Search results for: 'air compress'

YY-2176 AUTOMATIC PILLOW VACUUM PACKING MACHINE (HYDRAULIC SYSTEM) WITH FRONT AND BACK FEED CONVEYOR POWER: 7.5KW SEALING WIDTH: 800mm TABLE AREA: 800 X 800mm COMPRESSION STROKE: 350mm THE COMPRESSION HEIGHT CAN BE ADJUSTED AIR PRESSURE: <0.8MPA CAPACITY: 300 TO 350 PCS/H MAXIMUM PRESSURE: 5 TONS (OIL HYDRAULIC SYSTEM) OVERALL DIMENSIONS: 4100 X 1250 X 2030mm QUANTITY: 1 Learn More

J-2210 DRILLING MACHINE, 2100mm MAX DRILLING WIDTH, 6 TO 28mm HOLE DIAMETER DRILLING MACHINE VERTICAL DRILLING OF MATTRESSES AND PILLOWS BY MEANS OF SPECIAL INTERCHANGEABLE DRILLS WITH DIFFERENT DIAMETERS MATERIALS: EXPANDED PU FOAM, PE FOAM, VISCO, BONDED FOAM AND SIMILAR, LATEX EXCLUDED VERTICAL AND LATERAL MOVEMENTS OF THE THRUST YOKE ALLOW STRAIGHT AND CROSSED DRILLING, POSSIBLE TO OBTAIN 9 TYPES OF DRAWINGS FOR EACH MATTRESS COMPRESSED AIR JET TAKES FOAM SCRAPS OUT LEAVING HOLES FREE, WASTE EVACUATED WITH SMALL CONVEYOR AND SUCKED AND CONVEYED TO PROPER COLLECTOR STATION FOR RECYCLING CONTROLLED LUBRICATION DEVICE FOR DRILLS PNEUMATIC COMPRESSED DEVICE KEEPS MATTRESS FIRM DURING PERFORATION AND GUARANTEES BETTER PERFORMANCE EASY AND FAST REMOVING AND REPLACING OF DRILLS FEEDING AND UNLOADING CONVEYORS ARE CONTROLLED BY INVERTERS CONTROL CONSOLE COMPLETE WITH MULTIFUNCTION DEVICE (NEXUS) DRILLING SIMULATION AND PRODUCTION TIME AND COST COMPUTATION SOFTWARE INTERCONNECTION (INDUSTRY 4.0) QUANTITY: 1 Learn More

L-6683 DOUBLE BELT COMPRESSION THERMOBONDING OVEN SYSTEM 6000mm X 3300mm WIDE

INCLUDING:

THERMOBONDING OVEN
- DOUBLE COMPRESSION CONVEYORS SYSTEM SINGLE PASS
- DOUBLE BELT SOFT & HARD WADDING OVEN (6000mm LONG)
WORKING WIDTH: 3300mm
LENGTH OF HEATING CHAMBER: 6000mm
PANELS ARE 100mm THICK
TEMPERATURE INSIDE: UP TO 220 C
GAS BURNER 25 CUBIC METER PER HOUR DEPENDING ON MATERIAL THICKNESS
TWO GAS BURNERS ONE ON EACH SIDE 80 START AND 25 RUN CBM/H WITH MAINLINE 2 INCH
REDUCED TO 1” AT BURNER, PRESSURE 10 TO 15 KPascal
TWO HOT AIR FANS 22 KW EACH
ONE EXHAUST FAN 5.5 KW
WORKING SPEED: 1 TO 8 METERS PER MINUTE
DOUBLE TEFLON BELT WITH SINGLE PASS, WEAVE IS 2mm X 2mm
SUCTION HOOD AT THE ENTRANCE
THICKNESS OF FINAL PRODUCT 20 TO 150mm DEPENDING

