Search results for: 'and ma'

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More

TT-2563 ROLLMAC MODEL STARLINE RBS-2600/3/16 COATING HEAD WITH FOAMIX (FOAM MAKING ATT.) AND ROLLMAC LABORATORY COATING MACHINE, WORKING WIDTH 2400mm, YEAR 2016 MACHINE SOLD WITH: LABORATORY ROLLMAC COATER VISCOSITY METER/ATTACHMENT EXCELLENT LIKE NEW CONDITION QUANTITY: 1 Learn More

REFERENCE NUMBER: M-3973 (99016AVEZ8RX)-D HOTMELT POWDER SCATTERING AND LAMINATING MACHINE-2200mm 1.LAMINATING LINE : MAKE : VILLARS (CH) ACTUALLY SANTEX YEAR: 1993 WORKING WIDTH : 2200mm (NOMINAL WIDTH 2M10) VOLTAGE: 3X380(400)V TOTAL POWER : 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION : INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997) : 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS : 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED 2.ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM : MAKE : MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR: 1999 OPERATING VOLTAGE : 3X380V CAPACITY ACCUMULATOR : +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) 3. SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE : MAKE: MENZEL YEAR: 2000 OPERATING VOLTAGE : 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT KNOWN PROBLEM : PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) 4.MISCELLANEOUS : SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS Learn More

TT-7654 SAURER EMBROIDERING MACHINE AND ELECTRONIC LASER CUTTING DEVICE, YEAR 1999 TO 2009 ITEM 001 SAURER EMBROIDERING MACHINE TYPE EPOCA II AS QUANTITY: 1 ITEM 002 SAURER EMBROIDERING MACHINE TYPE EPOCA II ASC QUANTITY: 2 ITEM 003 ELECTRONIC LASER CUTTING DEVICE QUANTITY: 1 Learn More

