Search results for: 'HIGH PREC'

REFERENCE NUMBER: T-6870 MEDICAL FACE MASK AIR EXCHANGE DIFFERENTIAL PRESSURE TESTER, 60Hz MEDICAL FACE MASKS AIR EXCHANGE DIFFERENTIAL PRESSURE TESTER IS SUITABLE FOR DETERMINING THE AIR EXCHANGE DIFFERENTIAL PRESSURE OF MEDICAL FACE MASKS. IT CAN ALSO BE USED FOR THE DETERMINATION OF OTHER TEXTILE MATERIALS. STANDARDS: EN 14683-2014 ASTM F2100-2019 YY 0469-2011 YY 0969-2013 FEATURES: EQUIPPED WITH HIGH PRECISION DIFFERENTIAL PRESSURE SENSOR, DIGITAL DISPLAY OF THE DIFFERENTIAL PRESSURE OF BOTH SIDES OF THE SPECIMEN; SPECIAL SAMPLE HOLDERS TO ENSURE CLAMP THE SPECIMEN FIRMLY. KEY SPECIFICATION: AIR SOURCE: SUCTION TYPE AIRFLOW: 8L/MIN SEALING METHOD: END FACE SEAL DIAMETER OF TEST AREA: Ф25mm RANGE OF DIFFERENTIAL PRESSURE SENSOR: 0 TO 500PA DISPLAY METHOD: DIGITAL DISPLAY OF THE DIFFERENTIAL PRESSURE POWER SUPPLY: AC220V, 60Hz QUANTITY: 1 SET Learn More

REFERENCE NUMBER: Y-2076 TEMPERATURE AND HUMIDITY TEST CHAMBER THIS SERIES OF TEMPERATURE TEST CHAMBER IS SUITABLE FOR THE RELIABILITY TEST OF INDUSTRIAL PRODUCTS. IT HAS THE CHARACTERISTICS OF TEMPERATURE AND HUMIDITY CONTROL PRECISION AND WIDE CONTROL RANGE. ELECTRICAL AND ELECTRONIC PRODUCTS ENVIRONMENTAL TEST EQUIPMENT BASIC PARAMETERS VERIFICATION METHOD LOW TEMPERATURE, HIGH TEMPERATURE, CONSTAMP DAMP HEAT, ALTERNATING WET HEAT TEST EQUIPMENT REQUIREMENTS. SAMPLE REQUIREMENTS IN ORDER TO MAKE YOUR TEST DATA MORE REALISTIC AND EFFECTIVE, THE TEST CHAMBER SHOULD BE USED REASONABLY WHILE SATISFYING THE FOLLOWING PRINCIPLES. THE TOTAL MASS LOAD IS NOT MORE THAN 80 KG PER CUBIC METER OF CHAMBER VOLUME. THE TOTAL VOLUME OF THE LOAD IS NOT MORE THAN ⅕ OF THE WORKING CHAMBER VOLUME IN ANY SECTION PERPENDICULAR TO THE DOMINANT WIND DIRECTION, THE SUM OF THE LOAD AREAS SHOULD BE NO MORE THAN ⅓ OF THE CROSS-SECTIONAL AREA OF THE WORKING CHAMBER. DO NOT BLOCK THE FLOW OF AIRFLOW WHEN THE LOAD IS PLACED. VOLUME DIMENSION: ABOUT 150L INTERIOR SIZE: W: 600mm H: 600mm D: 460mm THE MAIN TECHNICAL PARAMETERS TEST CONDITION COOL METHOD: AIR COOLED MEASURED AT A ROOM TEMPERATURE OF + 25℃ UNDER NO LOAD, THE TEMPERATURE AND HUMIDITY PERFORMANCE TEST IS MEASURED ACCORDING TO THE RELEVANT REGULATIONS. THE SENSOR IS PLACED AT THE AIR OUTLET OF THE AIR HANDLING UNIT TEMPERATURE UNIT RANGE: 40 ℃ TO + 150 ℃ TEMPERATURE FLUCTUATION ± 0.5 ℃ TEMPERATURE UNIFORMITY: ≤ 2.0 ℃ TEMPERATURE DEVIATION: ≤ ± 2.0 ℃ TEMPERATURE CHANGE RATE HEAT UP RATE: - 40 ℃ TO +100 ℃ FULL RANGE AVERAGE SPEED: APPROX 45 MINUTES (NO LOAD) COOLING RATE: +20 ℃ TO 40 ℃ FULL RANGE AVERAGE SPEED: APPROX 60 MINUTES (NO LOAD) QUANTITY: 1 Learn More

