Search results for: 'equipment''

YY-2208 HUMAN CREMATION MACHINE, LIGHT DIESEL FUEL, GAS, NATURAL GAS, LIQUEFIED GAS DETAILS: 1. INCORPORATES EFFICIENT HEAT EXCHANGER AND SPECIAL AIR PATH STRUCTURE, MAKE FULL USE OF WASTE HEAT COMBUSTION FUEL GAS, IMPROVING HEAT UTILIZATION RATE, GOOD ENVIRONMENTAL PROTECTION INDEX, SAVES FUEL AND SHORTENS CREMATION TIME. 2. NEW REFRACTORY MATERIALS (EXCLUSIVE FORMULA) THAT ARE RESISTANT TO HIGH TEMPERATURE WITH LOW SPECIFIC HEAT. GREATLY EXTEND THE SERVICE LIFE. 3. SPECIAL CASTING MATERIAL, HIGH TEMPERATURE RESISTANCE, LONG SERVICE LIFE; SHORTENS THE COOLING CYCLE. THE BRICK STRUCTURE ON BOTH SIDES OF THE ASH PICKING FURNACE DOOR WILL NOT HAVE CRACKS CAUSED BY DESIGN OR QUALITY PROBLEMS GUARANTEED FOR ONE YEAR. REFRACTORY MATERIALS, THE FURNACE CONTACT ARE WITH FLAME HAS PHOSPHORIC ACID A CHARACTERISTIC COMBINATION BRICK WHICH CAN RESIST RAPID COOLING AND RAPID HEAT, AND THE ARCHED ROOF INCORPORATES HIGH ALUMINUM SINTERED MOLDING BRICK. THE FURNACE BODY IS SURROUNDED BY ALUMINUM SILICATE WOOL WITH GOOD HEAT INSULATION AND HEAT PRESERVATION PERFORMANCE. THE THICKNESS IS 180mm. 4. ALL OPERATING SYSTEMS OF THE EQUIPMENT HAVE THREE SETS OF OPERATION FUNCTIONS, NAMELY AUTOMATIC, SEMI-AUTOMATIC AND MANUAL, WHICH CAN BE SWITCH BETWEEN THEM WITHOUT INTERFERENCE. AUTOMATIC CONTROL, TELECOMMUNICATION OPERATION AND ANIMATION DISPLAY. KEEPING THE OPERATOR AWAY FROM THE CREMATION SITE AND PROTECTING THE OPERATOR. AT THE SAME TIME EQUIPPED WITH A STANDBY OPERATING SYSTEM. LOW NOISE MOTOR EQUIPMENT, THERMOCOUPLE RESISTANCE TO HIGH TEMPERATURE. ALL ELECTRICAL CABINETS OF THE EQUIPMENT ARE EXTERNAL. 5. THE OIL SUPPLY SYSTEM INCORPORATES AUTOMATIC CONTROL AND MANUAL CONTROL, AND INCORPORATES OIL PROTECTION TECHNOLOGY, WHICH CAN EFFECTIVELY PREVENT FUEL OIL FROM RUNNING, BUBBLING, LEAKING AND CAUSING FURNACE EXPLOSION ACCIDENTS INCLUDING ANTI-LEAKAGE TECHNOLOGY TO BETTER PROTECT THE PERSONAL SAFETY OF OPERATORS. 6. THE BLOWER, THE INDUCED DRAFT FAN, THE FURNACE DOOR MOTOR, THE BODY CART MOTOR, THE PREPARATORY DOOR MOTOR AND THE FLUE GATE MOTOR ARE ALL INSTALLED WITH AN INTEGRATED DEVICE FOR OVER-CURRENT AND SHORT-CIRCUIT PROTECTION. 7. SPECIAL DIESEL METERING DEVICE, ACCURATE METERING. QUANTITY: 1 Learn More

TT-1040 COMPUTERIZED TENSILE TESTING MACHINE, 150KN COMPUTERIZED TENSILE TESTING MACHINE KEY SPECIFICATION: CAPACITY: KGF 3000, 5000, 10000, 15000 KN 30, 50, 100, 150 UNIT: LOAD N, KN, G, KG, TON, LB DISPLACEMENT: mm, CM, INCH LOAD RESOLUTION: 1/20,000 LOAD ACCURACY: ±1% (±0.5% OPTIONAL) LOAD AMPLIFICATION: X 1, X 2, X 5, X 10 AUTO RANGE TESTING WIDTH (mm): 560 (800 OPTIONAL) CROSSHEAD TRAVEL (mm): 980 (1480 OPTIONAL) TESTING STROKE: CROSSHEAD TRAVEL MINUS UPPER/LOWER GRIPS AND GRIPPING LENGTH TEST SPEED RANGE (mm/MIN): 0.5~500 OR 0.2~200, 0.2~200 OR 0.5~500 MAXIMUM FORCE AT FULL SPEED (KGF): 1000, 2000 MAXIMUM SPEED AT FULL LOAD (mm/MIN): 100, 50 SPEED ACCURACY: ±0.5% SERVO CONTROL DISPLACEMENT RESOLUTION: 0.001 DRIVING METHOD: AC SERVO MOTOR POWER SPECIFICATIONS: 3Ø, 220VAC, 50/60Hz (380/415V OPTIONAL) CONSUMPTION: 3000 KGF 30 KN 5000 KGF 50 KN 10000 KGF 100 KN 15000 KGF 150 KN 2 KVA, 3 KVA, 5 KVA, 10 KVA DIMENSIONS FRAME (mm): 1300 X 600 X 2130 1540 X 600 X 2130 1300 X 600 X 2630 1540 X 600 X 2630 CONTROL BOX (mm) COMPUTER TYPE 1200 X 600 X 740 MICRO-COMPUTER TYPE 660 X 600 X 740 WEIGHT (KG) FRAME 800, CONTROL BOX 100 FRAME 1200, CONTROL BOX 100 STANDARD ACCESSORIES: TENSILE GRIPS X 1 SET, NECESSARY TOOLS X 1 SET, OPERATIONAL MANUAL X 1 COPY, CERTIFICATE OF CALIBRATION X 1 COPY Learn More

