Search results for: 'rolls ro'

WEAVING MACHINES BENNINGER BEN DIRECT WARPER YEAR 2006 BEAM DIAMETER 1000mm, WIDTH 2200mm V-CREEL – 1024 ENDS, AUTOMATIC CUTTING AT CREEL CHANGE ELECTRICAL STOP MOTION, MECHANICAL TENSIONER MICROPROCESSOR CONTROL SUCKER MOENUS SIZING MACHINE YEAR 2006 SIZING MACHINE SUCKER MOENUS Z 14, WIDTH 3400mm 1000mm FLANG DIAMETER, 14 DRYING CYLINDERS 2 SOW BOXES, 2 DIP AND 2 NIP, 24 WARP BEAMS CREEL, FULLY AUTOMATIC PLC CONTROL SIZE MIXING COOLER, 1200 LITERS SIZE STORAGE VESSEL, 1200 LITERS STAUBLI DELTA AUTO DRAWING IN MACHINE YEAR 2006 AUTO DRAWING IN MACHINE, STAUBLI DELTA 110 3400mm, YARN MODULE (HM5), HEALD MODULE (HM2) REED MODULE (HM6), DROP WIRE MODULE (HM3) AND CONTROL MODULE JAYTEX WARP TYING MACHINE YEAR 2005 WARP TYEING MACHINE JAYTEX TROLLEY WITH TRANSFORMER WITH 2 NOS. TYING FRAMES SETIA KIJJI REED CLEANING MACHINE YEAR 2006 SETIA KIJJI – ULTRA SONIC CLEANING MACHINE REED CLEANER CONSISTS OF RINSING UNIT ULTRASONIC UNIT DRYING UNIT, SEMI AUTOMATIC PROCESS USING PLC. (18 UNITS) TSUDAKOMA AIRJET LOOM ZAX 9100 YEAR 2006 3E+06 EACH – 16 SHAFTS AIRJET LOOM TSUDAKOMA ZAX 9100, 3400mm, STAUBLI ELECTRONIC DOBBY 16 SHAFTS, 2/4 WEFT INSERTION, CRANK BEAT UP, LENO SELVEDGE ELECTRONIC LET OFF, ELECTRONIC TAKE UP, 1.5 BEAMS, 1.5 CLOTH ROLLS (48 UNITS) TSUDAKOMA AIRJET LOOM ZAX 9100 YEAR 2006 3E+06 – 10 SHAFTS AIRJET LOOM TSUDAKOMA ZAX 9100, 3400mm, STAUBLI CAM MOTION 10 SHAFTS, 2/4 WEFT INSERTION, CRANK BEAT UP, LENO SELVEDGE ELECTRONIC LET OFF, ELECTRONIC TAKE UP, 1.5 BEAMS, 1.5 CLOTH ROLLS (24 UNITS) TSUDAKOMA AIRJET LOOM ZAX 9100 YEAR 2006 2E+06 – 6 SHAFTS AIRJET LOOM TSUDAKOMA ZAX 9100, 3400mm, STAUBLI CAM MOTION 6 SHAFTS, 2/4 WEFT INSERTION, CRANK BEAT UP, LENO SELVEDGE ELECTRONIC LET OFF, ELECTRONIC TAKE UP, 1.5 BEAMS, 1.5 CLOTH ROLLS (2 UNITS) GREY INSPECTION MACHINE YEAR 2006 INSPECTION TABLE IS LAMINATED, PUSH BUTTON CONTROLS ARE GIVEN ON THE DRIVE BOX ON THE RIGHT HAND SIDE, CLOTH CAN RUN IN FORWARD AS WELL AS IN REVERSE DIRECTION FABRIC RUNS FACE IN/FACE OUT SPECIAL JOGGING OR INCHING DEVICE FABRIC FOLDING MACHINE YEAR 2006 SWINGING MOTION IS MINIMIZED TO ENSURE HIGH MACHINE CAPACITY AND INCREASE OUTPUT FOLDING BLADES ARE MOUNTED ON A CARRIAGE WHICH HAS A TO AND FRO MOVEMENT ACHIEVED BY SPECIAL STEEL ROLLER CHAIRS BALE PRESS YEAR 2001 BATH BEI HYDRAULIC BALE PRESS MACHINE FABRIC PROCESSING SINGEING MACHINE YAMUNA SINGEING MACHINE WIDER WIDTH – YEAR 2006 (2 UNITS) HYDRAULIC JIGGER KUSTER CALICO YEAR 2006 3E+06 VERTICAL DRYING RANGE YEAR 2006 CONTINUOUS DYEING RANGE – KUSTER CALICO KUSTER CALICO COLD PAD BATCH YEAR 2006 HARISH STENTER – SUPRA 5 DLXI ALMAC FINISH INSPECTION MACHINE YEAR 2006 SHRI NARAYAN COTEX FINISH PLAITING MACHINE YEAR 2006 Learn More