REFERENCE NUMBER: Y-2073 RAIN TEST CHAMBER WATER SPRAY SIMULATION THIS EQUIPMENT IS APPLICABLE TO THE TEST OF RAINPROOF DUST AND SAND SOAKED WATER OF VARIOUS AUTO PARTS, ELECTRONIC APPLIANCES, AND OTHER INDUSTRIAL ELECTRONIC PRODUCTS. AUTO PARTS INCLUDE THE TEST OF FULL SEALING STABILITY OF THE SYSTEM SUCH AS LAMPS, DOOR LOCKS, ELECTRICAL, INSTRUMENTS, DUST COVERS, ELECTRONIC HOUSEHOLD APPLIANCES, ETC. THE TESTED ITEMS ARE INSTALLED OR PLACE IN THE CENTER OF SEMICIRCLE BENDING TUBES AND BOTTOM AND SWING OF THE SPLASHED SAMPLES. THE AXIS IS IN A HORIZONTAL POSITION, AND THE SAMPLES ROTATES AROUND THE CENTERLINE DURING THE TEST. TECHNICAL PARAMETERS: CHAMBER SIZE: 600mm X 600mm X 600mm (WxDxH) DIAMETER OF SPRAY: ⊄0.4mm SPACING OF SPRAY HOLES: 50mm SPRAY PIPE DIAMETER: 16mm NOZZLE ANGLE ADJUSTABLE: 120 (IPX3) 180(IPX4) RADIUS OF SPRAY RING: R 375mm WATER PRESSURE: ADJUSTABLE WATER FLOW AS REQUIRED FLOW: 1 TO 7L PER MINUTE, FLOW SPEED ADJUSTABLE AIR VELOCITY: 10mm PER SECOND TEST TIME: 0 TO 999 MIN ADJUSTABLE SWING ANGLE AMPLITUDE OF SWING TUBE: ±45˙ ± 60˙ ±180˙ PENDULUM TUBE: IT IS DRIVEN BY SERVO MOTOR, WITH HIGH PRECISION AND ACCURATE TIME AND SWING WATER SUPPLY PIPELINE: PPR PIPE IS USED FOR EQUIPMENT WATER SUPPLY, WHICH IS ARRANGE ACCORDING TO BOX DISTRIBUTION AND CONTROLLED BY EQUIPMENT CONTROL SYSTEM CABINET. HEATING MODE: INCORPORATE STAINLESS STEEL HEATING PIPE, SHALLOW WATER PLATE SURFACE EVAPORATION. SPRAY CYCLE: THE SPRAY CYCLE IN THE BOX IS ADJUSTABLE, AND THE DOOR IS EQUIPPED WITH AN OBSERVATION WINDOW TO OBSERVE THE STATE OF THE SAMPLE IN THE BOX. WINDOW WIPED INSTALLED. QUANTITY: 1 Learn More

SEMI-AUTOMATIC NOSE CLIP WELDING MACHINE FOR NOSE CLIP WELDING FOR DUST MASK RESPIRATORS, IT’S EASY TO OPERATE, FIRM WELDING EFFECT. THIS MACHINE INCORPORATES CONSTANT TEMPERATURE WELDING, WHICH IS NOT HARMFUL TO THE FABRIC, IT’S THE IDEAL MACHINE FOR DUST MASK RESPIRATOR MANUFACTURING.

