Search results for: 'Fiber machi'

T-8028 HIGH SPEED SOFT WINDING MACHINE SIZE: 2050 X 750 X 1500mm SINGLE-SIDE CONFIGURATION: 6 SPINDLES/SET WEIGHT: 150KG QUANTITY: 1 SET (6 SPINDLES) Learn More

REFERENCE NUMBER: J-2326
QUILTER FOR RAGS, 12 INCH WIDTH – NEW – RAG QUILTER

QUILTING MACHINE FOR RAGS
SEWS RAGS CONTINUOUSLY
SEW HEAD: 7 NEEDLES AND 7 LOOPERS 
MAKES A CHAIN STITCH ON THE CONVEYED RAGS
USES OVERLOCK THREAD
DISTANCE BETWEEN NEEDLES: 250mm (ENSURES THAT EVEN SMALL RAGS ARE SEWN)
1 HP MOTOR, 3-PHASE, 220 VOLT
WITH FREQUENCY INVERTER TO ADJUST THE ROTATION SPEED OF THE MOTOR AS NEEDED
HEIGHT: 1800mm
WIDTH: 960mm
DEPTH; 370mm
CONVEYOR WIDTH: 200mm
CONVEYOR LENGTH: 1560mm
MACHINE TOTAL LENGTH WITH CONVEYOR: 2800mm

AFTER SEWING, THE QUILT IS TRANSPORTED OUT INTO ROLLS WHICH CAN BE CUT ACCORDING TO CUSTOMER NEEDS
OPERATION: PLACE A LARGER RAG AS THE BOTTOM LAYER, SMALLER RAGS AS FILLING, AND ANOTHER LARGER RAG AS THE TOP LAYER. OPERATION REQUIRES 2 TO 3 OPERATORS.
TO REDUCE THE NUMBER OF OPERATORS REQUIRED, A FIBER ROLL AS CAN BE USED AS THE LOWER LAYER. THIS ALSO INCREASES THE PRODUCTION RATE.
DAILY PRODUCTION: VARIES BETWEEN 300 TO 500 KG PER 8 HOURS OF OPERATION
FOR KNIT FABRICS SUCH AS COTTON, VISCOSE, SWEATSHIRT FLEECE, NYLON STRETCH-FABRIC, PIQUET AND POPELINE
THERE IS NO MATERIAL WASTE AS THE MACHINE USES 100% OF THE RAGS
WORKING WIDTH: 12 INCHES
NEEDLE SPACING: 1 INCH
WITH LOOPER STRUCTURE SIMILAR TO THE DIAGRAM BELOW (REDUCES BOTTOM THREAD BREAKAGE)
MACHINE IS NEW, MADE TO ORDER
LEAD TIME: 10 DAYS

Learn More

REFERENCE NUMBER: M-3561

LINE FOR THERMO BONDED WADDING YEAR 1987 - FOR MATTRESS AND BUILDING SECTOR, ETC

 

LINE FOR THERMO BONDED WADDING  -YOC  1987  - FOR MATTRESS AND  BUILDING SECTOR, ETC.

( ESPECIALLY IN POLYESTER + NATURAL FIBERS MIXED).

THE LINE HAS A PRODUCTION OF 350/400 KGS PER HOUR WITH A WORKING WIDTH FROM 150 CMS INTIL 240.

 

COMPOSITION :

. BONINO LOADER   WORKING WIDTH  mm. 2800

. BONINO CARDING MACHINE WORKING WIDTH  mm. 2800 SINGLE DOFFER

. TECHNOPLANTS CROSS LAPPER WORKING WIDTH   ENTRY/EXIT mm. 3000

. SICAM OVEN  - 2 FIELDS. WORKING WIDTH  2400 mm. + COOLING SECTION

. TECNICA TESSSILE CUTTING MACHINE WITH HORIZONTAL AND VERTICAL CUT WORKING WIDTH  mm. 3000

. MECAP  PACKAGING MACHINE FOR ROLLS

 

QUANTITY: 1

Learn More

REFERENCE NUMBER:   G-8230

HIGH-TEMPERETURE AND HIGH-PRESSURE YARN DYEING MACHINE 40KG

 

DESIGNED FOR DYEING, BOILING OFF, BLEACHING, AND WATER WASHING, ETC. SUITABLE FOR HANK YARN, BOBBIN OR RAW STOCK FIBER

 

MACHINE TYPE: VERTICAL CYLINDER

VAT DIAMETER: Ф600mm

CONE QUANTITY: 7 X 7 = 49 CONES

WORKING TEMPERATURE: 130C

MAX WORKING PRESSURE: 0.4MPA

BOTH RATIO: 1:7 TO 9

WITH COMPUTERIZED CONTROL SYSTEM

HEAT EXCHANGING: COIL TYPE HEAT EXCHANGER, WHICH CAN BE USED FOR EITHER HEATING OR COOLING.