YY-1792 ROLL WINDING MACHINE (AUTOMAT FOR FILM AND PAPER), WIDTH 1.200mm, YEAR 2006 FILM THICKNESS: FROM 5 MICRONS TO 4 X 100 MICRONS MINIMUM WINDING WIDTH: 600mm / 23.3 IN MAXIMUM WINDING WIDTH: 1200mm / 47,2 IN MAXIMUM FILM SPEED: 220 M/MIN (720 FT/MIN) MAXIMUM ROLL CHANGES: 16/MIN MAXIMUM ROLL DIAMETER: 250mm / 9.8 IN CORES: WITH OR WITHOUT CORES PAPER CORE DIAMETER: FROM 38mm (1.5 IN) NUMBER OF LANES: 1 PERFORMANCE: MAXIMUM FILM SPEED: 220 M/MIN (720 FT/MIN) MAXIMUM ROLL CHANGES: 16/MIN QUANTITY: 1 Learn More

REFERENCE NUMBER: J-2640
DYEING AND FINISHING PLANT FOR SALE

ITEM 001
THIES SAMPLE DYEING MACHINE
MODEL: MINISOFT SAMPLE
CAPACITY: 50 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 002
THIES DYEING MACHINE
MODEL ECOSOFT PLUS
3 PORT SPLIT/SPLIT
CAPACITY: 900 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 003
THIES DYEING MACHINE
MODEL: ECOSOFT PLUS
2 PORT SPLIT/SPLIT
CAPACITY: 600 KGS
YEAR: 1999
MICROPROCESSOR CONTROL
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 004
THIES DYEING MACHINE
MODEL ECOSOFT PLUS
1 PORT SPLIT/SPLIT
CAPACITY: 300 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: A460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 005
GASTON COUNTY DYEING MACHINE
MODEL: AQUAFLOW
2 PORT
CAPACITY; 250 KGS
YEAR: 1987
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING AND UNLOADING REEL
QUANTITY: 1

ITEM 006
THIES DYEING MACHINE
MODEL: SOFT TRD
2 TUBE
CAPACITY: 700 KGS
YEAR: 1999
MICROPROCESSOR CONTROLLED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
SINGLE ADD TANK WITH MIXER
HEAT EXCHANGER
ALL PUMPS AND MOTORS
LOADING REEL AND FABRIC EXIT PLAITOR
QUANTITY: 1

ITEM 007 (also our J-2647)
LAFER OPEN WIDTH COMPACTOR MACHINE
MODEL: KSA 500 2400/2200
YEAR: 1998
LAFER TEXEN CONTROLS
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION BAR ENTRY TO LATTICE ROLL GUIDER
• OPERATOR’S PLATFORM
• PUP TENTER WITH KNIT ENTRY, VERTICAL PIN CHAIN, WITH PLATE GUIDES, RAIL OPENING, PINNING BRUSHES, PINS ONLY, WITH SUPPORT SECTION FOR THE FABRIC IN THE CENTER, AT 10’ THERE IS A STEAMING SECTION, TOTAL LENGTH OF THE TENTER IS 30’, WITH AUTOMATIC LUBRICATION FOR THE CHAIN
• KSA 500 COMPACTOR BENCH WITH TEXEN CONTROLS
• TENSIONLESS FABRIC CONVEYOR
• PLAITOR AND FABRIC SCRAY WITH OPTICAL LOAD SENSOR
• INLINE INSPECTION BATCHER MACHINE, WITHH A BACK LIGHTED BOARD, MANUAL CUT
• SCALE TO WEIGHT THE FABRIC
QUANTITY: 1

