Search results for: 'HIGH PRE'

TT-2153 SIEMENS SGT-800 GAS TURBINE, 54 MW, 11 KV, 50 Hz AND 1500 RPM, FUEL NATURAL GAS, FREQUENCY 50/60 Hz GROSS EFFICIENCY 38.86.0% HEAT RATE9, 256 KJ/KWH UNUSED CONDITION: EXCELLENT (NEW SURPLUS) TURBINES STORED TO SIEMENS RECOMMENDATION. NOTE: THIS IS A PACKAGE DEAL AND REQUIRES BUYER TO PURCHASE ALL 3 UNITS. POI AND POF REQUIRED UPFRONT. QUANTITY: 3 Learn More

YY-2223 BRIQUETTING MACHINES ASK FOR MORE DETAILS! Learn More

YY-2208 HUMAN CREMATION MACHINE, LIGHT DIESEL FUEL, GAS, NATURAL GAS, LIQUEFIED GAS DETAILS: 1. INCORPORATES EFFICIENT HEAT EXCHANGER AND SPECIAL AIR PATH STRUCTURE, MAKE FULL USE OF WASTE HEAT COMBUSTION FUEL GAS, IMPROVING HEAT UTILIZATION RATE, GOOD ENVIRONMENTAL PROTECTION INDEX, SAVES FUEL AND SHORTENS CREMATION TIME. 2. NEW REFRACTORY MATERIALS (EXCLUSIVE FORMULA) THAT ARE RESISTANT TO HIGH TEMPERATURE WITH LOW SPECIFIC HEAT. GREATLY EXTEND THE SERVICE LIFE. 3. SPECIAL CASTING MATERIAL, HIGH TEMPERATURE RESISTANCE, LONG SERVICE LIFE; SHORTENS THE COOLING CYCLE. THE BRICK STRUCTURE ON BOTH SIDES OF THE ASH PICKING FURNACE DOOR WILL NOT HAVE CRACKS CAUSED BY DESIGN OR QUALITY PROBLEMS GUARANTEED FOR ONE YEAR. REFRACTORY MATERIALS, THE FURNACE CONTACT ARE WITH FLAME HAS PHOSPHORIC ACID A CHARACTERISTIC COMBINATION BRICK WHICH CAN RESIST RAPID COOLING AND RAPID HEAT, AND THE ARCHED ROOF INCORPORATES HIGH ALUMINUM SINTERED MOLDING BRICK. THE FURNACE BODY IS SURROUNDED BY ALUMINUM SILICATE WOOL WITH GOOD HEAT INSULATION AND HEAT PRESERVATION PERFORMANCE. THE THICKNESS IS 180mm. 4. ALL OPERATING SYSTEMS OF THE EQUIPMENT HAVE THREE SETS OF OPERATION FUNCTIONS, NAMELY AUTOMATIC, SEMI-AUTOMATIC AND MANUAL, WHICH CAN BE SWITCH BETWEEN THEM WITHOUT INTERFERENCE. AUTOMATIC CONTROL, TELECOMMUNICATION OPERATION AND ANIMATION DISPLAY. KEEPING THE OPERATOR AWAY FROM THE CREMATION SITE AND PROTECTING THE OPERATOR. AT THE SAME TIME EQUIPPED WITH A STANDBY OPERATING SYSTEM. LOW NOISE MOTOR EQUIPMENT, THERMOCOUPLE RESISTANCE TO HIGH TEMPERATURE. ALL ELECTRICAL CABINETS OF THE EQUIPMENT ARE EXTERNAL. 5. THE OIL SUPPLY SYSTEM INCORPORATES AUTOMATIC CONTROL AND MANUAL CONTROL, AND INCORPORATES OIL PROTECTION TECHNOLOGY, WHICH CAN EFFECTIVELY PREVENT FUEL OIL FROM RUNNING, BUBBLING, LEAKING AND CAUSING FURNACE EXPLOSION ACCIDENTS INCLUDING ANTI-LEAKAGE TECHNOLOGY TO BETTER PROTECT THE PERSONAL SAFETY OF OPERATORS. 6. THE BLOWER, THE INDUCED DRAFT FAN, THE FURNACE DOOR MOTOR, THE BODY CART MOTOR, THE PREPARATORY DOOR MOTOR AND THE FLUE GATE MOTOR ARE ALL INSTALLED WITH AN INTEGRATED DEVICE FOR OVER-CURRENT AND SHORT-CIRCUIT PROTECTION. 7. SPECIAL DIESEL METERING DEVICE, ACCURATE METERING. QUANTITY: 1 Learn More

