Search results for: 'Reference mark'

P-5079 COMMERCIAL JOPER CAST IRON CRM-30 ROASTER 30 KILOS

WHAT WE HAVE HERE IS A VERY RUGGED CAST IRON ROASTING FRAME AND ROASTING CONTACT CLEARANCES WITH THE MACHINE - JUST PLAIN SOLID AND DOES NOT MOVE UNDER LONG OR EXTENDED USE. DOUBLE WALL DRUM MEANS THAT THE HEAT IS ALL DESIGNED TO GO THROUGH THE CENTER OF THE ROASTING CHAMBER, NOT "ONTO" THE DRUM EXTERIOR. TOTAL TRUE CONVECTION. NOT ONLY IS THIS THE SAME STYLE FROM THE OLD GOTHOT & BARTH ROASTER DAYS. . . BUT EVEN BETTER AS THE SHAFT DESIGN SO THAT BEARINGS ARE EXTERNALLY MOUNTED AND ADDITIONALLY ARE AIR COOLED FOR LONG LIFE AND TROUBLE-FREE CONTROL. EVEN THE SIDE PANELS OR PRODUCT FLIGHTS HAVE A LONGER CURVE POSITIONING MORE PRODUCT FLOW INTO THE HOT AIR STREAM, RESULTING IN A SLIGHTLY MORE RAPID ROAST WITH MORE EVEN BEAN INTERIOR AND EXPANSION THAT FRANKLY LEADS THE INDUSTRY.

ALL THIS COMMENTARY ABOVE MEANS THIS ROASTER SIMPLY IS MORE QUIET THAN ANYTHING ON THE MARKET. PERIOD. THERMAL INSULATION WITH HIGHEST QUALITY OF FIBER FOR LOW GAS CONSUMPTION; DIGITAL TEMPERATURE CONTROL. CYCLONE IS SEPARATE. THE COOLER, BEING TOTALLY SEPARATE ALSO HAS THE LARGEST AIR COLLECTION AREA OF ANY ROASTER MADE ALLOWING FOR TOTAL AMBIENT COOL COFFEE IN LESS THAN THREE MINUTES. ADD TO THIS PACKAGE A LOADER OR YOUR CHOICE OF DESTONERS AND EVEN YOUR CHOICE OF CONTROL METHODS.

DATA INFORMATION:
BATCH CAPACITY: 30 KG / 66 LBS
CONTROL DESIGN: MANUAL
CAPACITY PER HOUR: 120 KG / 265 LBS
ROASTING TIME: 12-18 MIN (4 BATCHES AN HOUR)
EXHAUST AIR TREATMENT: OPTIONAL
COOLING CYCLONE: OPTIONAL
PRE-COOLING WITH WATER IN DRUM: OPTIONAL
COOLING TIME: 3-4 MIN
TYPE OF COOLING: AIR AMBIENT
SAFETY DEVICE: YES
BURNER POWER: 110 KW / 375000 BTU
BURNERS MANUFACTURER: RIELLO
OPERATION TYPE BURNER: BS2D-2 STAGE
FUEL TYPE: PROPANE/NAUTRAL GAS/DIESEL
SIDE OF OPERATION: LEFT
POWER REQUIREMENTS: 20 AMP
VOLTAGE/FREQUENCY/PHASES: 400+N-230 V / 50-60 HZ / 3 PH
9 AMP. . . 3 PHASE 50/60 HZ PREFERRED, YOUR CHOICE OF 220/440 - SINGLE PHASE AVAILABLE AT SPECIAL REQUEST
(NOTE ON 3 PHASE. . . NOT ONLY IS IT LESS EXPENSIVE TO OPERATE, BUT IT RUNS MORE QUIETLY THAN SINGLE PHASE WHENEVER OR WHEREVER IT IS USED. KEEP THIS IN MIND FOR ANY MACHINERY.)
Ø EXHAUST CHIMNEY (ROASTER CYCLONE): 250MM / 9,8 INCH
Ø EXHAUST CHIMNEY (COOLER): 250MM / 9,8 INCH
Ø HOPPER ROAST CHIMNEY: 150MM / 5,9 INCH
ROASTER WEIGHT WITH CYCLONE: 1050 KG / 2310 LBS
COOLER WEIGHT: 300 KG / 660 LBS
ROASTER FAN MOTOR: 1, 5 HP
COOLER FAN: 4 HP
DRUM GEARBOX: 1 HP
COOLER GEARBOX: 0, 75 HP
BUILT TO UL295 STANDARDS.

QUANTITY: 1

Learn More

P-5072 STA IMPIANTI ROASTER 15 KILOS

ROASTING MACHINES LINE PARTICULARLY SUITABLE FOR ARTISANAL SPECIALIZED ACTIVITIES IN MEDIUM BATCHES OF HIGH-QUALITY ROASTED COFFEE, SUCH AS ARTISAN MARKET OR COFFEE SHOPS. TECHNOLOGICALLY ADVANCED, CONFIRMS THEMELVES AS IDEAL TOOL FOR ROASTING COMPANIES SPECIALIZED IN SELECTED COFFEES OF HIGHER QUALITY. MADE WITH THE SAME REQUIREMENTS FOR RELIABILITY AND SECURITY FEATURES OF THE BIGGER AND MORE SOPHISTICATED INDUSTRIAL ROASTING MACHINES, ARE AVAILABLE WITH HEATING GENERATOR TYPE GAS OR DIESEL-FUEL BURNER AT MULTIPLE LEVELS OF FLAME AND MANUAL OR AUTOMATIC CONTROL SYSTEM.

