Search results for: 'Gas en'

YY-2208 HUMAN CREMATION MACHINE, LIGHT DIESEL FUEL, GAS, NATURAL GAS, LIQUEFIED GAS DETAILS: 1. INCORPORATES EFFICIENT HEAT EXCHANGER AND SPECIAL AIR PATH STRUCTURE, MAKE FULL USE OF WASTE HEAT COMBUSTION FUEL GAS, IMPROVING HEAT UTILIZATION RATE, GOOD ENVIRONMENTAL PROTECTION INDEX, SAVES FUEL AND SHORTENS CREMATION TIME. 2. NEW REFRACTORY MATERIALS (EXCLUSIVE FORMULA) THAT ARE RESISTANT TO HIGH TEMPERATURE WITH LOW SPECIFIC HEAT. GREATLY EXTEND THE SERVICE LIFE. 3. SPECIAL CASTING MATERIAL, HIGH TEMPERATURE RESISTANCE, LONG SERVICE LIFE; SHORTENS THE COOLING CYCLE. THE BRICK STRUCTURE ON BOTH SIDES OF THE ASH PICKING FURNACE DOOR WILL NOT HAVE CRACKS CAUSED BY DESIGN OR QUALITY PROBLEMS GUARANTEED FOR ONE YEAR. REFRACTORY MATERIALS, THE FURNACE CONTACT ARE WITH FLAME HAS PHOSPHORIC ACID A CHARACTERISTIC COMBINATION BRICK WHICH CAN RESIST RAPID COOLING AND RAPID HEAT, AND THE ARCHED ROOF INCORPORATES HIGH ALUMINUM SINTERED MOLDING BRICK. THE FURNACE BODY IS SURROUNDED BY ALUMINUM SILICATE WOOL WITH GOOD HEAT INSULATION AND HEAT PRESERVATION PERFORMANCE. THE THICKNESS IS 180mm. 4. ALL OPERATING SYSTEMS OF THE EQUIPMENT HAVE THREE SETS OF OPERATION FUNCTIONS, NAMELY AUTOMATIC, SEMI-AUTOMATIC AND MANUAL, WHICH CAN BE SWITCH BETWEEN THEM WITHOUT INTERFERENCE. AUTOMATIC CONTROL, TELECOMMUNICATION OPERATION AND ANIMATION DISPLAY. KEEPING THE OPERATOR AWAY FROM THE CREMATION SITE AND PROTECTING THE OPERATOR. AT THE SAME TIME EQUIPPED WITH A STANDBY OPERATING SYSTEM. LOW NOISE MOTOR EQUIPMENT, THERMOCOUPLE RESISTANCE TO HIGH TEMPERATURE. ALL ELECTRICAL CABINETS OF THE EQUIPMENT ARE EXTERNAL. 5. THE OIL SUPPLY SYSTEM INCORPORATES AUTOMATIC CONTROL AND MANUAL CONTROL, AND INCORPORATES OIL PROTECTION TECHNOLOGY, WHICH CAN EFFECTIVELY PREVENT FUEL OIL FROM RUNNING, BUBBLING, LEAKING AND CAUSING FURNACE EXPLOSION ACCIDENTS INCLUDING ANTI-LEAKAGE TECHNOLOGY TO BETTER PROTECT THE PERSONAL SAFETY OF OPERATORS. 6. THE BLOWER, THE INDUCED DRAFT FAN, THE FURNACE DOOR MOTOR, THE BODY CART MOTOR, THE PREPARATORY DOOR MOTOR AND THE FLUE GATE MOTOR ARE ALL INSTALLED WITH AN INTEGRATED DEVICE FOR OVER-CURRENT AND SHORT-CIRCUIT PROTECTION. 7. SPECIAL DIESEL METERING DEVICE, ACCURATE METERING. QUANTITY: 1 Learn More

REFERENCE NUMBER: YY-1365 CONTINUOUS PRODUCTION LINE FOR IMPREGNATION, DRYING, ABRASIVE SPRAY, HEAT-SETTING OF SYNTHETIC FIBERS FOR ABRASIVE WADDINGS, WITH AIRLAY CARDING MACHINE AND FIBER PREPARATION DETAILS: MAIN FEATURES: - THREE LAYERS OVEN: TWO UPPER DRYING LAYERS WITH LENGTH OF 6+ 6 METERS; ONE LOWER CURING LAYER WITH A LENGTH OF 6 METERS; - HEATING: BY DIRECT HEATING WITH AUTOMATIC BURNERS; - CONVEYOR WIDTH: 2200mm; - WORKING WIDTH: 2000mm; - MAX DRYING AND POLYMERISATION TEMPERATURE: 230°C; - HEATING POWER: 4 BURNERS 350 KW EACH ONE, ABOUT TOTAL 1.400 KW; - VENTILATION: SEMI-CLOSED SYSTEM WITH 4 CENTRIFUGAL VENTILATORS; - ADJUSTABLE CONVEYOR SPEED BY A.C. MOTORS; - INSTALLED ELECTRIC POWER: 200 KW. APPROX.; - MECHANICAL SPEED: 2÷15 METERS PER MINUTE; - CONVEYOR DRIVING: BY A.C. MOTORS; - MANUFACTURED ARTICLE: SYNTHETIC FIBERS ABRASIVE WADDING. Learn More

REFERENCE NUMBER: R-9389

GE 7EA GAS TURBINE GENERATOR 60HZ PACKAGES

 

GE 7EA GAS TURBINE GENERATOR PACKAGES

85MW ISO EACH ON NATURAL GAS

THEY ARE IN STORAGE RIGHT NOW

OWNER HAD THEM SHIPPED BACK TO THE USA ABOUT A YEAR AGO.

