Search results for: 'Roll e'

REFERENCE NUMBER: M-4868 (1111275NKG10RX) L PUB BREWERY 20HL SPECIFICATION: 1. MALT HANDLING - CYLINDER-CONIC MALT SILO WITH 25M³ CONTENT, MADE IN FIBRE GLASS / PLASTIC, STANDING OUTDOOR ON STEEL CONSTRUCTION - MALT CONVEYORS / SPIRAL CONVEYOR INTO 1ST FLOOR - 2-ROLLER MALT MILL - GRIST CASE - FALL PIPE IN MASH COPPER (FOR DUST FREE MASHING-IN) - GIBBET-LIFT FOR BAGGED SPECIAL MALTS 2. BREWHOUSE TOWER BREWHOUSE FOR 20 HL / BREW, COMPLETE IN STAINLESS STEEL, BUILT 1994, STEAM HEATED, ISOLATED AND COVERED WITH STAINLESS STEEL SHEET, 2 CRANE EYELET, 2 STAINLESS STEEL PLATFORM, WITH: - MASH- / WORT COPPER WITH BOTTOM HEATING ZONE AND INTERIOR COOKER, SIDEWAYS AGITATOR, MANWAY ENTRANCE HATCH, LIGHTNING, STEAM REGULATION VALVE - LAUTER TUN, WITH STAINLESS STEEL RAKING MACHINE WITH SEW-DRIVE FROM TOP, WITH SPENT GRAINS SLIDER, STAINLESS STEEL FALSE BOTTOM, SPENT GRAINS HATCH, VERTICAL SIGHT GLASS, LIGHTNING, SPRAY HEAD, DOME LID WITH BUILT IN CONTROL CABINET - SPINDLE STATION WITH WASHING TABLE IN STAINLESS STEEL, ABOUT 1,5M WALL ASSEMBLED - HOT WATER TANK, WITH 30 HL, IN STAINLESS STEEL, ISOLATED AND COVERED WITH STAINLESS STEEL SHEET, HEATABLE, WITH MANWAY IN THE WALL, LEVEL DISPLAY - PRESSURE RAISING PUMP - WORT COOLING, 1-STAGE PLATE APPARATUS - WORT AERATION IN STAINLESS STEEL 3. FERMENTING- AND STORAGE TANKS - 5 CCTS, WITH 40 HL NET / 46 HL GROSS CONTENT, ALL TANKS 3 BAR, BUILT 1994, STANDING ON FEET, PI-ISOLATED FULLY WELDED WITH STAINLESS STEEL JACKET, WITH JACKET COOLING FROM CONE BELOW TO ½ WALL 60 LT COOLING JACKET 3 BAR, WITH MANWAY IN THE WALL, 2 OUTLETS WITH BUTTERFLY VALVES, TEMPERATURE SENSOR PT100, SPRAY HEAD, PULLED DOWN CLEANING PIPE WITH BUTTERFLY VALVE, BUNGING ARMATURE, OVER PRESSURE VALVE, SAMPLER, 2 CRANE EYELETS, 2 OF THE TANKS WITH LEVEL DISPLAY - DIGITAL TEMPERATURE CONTROL FOR 5 TANKS IN STAINLESS STEEL CONTROL CABINET - CIRCULATING PUMP IN STAINLESS STEEL, MOBILE, WITH SWITCH - MANY GOOD BEER HOSES - 6 X 10 HL BEER DISPENSING TANKS, MAKE DUO TANK, BUILT 2002, 3,0 / 4,3 BAR, COOL ABLE, ISOLATED WITH STAINLESS STEEL-JACKET FULLY WELDED, FOR INLINE-OPERATION, LYING IN RACK, SCREWED STAINLESS STEEL RACK, WITH PRESSURE ARMATURE, OUTLET ARMATURE WITH REDUCTION TO BARE CONNECTION, MANWAY WITH BIG SIGHT GLASS IN MANWAY LED - PANEL FOR 3 TYPES OF BEER 4. FILLING COMBINED BOTTLE-/KEGGING PLANT, WITH 1 CLEANING TUB, HEATED AND 1 REBUILT KEG: - BOTTLE CLEANING MACHINE FOR CLEANING OF 8 BOTTLES INSIDE AND OUTSIDE, FOR UP TO 2LT BOTTLES - BOTTLE FILLING STATION WITH HUB CYLINDER FROM BELOW, WITH SPLINTER PROTECTION - COMBINED KEG-CLEANING- AND FILLING STATION - BUILT IN CONTROL CABINET WITH SIEMENS S5 CONTROL AND OPERATING CONSOLE OP 7 5. OTHER EQUIPMENT - STEAM BOILER FOR ABOUT F280 KG/H, WITH GAS BURNER, FULLY SERVICED ON 4TH AUGUST 2014, BUILT IN 1994 - CONDENSATE TUB IN STAINLESS STEEL AT WALL AND SECOND SMALL S/S-TUB - WATER TREATMENT - STEAM REGULATION AND CONDENSATE VALVES IN CYCLE - STAINLESS STEEL CHIMNEY PLANT ABOUT 8-10M - AIR COMPRESSOR WITH WIND KETTLE, BUILT 1994 - COOLING PLANT / COLD WATER PLANT, MAKE L&R KÄLTETECHNIK, TYPE: WRK-17/SL/-5, PLANT BUILT 1997, COOLING AGENT R 407 C, WITH NEW COMPRESSOR AND NEW PLATE HEAT EXCHANGER IN 2014 FOR 10,000 € INVESTED, EVAPORATOR WITH 2 VENTILATOR OUTSIDE HANGING ON THE WALL 6.1 OTHERS - ABOUT 100 KETS, MAKE SCHÄFER, PLUS-KEGS, FLAT FITTING IN DIFFERENT SIZES, NEUTRAL - PARTY-KEGS, WITH BAVARIAN TAP, PU-COVERED IN BLACK AND WITH WOOD-OPTIC - ABOUT 800 NEUTRAL CLIP LOCK BOTTLES EACH 1 LT 6.2 DIMENSIONS THE ROOM HEIGHT IN BREWHOUSE AND CCTS IS 4.50M. THE PLANT AS ASSEMBLED ON 10.75 X 4.38M. PLEASE NOTE THAT THE BREWERY IS ONLY AVAILABLE AS A SINGLE SALE QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4644 (11112KDGH10R) J VAMATEX SILVER HS LOOMS MODEL LEONARDO YEAR 2004 WIDTH 1900mm – DOBBY – 8 COLORS MAKE: VAMATEX MODEL: LEONARDO YEAR: 2004 WIDTH: 1900mm STAUBLI ELECTRONIC DOBBY MODEL 2861 – 20 SHAFTS PRODUCING SHIRT CLOTH ONLY ACCESSORIES WITH EACH LOOM:  4 FEEDERS  13 FRAMES  5.000 HEDDLES  1.5 BEAMS  1 CLOTH ROLLERS NEW  RPM: 600  A.C. DRIVE MACHINES ARE STOPPED IN THE LAST MONTH AND ARE STILL IN THE FACTORY. QUANTITY AVAILABLE: 24 Learn More