T-9752 KARL MAYER CARBON MACHINES BIAXIAL AND MULTIAXIAL PROPERTIES: SINCE ALL FIBERS POINT IN ONE DIRECTION, THE SCRIM CAN BE IDEALLY DRAPED GOOD SOAKABILITY WITH LITTLE RESIN CONSUMPTION CAN BE DRAPED VERY WELL AROUND CURVES AND EDGES EASY TO CUT ELECTRICALLY CONDUCTIVE, INFUSIBLE HIGH STRENGTH AND RIGIDITY DUE TO GRAPHITE-LIKE FIBER STRUCTURE BIOCOMPATIBLE TRANSPARENT TO X-RAYS LOW SPECIFIC WEIGHT IDEAL FOR SURFACE USE (LITTLE FIBER IMPRINTS) IDEAL FOR PROCESSING WITH EPOXY RESIN! TEXTILE SEMI-FINISHED PRODUCTS MADE OF PRE-SPREAD AND PLANE-PARALLEL LAID FIBERS FORM THE GROUP OF UNIDIRECTIONAL FABRICS. THE FIBERS ARE USUALLY LAID AT 0°, MORE RARELY AT 90°. BY LAYING THE UD FABRICS ALONG THE LINES OF FORCE ACTING IN THE COMPONENT, THE LIGHTWEIGHT POTENTIAL OF THE CARBON FIBER IS OPTIMALLY EXPLOITED. UD FABRICS CONSIST OF ONE OR MORE SUPERIMPOSED FIBER LAYERS FIXED WITH AN EPOXY-COMPATIBLE BINDER THREAD. THE SPECIAL SPREADING TECHNIQUE PRODUCES FABRICS WITH HIGH FIBER PARALLELISM, WITHOUT KNOTS AND FIBER TWIST. SPREAD FIBERS ABSORB THE RESIN BETTER, RESULTING IN HIGHEST LAMINATE STRENGTHS. QUANTITY: 3 LINES Learn More

YY-1792 ROLL WINDING MACHINE (AUTOMAT FOR FILM AND PAPER), WIDTH 1.200mm, YEAR 2006 FILM THICKNESS: FROM 5 MICRONS TO 4 X 100 MICRONS MINIMUM WINDING WIDTH: 600mm / 23.3 IN MAXIMUM WINDING WIDTH: 1200mm / 47,2 IN MAXIMUM FILM SPEED: 220 M/MIN (720 FT/MIN) MAXIMUM ROLL CHANGES: 16/MIN MAXIMUM ROLL DIAMETER: 250mm / 9.8 IN CORES: WITH OR WITHOUT CORES PAPER CORE DIAMETER: FROM 38mm (1.5 IN) NUMBER OF LANES: 1 PERFORMANCE: MAXIMUM FILM SPEED: 220 M/MIN (720 FT/MIN) MAXIMUM ROLL CHANGES: 16/MIN QUANTITY: 1 Learn More

YY-1347 PSA OXYGEN GENERATION SYSTEM SCHEME, CAPACITY 50 m3 PER HOUR PURITY: ≥ 93%, FLOW RATE: 50M3 PER H, (PRESSURE: 200 BAR AUTOMATIC FILLING SYSTEM) Learn More

YY-1348 PSA OXYGEN GENERATION SYSTEM SCHEME, FLOW RATE 100 M3 PER HOUR DETAILS: PURITY: ≥ 93%, FLOW RATE: 100 M3 / H, (PRESSURE: 200 BAR AUTOMATIC FILLING SYSTEM) QUANTITY: 1 Learn More

T-7934 MEDICAL SURGICAL LATEX GLOVES INNER PACKING MACHINE A. IT IS MAINLY USED FOR LATEX GLOVE INSIDE PACKING, GLOVE LENGTH FROM 175 TO 190mm CAN BE ADJUSTED, WIDTH FROM 90 TO 110MM CAN BE ADJUSTED, B. SPEED: 20 TO 28 PCS/MIN C. VOLTAGE: 380V, WORKING AIR PRESSURE: 0.6 TO 1.0MP D. TOTAL POWER: 4KW Learn More