COOLING UNIT
- FOUR COOLING PRESS ROLLERS 200mm diameter , 10mm shell thickness, with chiller
12,000 watt output power , input power 5700 watt , capacity 65 liter per minute
WORKING WIDTH: 3300mm
- LENGTHWISE CUTTER – 7 KNIVES ,pneumatically activated , BLADE DIAMETER 650mm
-SINGLE MOTOR
- MOVABLE SIDEWAYS
- CROSS CUTTER 2.2 KW MOTOR . UP TO 4 CUTS PER MINUTE
MAXIMUM LENGTH 2000mm
WORKING WIDTH: 2800mm
PVC CONVEYOR AT THE EXIT

ELECTRICAL CONTROL SYSTEM
-ELECTRICAL CABINET UL COMPONENTS

QUANTITY: 1

Learn More

REFERENCE NUMBER: L-2044 
MACHINE SIZE (W X D X H) 700 X 560 X 1200mm
QUANTITY: 1

Learn More

REFERENCE NUMBER: M-4868 (1111275NKG10RX) L PUB BREWERY 20HL SPECIFICATION: 1. MALT HANDLING - CYLINDER-CONIC MALT SILO WITH 25M³ CONTENT, MADE IN FIBRE GLASS / PLASTIC, STANDING OUTDOOR ON STEEL CONSTRUCTION - MALT CONVEYORS / SPIRAL CONVEYOR INTO 1ST FLOOR - 2-ROLLER MALT MILL - GRIST CASE - FALL PIPE IN MASH COPPER (FOR DUST FREE MASHING-IN) - GIBBET-LIFT FOR BAGGED SPECIAL MALTS 2. BREWHOUSE TOWER BREWHOUSE FOR 20 HL / BREW, COMPLETE IN STAINLESS STEEL, BUILT 1994, STEAM HEATED, ISOLATED AND COVERED WITH STAINLESS STEEL SHEET, 2 CRANE EYELET, 2 STAINLESS STEEL PLATFORM, WITH: - MASH- / WORT COPPER WITH BOTTOM HEATING ZONE AND INTERIOR COOKER, SIDEWAYS AGITATOR, MANWAY ENTRANCE HATCH, LIGHTNING, STEAM REGULATION VALVE - LAUTER TUN, WITH STAINLESS STEEL RAKING MACHINE WITH SEW-DRIVE FROM TOP, WITH SPENT GRAINS SLIDER, STAINLESS STEEL FALSE BOTTOM, SPENT GRAINS HATCH, VERTICAL SIGHT GLASS, LIGHTNING, SPRAY HEAD, DOME LID WITH BUILT IN CONTROL CABINET - SPINDLE STATION WITH WASHING TABLE IN STAINLESS STEEL, ABOUT 1,5M WALL ASSEMBLED - HOT WATER TANK, WITH 30 HL, IN STAINLESS STEEL, ISOLATED AND COVERED WITH STAINLESS STEEL SHEET, HEATABLE, WITH MANWAY IN THE WALL, LEVEL DISPLAY - PRESSURE RAISING PUMP - WORT COOLING, 1-STAGE PLATE APPARATUS - WORT AERATION IN STAINLESS STEEL 3. FERMENTING- AND STORAGE TANKS - 5 CCTS, WITH 40 HL NET / 46 HL GROSS CONTENT, ALL TANKS 3 BAR, BUILT 1994, STANDING ON FEET, PI-ISOLATED FULLY WELDED WITH STAINLESS STEEL JACKET, WITH JACKET COOLING FROM CONE BELOW TO ½ WALL 60 LT COOLING JACKET 3 BAR, WITH MANWAY IN THE WALL, 2 OUTLETS WITH BUTTERFLY VALVES, TEMPERATURE SENSOR PT100, SPRAY HEAD, PULLED DOWN CLEANING PIPE WITH BUTTERFLY VALVE, BUNGING ARMATURE, OVER PRESSURE VALVE, SAMPLER, 2 CRANE EYELETS, 2 OF THE TANKS WITH LEVEL DISPLAY - DIGITAL TEMPERATURE CONTROL FOR 5 TANKS IN STAINLESS STEEL CONTROL CABINET - CIRCULATING PUMP IN STAINLESS STEEL, MOBILE, WITH SWITCH - MANY GOOD BEER HOSES - 6 X 10 HL BEER DISPENSING TANKS, MAKE DUO TANK, BUILT 2002, 3,0 / 4,3 