 

FEATURES:

1. THIS MACHINE IS EASY TO OPERATE; THE GLUED ALUMINUM NOSE CLIP IS MOVED BY PNEUMATIC THEN WELDED ONTO THE MASK.

2. IT’S HIGH PRECISION AND THE NOSE CLIP WELD IS FIRM.

3. WELDING WITH CONSTANT TEMPERATURE WHICH IS NOT HARMFUL TO THE FABRIC.

 

ITEM NAME	TECHNICAL PARAMTER	QTY	REMARK
SPECIFICATION	1200mm X 650mm X 1000mm	1	HONGDA
WEIGHT	50KG
EFFICIENCY	8 TO 15PCS/MIN
VOLTAGE	220V/380V
AIR PRESSURE	5KG/CM²
FREQUENCY	20KHZ
POWER	600W
MOLD SERVO MOTOR	SGM7G-09AFC61 4.4KW	1	YASKAWA
ULTRASONIC POWER SERVO MOTOR	SGM7G-13AFC61 1.3KW	2	YASKAWA
MATERIAL PULLING SERVO MOTOR	SGM7G-09AFC61 0.85KW	2	YASKAWA
MATERIAL FEEDING/CORRECTING/INDENTATION MOTOR	130BYG-350A	4	SONGYANG
POUCHING MOTOR	110BYG-350B	4	SONGYANG
110 STEPPER MOTOR	110BYG-350A	10	SONGYANG
UP AND LOWER MOTOR	90BYG-350A	2	SONGYANG
STEPPER MOTOR 56	SY57STH56-2004A	8	SONGYANG
DIRECT CURRENT MOTOR	0.4KW	2
DIRECT CURRENT MOTOR	0.6KW	1
ASYNCHRONOUS THREE-PHASE MOTOR	90S-6	1	0.75KW
FREQUENCY CONVERTER	AVF200-0152	1	1.5KW
MAIN PNEUMATIC COMPONENTS: AIRTAC(TAIWAN); MAIN ELECTRICAL COMPONENTS: PANASONIC(JAPAN), SICK(GERMANY), DONLIM(CHINA&JAPAN), ETC.

 

EMAIL US FOR PRICE & PICTURES

INCLUDE OUR REFERENCE NUMBER

 

Learn More

MAKE: CIBITEX
EASYWIND IS A POWERFUL MOTORIZED HIGH-PRECISION UNWINDING/REWINDING COUPLING UNIT DESIGNED SPECIFICALLY TO WIND AND REWIND ALL KIND OF FABRIC REELS
MAXIMUM WORKING WIDTH: 2200mm
POWER INSTALLED: 4 Kw
VOLTAGE: 400V 50/60Hz
MAXIMUM ROLL DIAMETER: 250mm
MAXIMUM LOAD: 280kg
MAXIMUM SPEED: 20 M/MINUTE
DIMENSIONS: 3400 X 1200 X 1300mm
WEIGHT: 710kg

QUANTITY: 1

Learn More

REFERENCE NUMBER: R-5236

TYPE AND MODEL: L-818B
MAIN BODY BOX SIZE(M): 2.43X0.85X1.95
WEIGHING BOX SIZE(M): 1.6X0.57X1.05
FILLING PLATFORM(M): -
FILLING PORT: 2
DOWN STORAGEVOLUME(KG):12
CYCLE NUMBER: 3
WEIGHING RANGE(G): 0.2-32
ACCURACY GRADE(G): 0.01
FILLING SPEED(G/S): 5-8