TECHNICAL DATA:
ROASTER CAPACITY: 15 KG. | MAX. 19 KG./ CYCLE
ROASTING CYCLE: 9 MINUTES ÷ 20
RAW COFFEE PROCESSING PER HOUR: 60 KG. ÷ 90
INSTALLED ELECTRIC POWER: 1,8 KW | 380 VOLT THREEPHASE + NEUTRAL 50 HZ
THERMAL POWER: 24,000 KCAL/H/ 29 KW.
(NATURAL GAS OR LPG)

MAIN COMPONENTS:
HOPPER OF CHARGE IN STAINLESS STEEL
ROASTING DRUM
HEATING GENERATOR OF NEW GENERATION PATENTED AND COMPLETE OF BURNER
RAMP VALVES FOR GAS SAFETY AND ELECTRIC DEVICE TO CHECK FLAMES RATIFIED AND COMPLETE OF ALARM SIGNAL.
COOLING TANK IN STAINLESS STEEL WITH DOOR FOR CLEANING OPERATIONS
SAFETY PREVENTION SYSTEM ON THE COOLING TANK
SUPPORTING FRAME FOR THE OVER INDICATED COMPONENTS
ELECTRIC CONTROL BOARD TO CHECK AND CONTROL THE MACHINE ACCORDING CE RULES, COMPLETE OF PLC + TOUCH SCREEN FOR MACHINE MANAGEMENT AND TEMPERATURES SIGHT.
INDEPENDENT FANS FOR THE ROASTING DRUM AND THE COOLING TANK
INDEPENDENT MOTORS FOR THE ROASTING DRUM AND THE COOLING TANK
CYCLONE FOR CHAFFS COLLECTING

DETAILS OF COMPONENTS:
HOPPER OF CHARGE IN STAINLESS STEEL WITH MANUAL IN-LET OF COFFEE AND DOOR UNLOADING SYSTEM
ROASTING DRUM: MADE BY A FIXED ELEMENT WITH DOUBLE WALLS INSULATED FOR THERMAL PROTECTION AND SUPPORT OF THE ROTATING CYLINDER MOVING THE PRODUCT. SUCH CYLINDER, COMPLETELY MADE IN COMPOUND STEEL TO OVERCOME THE THERMAL CHANGES, IS DEVELOPED WITH A PERFORATED PLATE FOR THE CONTAINMENT AND SPECIAL BLENDERS ON THE RIGHT AND LEFT SIDE PLACED ON DIFFERENT LEVELS TO GET A PERFECT BLENDING OF COFFEE. AT THE END OF THE ROASTING CYCLE, A WIDE DOOR WITH MANUAL OPENING/CLOSING SYSTEM ALLOWS THE PRODUCT UNLOADING.
HEATING GAS GENERATOR OF NEW CONCEPT, PATENTED, COMPLETE OF BURNER, RAMP VALVES FOR GAS SAFETY AND ELECTRONIC EQUIPMENTS FOR FLAME CONTROL RATIFIED AND COMPLETE OF SIGNALLING ALARM (N°2 FLAME LEVELS)
COOLING TANK IN STAINLESS STEEL: WIDE SURFACE PERFORATED WITH 3 ARMS AND CROSSED FLOWS. UNLOADING MOUTH WITH HAND DRIVE.
SUPPORTING FRAME: MONO-BLOCK, PLATE PRESS-BENDED, STEEL MADE, SUPPORTING THE ELEMENTS PREVIOUSLY DESCRIBED.
SAFETY PROTECTION FOR COOLING TANK
ELECTRIC CONTROL BOARD FOR MACHINE MANAGEMENT ACCORDING CE RULES INTEGRATED.
COMPLETE OF PLC + TOUCH SCREEN FOR MACHINE MANAGEMENT AND TEMPERATURES VISUALIZATION.
POSSIBLE RECORDING OF ROASTING PARAMETERS.
CYCLONE FOR CHAFFS COLLECTING
INDEPENDENT MOTORIZATION FOR ROASTING DRUM AND COOLING TANK
INDEPENDENT ELECTRIC-FAN FOR ROASTING DRUM AND ELECTRIC FAN FOR COOLING TANK.

QUANTITY: 1

Learn More

P-5039 COMPLETE PLANT WITH DYEING – FINISHING – WEAVING - SEWING

PLAIN DYEING AND FINISHING EQUIPMENT:
7 DYEING MACHINES
9 AUTOMATIC DOSING SYSTEM
10 DYEING MACHINE – JIGGER
11 DYEING MACHINE – JIGGER
15 INSPECTION MACHINE
16 MACHINES FOR BONDING PIECES (GOODS)
18 WINDING MACHINE
19 INSPECTION MACHINE
20 MEASURING WINDING MACHINE
21 HEAT EXCHANGER
DOUBLING MACHINE

YARN DYEING AND DRYING:
1 DYEING APPARATUS
2 DYEING APPARATUS
3 DYEING APPARATUS
4 PRESSURE DRYING APPARATUS – TANDEM
5 DYEING APPARATUS
6 DYEING APPARATUS
7 THE LOADING AND UNLOADING DEVICE
8 BRIDGE CRANE
9 PROCESS WATER REGENERATION + TANK

SEWING:
8 SEWING MACHINE FOR WASHING GLOVES
9 CONTROL TABLES
10 PACKING MACHINES

DOUBLING, TWISTING, WARPING AND WEAVING:
3 WINDING MACHINE
4 MOBILE REGALS FOR YARN STORAGE

WARPING AND WEAVING:
1 WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
2 WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
3 WARPING MACHINE
4 SIZING MACHINE
5 SIZING MACHINE
13 COMPRESSOR FOR COMPRESSED AIR
14 KNOTTING MACHINES
15 ELEVATOR FOR BEAMS
16 ELEVATOR FOR BEAMS
17 PUNCH MACHINE
18 ELEVATOR FOR BEAMS
19 MOBILE REGALS FOR BEAM STORAGE

WEAVING SAURER 1;2;3;4:
STAUBLI JACQUARD – WITH 560 HOOKS X 4 – 10 PIECES
STAUBLI JACQUARD – WITH 768 HOOKS X 4 – 4 PIECES
STAUBLI JACQUARD – WITH 1120 HOOKS X 2 - 2 PIECES
STAUBLI JACQUARD – WITH 912 HOOKS X 2 – 1 PIECE

WEAVING SILK:
WEAVING MACHINE – LOOMS SM 93
CONTROL TABLE

READY MADE DEPARTMENT FOR TERRY BATHROBES:
CUTTING TABLE – BULLMERWERK – 1 PIECE
SEWING MACHINE – JUKI – 2 PIECES
SEWING MACHINE – JUKI – 1 PIECE
SEWING MACHINE – JUKI – 1 PIECE
SEWING MACHINE –LEVIS – 1 PIECE
SEWING MACHINE – PFAFF – 2 PIECES
SEWING MACHINE – JUKI – 2 PIECE
SEWING MACHINE – MAUSER SPECIAL – 1 PIECE
SEWING MACHINE – PFAFF – 2 PIECES
SEWING MACHINE – 1 PIECE
SEWING MACHINE – NECCHI – 4 PIECES
SEWING MACHINE – PFAFF – 1 PIECE
SEWING MACHINE – JUKI – 1 PIECE