HEAT EXCHANGING SPEED: WHEN THE HEATED STEAM PRESSURE IS 0.4MPA, 40MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BARREL RAISING FROM 20^OC TO 130^OC. WHEN THE COOLING WATER PRESSURE IS 0. 3MPA AND THE WATER TEMPERATURE IS 20 ^OC, 40 MINUTES WILL BE REQUIRED FOR THE LIQUID INSIDE THE DYEING BECK TO LOWER FROM 130^OC TO 80^OC.

RECYCLING OF DYEING LIQUID: THE POSITIVE AND NEGATIVE RECYCLING OF DYEING LIQUID WILL BE ADJUSTED BY THE CYLINDER THROUGH THE SWITCHING DEVICE INSIDE THE CENTRIFUGAL PUMP.

SEALING OF BOILER: RUBBER ADHESIVE

THE WORKING PRESSURE INSIDE THE TANK WILL MAKE THE RUBBER SEAL CLOSELY TO ATTACH THE FLANGE. THE CONICAL SURFACE OF THE TANK MOUTH IS TO ENHANCE THE SEALING.

OPENING OF TANK COVER: FIRST OPEN THE AIR VALVE TO RELEASE THE PRESSURE INSIDE THE BOILER. WAIT UNTIL NO EXHAUSTED AIR GOING THRU THE EXHAUST VALVE AND THE READING OF PRESSURE GAUGE IS ZERO, WITHDRAW THE WRENCH HANDLE, OPEN THE CLAMPING HOOP TO REMOVE THE FLANGE; AND THEN OPEN THE COVER WITH DRAG WEIGHT. THE COVER WILL BE CLOSED.

 

CONFIGURATION:

1. ELECTRICAL CABINET: STAINLESS STEEL CABINET, PLASTIC COATING

2. ELECTRICAL COMPONENTS: SIEMENS, OMRON

3. COMPUTER: HG COMPUTER (MADE IN CHINA)

4. ELECTROMAGNETIC VALVE: TAIWAN YADEKE

5. PUMP: CENTRIFUGAL PUMP

6. MOTOR: WANNAN MOTOR

7. TEMPERATURE CONTROL: COMPUTER CONTROL, WITH HEATING, COOLING, KEEPING WARM, ETC. FUNCTION.

8. HEAT EXCHANGER: INTERNAL COIL HEATING

9. VALVE: STAINLESS ANGLE VALVES, PNEUMATIC BUTTERFLY VALVES

10. ONE CARRIER BASKET

11. MACHINE BODY MATERIAL: STAINLESS STEEL, 316 LITERS

12. ACCESSORIES: SEAL RING FOR DYE VAT, SEAL FOR MAIN PUMP, SEAL FOR REVERSING SHAFT

 

QUANTITY: 1

Learn More

TT-8359 BEFAMA CU 600 CARDING MACHINE, WORKING WIDTH 2200mm, YEAR 1983 QUANTITY: 1 Learn More

TT-6047 FEHRER NL36/150, YEAR 1995 FEHRER NL36/150 YEAR OF PRODUCTION: 1995 NEEDLE DENSITY: 2 X 4000 N/M QUANTITY: 1 Learn More

TT-5254 PIERRET CUTTING MACHINE FOR TEXTILES QUANTITY: 1 Learn More

TT-4959 RIETER COTTON RING SPINNING PLANT WITH 26112 SPINDLES, YEAR 2010 TO 2016 RIETER COTTON RING SPINNING PLANT 26112 SPINDLES PRODUCTION YEAR: 2016 BRAND: RIETER STATE: USED QUANTITY: 1 Learn More

J-5182 USTER HVI 1000, MODEL 700, YEAR 2011 MAKE: USTER MODEL: HVI 1000, MODEL 700 YEAR: 2011 (JULY), INSTALLED JANUARY 2012 QUANTITY: 1 Learn More

TT-4144 F.O.R. DOUBLE DOFFER ROLLER CARD LINK WITH TRUETZSCHLER FBK 536, WIDTH 3500mm, YEAR 1998 ITEM 001 DOUBLE DOFFER ROLLER CARD BRAND: F.O.R. MODEL: INJECTION 06803/D47C YEAR 1998 COMPLETE WITH: ITEM 002 TRUETZSCHLER FBK 536 CHUTE FEED WIDTH 3500mm YEAR 1998 Learn More