QUANTITY: 1

Learn More

REFERENCE NUMBER: L-3203
MODEL: 2150
MACHINE EXTERNAL SIZE: 5000mm LONG X 2500mm WIDE X 2000mm HIGH
QUANTITY: 1

Learn More

P-5093 BUHLER ROASTER 60 KILOS

EVERY COFFEE MANUFACTURING APPLICATION REQUIRES INDIVIDUAL ROASTING PROCESSES FOR OPTIMIZED FLAVOR AND BEAN PROPERTIES. THIS ROASTER ADAPTS TO YOUR NEEDS AND OFFERS A MAXIMUM OF PROCESS FLEXIBILITY. IT INSPIRES YOUR PRODUCT INNOVATIONS WITH TRADITIONAL AND WITH MORE SOPHISTICATED MULTI-STEP ROASTING PROFILES. THE PROVEN DRUM ROASTING TECHNOLOGY OF THIS ROASTER ENSURES A RELIABLE, EFFICIENT AND SAFE ROASTING OPERATION.

THE OPTIMIZED DEGREE OF ROAST, THE ROASTING TIME AND THE ROASTING PROFILE MUST BE PRECISELY REPRODUCED FOR CONSISTENTLY HIGH QUALITY COFFEE PRODUCTS. THE MULTISTEP PROCESS OF THIS ROASTER ALLOWS FOR OPTIMIZED FLAVOR CREATION FOR ANY COFFEE BLEND AND VARIETIES AND ENSURES EXCELLENT CONSISTENCY. THE USER-FRIENDLY OPERATING PANEL INCLUDES A SIEMENS PLC AND A WINDOWS PANEL PC WITH 12.5 INCH TOUCH SCREEN FOR FULL PROCESS AUTOMATION AND EASY OPERATION.

FEATURES:
FULLY AUTOMATED ROASTING OPERATION
FULL RECIPE MANAGEMENT
AUTOMATED START AND STOP PROCEDURES
VARIOUS LOGIN-LEVELS FOR CUSTOMIZED ALLOCATION OF PERMISSION RIGHTS (OPERATOR, ENGINEER, ETC.)OPEN SYSTEM (NON-RECIRCULATION)
OPEN AIRFLOW SYSTEM
GAS / (DIESEL*) BURNER
DATA TRANSFER VIA ETHERNET (OPTION)
COOLING UNIT IN CONTROL CABINET (OPTION)
RECYCLE SYSTEM
RECIRCULATING AIRFLOW SYSTEM (UP TO 30% ENERGY SAVINGS COMPARED TO OPEN SYSTEMS)
GAS / (DIESEL*) BURNER
DATA TRANSFER VIA ETHERNET (OPTION)
COOLING UNIT IN CONTROL CABINET (OPTION)
HOT AIR SYSTEM: AIR RECIRCULATION OR NON-RECIRCULATING OPEN SYSTEM
HEAT GENERATION: FULLY VARIABLE LPG BURNER (WEISHAUPT) OR 2-STEP DIESEL BURNER
BATCH SIZE: 30 KG TO 60 KG (MAX. 70 KG/BATCH) HOURLY CAPACITY: UP TO 240 KG GREEN BEANS/HOUR
SERVICE CENTERS ARE IN SWITZERLAND, ITALY, USA AND INDIA
OPTIONAL FEATURES:
PNEUMATIC FEEDER
PNEUMATIC DESTONER/DISCHARGE UNIT
AFTERBURNER
NOTE: LOADER, DESTONER, AND AFTERBURNER WOULD COST EXTRA. PRICING AVAILABLE WITH QUOTE.

QUANTITY: 1

Learn More

H-1261 GOOSE FEATHER CLEANING MACHINE

LIST OF COMPONENTS FOR THE GOOSE FEATHER CLEANING MACHINE:

1) RINSING MACHINE OF THE TYPE 2000 (STAINLESS STEEL USED FOR IT)
EXTERIOR DIMENSION: 4000×2000×2600×Ф1800MM
QUANTITY: 1

2) GOOSE FEATHER ADDING MACHINE
EXTERIOR DIMENSION: 4000×1800×3300MM
QUANTITY: 1

3) WATER TANK
EXTERIOR DIMENSION: Ф1930MM×2440MM
QUANTITY: 1

4) DEWATERING MACHINE FLAT PLATE TYPE (BEING EQUIPPED WITH VARIABLE FREQUENCY CONTROL) - 2 SETS
QUANTITY: 2

5)DRYER OF THE TYPE 2000 (BEING EQUIPPED WITH ELECTRONIC WEIGHING)
EXTERIOR DIMENSION: 4500×2100×2900MM
QUANTITY: 1

6)GOOSE FEATHER ADDING MACHINE FOR DRYER(STAINLESS STEEL USED FOR IT AND ELECTRONIC WEIGHING INCLUDED)
EXTERIOR DIMENSION: 1500×1200×3600MM
QUANTITY: 1

7)THE COOLER OF THE TYPE 4700(STEEL & WOOD STRUCTURE, OPTIMIZED MOISTURE PROOF PANEL)
EXTERIOR DIMENSION: 4700×2350×2600×Ф2000MM
QUANTITY: 1

8) SORTING EQUIPMENT
QUANTITY: 2

9) POWER DISTRIBUTION CABINET
QUANTITY: 2

RINSING MACHINE: TYPE 2000

1. EXTERIOR DIMENSION: 4000×2000×2600×Ф1800MM DIAMETER

2.THE MATERIAL OF 14MM IN THICKNESS STAINLESS STEEL IS USED FOR THE WALL FOR WASHING MACHINE AND 5MM IN THICKNESS FOR BARREL

3. THE MATERIAL OF AISI 1045 IS USED FOR THE SPINDLE OF THE SQUARE SHAPE(SPECIFICATION =108MMX108MM). WRAPPED WITH 2MM STAINLESS STEEL IN THE OUTER.
10MM IN THICKNESS STAINLESS STEEL IS FOR HOOP OF VANE.
4MM IN THICKNESS STAINLESS STEEL WHICH IS FOLDED IS FOR VANE.
HOOP SCREW OF M14 X 70 (HIGH STRENGTH GRADE) ARE USED.
THE BEARING HOUSING &BEARING OF UKP318 IS USED FOR THE SPINDLE.

4.THE SIEVE OF 1.5MM IN THICKNESS STAINLESS STEEL IS USED FOR WACHING MACHINE.THE HOLE IS 1.8MM IN DIAMETER. HOLE SPACING 3.8MM .THE STAINLESS STEEL OF 2MM IS USED FOR THE OBLIQUE OF OUTPUTTING THE GOOSE FEATHER.THE OUTLET NEAR DEWATERING MACHINE FOR GOOSE FEATHER CAN BE TURNED UPWARD. FOR GOOSE FEATHER.

5.THE PIPE FOR WATER INLET IS 114MM IN DIAMETER

6.THE POWER OF FAN: 7.5KW AND SPEED: 2900R/M

7.THE PIPE FOR FEEDING GOOSE FEATHER IS 250MM IN DIAMETER.

8.THE REDUCER FOR THE SPINDLE: JZQ-400. THE POWER OF MOTOR IS 15KW AND OUTPUT SPEED IS 42 R/M

9.EXTERIOR DIMENSION OF THE BOTTOM FOR WASHING MACHINE: WIDTH=1600MM;LENGTH=3500MM.ONE SIEVE OF 1MM IN THICKNESS FOR IT.

WATER TANK

1. THE DIMENSION OF TANK: Ф1930MM×2440MM

2.THE STAINLESS STEELOF 2MM IN THICKNESS FOR ITS BARREL AND 3MM FOR THE BOTTOM.THE COVER IS CONSTUCTED WITH ANGLE IRON OF STAINLESS STEEL AND INNER COVER 2MM STAINLESS STEEL PLATE.

DEWATERING MACHINE OF TYPE 1600

1. ONE SETS OF RINSING MACHING OF THE TYPE 2000 IS EQUIPPED WITH TWO SETS DEWATERING MACHINE OF THE TYPE 1600

2.THE POWER OF MOTOR=11KW-17KW.DOUBLE SPEED MOTOR WITH VARIABLE FREQUENCY CONTROL.