BAR, COOL ABLE, ISOLATED WITH STAINLESS STEEL-JACKET FULLY WELDED, FOR INLINE-OPERATION, LYING IN RACK, SCREWED STAINLESS STEEL RACK, WITH PRESSURE ARMATURE, OUTLET ARMATURE WITH REDUCTION TO BARE CONNECTION, MANWAY WITH BIG SIGHT GLASS IN MANWAY LED - PANEL FOR 3 TYPES OF BEER 4. FILLING COMBINED BOTTLE-/KEGGING PLANT, WITH 1 CLEANING TUB, HEATED AND 1 REBUILT KEG: - BOTTLE CLEANING MACHINE FOR CLEANING OF 8 BOTTLES INSIDE AND OUTSIDE, FOR UP TO 2LT BOTTLES - BOTTLE FILLING STATION WITH HUB CYLINDER FROM BELOW, WITH SPLINTER PROTECTION - COMBINED KEG-CLEANING- AND FILLING STATION - BUILT IN CONTROL CABINET WITH SIEMENS S5 CONTROL AND OPERATING CONSOLE OP 7 5. OTHER EQUIPMENT - STEAM BOILER FOR ABOUT F280 KG/H, WITH GAS BURNER, FULLY SERVICED ON 4TH AUGUST 2014, BUILT IN 1994 - CONDENSATE TUB IN STAINLESS STEEL AT WALL AND SECOND SMALL S/S-TUB - WATER TREATMENT - STEAM REGULATION AND CONDENSATE VALVES IN CYCLE - STAINLESS STEEL CHIMNEY PLANT ABOUT 8-10M - AIR COMPRESSOR WITH WIND KETTLE, BUILT 1994 - COOLING PLANT / COLD WATER PLANT, MAKE L&R KÄLTETECHNIK, TYPE: WRK-17/SL/-5, PLANT BUILT 1997, COOLING AGENT R 407 C, WITH NEW COMPRESSOR AND NEW PLATE HEAT EXCHANGER IN 2014 FOR 10,000 € INVESTED, EVAPORATOR WITH 2 VENTILATOR OUTSIDE HANGING ON THE WALL 6.1 OTHERS - ABOUT 100 KETS, MAKE SCHÄFER, PLUS-KEGS, FLAT FITTING IN DIFFERENT SIZES, NEUTRAL - PARTY-KEGS, WITH BAVARIAN TAP, PU-COVERED IN BLACK AND WITH WOOD-OPTIC - ABOUT 800 NEUTRAL CLIP LOCK BOTTLES EACH 1 LT 6.2 DIMENSIONS THE ROOM HEIGHT IN BREWHOUSE AND CCTS IS 4.50M. THE PLANT AS ASSEMBLED ON 10.75 X 4.38M. PLEASE NOTE THAT THE BREWERY IS ONLY AVAILABLE AS A SINGLE SALE QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4747 (1111NBRTHH10) L INDUSTRIAL BREWERY WITH BREWHOUSE 20 HL INDUSTRIAL BREWERY WITH CAPACITY OF 20 HL PER BREW YEAR PRODUCTIVITY OF 6,000 TO 7,000 HL, 3 SORTS OF BEER BREWERY IS NOT LOCATED AT A SEISMIC AREA EQUIPMENT DESIGNED ACCORDING TO EUROPEAN STANDARD STEAM HEATED 2-VESSEL BREW HOUSE OF 20 HECTOLITRES IN STAINLESS STEEL SCOPE OF SUPPLY: MALT MILL 1 X 2-ROLL MILL WITH CAPACITY OF 400 TO 800 KG/H WITH INLET FROM THE TOP FOR MALT SACKS BREW HOUSE 20HL STEAM HEATED STAINLESS STEEL 1.1 MASH/WORTH – KETTLE DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 LLC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF STAINLESS STEEL 2 STEAM HEATING ZONES (BOTTOM AND CYLINDRICAL PART) AGITATOR AND SHAFT IN STAINLESS STEEL, MATERIAL 1.4301. INSTALLATION OF BOTTOM CENTER. DRIVE VIA GEAR MOTOR, SPEED CONTROLLABLE BY FREQUENCY CONVERTER 1 SPRAY BALL 1 MAN HOLE WITH GLASS 1 PRESSURE RELIEF VALVE – SAFETY VALVE 1 LEVELMEASUREMENT