LABOR MACHINES:
APPARATUS FOR MEASURING ZTWIST, TURN/ROLL – TORSIOMETER
APPARATUS FOR MEASURING THE FRICTION COEFFICIENT
LIGHTING CHAMBER
AA WINDING APPARATUS FOR THE DYEING TUBE THE SAMPLING DEVICE
WINDING APPARATUS FOR COLOR STANDARDS
YARN DYEING APPARATUS PRETEMA MULTICOLOR
DYNAMOMETER FOR SPINNING
SPEKTROFOTOMETER DATACOLOR INTERNATIONAL – LABOR MACHINE
APPARATUS FOR THE VISUAL APPEARANCE OF THE YARN – LABOR MACHINE

ADDITIONAL DESCRIPTION

PLAIN DYEING AND FINISHING EQUIPMENT:
7. DYEING MACHINE
SCHIRM
MODEL: SURFER
YEAR: 1994
CAPACITY : 380 – 400 KG
TECHNICAL INFORMATION:
WOVEN TERRY DYEING, WASHING AND BLEACHING AIR - FLOW
WORKING TEMPERATURE: UP TO 98˚ C (NOT HT)
SEDOMAT PC 3100
QUANTITY: 1 (NO 94)

9. AUTOMATIC DOSING SYSTEM
LAWER
YEAR: 2002
CHEMICAL DISPENSING SYSTEM
20 PVC TANKS (CAPACITY 200 L TO 1200 L)
2 EXTERNAL TANKS CAPACITY 1500 L
TRANSFER PUMP
QUANTITY: 1

10. DYEING MACHINE - JIGGER
MCS
MODEL: S - 300 MCS
YEAR: 1993
TECHNICAL INFORMATION:
WORKING WIDTH : 3000MM
WOVEN FABRIC DYEING, WASHING AND BLEACHING AIR -FLOW
WORKING TEMPERATURE: UP TO 98˚ C (NOT HT)
MICROPROCESOR CT400
DIMENSIONS LENGTH 65000 MM X WIDTH 43000 MM X HEIGHT 25000 MM
INSTALLED ELECTRIC POWER: 3 X 63 A
QUANTITY: 1(NO 54)

11. DYEING MACHINE - JIGGER
MCS
MODEL: S - 300 MCS
YEAR: 1993
TECHNICAL INFORMATION:
WORKING WIDTH : 1600MM
WOVEN FABRIC DYEING, WASHING AND BLEACHING AIR - FLOW
WORKING TEMPERATURE: UP TO 98˚ C (NOT HT)
MICROPROCESOR CT400
THE HYDRAULIC SYSTEM HAS FAILED/NOT WORKING
DIMENSIONS LENGTH 5,300 CM X WIDTH 4,300 CM X HEIGHT 2,500 CM
QUANTITY: 1(NO 53)

15. INSPECTION MACHINE
MONFORTS
TECHNICAL INFORMATION:
MACHINE FOR INSPECTING THE GOOD
QUANTITY: 1

16. MACHINE FOR BONDING PIECES (GOODS)
GEBRUDER DOHLE
MODEL: 799/03
TECHNICAL INFORMATION:
SEWING MACHINE USED FOR BONDING GOODS
QUANTITY: 2

18. WINDING MACHINE
MARK: AEG
TECHNICAL INFORMATION:
WINDING GOODS
QUANTITY: 1

19. INSPECTION MACHINE
MONFORTS
MODEL: MBH
YEAR: 1977
TECHNICAL INFORMATION:
MACHINE FOR INSPECTING THE GOOD
QUANTITY: 1

20. MEASURING WINDING MACHINE
MENZEL
MODEL: MWE2
YEAR: 1986
TECHNICAL INFORMATION:
WINDING DIFFERENT LENGTHS OF GOOD
QUANTITY: 1

21. HEAT EXCHANGER
PT-S
YEAR: 2002
TECHNICAL INFORMATION:
RECUPERATION
QUANTITY: 1

23. DOUBLING MACHINE
MODEL: MLH
YEAR: 1975
TECHNICAL INFORMATION:
DOUBLING AND COMPOUNDING GOODS
QUANTITY: 1

YARN DYEING AND DRYING:
1. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS
TYPE: 1250
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY:
6 INCHES BOBBIN : MAX 336 KG, MIN. 134 KG
5 INCHES BOBBIN : MAX 235 KG, MIN. 98 KG
WORKING TEMPERATURE: UP TO 140˚ C
PRESSURE : UP TO 4.5 BAR
BARCO SEDO SEDOMAT 3500
QUANTITY: 2 PCS (NO 12, NO 14)

2. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS
TYPE: 850
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY;
6 INCHES BOBBIN : MAX 144 KG, MIN. 58 KG
5 INCHES BOBBIN : MAX 100 KG, MIN. 42 KG
WORKING TEMPERATURE: UP TO 140˚ C
PRESSURE : UP TO 4.5 BAR
BARCO SEDO SEDOMAT 3500
THICKNESS OF PLATE = 30 CM
PART OF A MACHINE IN THE BASEMENT, HEIGHT = 2.00 CM
DIMENSIONS: LENGTH 3100MM X WIDTH 2000MM X HEIGHT 1800MM X HEIGHT 2900MM
INSTALLED ELECTRIC
POWER: 45 KW
CUPBOARD FOR ELECTRONICS:
LENGTH 2500MM X WIDTH 600MM
INSTALLATION OF THE SOIL = 60CM DEEPER
(APPLY TO ALL INSTALLATION)
QUANTITY: 1(NO 18)

3. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS TYPE 600
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY:
6 INCHES BOBBIN: MAX 84 KG, MIN. 34 KG
5 INCHES BOBBIN: MAX 59 KG, MIN. 26 KG
WORKING TEMPERATURE: UP TO 140˚ C
PRESSURE : UP TO 4.5 BAR
BARCO SEDO SEDOMAT 3500
DIMENSIONS: LENGTH 2500MM X WIDTH 2000MM X HEIGHT 1800MM X HEIGHT 2900MM
INSTALLED ELECTRIC POWER: 17 KW
CUPBOARD FOR ELECTRONICS:
LENGTH 2500MM X WIDTH 600MM
QUANTITY: 1(NO 16)

4. PRESSURE DRYING APPARATUS – TANDEM
JASPER
YEAR: 1998
TECHNICAL INFORMATION:
DIMENSION: LENGTH 290CM WIDTH 3300MM X HEIGHT 1800MM X HEIGHT 2900MM
CUPBOARD FOR ELECTRONICS
LENGTH 250CM X WIDTH 60CM
QUANTITY: 2 TANDEM WORKING AS ONE UNIT