REFERENCE NUMBER: M-4463 (1010EQWAXX9) K VOLKMANN TWO FOR ONE TWISTERS YEAR 2002-2003 AND ONE DOUBLER 1 SET SSM DOUBLER WINDER YEAR 2002 6 SETS VOLKMANN TFO YEAR 2002-2003 QUANTITY AVAILABLE: 7 Learn More

REFERENCE NUMBER: M-4403 (10103WETE9R) K VAMATEX 1152 S TOWEL WEAVING LOOMS YEAR 2001 WIDTH 3600mm DOBBY TOWEL WEAVING LOOMS VAMATEX 1152 S YEAR 2001 WIDTH 3600mm 4/8 COLORS FIMTEXTILE DOBBY LEVERS 14/16 EACH LOOM PROVIDED WITH: WEFT ACCUMULATORS: 3 OR 4 PER LOOM HEALD FRAMES: 14 PER LOOM HEDDLES AND DROP WIRES: 4,000 PER LOOM WARP BEAMS: 1.5 CLOTH ROLLERS: 1.5 QUANTITY AVAILABLE: 4 Learn More

REFERENCE NUMBER: M-4755 (111195DBJ10RL) L BABCOCK STENTER YEAR 1991 WIDTH 2000mm – 8 CHAMBERS (1) X BABCOCK STENTER – 5000 – 5800 TYPE YEAR 1991 8 CHAMBERS (TOTAL LENGTH OF THE DRYING TUNNEL MT. 24 WORKING WIDTH 2000mm BLOWERS MODEL JET-STAR WITH AIR CIRCUIT CIRCULATION TYPE ECON-AIR POSSIBILITY TO ADJUST AIR FLOW INDEPENDENTLY UPPER AND BELOW GAS HEATING SYSTEM HORIZONTAL PIN CHAIN CONICAL INPUT FIELD LENGTH MT. 3.5 TOTAL OVERFEEDING FOR NEEDLE CHAIN (+50%) ENTRY WITH E+L CONICAL FIELD REGULATOR MODEL KR-40 WITH FR1501 PHOTOCELL FEELER GROUP BIG ROLL ARM DEVICE FOR FABRIC OUTPUT ON A-FRAME TROLLEYS SPEED ADJUSTABLE FROM 7.5 TO 150 MT/MIN MACHINE IS PROVIDED OF: (1) X BABCOCK IMPREGNATING/SQUEEZING PADDER – 5805 TYPE 2 CYLINDERS WITH ROLLER WIDTH 2000mm (WORKING WIDTH 1850mm) STAINLESS STEEL IMPREGNATING THROUGH - 2 STAINLESS STEEL EXTERNAL TANKS WITH MIXER D.C. DRIVE WITH SYNCHRONIZATION (1) X MAHLO WEFT STRAIGHTENER RFMC TYPE – 4 OPTICAL HEADS (1) X VACUUM EXTRACTOR WITH FILTER AND WATER RECOVERY – VACUUM PUMP WITH 30HP POWER – TO EXTRACT WATER FROM DELICATE FABRIC BYPASSING THE SQUEEZING PADDER QUANTITY AVAILABLE: 1 Learn More