DESIGNED FOR NON PRESSURE OPERATION 1.2 LAUTER TUN DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF STAINLESS STEEL ISOLATION OF THE CYLINDRICAL PART AND THE BOTTOM - 100 MM HALOGEN-FREE MINERAL WOOL. BOTTOM OF THE LAUTER TUN WITH OUTLET VALVES, BACK WASH VALVES AND A DRAIN VALVE MULTIPART SIEVE PLATE 1.4301 REMOVABLE THROUGH MANHOLE. HOEING 1.4301 TWO-ARMED WITH KNIVES AND TREBERN SWORD. INSTALLATION OF BOTTOM CENTER. 1 LAUTER STATION WITH CIP SPRAY BALL 1 MANHOLE WITH GLASS 1 SPRAY BALL 1 TREBERN FLAP AT THE CYLINDRICAL PART DESIGNED FOR NON PRESSURE OPERATION THE PACKAGE INCLUDES ALL VALVES, CHECK VALVES, BUTTERFLY VALVES, 2 PUMPS AND TEMPERATURE PROBES LANDING AND STAIRS MADE OF STAINLESS STEEL SQUARE ROOF BARS, COVERED WITH CORRUGATED SHEET METAL, HEIGHT ADJUSTABLE FEET WITH DOMES. THE PAN DUST WILL BE COLD DOWN WITH COLD WATER AND THE CONDENSATE WILL BE TRANSFERRED TO THE DRAIN WHIRLPOOL 20HL VESSEL MADE OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220. NON INSULATED. 1 WHIRLPOOL PUMP 2 LATERAL OUTLETS WITH HAND VALVES 1 FLOOR DRAIN WITH HAND VALVE 1 TANGENTIAL INLET PORT WITH THREADED CONNECTOR 1 SAFETY VALVE 1 MANHOLE 1 SPRAY BALL DESIGNED FOR NON PRESSURE OPERATION WORTHCOOLING + WORTH AERATION VESSEL MADE OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220. NON INSULATED. 1 WHIRLPOOL PUMP 2 LATERAL OUTLETS WITH HAND VALVES 1 FLOOR DRAIN WITH HAND VALVE 1 TANGENTIAL INLET PORT WITH THREADED CONNECTOR 1 SAFETY VALVE 1 MANHOLE 1 SPRAY BALL DESIGNED FOR NON PRESSURE OPERATION 1. SECTION: 20 HL WORTH IS COOLED WITH COLD WATER FROM 98°C TO 17°C IN 60 MINUTES (COLD WATER FROM CLIENT SIDE MUST BE MAX. 15°C OR LOWER) 2. SECTION: WITH ICE WATER OR GLYCOL THE WORTH IS COOLED TO 5°C CONTROL SYSTEM EACH PNEUMATIC CONTROLLED VALVE WILL HAVE A SWITCH BUTTON ON A CONTROL PANEL IN THE MIDDLE OF THE BREW HOUSE. ALSO THE TEMPERATURE CONTROL OF THE MASH KEETEL AND WORTH KETTLE WILL BE IMPLEMENTED AT THE CONTROL PANEL WITH A HARD WARE CONTROLLER. HOT WATER TANK 30 HL VERTICAL DESIGN, MATERIAL 1.4301 DOUBLE WALLED INNER SHELL OF STAINLESS STEEL, MATERIAL 1.4301 IIIC, WELDS GROUND WITH GRAIN SIZE 220 OUTER SHEATH MADE OF MATERIAL 1.4301 WITH GRAIN 220 1 HOT WATER PUMP 1 CIRCULATION PUMP 1 PT 100 AN CONTROLLER 1 STEAM VALVE AND CONDENSATE VALVE 1 LEVEL INDICATION 10 X CYLINDER CONICAL TANKS 40/48 HL VERTICAL DESIGN WITH DISHED BOTTOM AND 60° CONE. CONE AND CYLINDRICAL PART IS INSULTED AND THE FULL TANK IS EQUIPPED WITH WELDED STAINLESS STEEL EXTERIOR FINISH. TANK HEIGHT APPROX.: 4.050MM TANK EQUIPPED WITH COOLING JACKET (1 ZONE) AND CONE COOLING (2 ZONE), BY TEMP- PLATE, SUITABLE FOR ICE WATER / GLYCOL. SEPARATE CONNECTIONS FOR COOLING FOR CASING AND CONE : NIPPLE ¾ " EXTERNAL THREAD TANK WITH MANHOLE 500 X 400 MM, WITH MANHOLE COVER AND DUAL HINGE. 