THEY ARE UNUSED (NEVER FIRED) AND WERE BUILT IN 2008 BY GENERAL ELECTRIC

GE 7EA (PG7121) DUAL LIQUID FUEL TURBINES

HEAT RATE: 10,430 BTU/KWH

OUTPUT: 85MW ISO ON NATURAL GAS

CURRENTLY DUAL LIQUID FUEL- CRUDE (PRIMARY FUEL) AND DISTILLATE (BACK UP)

 

QUANTITY: 2

Learn More

TT-6338 COMPLETE PULP MILL SOLD IN SECTIONS-PARTS, CAPACITY 350,000 TPY 1. IN GOOD WORKING CONDITION 2. STOPPED 2023 3. EQUIPMENT NOT AVAILABLE FOR LONG 4. COMPLETE PULP MILL. Learn More

V-2170 GENERAL ELECTRIC (GE) STEAM TURBINE 615MW FOR PRODUCING ELECTRICITY STEAM TURBINE ONLY IS BEING OFFERED FOR SALE UNIT DETAILS: TURBINE SERIAL NUMBER: 270T764 GENERATOR SERIAL NUMBER: 290T764 RPM: 3600 TURBINE: DESIGN CODE: G12 CONTROL SYSTEM: MARK VI STAGES: 22 LSB LENGTH: 30” INITIAL STEAM TEMPERATURE: 1050F INITIAL STEAM PRESSURE: 3,515 PSIA EXHAUST PRESSURE: 3.45 HGA GENERATOR: CODE: L2D RATING: 750,000 KVA VOLTAGE: 21,000 POWER FACTOR: .9 AMPS: 20,620 EXCITER RATING/VOLTS: 605 AMOUNT OF STEAM NEEDED: 4,200,000 TONS PER HOUR, 3500 PSI YEAR OF THE MACHINE: MANUFACTURED BETWEEN 2009 AND 2016 (IT TAKES 5 TO 6 YEARS TO PRODUCE IT) TYPE OF STEAM TURBINE: IS IT A BACK PRESSURE OR EXTRACTION STEAM TURBINE TO PRODUCE LOW PRESSURE AND MEDIUM PRESSURE STEAM? [ANSWER] LOW AND MEDIUM STEAM PRESSURES IN PSI: [ANSWER] AMOUNT OF STEAM AVAILABLE FROM EACH PRESSURE LEVEL (IN POUNDS OR TONS): [ANSWER] SHIPPING DIMENSIONS: IT WILL OCCUPY A BULK SPACE FOR APPROXIMATELY 2500 TONS WEIGHT. IN ESSENCE, 25,000 TON SHIP NEEDS TO BE ENGAGED AND MOVING. QUANTITY: 1 Learn More

TT-4703 JENBACHER JW 316 GS POWER GENERATOR BHKW, 760 KVA, YEAR 1996, 50 Hz JENBACHER JW 316 GS YEAR OF CONSTRUCTION 1996 CONDITION USED BRAND: JENBACHER MODEL: JW 316 GS CONDITION: EXCELLENT (USED) Learn More

TT-4061 SOLAR MARS 100 GAS TURBINE, 0 HOURS, 14800 / NA HP SOLAR MARS 100 GAS TURBINE YEAR: 2012 0 HOURS TOTAL OPERATION 0 STARTS QUANTITY: Learn More

TT-3403 MONFORTS SINGLE LAYER STENTER MACHINE, WIDTH 2400mm, 6 CHAMBER GAS HEATED, YEAR 1995 MONFORTS SINGLE LAYER STENTER MACHINE 6 CHAMBER GAS HEATED BRAND: MONFORTS MODEL: MONTEX 8F-TWIN-AIR QUANTITY: 1 Learn More

REFERENCE NUMBER: C-3851

MONFORTS STENTER FOR KNITS

MODEL: MONTEX 6500 7F TWINAIR

7 CHAMBERS GAS HEATED

WORKING WIDTH: 2200mm

YEAR: 2012

 QUANTITY: 1

Learn More

TT-8593 GE TM2500GEN08 MOBILE GAS TURBINE GENERATOR, 10.5KV, YEAR 2025 1. GE TM2500GEN08 2. YEAR: JUNE 2025 3. 10.5KV 4. DUAL FREQUENCY 5. DUAL FUEL 6. DRY LOW EMISSION 7. HOURS: 0 8. WARRANTY: ONE YEAR QUANTITY: 1 Learn More