5. DYEING APPARATUS
JASPER
MODEL: DYEING APPARATUS
TYPE: 1250
YEAR: 1998
TECHNICAL INFORMATION:
DYEING APPARATUS WITH VARIABLE VOLUME OF BATH
CAPACITY:
6 INCHES BOBBIN : MAX 336 KG, MIN. 134 KG
5 INCHES BOBBIN: MAX 235 KG, MIN. 98 KG
WORKING TEMPERATURE: UP TO 98˚ C
PRESSURE: UP TO 4.5 BAR
MANUAL PROCESSOR
DIMENSIONS: LENGTH 2800MM X WIDTH 3100MM X HEIGHT 2500MM X HEIGHT 2900MM
(WITH A DOSING DEVICE IN THE FORM OF "V")
INSTALLED ELECTRIC
POWER: 45 KW
CUPBOARD FOR ELECTRONICS: LENGTH 2500MM X WIDTH 60MM
QUANTITY: 1 (NO 13)

6. DYEING APPARATUS
THEN
MODEL: HL 40/7,8
YEAR: 1986
WIDTH: 1800MM
5 INCHES BOBBIN: MAX 12 PIECES
WORKING TEMPERATUR: UP TO 140˚ C
HEIGHT: 2160MM
PRESSURE: UP TO 4,5 BAR
INSTALLED ELECTRIC POWER – 3X16 A
TECHNICALINFORMATION: DYEING APPARATUS
DIMENSIONS: LENGTH 1600MM
QUANTITY: 1

7. THE LOADING AND UNLOADING DEVICE
JASPER
YEAR: 1998
TECHNICAL INFORMATION; LOADING DEVICE FOR BOBBINS
THICKNESS OF PLATE = 300MM (APPLY TO ALL INSTALLATIONS)
PART OF A MACHINE IN THE BASEMENT, HEIGHT = 2000MM (APPLY TO ALL INSTALLATION)
DIMENSIONS : Ø 1700MM : HEIGHT1600MM
INSTALLED ELECTRIC POWER : 10KW
QUANTITY: 1

8. BRIDGE CRANE
TECHNICAL INFORMATION:
THE CARGO TRANSFER
QUANTITY : 2

9. PROCESS WATER REGENERATION + TANK
JASPER
TECHNICAL INFORMATION:
STORAGE OF WATER FOR THE PRODUCTION PROCESS
QUANTITY : 1

SEWING:
8. SEWING MACHINE FOR WASHING GLOVES
TEXPA ARBTER
MODEL: WASCHLA 10
YEAR: 1994
TECHNICAL INFORMATION:
SEWING WASHING GLOVES, FITTING LABELS AND CORD.
QUANTITY: 1

9. CONTROL TABLES
TECHNICAL INFORMATION:
GOOD INSPECTION AND WEIGHING
QUANTITY: 3

10. PACKING MACHINE
BECK
TECHNICAL INFORMATION:
PACKING TOWELS INTO FOIL
QUANTITY: 1

3. WINDING MACHINE
SCHLAFHORST
MODEL: BKN
YEAR: 1975
TECHNICAL INFORMATION:
96 PIECES SPINDLES (2 X 48 SPINDLES)
QUANTITY: 2

4. MOBILE REGALS FOR YARN STORAGE
INCLUDED SELLING YARN
QUANTITY: 3

WARPING AND WEAVING:
1. WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
HACOBA
MODEL: USK T1000/SM
YEAR: 1990
TECHNICAL INFORMATION:
ELEKTRONIC COMPUTER, AUTOMATIC SETTING OF CONE,
DEVICE FOR CROSSING THE FLOOR DIVISION THREADS
PRELIMINARY SETTING : OF LENGTH IN METERS (YARN LEGTH RECORDER), NUMBER OF REVOLUTIONS, …
CONE CREEL/CREELS 2 X 32 CROSS-WOUND COME (MAX. DIAMETER CROSS-WOUND IS 225 MM)
WETTING TROUTH FOR COLD STARCHING BY APPLICATOR ROLLER
MAXIMUM WARPING WIDTH : 240 CM/ WARPING WIDTH (MARKED) 240 CM
QUANTITY: 1

2. WARPING MACHINE FOR WARPING BY SECTION AND WARPING REEL
SUCKER MÜLLER HACOBA
MODEL: USK -S/SM
YEAR: 1998
TECHNICAL INFORMATION:
MAXIMUM WARPING WIDTH : 2000MM
QUANTITY: 1

3. WARPING MACHINE
BENNINGER
MODEL: 97126 FB
YEAR: 1978
TECHNICAL INFORMATION:
MAX. NUMBER OF CONES 704
QUANTITY: 1

4. SIZING MACHINE
BENNINGER ZELL
MODEL: BZ-7M
YEAR: 1975
TECHNICAL INFORMATION:
MAXIMUM WORKING WIDTH 2400MM
TOTAL BEAM 8 PCS
DRUM DRYER TEFLONIZED
MAHLO MOISTURE CONTROL
SIZING KITCHEN
QUANTITY: 1

5. SIZING MACHINE
BENNINGER ZELL
MODEL: XK Z6F
YEAR: 1986
TECHNICAL INFORMATION:
MAX. WORKING WIDTH 240 CM
TOTAL BEAM 12 PCS
DRUM DRYER TEFLONIZED
MAHLO MOISTURE CONTROL
QUANTITY: 1

13. COMPRESSOR FOR COMPRESSED AIR
KAESER
MODEL: CS 76, ABT 72
YEAR: 2003
NO. OF MASHINES: 3

14. KNOTTING MACHINE
KNOTEX
MODEL: AS/2 8013 EA03
YEAR: 2002
TECHNICAL INFORMATION:
WITH TWO TROLLEY SIZE 2500MM
QUANTITY: 5

15. ELEVATOR FOR BEAMS
GENKINGER
MODEL: EE-KHHR
YEAR: 1998
TECHNICAL INFORMATION:
LIFTING UP THE WEAVING BEAMS
QUANTITY: 1