2 OUTLET DN 32 INSTALLED IN A DN 125 - THREAD , PULLED FORWARD AND ENDED BUTTERFLY VALVE DN 32 G / S , WITH BLANKING CAP. UPPER FLOOR PROVIDED WITH 2 THREADED CONNECTION DN 32 FOR CONNECTION OF AN RLV - FITTING. ONE OF THE TERMINALS INSTALLED IN A FITTING DN 100 AND DN 25 PROVIDED WITH REMOVABLE SPRAY BALL CLEANING PIPE DN25, TOP PROVIDED WITH CONNECTION CONE / NUT DN 32FOR CONNECTION TO THE RLV COMBINATION, PULLED DOWN AND ENDING ON OPERATING HEIGHT IN THREADED CONNECTION DN 50, INCLUDING BLANKING CAP. IN THE CLEANING DUCT 2 CONNECTOR WITH THREADED CONNECTION DN 20 FOR SPUND APPARATUS AND WITH BALL VALVE FOR THE GAS SUPPORT 1 CONNECTOR FOR SAMPLE VALVE: THREADED CONNECTION DN 20 2 CONNECTION FOR PT -100: IMMERSION SLEEVE 260 MM LONG, WITH SLEEVE ½ " . 2 SOLENOID VALVE FOR THE COOLING DUCT 4 MANUAL VALVES IN THE COOLANT INLET AND COOLANT OUTLET LINE 4 THE HEIGHT ADJUSTABLE TUBE FEET , INCLUDING FOOTPLATE. MATERIAL: 1.4301. FINISH: - INSIDE: - 2B (IIIC-SHEET), DISHED BOTTOM GROUND. - WELDS - ROUND & LONG SEAMS SANDED. - REST STAINED / BRUSHED. - OUTSIDE: - 2B (IIIC-SHEET). - WELDS - ROUND & LONGITUDINAL SEAMS SANDED. - REST STAINED / BRUSHED TANK SUITABLE FOR 3 BAR G. (20 ° C), DECREASE ACCORDING TO PED 97/23/EC. FILTRATION 20 HL/H KISELGUR- FILTER WITH HORIZONTAL SLICES AND CAPACITY OF 20HL / HOUR 3 X PRESSURE DISPENDING TANKS 40/46 HL VERTICAL DESIGN WITH DISHED BOTTOM LOWER + UPPER BOTTOM AND CYLINDRICAL PART IS INSULTED AND THE FULL TANK IS EQUIPPED WITH WELDED STAINLESS STEEL EXTERIOR FINISH. TANK HEIGHT APPROX.: 3.350MM TANK EQUIPPED WITH COOLING JACKET (1 ZONE) BY TEMP- PLATE, SUITABLE FOR ICE WATER / GLYCOL. CONNECTION FOR COOLING: NIPPLE ¾ " EXTERNAL THREAD TANK WITH MANHOLE 500 X 400 MM, WITH MANHOLE COVER AND DUAL HINGE. 1OUTLET DN 32 PULLED FORWARD AND ENDED BUTTERFLY VALVE DN 32 G / S , WITH BLANKING CAP. UPPER FLOOR PROVIDED WITH 2 THREADED CONNECTION DN 32 FOR CONNECTION OF AN RLV - FITTING. ONE OF THE TERMINALS INSTALLED IN A FITTING DN 100 AND DN 25 PROVIDED WITH REMOVABLE SPRAY BALL CLEANING PIPE DN 25, TOP PROVIDED WITH CONNECTION CONE / NUT DN 32 FOR CONNECTION TO THE RLV COMBINATION, PULLED DOWN AND ENDING ON OPERATING HEIGHT IN THREADED CONNECTION DN 32, INCLUDING BLANKING CAP. IN THE CLEANING DUCT 2 CONNECTOR WITH THREADED CONNECTION DN 20 FOR SPUND APPARATUS AND WITH BALL VALVE FOR THE GAS SUPPORT 1 CONNECTOR FOR SAMPLE VALVE: THREADED CONNECTION DN 20 1 CONNECTION FOR PT -100: IMMERSION SLEEVE 260 MM LONG, WITH SLEEVE ½ " . 