REFERENCE NUMBER: M-5158 (1212CVPGXX11) L COMPLETE TERRY WEAVING PLANT 1 WEST POINT DIRECT WARPER WORKING WIDTH 1.8M, FLANGE DIAMETER BEAM OUTPUT 940 MM, PRESSURE ROLLER 1 WEST POINT V-CREEL, 504 ENDS, 504 SPARE ENDS, PITCH 400 MM, WP ELECTRO SENSE 1 WEST POINT DIRECT WARPER, WORKING WIDTH 1.8M, FLANGE DIAMETER BEAM OUTPUT 940 MM, PRESSURE ROLLER 1 WEST POINT V-CREEL, 640 ENDS, 640 SPARE ENDS, PITCH 450 MM, WP ELECTRO SENSE 1 WEST POINT SIZING UNIT, 10 POSITION CREEL, WORKING WIDTH 1.8M, DIAMETER 940 MM SINGLE SIZE BOX, ROLLER WIDTH 1.8 M, SINGLE SQUEEZING 10 DRYING CYLINDERS, TEFLON COATED, PARRAFIN WEST POINT HEAD STOCK, WORKING WIDTH 2.7 M, FLANGE 1250 MM 1 WEST POINT SIZING UNIT, 10 POSITION CREEL, WORKING WIDTH 1.8M, DIAMETER 940 MM SINGLE SIZE BOX, ROLLER WIDTH 1.8 M, SINGLE SQUEEZING 8 DRYING CYLINDERS, 7 TEFLON COATED, PARRAFIN WEST POINT HEAD STOCK, WORKING WIDTH 3.0 M, FLANGE 1250 MM 1 WEST POINT SIZING UNIT, 8 POSITION CREEL, WORKING WIDTH 1.8M, DIAMETER 940 MM SINGLE SIZE BOX, ROLLER WIDTH 1.8 M, SINGLE SQUEEZING 7 DRYING CYLINDERS, 6 TEFLON COATED, PARRAFIN WEST POINT HEAD STOCK, WORKING WIDTH 2.7 M, FLANGE 1250 MM 1 SIZE KITCHEN , 5 STAINLESS STEEL MIXING TANKS WITH HEATING 7 MOTOCONO REMAIN WINDERS, 4 POSITIONS EACH 1 WARP BEAM STORAGE, 6 ROWS, 4 LEVELS, 14 M LENGTH 3 SHELVES SINGLE SIDED, 2 SHELVES DOUBLE SIDED WITH HUBTEX WARP BEAM LIFTER, MODEL 20TS 62 SULZER TERRY PROJECTILE LOOMS WITH JACQUARD (8) MODEL P7100 B330 F4 EP J D1, YEAR 4X 1989, 2X 1990, 2X 1991 WORKING WIDTH 3,3 M / 130” (7) STAUBLI E-JACQUARD CX-870, YEAR 1998-2004, 2688 HOOKS, CONTROLLER JC-5 (1) STAUBLI E-JACQUARD CX-860, YEAR 1997, 2688 HOOKS, CONTROLLER JC-4 (M/C 1989) GROUND AND PILE WARP BEAM 940 MM DIAMETER (2) MODEL P7200 B330 F4 J Q D1, YEAR 1X 1991, 1X 1995 WORKING WIDTH 3,3 M / 130” STAUBLI E-JACQUARD CX-870, YEAR 2004, 2688 HOOKS, CONTROLLER JC-5 GROUND AND PILE WARP BEAM 940/1250 MM DIAMETER (6) MODEL P7100 B330 F4 J D1, YEAR 1X 1991, 1X 1992, 4X 1994 WORKING WIDTH 3,3 M / 130” (4) STAUBLI E-JACQUARD CX-860, YEAR 1994, 2688 HOOKS, CONTROLLER JC-4 (2) STAUBLI E-JACQUARD CX-870, YEAR 2004, 2688 HOOKS, CONTROLLER JC-5 (M/C 1990/91) GROUND AND PILE WARP BEAM 940 MM DIAMETER (4) MODEL P7250 B330 F4 J D1, YEAR 2X 2000, 2X 2001 WORKING WIDTH 3,3 M / 130” STAUBLI E-JACQUARD CX-870, YEAR 2X 2001, 2X 2004, 2688 HOOKS, CONTROLLER JC-5 GROUND AND PILE WARP BEAM 940/1250 MM DIAMETER (5) MODEL P7100 B390 F4 EP J D1, YEAR 1X 1991, 1X 1992, 2X 1994, 1X 1995 WORKING WIDTH 3,9 M / 153” STAUBLI E-JACQUARD CX-870, YEAR 2003/2004, 2688 HOOKS, CONTROLLER JC-5 GROUND AND PILE WARP BEAM 940 MM DIAMETER (1) MODEL P7100 B390 F4 EP J D1, YEAR 1992 WORKING WIDTH 3,9 M / 153” SCHLEICHER MECHANICAL JACQUARD 3-08, YEAR 1990, 896 HOOKS CAM MOTION, 6 LEVERS INSTALLED, 4 FRAMES GROUND AND PILE WARP BEAM 940 MM DIAMETER (4) MODEL P7100 B390 F4 EP J D1, YEAR 1X 1992, 3X 1994 WORKING WIDTH 3,9 M / 153” STAUBLI E-JACQUARD LX-1602, YEAR 2006/2008, 3072 HOOKS, CONTROLLER JC-6 GROUND AND PILE WARP BEAM 940 MM DIAMETER (6) MODEL P7100 B390 F4 EP J D1, YEAR 1X 1992, 4X 1993, 1X 1994 WORKING WIDTH 3,9 M / 153” STAUBLI MECHANICAL JACQUARD CR-520S, YEAR 1993/94, 1344 HOOKS GROUND AND PILE WARP BEAM 940 MM DIAMETER (1) MODEL P7100 B390 F4 EP J D1, YEAR 1994, WORKING WIDTH 3,9 M / 153” STAUBLI MECHANICAL JACQUARD CR-520, YEAR 1995, 1344 HOOKS GROUND AND PILE WARP BEAM 940 MM DIAMETER (2) MODEL P7100 B390 F4 EP J D1, YEAR 1995, WORKING WIDTH 3,9 M / 153” STAUBLI E-JACQUARD LX-1600, YEAR 2006, 3072 HOOKS, CONTROLLER JC-5 GROUND AND PILE WARP BEAM 940 MM DIAMETER (4) MODEL P7100 B390 F4 J D1, YEAR 1995 , WORKING WIDTH 3,9 M / 153” STAUBLI E-JACQUARD CX-860, YEAR 1996, 2688 HOOKS, CONTROLLER JC-4 GROUND AND PILE WARP BEAM 940 MM DIAMETER (1) MODEL P7100 B390 F4 J D2, YEAR 1995 , WORKING WIDTH 3,9 M / 153” STAUBLI E-JACQUARD CX-960, YEAR 1996, 3072 HOOKS, CONTROLLER JC-4 GROUND AND PILE WARP BEAM 940 MM DIAMETER (8) MODEL P7200 B390 F4 J Q D1, YEAR 6X 1996, 2X 1997, WORKING WIDTH 3,9 M / 153” STAUBLI E-JACQUARD CX-870, YEAR 1998, 2688 HOOKS, CONTROLLER JC-5 GROUND AND PILE WARP BEAM 940/1250 MM DIAMETER (8) MODEL P7250 B390 F4 J D1, YEAR 6X 1997, 2X 1998 , WORKING WIDTH 3,9 M / 153” (4) STAUBLI E-JACQUARD LX-1600, YEAR 2000, 3072 HOOKS, CONTROLLER JC-5 (M/C 1997) (4) STAUBLI E-JACQUARD CX-870, YEAR 2000/01, 2688 HOOKS, CONTROLLER JC-5 (M/C 1997/98) GROUND AND PILE WARP BEAM 940/1250 MM DIAMETER (1) MODEL P7250 B390 F4 J D2, YEAR 1999 , WORKING WIDTH 3,9 M / 153” STAUBLI E-JACQUARD LX-1600, YEAR 2002, 3072 HOOKS, CONTROLLER JC-5 GROUND AND PILE WARP BEAM 940/1250 MM DIAMETER (1) MODEL P7250 B390 F4 J D3, YEAR 1999, WORKING WIDTH 3,9 M / 153” STAUBLI E-JACQUARD LX-1600, YEAR 2002, 3072 HOOKS, CONTROLLER JC-5 GROUND AND PILE WARP BEAM 940/1250 MM DIAMETER ALL MACHINES WITH 4 COLORS, AVERAGE 3 WEFT FEEDERS (ROH CHRONO HS AND SIMILAR), MIN. 3 CENTRAL TUCK IN UNITS PER MACHINE, SIDE TUCK IN UNITS, USTER LOOM DATA E-JACQUARD M/C WITH ELECTRONICALLY CONTROLLED COLOR SELECTION (EXCEPT 8 MECHANICAL M/CS) SPLIT BEAM EXECUTION, 1.5 PILE BEAMS, 1.5 GROUND BEAMS ON-LOOM TAKE-UP, 1.5 CLOTH ROLLS, 4 WEFT FEEDERS, 4 DROP WIRE BARS APPROX. 9000 DROP WIRES AND 4500 HEDDLES, LOOMDATA APPROX. 80% PLATINES INSTALLED STARTES OR STAUBLI HARNESS, ONE LIETTY GANTRY FOR TWO MACHINES LOOM POWER 5 OR 6 KW, JACQUARD POWER 2 KW 5 TONELLO AT GARMENT WASHING AND BLEACHING MACHINES MODEL G510, YEAR: 1 X 2002, 2 X 2003, 1 X 2004, 1 X 2007, TEMPERATURE 98C , CAPACITY 500 KG.EACH, TONELLO CONTROLS DIRECT STEAM OPERATED, CURRENTLY ALL ARE CONNECTED TO A CENTRAL DOSING SYSTEM (BUT EACH HAS ITS OWN DOSING SYSTEM AND CAN WORK AS INDEPENDENT M/C) FULL DRUM (NOT DIVIDED), 4 WATER ENTRIES AND 2 DRAINING OPENINGS CAPABLE OF WASHING, BLEACHING AND WATER EXTRACTION, HEAVY DUTY (SUITABLE FOR JEANS) 1 TONELLO AT GARMENT WASHING AND BLEACHING MACHINES MODEL G1 50 HS, YEAR 2007, TEMPERATURE 98°C, CAPACITY 50 KG. TONELLO CONTROLS, DIRECT STEAM OPERATED, AIR PRESSURE 7 BAR, HYDRAULICS 3 BAR, STEAM 10 BAR, FULL DRUM (NOT DIVIDED), 4 WATER ENTRIES AND 2 DRAINING OPENINGS CAPABLE OF WASHING, BLEACHING AND WATER EXTRACTION, HEAVY DUTY (SUITABLE FOR JEANS) 2 TRIVENETA GARMENT DRYERS, TYPE E550 PV YEAR 2001 MODEL 550 P CAPACITY 500 KG. EACH, DRYING CYCLE TIME IS HALF OF THE TONELLO = EACH MACHINE CAN SERVE 2 TONELLO MACHINES - SEMI AUTOMATIC LOADING AND DISCHARGING, STEAM OPERATED ITEMIZED SALE IS POSSIBLE – AGAINST OFFERS AVAILABLE IMMEDIATELY – STOPPED ON MILL FLOOR Learn More