16. ELEVATOR FOR BEAMS
HUBTEX
MODEL: KHHW
YEAR: 1988
TECHNICAL INFORMATION:
LIFTING UP THE WEAVING BEAMS
QUANTITY: 1

17. PUNCH MACHINE
GROSSE
MODEL: LSE 600
YEAR: 1998
TECHNICAL INFORMATION:
PUNCHING CARDS
QUANTITY: 1

18. ELEVATOR FOR BEAMS
TECHNICAL INFORMATION:
LIFTING UP THE WEAVING BEAMS
QUANTITY: 1

19. MOBILE REGALS FOR BEAM STORAGE
TECHNICAL INFORMATION:
UP - DOWN MOVING REGALS
QUANTITY: 13

WEAVING SAURER 1;2;3;4:
1. STÄUBLI JACQUARD
WITH 560 HOOKS X 4
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 10

2. STÄUBLI JACQUARD
WITH 768 HOOKS X 4
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 4

3. STÄUBLI JACQUARD
WITH 1120 HOOKS X 2
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 2

4. STÄUBLI JACQUARD
WITH 912 HOOKS X 2
COMPATIBLE LOOMS
WITH SAURER DIETRICH, MODEL S400, WIDTH 2250MM
2-3 PRE-WINDERS PER LOOM
NUMBER OF MASHINES: 1

WEAVING SILK:
1. WEAVING MACHINE
SOMET
MODEL: MASTER SM93
YEAR OF CONSTRUCTION: 1990
TECHNICAL INFORMATION:
WITH STÄUBLI JACQUARD, JC4 CONTROLLER
5-6 PRE-WINDERS PER LOOM
NUMBER OF MACHINES: 2

2. CONTROL TABLE
TECHNICAL INFORMATION:
GOOD INSPECTION
NUMBER OF MACHINES: 1

READY MADE DEPARTMENT FOR TERRY BATHROBES:
1. CUTTING TABLE
BULLMERWERK
MODEL: KOMET II
TECHNICAL INFORMATION:
CUTTING GOODS BY CUTTING PATTERNS FOR TERRY
BATHROBES
QUANTITY: 1

2. SEWING MACHINE
JUKI
TECHNICAL
INFORMATION:
SEWING TERRY
PRODUCTS
QUANTITY: 2

3. SEWING MACHINE
JUKI
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 1

5. SEWING MACHINE
JUKI
TECHNICAL
INFORMATION:
SEWING TERRY
PRODUCTS
TRIPLE STICH OVERLOK
QUANTITY: 1

6. SEWING MACHINE
LEWIS
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
BLIND STICH
QUANTITY: 1

7. SEWING MACHINE
PFAFF
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 2

8. SEWING MACHINE
JUKI
TECHNICAL
INFORMATION:
SEWING TERRY PRODUCTS
OVERLOK
QUANTITY: 2

9. SEWING MACHINE
MAUSER SPECIAL
TECHNICAL INFORMATION:
SEWING NAPKINS
OVERLOK
QUANTITY: 1

10. SEWING MACHINE
PFAFF
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 2

11. SEWING MACHINE
TECHNICAL INFORMATION:
SEWING MACHINE USED FOR BONDING GOODS
QUANTITY: 1

12. SEWING MACHINE
NECCHI
TECHNICAL INFORMATION:
SEWING MACHINE USED FOR
BONDING GOODS
QUANTITY: 4

13. SEWING MACHINE
PFAFF
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 1

14. SEWING MACHINE
JUKI
TECHNICAL INFORMATION:
SEWING TERRY PRODUCTS
QUANTITY: 1

LABOR MACHINES:
1. APPARATUS FOR MEASURING ZTWIST, TURN/ROLL - TORSIOMETER
MARK: CALDERARA BOSI
YEAR: 1989
QUANTITY: 1

2. APPARATURS FOR MEASURING THE FRICTION COEFFICIENT -
ZWEIGLE
MODEL: µ-METER G 530
TYPE: 530
YEAR: 1972
TECHNICAL INFORMATION:
NOT WORKING
QUANTITY: 1

3. LIGHTING CHAMBER

MARK: DATACOLIR INTERNATIONAL
YEAR: 2004
TECHNICAL INFORMATION:
FROM 4 TYPES OF LIGHT ONLY WORKS 1
QUANTITY: 1

4.AA WINDING APPARATURS FOR THE DYEING TUBE THE SAMPLING DEVICE
ZWEIGLE (REUTLIGEN)
QUANTITY: 1

5. WINDING APPARATURS FOR COLOR STANDARDS
IZDELANO V SVILANITU
YEAR: 2001
QUANTITY: 1

6. YARN DYEING APPARATURS PRETEMA MULTICOLOR
PRETEMA
MODEL: TYPE MC-320
YEAR: 1982
TECHNICAL INFORMATION:
V 22 W 1800
DIMENSIONS: LENGTH 119 CM X WIDTH 61 CM X HEIGHT 126 CM
INSTALLED ELECTRIC POWER: 1800 W
QUANTITY: 1

7. DYNAMOMETER FOR SPINNING
KARL SCHRÖDER
YEAR: 1977
QUANTITY: 1

8. SPEKTROFOTOMETER DATACOLOR INTERNATIONAL
DATACOLOR INTERNATIONAL
MODEL: SPECTRAFLASH SF600 PLUS CT
YEAR: 1999
TECHNICAL INFORMATION:
RATINGS: 100-240 V ̴47-63 HZ, 100 VA
NOT WORKING (DO NOT KNOW THE TYPE OF TROUBLE)
QUANTITY: 1

9. APPARATURS FOR THE VISUAL APPEARANCE OF THE YARN
ZWEIGLE KG REITLINGEN
QUANTITY: 1

QUANTITY: 1 COMPLETE PLANT

Learn More

C-4355 FULL-AUTO WET TISSUE FOLDING MACHINE Y-12 AND FULL-AUTO WET TISSUE PACKING MACHINE Y-360, CAPACITY 40 TO 120 PCS/PACKAGE