T-7764 SOLAR TITAN T-70, 7.1MW ISO, 13,800 VOLTS, 60Hz THIS PACKAGE WAS DELIVERED FULLY ENCLOSED AND SUITABLE FOR OUTDOOR INSTALLATION COMPLETE FIRE SYSTEM, WITH BOTTLES COMPLETE AIR FILTRATION SYSTEM (HUFF AND PUFF SELF-CLEANING) NEUTRAL GROUNDING RESISTOR QUANTITY: 1 Learn More

REFERENCE NUMBER: Y-2073 RAIN TEST CHAMBER WATER SPRAY SIMULATION THIS EQUIPMENT IS APPLICABLE TO THE TEST OF RAINPROOF DUST AND SAND SOAKED WATER OF VARIOUS AUTO PARTS, ELECTRONIC APPLIANCES, AND OTHER INDUSTRIAL ELECTRONIC PRODUCTS. AUTO PARTS INCLUDE THE TEST OF FULL SEALING STABILITY OF THE SYSTEM SUCH AS LAMPS, DOOR LOCKS, ELECTRICAL, INSTRUMENTS, DUST COVERS, ELECTRONIC HOUSEHOLD APPLIANCES, ETC. THE TESTED ITEMS ARE INSTALLED OR PLACE IN THE CENTER OF SEMICIRCLE BENDING TUBES AND BOTTOM AND SWING OF THE SPLASHED SAMPLES. THE AXIS IS IN A HORIZONTAL POSITION, AND THE SAMPLES ROTATES AROUND THE CENTERLINE DURING THE TEST. TECHNICAL PARAMETERS: CHAMBER SIZE: 600mm X 600mm X 600mm (WxDxH) DIAMETER OF SPRAY: ⊄0.4mm SPACING OF SPRAY HOLES: 50mm SPRAY PIPE DIAMETER: 16mm NOZZLE ANGLE ADJUSTABLE: 120 (IPX3) 180(IPX4) RADIUS OF SPRAY RING: R 375mm WATER PRESSURE: ADJUSTABLE WATER FLOW AS REQUIRED FLOW: 1 TO 7L PER MINUTE, FLOW SPEED ADJUSTABLE AIR VELOCITY: 10mm PER SECOND TEST TIME: 0 TO 999 MIN ADJUSTABLE SWING ANGLE AMPLITUDE OF SWING TUBE: ±45˙ ± 60˙ ±180˙ PENDULUM TUBE: IT IS DRIVEN BY SERVO MOTOR, WITH HIGH PRECISION AND ACCURATE TIME AND SWING WATER SUPPLY PIPELINE: PPR PIPE IS USED FOR EQUIPMENT WATER SUPPLY, WHICH IS ARRANGE ACCORDING TO BOX DISTRIBUTION AND CONTROLLED BY EQUIPMENT CONTROL SYSTEM CABINET. HEATING MODE: INCORPORATE STAINLESS STEEL HEATING PIPE, SHALLOW WATER PLATE SURFACE EVAPORATION. SPRAY CYCLE: THE SPRAY CYCLE IN THE BOX IS ADJUSTABLE, AND THE DOOR IS EQUIPPED WITH AN OBSERVATION WINDOW TO OBSERVE THE STATE OF THE SAMPLE IN THE BOX. WINDOW WIPED INSTALLED. QUANTITY: 1 Learn More

REFERENCE NUMBER: P-8845 FULLY AUTOMATIC MASK MACHINE THIS EQUIPMENT IS A FULL-AUTOMATIC ONE-TIME PLANE MASK FORMING MACHINE, WHICH IS USED FOR THE FORMING OF ONE-TIME RECTANGULAR EAR HANGING THREE DRAWER MASKS. ONE MAIN MACHINE IS EQUIPPED WITH TWO EAR BELT SPOT WELDING MACHINES (ONE FOR TWO). THE DRIVING MOTOR IS SERVO MOTOR, SO IT HAS THE ADVANTAGES OF HIGH RELIABILITY, EASY OPERATION, ACCURATE TRANSMISSION, STABLE CONTROL, ADJUSTABLE SPEED, LOW COST AND CONVENIENT MAINTENANCE, ESPECIALLY SUITABLE FOR THE PRODUCTION OF HIGH-QUALITY MASKS. SPECIFICATIONS TEMPERATURE: 10 TO 350, HUMIDITY 5 TO 35%, NO FLAMMABILITY AND NONCORROSIVE GAS VOLTAGE: 220V POWER FREQUENCY: 50Hz PER 60Hz TOTAL POWER OF EQUIPMENT: 8.5KW ULTRASONIC FREQUENCY: 5 TO 20KHz MAX FEEDING WITH OVERALL DIMENSION OF EQUIPMENT: 6100 x 3300 x 1800 MACHINE WEIGHT: 2 TONS PRODUCTION EFFICIENCY: 80 TO 120 TABLETS PER MIN (EACH WORKING STATION 60 PCS PER MIN, AS WE HAVE TWO WORKING STATION). OPERATOR: 1 PERSON QUANTITY: 1 Learn More