J-4121 HIGH-SPEED CROSS LAPPER, INPUT WIDTH 2900mm, OUTPUT WIDTH 4500mm, 80 METERS/MINUTE APPLICATION: USED TO FOLD EVENLY AND LAP THE FIBER WEBS INTO CERTAIN WIDTH AND THICKNESS INPUT WIDTH: 2900mm OUTPUT WIDTH: 4500mm SPEED: 80 METERS PER MINUTE QUANTITY: 1 Learn More

AA-1189 CONTAINER LOADING CRANE TECHNICAL PARAMETERS: TYPICAL QUAYSIDE CRANE 1. A: GANTRY SPAN: 15000 TO 35000mm 2. C: BACKREACH: 0 TO 25000mm 3. E: CLEARANCE UNDER SILL BEAM: 12000 TO 18000mm 4. G: TRAVEL WHEEL GAUGE: 18200mm 5. H: BUFFER TO BUFFER: 27000mm 6. WHEEL SPACING: 1000 TO 2000mm 7. WHEELS PER CORNER (DEPENDS ON REQUIRED WHEEL LOADS): 6/12 – SEASIDE 8. WHEELS PER CORNER (DEPENDS ON REQUIRED WHEEL LOADS): 6/12 – LANDSIDE 9. MAX. WIDTH TROLLEY AND MAIN BEAM/BOOM: 7600mm Learn More

