSIVE ROOM TEMPERATURES WE RECOMMEND AN AIR-CONDITIONING SYSTEM FOR THE CONTROL CABINETS TO AVOID MALFUNCTION OF ELECTRICAL COMPONENTS

QUANTITY: 1

Learn More

REFERENCE NUMBER:   G-8230

HIGH-TEMPERETURE AND HIGH-PRESSURE YARN DYEING MACHINE 40KG

 

DESIGNED FOR DYEING, BOILING OFF, BLEACHING, AND WATER WASHING, ETC. SUITABLE FOR HANK YARN, BOBBIN OR RAW STOCK FIBER

 

MACHINE TYPE: VERTICAL CYLINDER

VAT DIAMETER: Ф600mm

CONE QUANTITY: 7 X 7 = 49 CONES

WORKING TEMPERATURE: 130C

MAX WORKING PRESSURE: 0.4MPA

BOTH RATIO: 1:7 TO 9

WITH COMPUTERIZED CONTROL SYSTEM

HEAT EXCHANGING: COIL TYPE HEAT EXCHANGER, WHICH CAN BE USED FOR EITHER HEATING OR COOLING.

HEAT EXCHANGING SPEED: WHEN THE HEATED STEAM PRESSURE IS 0.4MPA, 40MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BARREL RAISING FROM 20^OC TO 130^OC. WHEN THE COOLING WATER PRESSURE IS 0. 3MPA AND THE WATER TEMPERATURE IS 20 ^OC, 40 MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BECK TO LOWER FROM 130^OC TO 80^OC.

RECYCLING OF DYEING LIQUID: THE POSITIVE AND NEGATIVE RECYCLING OF DYEING LIQUID WILL BE ADJUSTED BY THE CYLINDER THROUGH THE SWITCHING DEVICE INSIDE THE CENTRIFUGAL PUMP.

SEALING OF BOILER: RUBBER ADHESIVE

THE WORKING PRESSURE INSIDE THE TANK WILL MAKE THE RUBBER SEAL CLOSELY TO ATTACH THE FLANGE. THE CONICAL SURFACE OF THE TANK MOUTH IS TO ENHANCE THE SEALING.

OPENING OF TANK COVER: FIRST OPEN THE AIR VALVE TO RELEASE THE PRESSURE INSIDE THE BOILER. WAIT UNTIL NO EXHAUSTED AIR GOING THRU THE EXHAUST VALVE AND THE READING OF PRESSURE GAUGE IS ZERO, WITHDRAW THE WRENCH HANDLE, OPEN THE CLAMPING HOOP TO REMOVE THE FLANGE; AND THEN OPEN THE COVER WITH DRAG WEIGHT. THE COVER WILL BE CLOSED.

 

CONFIGURATION:

1. ELECTRICAL CABINET: STAINLESS STEEL CABINET, PLASTIC COATING

2. ELECTRICAL COMPONENTS: SIEMENS, OMRON

3. COMPUTER: HG COMPUTER (MADE IN CHINA)

4. ELECTROMAGNETIC VALVE: TAIWAN YADEKE

5. PUMP: CENTRIFUGAL PUMP

6. MOTOR: WANNAN MOTOR

7. TEMPERATURE CONTROL: COMPUTER CONTROL, WITH HEATING, COOLING, KEEPING WARM, ETC. FUNCTION.

8. HEAT EXCHANGER: INTERNAL COIL HEATING

9. VALVE: STAINLESS ANGLE VALVES, PNEUMATIC BUTTERFLY VALVES

10. ONE CARRIER BASKET

11. MACHINE BODY MATERIAL: STAINLESS STEEL, 316 LITERS

12. ACCESSORIES: SEAL RING FOR DYE VAT, SEAL FOR MAIN PUMP, SEAL FOR REVERSING SHAFT

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: G-4425 CHICKEN SLAUGHTER LINE 1500 PER HOUR QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: E-9901 AUTOMATIC COMPUTERIZED PILLOW FILLING LINE FILLING HEAD IS CONTROLLED BY A PLC MODEL: CF FLOORSPACE REQUIRED: 9000 X 5000 X 2100mm (29.5 FEET X 16.4 FEET X 82 INCHES) QUANTITY AVAILABLE: 1 Learn More