TT-2390 LEE C. MOORE RIG 8 NATIONAL 1320 UE, CAPACITY 500,000 LBS. AND 800,000 LBS, 60 Hz, YEAR 2007 TO 2015 AUXILIARY EQUIPMENT: A) (16) 8” SLICK DRILL COLLARS B) (32) 6-1/2” O.D. X 2-13/16” I.D SLICK DRILL COLLARS C) 550 JOINTS 5” 19.50#, S-135 DRILL PIPE WITH HARD BAND AND TK LINED D) COMPRESSOR HOUSE WITH GRASSHOPPER E) MUD HOUSE F) TOOL HOUSE G) CHANGE HOUSE H) PARTS HOUSE I) (2) JUNK BOXES J) (1) SUB BOX K) (2) INGERSOLL-RAND MODEL K6U AIR HOISTS L) INTER-AMERICAN MODEL SURVEYOR WITH 15,000’ WIRE LINE M) KELLY: 5-1/4” HEX X 42’L N) KELLY DRIVE BUSHING O) KELLY SPINNER P) UPPER KELLY VALVE Q) LOWER KELLY VALVE, 5,000 PSI R) NATIONAL MODEL D DEAD LINE ANCHOR S) MARTIN DECKER, TYPE E, 900,000 LB. CAPACITY T) OPI PIPE SPINNER U) STEEL FRAMED RIG MATS V) WIRE SUITCASES W) TOOL PUSHER QUARTERS X) 12 PERSON CREW QUARTER Learn More