FEATURES: 1. ROBUST AND RELIABLE. 2. SUITABLE FOR A WIDE SPECTRUM OF MATERIALS, INCLUDING LDPE, LLDPE, AND RECYCLED PE. 3. CAN PRODUCE FILMS WITH VARIOUS BUBBLE SIZES FROM DIAMTER 6 TO DIAMETER 32, BY CHANGING THE ROLLER. 4. INDEX REVOLVING WINDER IS EASY TO OPERATE. 5. VARIABLE SPEED DRIVE CAN GREATLY REDUCE ENERGY CONSUMPTION. 6. THIS MODEL CAN ALSO BE USED FOR FILMS WITH TWO LAYER FILM MACHINE. SPECIFICATIONS: MODEL: 25 MAXIMUM WIDTH: 2530mm MAXIMUM OUTPUT: 190 KG/HR LINE SPEED: 1100M/HR TOTAL POWER: 140 KW MACHINE WEIGHT: 8200 KGS MODEL: 16 MAXIMUM WIDTH: 1630mm MAXIMUM OUTPUT: 120 KG/HR LINE SPEED: 1100M/HR TOTAL POWER: 85 KW MACHINE WEIGHT: 6500 KGS Learn More

REFERENCE NUMBER: M-3365 (88016MKH7UC) K TOYOTA AIR JET MODEL JAT 610 YEAR 2002 WIDTH 1900mm -STAUBLI CAM TOYOTA AIR JET JA2S-190TP-MF-T610 MODEL JAT 610 YEAR 2002 3 SETS WITH ELECTRONIC TAKE-UP AND TOP BEAM ATTACHMENT WITH ORIGINAL TOYOTA LET-OFF WORKING WIDTH 1900mm 2 COLOR 2 ACCUMULATOR STAUBLI POSITIVE CAM 1761A 8 TO 10 LEVERS INSTALLED 6 HEALD FRAMES SUPPLIED FOR EACH MACHINE MECHANICAL TAKE –UP ELECTRONIC LET-OFF 6 BAR WARP STOP BAR 5000 HEALDS AND DROPPERS ROTARY LENO SELVEDGE 4 NOS OF ROTARY LENO BOBBIN 3 BEAMS 1.8 CLOTH ROLLERS QUANTITY AVAILABLE: 42 Learn More

REFERENCE NUMBER: M-3366 (88020GYZ7UC) K TOYOTA AIR JET MODEL JAT 610 YEAR 2003 WIDTH 1900mm -STAUBLI CAM TOYOTA AIR JET JA4S-190TP-EF-T610 MODEL JAT 610 YEAR 2003 WORKING WIDTH 1900mm 4 COLOR 4 ACCUMULATOR STAUBLI POSITIVE CAM 1761A 8 TO 10 LEVERS INSTALLED 6 HEALD FRAMES SUPPLIED FOR EACH MACHINE ELECTRONIC TAKE –UP ELECTRONIC LET-OFF 6 BAR WARP STOP BAR 5000 HEALDS AND DROPPERS ROTARY LENO SELVEDGE 4 NOS OF ROTARY LENO BOBBIN 3 BEAMS 1.8 CLOTH ROLLERS QUANTITY AVAILABLE: 18 Learn More

REFERENCE NUMBER: M-3364 (88015MJS7UC) K TOYOTA AIR JET MODEL JAT 610 YEAR 1999 WIDTH 1900mm -STAUBLI CAM TOYOTA AIR JET JA2S-190TP-MF-T610 MODEL JAT 610 YEAR 1999 WORKING WIDTH 1900mm 2 COLOR 2 ACCUMULATOR STAUBLI POSITIVE CAM 1761A 8 LEVERS INSTALLED 6 HEALD FRAMES SUPPLIED FOR EACH MACHINE MECHANICAL TAKE –UP ELECTRONIC LET-OFF 6 BAR WARP STOP BAR 5000 HEALDS AND DROPPERS ROTARY LENO SELVEDGE 4 NOS OF ROTARY LENO BOBBIN 3 BEAMS 1.8 CLOTH ROLLERS QUANTITY AVAILABLE: 20 Learn More