OFFER 001
Y-360 FULL AUTOMATIC RECIPROCATING TYPE PACKING MACHINE
PRODUCTION TYPE: BABY WET TISSUE
PRODUCTION PROCESS: CONNECT TO Y-2700 FOLDING MACHINE (OR Y-12 FOLDING MACHINE) → FEEDING WIPE AUTOMATIC →CONVEYING TO PACKING MACHINE → SETTING PACKING FILM → SETTING WINDOW HOLE LABEL → CENTRAL SEALING →END SEALING AND RECIPROCATING CUT → OUTPUT FINISHED PRODUCTS.
MAINTECHNICAL PARAMETER: (SUITABLE TO PACK: 5 TO 120PCS/BAG)
PRODUCT SPEED: 55 TO 60 BAG/MIN
DIAMETER OF RAW FILM ROLL: ≤380mm
WIDTH OF RAW FILM ROLL: ≤420mm
WRAPPING MATERIAL: PP, OPP, PET, PE, AND ALL SUITABLE FILMS
SHAPES OF PACKING: PILLOW TYPE PACKAGING
PACKING LENGTH: 110 TO 300mm (TOUCH SCREEN SETABLE)
PACKING WIDTH: 80 TO 150mm (ADJUSTABLE)
HEIGHT OF PACKING: 10 TO 100mm (ADJUSTABLE)
HORIZONTAL SEALING PATTERN: RECIPROCATION HEAT SEALING
DRIVE MOTOR PATTERN: ALL SERVO DRIVE
CONTROL PATTERN: YASKAWA SIMOTION CONTROL SYSTEM
OPERATION INTERFACE: 7 INCH LCD
FILM SUPPLY SYSTEM: SERVO DRIVE
HORIZONTAL SYSTEM: SERVO DRIVE
FEEDING SYSTEM: SERVO DRIVE
LABELING SYSTEM: SERVO DRIVE
PUNCHING SYSTEM: SERVO DRIVE
HORIZONTAL PROTECTION: TORQUE OVERLOAD PROTECTION
AIR REQUIREMENTS: 0.5 TO 0.8 MPA 0.01 M3/MIN
ELECTRIC POWER REQUIREMENTS: 380VAC 50/60HZ
GENERAL POWER: 7.6KW
DIMENSION OF MACHINE: 3610 × 1150 × 1900mm
STANDARD EQUIPMENT: DATE PRINTING UNIT, PUNCHING UNIT, LABELLING UNIT, INSERTING CORNER UNIT, ELECTRICAL EYE TRACKING AUTOMATICALLY
(2) SYSTEM CHARACTER
1. THE PACKING FILM ADOPTS MECHNICAL TENSION CONTROL
2. TWO LABEL MACHINE, ONE SUB-LABELING, THE OTHER IS ANTI-COUNTERFEITING LABEL
3. PUNCHING AT THE PACKING FILM AUTOMATICALLY
4. HEATING PRINTING (DATE) DEVICE
5. FOUR BACK AND FORTH TRANSVERSE SEALING DEVICE WITHINSERT CORNER BY CYLINDER FORM
6. EIGHT SERVO MOTORS, CONTROLLING FEEDING PACKING FILM, TRANSVERSE SEALING, FEEDING TISSUE RESPECTIVELY
7. LENGTHWAYS SEALING DEVICE, CONTROL THEOPEN-CLOSEBY CYLINDER. THE SEALING WHEEL ARE APART AUTOMATICALLY WHEN THE MACHINE STOPS
8. PUNCHING, LABELING AND THE EYE MARK’S RELATIVED POSITION CAN BE SET IN THE TOUCH SCREEN.
9. AUTOMATIC FEEDING RAW MATERIAL DEVICE
10. COLOUR TOUCH SCREEN, MOTION SYSTEM CONTROL
11. MAIN MOTOR ADOPTS FAMOUS BRAND
12. MAIN MACHINE ADOPTS FRAMES FORM

OFFER 002
Y-360 FULL AUTOMATIC RECIPROCATING TYPE PACKING MACHINE
YASKAWA ELECTRICITY FROM JAPAN
ITEM NUMBER: 1
MOTION CONTROLLER
JEPMC-MP2300S-E
YASKAWA
QUANTITY: 1
ITEM NUMBER: 2
EXTENDED MODULE
R7K4FML-6-DCA32A
YASKAWA
QUANTITY: 1
ITEM NUMBER: 3
SERVO MOTOR/SERVO UNIT
SGMJV-08ADE6S /SGDV-5R5A11A
YASKAWA 750W
QUANTITY: 5
ITEM NUMBER: 4
SERVO MOTOR/SERVO UNIT
SGMGV-13ADC61 /SGDV-120A11A
YASKAWA 1.3KW
QUANTITY: 1
ITEM NUMBER: 5
SERVO MOTOR/SERVO UNIT
SGMGV-20ADA61/SGDV-180A11A
YASKAWA 1.8KW
QUANTITY: 1
ITEM NUMBER: 6
SERVO MOTOR/SERVO UNIT
SGMGV-09ADC61/SGDV-7R6A11A
YASKAWA 0.85 KW
QUANTITY: 1
ITEM NUMBER: 7
POWER CABLE + ENCODER CABLE
JZZP-CVM09/JZSP-CVP02-05
YASKAWA 850W
QUANTITY: 1
ITEM NUMBER: 8
POWER CABLE + ENCODER CABLE
JZSP-CMM00-05 JZSP-CMP00-05
YASKAWA 750W
QUANTITY: 7
ITEM NUMBER: 9
POWER CABLE + ENCODER CABLE
JZSP-CVM30-05 JZSP-CVP02-5
YASKAWA 1.3KW, 1.8KW
QUANTITY: 2
ITEM NUMBER: 10
COMMUNICATION CABLE
JEPMC-W6002-05
QUANTITY: 12
ITEM NUMBER: 11
TERMINAL RESISTANCE
JEPMC-W6022-E
QUANTITY: 2
ITEM NUMBER: 12
TOUCH PANEL
WEINVIEW
7 INCH
QUANTITY: 1
ITEM NUMBER: 13
AIR BREAK SWITCH
LG
QUANTITY: 12
ITEM NUMBER: 14
RESIDUAL CURRENT CIRCUIT BREAKER
CHINT
QUANTITY: 1
ITEM NUMBER: 15
CONTACTOR (SWITCH)
SCHNEIDER
QUANTITY: 1
ITEM NUMBER: 16
POWER SWITCH
M&W
350W
QUANTITY: 1
ITEM NUMBER: 17
SOLID STATE RELAY (SSR)
ANV
QUANTITY: 6
ITEM NUMBER: 18
TEMPERATURE CONTROLLER
DTE10P
QUANTITY: 1
ITEM NUMBER: 19
RELAY
OMRON
QUANTITY: 4