Learn More

TT-4794 SOLAR MARS 90 GAS TURBINE AND COGEN PLANT, 10000 KW, YEAR 1989 REBUILT 2014 SOLAR MARS 90 GAS TURBINE AND COGEN PLANT CONDITION USED QUANTITY: 1 Learn More

YY-2048 CASHMERE SLIVER MAKING MACHINE FOR CARDING AND SLIVER, OUTPUT 25 TO 50 METERS PER MINUTE DETAILS: CONDITION: NEW CORE COMPONENTS: PLC, ENGINE, MOTOR, CARD CLOTHING APPLICATION: CASHMERE AUTOMATIC GRADE: AUTOMATIC PRODUCTION EFFICIENCY: 99% VOLTAGE: 220 VOLTS OR AS PER CUSTOMER REQUIREMENT POWER: 5.8 KW DIMENSIONS (L X W X H): 3800 X 2750 X 1970(mm) WEIGHT: 6.5 KG MACHINE TYPE: RIGHT HAND DELIVERY CURTAIN: 2200 X 650 X 1350mm COILER: 900 X 600 X 1300mm CYLINDER SPEED: 80 RPM DOFFER SPEED: 8 RPM CHEST CYLINDER SPEED: 17 RPM TRANSFER ROLLER SPEED: 60 RPM OUTPUT: 25 TO 50 METERS PER MINUTE WEIGHT OF FIBER TOPS: 8 TO 12 GSM CERTIFICATION: CE QUANTITY: 1 Learn More

T-7932 GAUZE PRE-FOLDING AND X-RAY DETECTABLE THREAD ATTACHING MACHINE MODEL: ZBJ234 MACHINE DIMENSION: 2600 X 1800 X 1200mm POWER SOURCE: 380V/50Hz/3PH AC POWER CONSUMPTION: 3.0KW Learn More