ITEM 008 (also our J-2648)
SANTEX TUBULAR 4-ROLL EXTRACTION PAD
MODEL: SANTASTRETCH PLUS 140
YEAR: 1998
COMPOSED OF TURNTABLE, DETWISTER, TUBULAR 4-ROLL PAD WITH WET SPREADERS, PLAITOR
WITH ADDITION TANKS FOR SOFTENER
REEL FABRIC PLAITOR EXIT
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

ITEM 009
SANTEX CONVEYOR DRYER FOR OPEN WIDTH AND TUBULAR FABRIC
MODEL: SANTASHRINK 4/5240
YEAR: 1998
SANTEX CONTROLS
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION BAR ENTRY TO LATTICE ROLL GUIDER TO
• (2) SANTEX 2-ROLL PADS, RUBBER OVER RUBBER, 102” WIDE x 12” DIAMETER, STAINLESS STEEL PAN, 10-TON PAD, SWING-AWAY PAN, TENSION BAR WITH 2 STAINLESS STEEL MIXING TANKS, 75 GALLONS EACH
• DRIVEN SCROLL ROLLS WITH EDGE GUIDE CONTROL, WIDTH 95”
• OPERATOR’S PLATFORM
• PUP TENTER WITH KNIT ENTRY 45°, YEAR 1998, VERTICAL PIN CHAIN, 30’ LONG WITH TANDEMATIC PLATE GUIDES, RAIL GUIDES, PINNING BRUSHES, GUIDE SUPPORT FOR THE FABRIC, FABRIC CONVEYOR TO ENTER BOTH TUBULAR OR OPEN WIDTH FABRIC TO
• CONVEYOR DRYER 100” WIDE, 5 ZONES, 3-PASS WITH MAXON BURNERS, 5 CIRCULATING FANS TO CONVEYOR BELT TO PLAITOR
• ALL MOTORS AND SANTEX CONTROLS AND MONITORS
QUANTITY: 1

ITEM 010
SANTEX AG TUBULAR COMPACTOR MACHINE
MODEL: SANTASPREAD 140
YEAR: 1998
SANTEX CONTROLS
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSIONS BAR ENTRY
• OPERATOR’S PLATFORM
• TENSION DEVICE
• DRIVEN SPREADER BARS
• STEAMING DEVICE
• TUBULAR COMPACTING BENCH
• FELT BLANKET ONTO THE CONVEYOR BELT
• PRECISION PLAITOR
• TABELTOP ELECTRONIC SCALE
QUANTITY: 1

ITEM 011
COMET NAPPER
MODEL: PEGSO-X4
YEAR: 1998
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
24 ROLLS WITH TURNING BARS FOR TUBULAR 90” WIDE
XYCOM CONTROLS
12-BAG COLLECTION SYSTEM AND PLAITOR
YEAR: 1996
QUANTITY: 1

ITEM 012
STENTEX TENTER FRAME
MODEL: STENTOTHERM 3300
YEAR: 1999
STENTEX CONTROLS
VOLTAGE: 480 VOLTS, 3-PHASE, 60 Hz
COMPOSED OF:
• TENSION ENTRY TO TEXT-STAR TYPE GUIDER TO 2 ROLL PAD
• ADDITION TANK TOP SCRAY PAD TO TEXT-STAR TYPE GUIDER
• TWO ROLL PAD R/R 10 TON
• OPERATOR’S PLATFORM
• WORKING WIDTH 1800mm
• HORIZONTAL PIN CHAIN, KNIT ENTRY
• TANDEMATIC SPLITLEVEL DECURLERS
• OVERFEED
• PINNING BRUSHES
• STEAM BOX
• RAIL GUIDERS, 20 FEET ENTRY, 8 ZONES
• 80 FEET HOUSING
• SCREEN MONITORS
• GAS FIRED, MAXON OVEPAK 408 BURNERS
• HONEYWELL CONTROLS
• 3 FEET COOLING ZONE
• 2 COOLING CANS, SELVEDGE TRIMMERS
• PLIATOR, SCRAY
• ZONE IN LINE INSPECTION BATCHER
QUANTITY: 1