1 SOLENOID VALVE FOR THE COOLING DUCT 2 MANUAL VALVES IN THE COOLANT INLET AND COOLANT OUTLET LINE 4 THE HEIGHT ADJUSTABLE TUBE FEET , INCLUDING FOOTPLATE. MATERIAL: 1.4301. FINISH: - INSIDE: - 2B (IIIC-SHEET), DISHED BOTTOM GROUND. - WELDS - ROUND & LONG SEAMS SANDED. - REST STAINED / BRUSHED. - OUTSIDE: - 2B (IIIC-SHEET). - WELDS - ROUND & LONGITUDINAL SEAMS SANDED. - REST STAINED / BRUSHED TANK SUITABLE FOR 3 BAR G. (20 ° C), DECREASE ACCORDING TO PED 97/23/EC. COOLING UNIT COOLING UNIT FOR THE OFFERT TANKS AND FOR THE WORTH COOLING. DESIGNED FOR OPERATION WITH GLYCOL COMPRESSOR OIL FREE FULLY AUTOMATIC, OIL-FREE AIR COMPRESSOR STATION WITH STAGE, MOUNTED ON A PRESSURE VESSEL, EQUIPPED WITH PRESSURE SWITCH, OUTLET VALVE, SAFETY VALVE, PRESSURE GAUGE AND MICRO FILTER. STEAM GENERATOR OIL OPERATED OIL OPERATED STEAM GENERATOR WITH A CAPACITY OF 200 KG/H INCLUDING FEED WATER TREATMENT AND FEED WATER CONTROL MOBILE BEER PUMP BEER PUMP WITH FREQUENCY CONVERTER, SINGLE MECHANICAL SEAL, ON STAINLESS STEEL FRAME (WITH CEE PLUG, MOTOR PROTECTION AND 10 M CABLE) FOR PUMPING FROM THE FERMENTATION TANKS TO THE PRESSURIZED TANK 4 PCS. BEER HOSES SET KEG-CLEANER WITH KEG-HANDFILLER CLEANER: CAPACITY: 10 – 15 KEGS / HOUR SEMI AUTOMATICALLY CLEANING PROCESS FOR ALL STANDARD KEGS KEG-HAND FILLER: COMPLETE MADE OF STAINLESS STEEL TUBES 2M LONG FOR ALL STANDARD KEGS PACKAGING WOODEN BOX AND FOILING FOR TRANSPORT IN A CONTAINER (SEA WAY), THE WOODEN BOX ALONE IS NOT ENOUGH FOR THE SEA WAY DOCUMENTATION IN ENGLISH (DEVICE DOCUMENTATION) IN ELECTRONIC FORM MOUNTING MATERIAL FOR MECHANICAL AND ELECTRICAL WORK UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING MOUNTING AND COMMISSIONING FOR MECHANIC WORK AND ELECTRIC WORK (LIFTING DEVICES- CRANE, ENERGY, RAW MATERIAL, CLEANING SOLUTION, HOTEL, FLIGHT TICKET, LABOURER FOR MOUNTING SUPPORT) UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING 4 TEST BREWS (ENERGY, RAW MATERIAL, CLEANING SOLUTION, HOTEL, FLIGHT TICKET) AND TRAINING OF THE OPERATOR STAFF UPON RECEIPT OF THE LAYOUT DRAWING, SPECIFICATIONS OR INTERFACES AND CLARIFYING THE SCOPE OF DELIVERY WE CAN MAKE A DETAILED QUOTE FOR DELIVERY, INSTALLATION, AND COMMISSIONING LABORATORY CIVIL WORK CO2 – SUPPLY PERMITS AND LICENSES FROM LOCAL AUTHORITIES TRANSPORT WATER TREATMENT AND COLD WATER TANK (IF REQUIRED) YEAST MANIPULATION (IF REQUIRED) Attached 3 photos from similar equipment. F1: brewhouse F2: CCT (cylindroconicalk tanks) and BBT (bright beer tanks = dispensing tanks) F3: PHE(plate heat exchanger = wort cooling, whirlpool, hot water tank) QUANTITY AVAILABLE: 1 Learn More