OFFER 003
Y-12 BABY WIPES FOLDING MACHINE
PRODUCTION FLOW: UNROLLING - SLITTING FABRIC INTO LANES - FOLDING - WETTING - CUTTING – PILE & COUNTING - DELIVERING
MAIN TECHNICAL PARAMETER (SUITABLE TO WET TISSUE FOR LARGE SIZE PACKING)
PRODUCT TYPE: BABY WIPES (NON CROSS FOLDING)
PRODUCT SPEED: 200 TO 270 CUTS/MIN (SET ON PLC)
SUITABLE RAW MATERIAL: AIR LAID PAPER, SPUNLACE/HOT-ROLLING NONWOVEN FABRIC
WEIGHT OF RAW MATERIAL: 40-80G/㎡
FOLDING WAY: “Z” SHAPE (POP UP AND NON-POP UP)
CUTTING UNITE:
A. DOUBLE PAPER SHELVES
B. 10 LANES OR 12 LANES, 2 ROLLS
C. RAW MATERIAL ROLL WIDTH: 900 TO 1200mm
LENGTH OF WET TISSUE: 140 TO 185mm (SET ON PLC)
FREQUENCY OF RECEIVING PAPER: 14 TO 20 TIMES/MIN (SET ON PLC)
SIZE OF RAW MATERIAL: (1000 TO 1250) × Ø1000 (mm, W×DIA)
WET TISSUE UNFOLDED SIZE: (140 TO 185) × (150 TO 200) (mm, L×W)
WET TISSUE FOLDED SIZE: (140 TO 185) × (80 TO 110) (mm, L×W)
MATERIAL SUPPLY SYSTEM: SERVO MOTOR
CUTTING SYSTEM: CONVERTER MOTOR
PILING SYSTEM: SERVO MOTOR
POWER SUPPLY: 380V 50HZ

OFFER 004
Y-12 WET TISSUE FOLDING MACHINE
MAIN PARTS
ITEM NUMBER: 1
PLC
FX3U-32T
MITSUBISHI (JAPAN)
QUANTITY: 1
ITEM NUMBER: 2
SERVO MOTOR (CONTROL THE DISTANCE OF TISSUE
ASD-B2-2023-B, ECMA-E21320RS
3.0KW DELTA (TAIWAN)
QUANTITY: 1
ITEM NUMBER: 3
SERVO MOTOR (RECEIVING TISSUE)
ASD-B2-0721-B, ECMA-C20807RS
750W DELTA (TAIWAN)
QUANTITY: 1
ITEM NUMBER: 4
TURBINE WORM REDUCER MOTOR
WPDA120-1:10-Y100L2-4
3KW NANJING UTTON (CHINA)
QUANTITY: 1
ITEM NUMBER: 5
INVERTER
SB70G4
4KW SENLON
QUANTITY: 1
ITEM NUMBER: 6
TOUCH SCREEN
7INCH
WECON
QUANTITY: 1
ITEM NUMBER: 7
AIR SWITCH
LG
QUANTITY: 1
ITEM NUMBER: 8
SWITCHING POWER SUPPLY
S-100-24
SHANGHAI MINGWEI (CHINA)
QUANTITY: 1
ITEM NUMBER: 9
INDICATOR LIGHT
SCHNEIDER
SCHNEIDER (GERMAN)
QUANTITY: 1
ITEM NUMBER: 10
EMERGENCY STOP SWITCH
SCHNEIDER
SCHNEIDER (GERMAN)
QUANTITY: 1
ITEM NUMBER: 11
POTENTIOMETER
5KΩ
QUANTITY: 1
ITEM NUMBER: 12
ROTARY ENCODER
INCREMENTAL POLE OUTPUT
KOYO (JAPAN)
QUANTITY: 1
ITEM NUMBER: 13
RELAY
OMRON
OMRON (JAPAN)
QUANTITY: 5
ITEM NUMBER: 14
PROXIMITY SWITCH
AUTONICS
AUTONICS (KOREA)
QUANTITY: 2

Learn More

REFERENCE NUMBER: P-4332

WET WIPES FOLDING MACHINE

 

MODEL RF

Machine  Characteristic:
Control system: PLC
Drive element: inverter control
Operate interface: LCD touch screen
Detection online: splicing  connector detect
Auto splicing: raw material automatic  splicing
Wipes counting: auto counting, set by LCD
Flow control: 2.5-4 times moisture
Moisture type: 2 liquid pipes spray
Cutting: stainless steel round knife
Protective alarm: breakdown alarm and stop

Specifications:
Raw material: spunlaced nonwoven, therbond etc. nonwoven
Raw material specification: max W250mm, Φ1100mm
Axis QTY settings: 2 rolls raw material, auto splicing
Diameter of ventilating shaft: 3"
Folding type: Z, W fold
Wet wipes size: L100mm  W50-100mm (special  specifications need be marked)
Open size: L200mm  W140-250mm
Production speed: 500-600 pieces/min, design 650 pieces/min
Machine space: L4900mm  W1200mm  H1500mm
Power: AC 380V  50/60Hz  4KW
Compressed air: 0.6-0.8Mpa   100L/min
Machine  net  weight: 2000kg

Option  equipment:  Stainless steel agitate tank Automatic  Knife  grinder

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: P-4333

DRY WIPES FOLDING MACHINE

 

Model: TF
Machine Characteristic
Control system: PLC
Drive element: inverter control
Operate interface:  LCD touch screen
Detection online: bonding connector detect
Auto splicing: raw material automatic splicing 
Wipes counting: auto counting, set by LCD
Cutting: endless-belt type knife
Cut polish: sharpen online, intelligent control
Protective alarm: breakdown alarm and stop
Specifications
Raw material: spunlaced nonwoven, therbond etc.  nonwovens
Raw material specification: max W300mm, φ1100mm
Axis QTY settings:2 rolls raw materials , auto splicing
Diameter of ventilating shaft: 3"
Folding  type: Z, W fold
Wet wipes size:L150mm  W50-150mm(special specifications need be marked)
Open size: L300mm W150-300mm
Production speed: 500-600 pieces/min ,design 600 pieces/min
Machine space: L4700mm W1200mm H2200mm
Power: AC 380V 50/60Hz 4KW
Compressed air: 0.6-0.8Mpa 100L/min
Machine net weight :  2000kg

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: V-1468

SURGICAL GAUZE COMPRESSING, FOLDING, AND BAGGING MACHINE

 

COTTON GAUZE MEDICAL COMPRESS FOLDING AND BAGGING MACHINE, WHICH AUTOMATICALLY FOLDS COTTONG GAUZE, COMPRESSES, AND THEN PACKS THEM INDIVIDUALLY OR IN GROUPS INTO SACHETS.

 

FEATURES             

 

USEFUL WIDTH: 45 CM

 

NUMBER OF TRACKS: MAXIMUM 2 (VARIES ACCORDING TO THE SIZE OF COMPRESSES)

 

SIZE:

MINIMUM DIMENSIONS OF COMPRESSES: 5 CM X 5 CM

MAXIMUM DIMENSIONS OF COMPRESSES: 10 CM X 20 CM (16 PLIES)

ALL THE USUAL OR INTERMEDIATE SIZES CAN BE PRODUCED ON THE MACHINE BY SIMPLE ADJUSTMENTS.