ITEM 013
ZIMMER ROTARY SCREEN PRINTING MACHINE
MODEL: R92-S153
YEAR: 1993
COMPOSED OF:
• TENSION BAR SKY ENTRY
• SCRAY
• CORINO BRUSH
• CORINO PRINT GUIDER
• ZIMMER PRINTER, 8 COLOR, 86” BLANEKT
• PRINT CONVEYOR DRYER, 30’ LONG, 3-ZONE, GAS FIRED
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

ITEM 014
SAFETY SWITCH BULLET NOSE SLITTER
MODEL: CUTTING
WITH REEL FABRIC PLIATOR
VOLTAGE: 460 VOLTS, 3-PHASE, 60 Hz
QUANTITY: 1

Learn More

TT-2113 KROENERT TYPE PAK 600 WAXER / LAMINATOR / COATER, WORKING WIDTH 500 TO 1050mm ITEM 001 KROENERT TYPE PAK 600 WAXER / LAMINATOR / COATER IN 1980 STARTED PRODUCTION TEST POSSIBLE – IMMEDIATELY FREE FOR SALE ITEM 002 STAMPING AND EMBOSSING MACHINE HEIDEMANN ITEM 003 WAX-LAMINATOR KROENERT-PACK 850 THE MACHINE CAN BE DISMANTLED AS FROM NOW. Learn More

REFERENCE NUMBER: V-0046 AUTOMATIC ROLL SHRINK PACKING MACHINE MODEL ARPM-240I QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-5244 (1313JTBVXX12) L TOYOTA JAT610 AIR JET LOOMS YEAR 1998 WIDTH 1900mm-2800mm TOYOTA JAT610 AIR JET LOOMS, YEAR 1998 (60 LOOMS) X WIDTH 1900mm (12 LOOMS) X WIDTH 2800mm RUNNING CONDITION YEAR 1999 1 INVERTER FOR 36 LOOMS (2 INVERTERS FOR ALL 72 LOOMS) QUANTITY AVAILABLE: 27 LOOMS Learn More

TT-4228 KUSTERS THERMOBONDING CALENDER, WORKING WIDTH 3200mm, YEAR 1985 THERMOBONDING CALENDER BRAND: KUSTERS 3 ROLLS YEAR: 1985 QUANTITY: 1 Learn More

TT-1265 DUSENBERY 825, WIDTH 2600mm, YEAR 1984 OTHER DETAILS: PERFORED STATION BURCKHARDT INSTALLED + TOTALLY NEW STATION NOT INSTALLED FOR EACH LINE SPARE PARTS AS: BRUSH ROLLS, NEEDLE RINGS, ETC 4 PCS. ROUND-KNIVES ARE ON EACH MACHINE APPROX. 55 KW INSTALLED AND ABSORBED POWER 40 KW ON EACH OF THE TWO MACHINES. QUANTITY: 2 Learn More

J-3638 POCKET SPRING ROLL PACKING MACHINE CAPACITY: 14 ROLLS PER HOUR MAXIMUM ROLL DIAMETER: 800mm AUTOMATIC FEEDING SYSTEM CENTERING UNIT ON AUTOMATIC FEEDING SYSTEM COUNTER FOR NUMBER OF PRODUCTS TO BE WRAPPED QUANTITY: 1 Learn More

TT-7342 STARVIEW RP 28-2 ROLLER DIE CUTTER, YEAR 2021, WIDTH 29 INCHES 1. LIKE NEW 2. TYPE: USED FLATBED ROLLER DIE CUTTERS 3. BRAND: STARVIEW PACKAGING 4. MODEL: RP28-2 QUANTITY: 1 Learn More