TT-8633 STX MAN DIESEL/HFO 18V32/40 GENSETS, 9.0 MW, 50/60 Hz 1. STX MAN DIESEL/HFO 18V32/40 GENSETS 2. GROSS ELECTRICAL OUTPUT APPROX. 9.0 MW 3. BRAND MAN DIESEL & TURBO, TYPE 18V32/40 - 4 STROKE, UNUSED EACH UNIT CONSISTS OF MOTOR, GENERATOR, RACK / BASE-FRAME QUANTITY: 20 UNITS Learn More

YY-3557 9 MW GENERATOR-SETS MAN, TYPE 18V32/40 – 4 STROKE, 50 Hz, 25 UNITS UNUSED EACH GENERATOR-SET IS COMPLETELY ASSEMBLED AND CONSISTS OF ENGINE, NEW GENERATOR, NEW MOTOR CONTROL AND BASE FRAME / RACK. THE MAN ENGINES CAN BE OPERATED WITH BOTH HEAVY OIL AND LIGHT OIL; THEY WILL BE PRE-ADJUSTED FOR THE FUEL QUALITY OF THE CUSTOMER. PLEASE HAVE A LOOK AT THE ATTACHED DATA SHEET. Learn More

YY-3556 4 X 60 MW GE LM6000 PD 15PPM SPRINT GAS TURBINE POWER PLANT HISTORY: THE POWER PLANT CONSISTS OF X 50 MW GE LM6000 PD 15PPM SPRINT GAS TURBINE, ALL OF YEAR: 2011, 7000 HRS SINCE NEW EACH, 3000 RPM, 50 Hz, X 13 MW SIEMENS SST 300 STEAM TURBINE WITH 5000 HOURS EACH. PLANT WAS COMMISSIONED AND PUT INTO OPERATION IN 2012. QUNATITY: 1 Learn More

TT-7918 MAN HFO 18V32-40 GENERATING SETS - NEW, 50 Hz, 11 KV 1. MAN HFO 18V32-40 GENERATING SETS 2. NEW 3. MODEL 18V32-40 4. GROSS ELECTRICAL OUTPUT APPROX. 9,0 MW 5. DOUBLE FUEL 6. MAN DIESEL ENGINES 18V32/40, NEVER INSTALLED, MANUFACTURED AT MAN-GERMANY. 7. THE GROSS ELECTRICAL OUTPUT OF THIS PLANT IS APPROXIMATELY 9 MW EACH SPECIFIED AT THE GENERATOR TERMINALS. 8. THE OFFERED ENGINES ARE DESIGNED FOR FIRING BY GAS OR HFO/DIESEL. IN THIS OFFER THE AUXILIARY IS LISTED TOR 1 UNIT, SO THE DESCRIPTIONS REFER TO 1 UNIT ONLY. ALL ENGINES ARE EQUIPPED WITH BRAND NEW ABB GENERATORS BASED ON THE LIMITED INFORMATION AVAILABLE THE PRICE IS OF BUDGETARY NATURE. 9. PRICE IS BASED ON SEVERAL ASSUMPTIONS THAT NEED TO BE CONFIRMED/UPDATED BEFORE A FIRM CONTRACT OFFER CAN BE MADE. QUANTITY: 12 Learn More