REFERENCE NUMBER: A-2471 INDUSTRIAL ELECTROSPINNING MACHINE A MASS PRODUCTION MACHINE OF ELECTROSPINNING. ALUMINUM FRAME STRUCTURE MAKES IT POSSIBLE FOR EXTENDING DIFFERENT FUNCTIONS. THE SPINNERET USED IS MULTI-NEEDLE ARRAYS, FROM 64 TO 384 NEEDLES ARE EQUIPPED. THE LENGTH AND WIDTH CAN BE MADE ACCORDING TO CUSTOMER'S REQUIREMENT. ROLL TO ROLL COLLECTOR AND CONTINUOUS COLLECTOR CAN BE USED BASED ON THE THICKNESS OF REQUIRED FIBER SHEET. FOR SOLUTIONS, A MULTI-CHANNEL PUMP WILL BE SUPPLIED FOR LONG TIME PRODUCTION OR NONE-STOP PRODUCTION. FEATURES: － EQUIPPED WITH BOTH POSITIVE & NEGATIVE HIGH VOLTAGE SUPPLY DEVICES － EQUIPPED WITH UNWINDING & WINDING MACHINES － CONTINUOUS ELECTROSPINNING & WINDING － ALUMINUM ALLOY FRAME STRUCTURE, MULTI-FUNCTIONS EXPANSIBLE － MULTI-NEEDLES IN ARRAYS. 16 NEEDLES X N ROWS, UP TO 384 NEEDLES － SPINNERET MOVING MACHINERY ENSURES EVEN FIBER SHEET － ONLINE AUTO-CLEAN DEVICE FOR NEEDLES － THICKNESS OF THE FIBER SHEET IS CONTROLLABLE － CE & FCC CERTIFICATE SPINNERET STANDARD：16 NEEDLES X 8 GROUPS =128 NEEDLES (THE NUMBER OF NEEDLES CAN BE ADJUSTED FREELY ACCORDING TO THE REQUIREMENTS OF USE） X-Y-Z MOTION SYSTEM － THE NOZZLE CAN BE MOVED UP AND DOWN IN THE Z DIRECTION THROUGH THE TOUCH SCREEN CONTROL TO DETERMINE THE APPROPRIATE SPINNING DISTANCE. － THE NOZZLE CAN MOVE BACK AND FORTH ALONG THE YAXIS DIRECTION OF THE TANGENT DIRECTION OF THE RECEIVING FILM TO PREPARE A UNIFORM FIBER FILM. － THE NOZZLE AUTOMATIC ONLINE CLEANING DEVICE SCANS ALONG THE X-AXIS DIRECTION. COLLECTOR － STAINLESS STEEL PLATE / MESH SERVES AS A CARRIER FOR THE FIBER MEMBRANE SUBSTRATE. － CONNECTED WITH NEGATIVE HIGH VOLTAGE. － RECEIVER BOARD WIDTH: 500 mm － SPINNING DISTANCE: 80 TO 300 mm ADJUSTABLE WINDER AND UNWINDER － AUTOMATICALLY CALCULATE THE ROLL DIAMETER OF THE LOADED MATERIAL AND CONTROL THE TENSION BETWEEN THE UNWINDING AND SPINNING SECTIONS. － CONSTANT FEEDING SPEED. THE FEEDING SPEED RANGE IS 0 TO 5000 mm / min. － ONLINE HOT PRESSING FUNCTION MODULE. AFTER THE SPINNING IS COMPLETED, BEFORE THE WINDING, A TEMPERATURE-CONTROLLED HOT PRESSING DEVICE (ROOM TEMPERATURE TO 60 ° C) IS USED FOR HOT PRESSING. (OPTIONAL THIRD LAYER MATERIAL STICKING AND REWINDING DEVICE). － CAN BE OPERATED BY TOUCH SCREEN. － DO NOT USE METAL FILM AS THE RECEIVING CARRIER. SYRINGE PUMP － 200ML X 4N CHANNEL － FLOW RATE: 0.1ML / H TO 1280 ML / H － SPECIALLY DESIGNED FOR ELECTRO-SPINNING AND RESISTANT TO HIGH VOLTAGE. HIGH VOLTAGE DEVICE －0 TO 50KV, DIGITAL DISPLAY －-50KV ~ 0 KV, DIGITAL DISPLAY －OUTPUT CURRENT: <1 MA －CONTINUOUSLY ADJUSTABLE CONTROL SYSTEM －PLC CONTROL SYSTEM, 7-INCH TOUCH SCREEN. －CONTROL THE MOVEMENT OF THE NOZZLE. －CONTROL THE NOZZLE TO MOVE UP AND DOWN. －YOU CAN SET THE MOVEMENT TIME, STROKE AND SPEED OF THE NOZZLE. －CONTROL THE FREQUENCY OF NOZZLE CLEANING. －SPINNING PROCESS PARAMETER RECORDS. ENVIRONMENTAL CONTROL SYSTEM －PROVIDE INTERFACE TO LET IN DRY AMBIENT HUMIDITY AIR. －AN EXTERNAL DEHUMIDIFIER CAN BE USED TO CONTROL THE AMBIENT HUMIDITY. THE EXTERNAL DEHUMIDIFIER NEEDS TO BE SELECTED ACCORDING TO THE SIZE OF THE WORKSHOP. THIS EQUIPMENT DOES NOT INCLUDE THIS DEHUMIDIFIER. EXHAUST SYSTEM －BOTTOM UP, AND FOUR FANS ARE PUMPED AT THE SAME TIME. －THE DISCHARGE VOLUME OF A SINGLE UNIT IS 5 TO 150 M3 / H, AND THE RATE IS ADJUSTABLE. THE COMBINED DISCHARGE VOLUME OF THE TWO EXHAUST FANS IS 10 TO 300M3 / H. THE EXTRACTOR IS DRAWN FROM THE MIDDLE. IN THIS WAY, THE HIGH-SPEED AIR VENTILATION MINIMIZES THE RELATIVE DISTURBANCE TO THE SPINNING. THE EXHAUST FAN IS A SILENT EXHAUST FAN. SAFETY －AUTOMATIC POWER-OFF DEVICE FOR OPENING THE DOOR. －RESIDUAL STATIC ELECTRICITY REMOVAL DEVICE. －EMERGENCY STOP SWITCH. －GROUND AT MULTIPLE POINTS. －ALARM DEVICE AFTER THE CONTROL PARAMETERS EXCEED THE LIMIT. CHAMBER －THE CHAMBER IS MADE OF ALUMINUM ALLOY FRAME. －THE FRONT AND SIDE WINDOWS OF THE CABINET ARE MADE OF TEMPERED GLASS. －MULTI-POINT TEMPERATURE AND HUMIDITY COLLECTION AND DISPLAY. －THE PROCESS CAN BE OBSERVED WITH THE NAKED EYE. －AIR INLET: HOT AND DRY AIR CAN BE INTRODUCED TO QUICKLY ADJUST THE HUMIDITY INSIDE THE CHAMBER. POWER SOURCE －220 VOLTS AND 50/60 Hz －TOTAL POWER: 10KW NUMBER OF NEEDLES: 128 NEEDLES (THE NUMBER OF NEEDLES CAN BE ARBITRARILY REDUCED ACCORDING TO THE SOLVENT USAGE) FLOW RATE OF EACH NEEDLE: (~ 3ML ± 50%) / HOUR TOTAL FLOW OF THE WHOLE MACHINE: ABOUT (400ML ± 50%) / HOUR SOLUTION CONCENTRATION: 10 TO 20% 8 HOURS SOLUTION PROCESSING CAPACITY: ABOUT (3L ± 50%) / 8 HOURS SOLID CONTENT (WEIGHT OF FIBER PRODUCED): (300G ± 50%) / 8 HOURS ACCORDING TO THE APPROXIMATE PRODUCTION OF FIBER MATERIAL WITH A GRAM WEIGHT OF 2GSM. WINDING AND UNWINDING SPEED: 50M / H MATERIAL WIDTH: 0.5 METERS FABRIC AREA PRODUCED PER HOUR: 25 SQUARE METERS FABRIC AREA PRODUCED IN 8 HOURS: 200 SQUARE METERS FABRIC AREA PRODUCED IN 24 HOURS: 600 SQUARE METERS BASED ON THE PRODUCTION OF FIBER MATERIAL WITH A GRAMMAGE OF 0.02G / ㎡, APPROXIMATELY: WINDING AND UNWINDING SPEED: 5000M / H MATERIAL WIDTH: 0.5 METERS FABRIC AREA PRODUCED PER HOUR: 2500 SQUARE METERS FABRIC AREA PRODUCED IN 8 HOURS: 20,000 SQUARE METERS FABRIC AREA PRODUCED IN 24 HOURS: ABOUT 60,000 SQUARE METERS Learn More