 

NUMBER OF PLIES 8 / 12 / 16 / 20 / 24 / 28 / 32 PLIES (VARIES ACCORDING TO THE SIZE OF COMPRESSES)

 

FOLDING: THE CONVENTIONAL FOLDING IS THE 5-FOLD "SURGICAL" OR "AMERICAN" TYPE, WITH EDGES AND CORNERS TUCKED-IN, HOWEVER BY OFFSETTING FOLDS OTHER COMBINATIONS ARE POSSIBLE.

 

STACKING:  STACKING IS CARRIED OUT IN THE CHANNELS WHERE THE COMPRESSES ARE COUNTED AND READY TO BE MANUALLY INSERTED INTO PAPER BAGS.

 

PRODUCTION      :

EXAMPLES OF THEORETICAL PRODUCTIONS:

5 CM X5 CM 8 PLIES (2 TRACKS) 13200 COMPRESSES PER HOUR

7.5 CM X 7.5 CM 12 PLIES (2 TRACKS) 13200 COMPRESSES PER HOUR

10 CM X 10 CM 12 PLIES (2 TRACKS) 12000 COMPRESSES PER HOUR

 

OPTIONS:

BARIUM FIXING TRACK BY TRACK

GAUZE ROLL LOADING BY PNEUMATIC CYLINDERS"

FEATURES LIST:

MATERIAL SUPPORT ADJUSTABLE IN WIDTH,

POSITIVE UNWINDING WITH TENSION CHECK ADJUSTABLE TRACK BY TRACK,

MULTIPLE LENGTH FOLDING DEVICE ADJUSTABLE TRACK BY TRACK,

SPRAY HUMIDIFYING SYSTEM,

SUCTION SYSTEM,

ANTI-STATIC BARS,

ADJUSTABLE FLY CUT MODULE MOTORISED WITH BRUSHLESS MOTOR,

THREE CROSS FOLDING MECHANISMS WITH INDEPENDENT ADJUSTMENT OF EACH FOLD,

TRANSFER BELTS FOR THE COMPRESSES,

MOTORISED LATERAL UNWINDING OF THE PAPER ROLL MODULE,

DEVICE FOR INDIVIDUAL, IN MULTIPLES OR IN SHINGLED FORM PACKAGING - WITH A CHANGEABLE

NUMBER OF COMPRESSES BY SACHET,

CHECK OF FOLLOWING OPERATIONS TRACK BY TRACK:

. END OF FABRIC,

. PRESENCE OF SEAM,

. PRESENCE OF CROSS-FOLDED COMPRESS,

. JAM PREVENTION BEFORE PACKAGING.

COLD SEALING BY PRESSURE AND CUTTING OF SACHETS IN PRINTED AND ZONED PAPER,

POWER SYSTEM OF PACKAGING BY BRUSHLESS MOTOR ALLOWING FOR FLY ADJUSTMENT OF:

. THE COMPRESS POSITION IN THE SACHET,

. THE CROSSWISE KNURLING POSITION,

. THE CROSSWISE CUTTING OF SACHETS.

ACCELERATION RAMP BY FREQUENCY VARIATION,

MACHINE OPERATION BY TOUCH-SENSITIVE SCREEN:

. STORABLE CONFIGURATIONS,

. CLEAR LANGUAGE FAULT DISPLAY,

. COUNTERS : TOTALIZER, PRE-SELECTION, ETC.,

. SOUND AND VISUAL ALARMS,

. "INCIDENT" STATISTICS.

STARTING, STOPPING, STEP BY STEP - BY REMOTE CONTROL.

* CONTINUOUS, TRACK BY TRACK INTEGRATION OF ULTRASONIC BARIUM FIXING.

* PAPER ROLL LOADING BY PNEUMATIC CYLINDERS.

* INK JET MARKING UP TILL 8 LINES.

* SACHETS QUALITY CONTROL DEVICE: EITHER A CHECK BY PHOTO CELLS, OR BY CAMERAS,

* FAULTY SACHET EJECTION DEVICE.

* TABLE WITH CONVERGING BELTS.

Learn More

C-3983 HACOS VAN MEULENBEKE ROBY 450 ENROBER FOR CHOCOLATE, WIDTH 1mm, YEAR 2007

HACOS VAN MEULENBEKE ROBY 450 ENROBER
YEAR: 2007
FOR CHOCOLATE
NO TEMPERER OR COOLING TUNNEL
MANUFACTURER: HACOS VAN MEULENBEKE
MODEL: ROBY 450
LENGTH: 0.04 IN (1mm)
WIDTH: 0.04 IN (1mm)
HEIGHT: 0.04 IN (1mm)

QUANTITY: 1

Learn More

REFERENCE NUMBER: A-1342 (0303138DLA02RFL) A CONTINUOUS FOULARD TUMBLER AND STENTER DRYING MACHINE WORKING TERRY CONTINUOUS FOULARD TUMBLER AND STENTER DRYING MACHINE WORKING TERRY MARK: BABCOCK, KRANTZ, MAHLO YEAR: 1999 WORKING WIDTH: 2450mm 4 STATIONS GAS HEATING WEFT STRAIGHTENING EQUIPMENT QUANTITY AVAILABLE: 12 Learn More

REFERENCE NUMBER: K-1324 EMBROIDERY MACHINE FOR PILLOWS THIS SPECIAL EMBROIDERY TECHNOLOGY HAS BEEN DEVELOPED TO FIND A RELIABLE AND CLEVER SOLUTION TO THOSE MANUFACTURERS OF FURNISHING CUSHIONS AND GARDEN CUSHIONS DIFFERENTIATE THEMSELVES IN THE MARKET. THANKS TO THIS SPECIFIC AND ADVANCED SOLUTION MANUFACTURERS ARE ABLE TO REACH THEIR GOAL IN TERMS OF OUTPUT AND PRODUCT QUALITY. THIS KIND OF TECHNOLOGY HAS COMPLETELY CHANGED AND IMPROVED THE PRODUCTION CONCEPT OF FURNISHING CUSHIONS. THANKS TO A VERY RELIABLE PROCESS, THE MACHINE IS SUITABLE FOR SEWING CUSHIONS IN FOAM AND POLYESTER FIBER. QUANTITY AVAILABLE: 1 Learn More