REFERENCE NUMBER: T-6550

MEDICAL PROTECTIVE CLOTHING BLOOD SYNTHETIC PENETRABILITY TESTER

 

TECHNICAL SPECIFICATIONS AND CONFIGURATION:

1. THE INSTRUMENT ADOPTS AN AIR SOURCE THAT CAN PROVIDE (0.5 ~ 30±0.1) KPA PRESSURE TO CONTINUOUSLY PRESSURIZED THE SAMPLE, WHICH IS NOT RESTRICTED BY THE SPACE OF THE TEST SITE;

2. THE AIR PRESSURE RANGE CAN BE ADJUSTED FREELY, AND THE ADJUSTMENT RANGE (0.5 ~ 30) KPA;

3. COLOR TOUCH SCREEN DISPLAY AND OPERATION;

4. THE SAMPLE CLAMPING PAD IS PROCESSED WITH IMPORTED SPECIAL ALUMINUM PROFILES, WHICH IS LIGHT IN MATERIAL, CLEAN IN SURFACE AND NEVER RUSTS.

5. THE INSTRUMENT ADOPTS IMPORTED SPECIAL ALUMINUM WIRE DRAWING PANEL, EQUIPPED WITH METAL KEYS, SENSITIVE OPERATION, NOT EASY TO DAMAGE;

6. CLAMPING DEVICE FOR INSTRUMENT SAMPLES, EQUIPPED WITH LOCKING PROTECTION, TO PREVENT THE SYNTHETIC BLOOD FROM SPLASHING AROUND;

7. CLAMPING FORCE IS ACCURATE AND RELIABLE;

8. THE TEST TANK IS EQUIPPED WITH A SPECIAL PLACEMENT DEVICE, WHICH IS CONVENIENT FOR CUSTOMERS TO OPERATE;

9. THE TEST TANK IS PROCESSED WITH SPECIAL 316 STAINLESS STEEL, AND THE TOP IS EQUIPPED WITH A SPECIAL COVER FOR HIGH TRANSPARENT PROTECTION;

10. THE WASHER BELOW THE SAMPLE IS MADE OF HIGH-QUALITY PTFE MATERIAL AFTER SPECIAL PROCESSING;

11. SQUARE METAL BLOCK NET: OPEN SPACE ≥50°%; BENDING ≤5mm AT 30KPA;

12. INSTRUMENT TIME CONTROL ACCURACY ≤01 SECONDS;

13. THE SHELL OF THE INSTRUMENT IS MADE OF HIGH-QUALITY METAL BAKING PAINT, WHICH IS BEAUTIFUL AND GENEROUS.

14. EQUIPPED WITH PRINTER INTERFACE, CONNECTED TO THE PRINTER CAN DIRECTLY PRINT DATA REPORTS.

 

TECHNICAL PARAMETERS:

1. SAMPLE SIZE: 75mm X 75mm

2. TEST AREA: 28.26 SQUARE CENTIMETERS

3. AIR PRESSURE ADJUSTMENT RANGE (0.5 ~ 30) KPA

4. EXTERNAL SIZE: 500mm X 500mm X 500mm (L X W X H)

5. WEIGHT OF THE INSTRUMENT: 40 KG

6. POWER SUPPLY: AC220V, 50HZ,SCOPE OF SUPPLY: 1. ONE MAIN MACHINE; 2. TWO PTFE GASKETS; 3. TWO ORDINARY WASHERS; 4. ONE METAL BLOCKING NET; 5. A SET OF SPECIAL LOCKING TOOLS; 6. ONE HIGH-QUALITY SILENT AIR PUMP, [NOTE: SAFETY PRODUCTION LICENSE IS NOT INCLUDED]. 7. EQUIPPED WITH PRINTER INTERFACE; 8. ONE SAMPLE TEMPLATE; 9. ONE PRODUCT CERTIFICATE; 10. ONE COPY OF PRODUCT OPERATION MANUAL.

 

OPERATION INSTRUCTION:

INSERT THE AIR PUMP OUTPUT PIPE INTO THE OIL AND WATER SEPARATOR OF THE INSTRUMENT AS REQUIRED (PRESSURE 0.1-0.3MPA).

AFTER SWITCHING ON THE POWER, THE STARTUP INTERFACE (NAME OF THE DEVICE) IS DISPLAYED.

PRESS THE "ENTER" BUTTON TO ENTER THE TEST INTERFACE, AS SHOWN IN THE FOLLOWING FIGURE:

CLICK "SETTING” BUTTON, GET INTO PARAMETER SETTING SCREEN, AS BELOW THIS SCREEN CAN SET THE SYSTEM TIME, DATE AND TESTING TIME, AFTER SETTING, CLICK "SAVE” BUTTON TO KEEP THE SETTING DATA. (NOTE: IT REQUIRES 5 MINUTES IN THE STANDARD)

 

QUANTITY: 1

Learn More

YARN SINGEING MACHINE
MODEL Q488
PRODUCT FEATURES:
FREQUENCY CONVERSION SPEED REGULATION DEVICE, CONVENIENT ADJUSTM
ENT WINDING LINEAR SPEED IS HIGH
TAPER TYPE CONE OR PLAIN CONE TYPE;
HIGH QUALITY OF METALLIC GROOVED DRUM THROUGH DYNAMICALLY BALANCED, GROOVED DRUM AXLE WITH HIGH
ACCURACY OF MANUFACTURE HAS PREMIX TYPE AIR/GAS MIXED BOX AND NEW TYPE BURNER, FLAME STABILIZATION, HIGH BURNING TEMPERATURE, EVEN
SINGEING, LOW GAS CONSUMPTION;
AUTOMATIC STOP MOTION
DUST BLOW-EXHAUST APPARATUS AND DUST REMOVAL BY VENTILATION DEVICE;
PLC CONTROL SYSTEM;

MAIN TECHNICAL PARAMETER:
EACH MACHINE HAS 72 SPINDLES (DOUBLE-FACED)
SPINDLE DISTANCE IS 288mm GAUGE, CAN BE PACKAGE, TAPER TUBE, PARALLEL TUBE;
TUBE SIZE, PAPER TUBE IS 3° 30
PLASTIC TUBE IS 5 ° 57′, WOODEN TUBE ISΦ 25.4 × 147.5 × Φ 8.4
GROOVE DRUM MATERIAL IS ALUMINIUM ALLOY  
WINDING SPEED 200 TO 750mm, 200 TO 8200mm
MOTOR POWER 14.14KW
DIMENSIONS (LWH) 13117 × 1850 × 2840mm
MACHINE WEIGHT: 4550 KGS

QUANTITY: 1

Learn More

C-3980 KRAFT PAPER MAKING MACHINE WITH GAS BOILER, CAPACITY 3 TO 5 T/D, NET PAPER WIDTH 1200mm

KRAFT PAPER MAKING MACHINE
WITH GAS BOILER
CAPACITY: 3 TO 5 T/D KRAFT PAPER MACHINE
1092 KRAFT CORRUGATED PAPER MACHINE
WITH RECYCLE PAPER AS RAW MATERIAL
TECHNICAL PARAMETER:
OUTPUT: KRAFT PAPER, CORRUGATED PAPER
WEIGHT: 60 TO 180G/M2
NET PAPER WIDTH: 1200mm

QUANTITY: 1

Learn More

REFERENCE NUMBER: M-0809 HIGH POLYMER MATTRESS 25 TO 200mm TALL (POLYMAT) QUANTITY AVAILABLE: 1

Learn More