DRYER OF TYPE 2000

1. EXTERIOR DIMENSION: 4500×2100×2900×Ф1800MM（DIAMETER）

2. THE MATERIAL OF 14MM IN THICKNESS STAINLESS STEEL(Q345R) IS USED FOR THE WALL FOR WASHING MACHINE. 10MM STAINLESS STEEL(Q345R) IS USED FOR INNER COVER OF THE BARREL AND 10MM STAINLESS STEEL (Q345R) PLATE FOR OUTER COVER OF THE BARREL.

3. THE INNER WALL OF WIND PLATE IS 0.5MM IN THICKNESS AND THE HOLE 1.5MM IN DIAMETER STAINLESS STEEL. 3MM COLD ROLLED PLATE IS USED FOR THE OUTER GATE.

4. THE SEAMLESS PIPE OF Ф108MM×10MM IS FOR THE MAIN SPINDLE.THE STEEL PLATE OF 10MM IN THICKNESS IS FOR THE VANE.THE WIDTH OF THE VANE IS 80MM. HOOP SCREW IS M12X70

6. THERE ARE FOUR INLET OF 1.5INCH IN DIAMETER FOR STEAM.
RELIEF VALVE FROM 3 KILO TO 7 (1 SETS)
THE PRESSURE GAGE (0-16 KILO) (2 SETS)
THE THERMOMETER (0-150 DEGREE) (1 SETS)
THERE ARE THREE DRAIN HOLE OF 1.5 INCH IN DIAMETER AT THE BOTTOM

6. THERE ARE TWO LAYERS FOR GOOSE FEATHER ADDING FOR DRYER: 1.5×1.2×3.6M.THEY ARE MADE WITH STAINLESS STEEL.THE SPECIFICATION OF CHARGING SPOUT ON THE TOP OF DRYER IS 1.55 X 0.55M.

7. THE OUTLET FOR GOOSE FEATHER OF DRYER CAN BE TURNED UPWARD.THE PIPE FOR OUTPUTTING GOOSE FEATHER IS 300MM IN DIAMETER.

8. TWO FANS ARE EQUIPPED FOR PRECISE WASHING LINE.THE POWER OF FAN FOR ADDING GOOSE FEATHER IS 7.5KW,SPEED: 2900R/M.WHICH IS USED TOGETHER WITH GOOSE ADDING MACHINE OF WASHING MACHINE.THE POWER OF FAN FOR DRYER IS 5.5KW,SPEED IS 2900 R/M.

9. MAIN SHAFT SPEED REDUCER FOR BELT BRIDGE MOTOR 7.5KW.OUTPUT SPEED IS 52 R/M
THE COOLER IS OF TYPE 4700

1. EXTERIOR DIMENSION: 4700×2350×2600×Ф2000MM DIAMETER

2. THE EXTERIOR IS CONSTRUCTED WITH THE WHOLE WOOD STRUCTURE.THE MATERIAL OF STEEL WITH 4# ANGLE STEEL AND 30X30 SQUARE TUBE IS FOR THE INNER SKELETON.

3. THE SEAMLESS PIPE OF Ф108MM×10MM IS FOR THE MAIN SPINDLE.THE STEEL PLATE OF 14MM IN THICKNESS IS FOR THE VANE.THE WIDTH OF THE VANE IS 80MM. HOOP SCREW IS M16X70

4. THE DIAMETER OF WIND PIPE: MAIN PIPE IS 300MM IN DIAMETER AND BRANCH IS 250MM IN DIAMETER.THERE ARE FOUR AIR OUTLET OF 300MM IN DIAMETER EQUIPPED EQUALLY SPACE.

5. ONE SIEVE IS EQUIPPED FOR THE COOLER.THE SIEVE IS MADE WITH 0.6MM IN THICKNESS GALVANIZED STEEL SHEET.THE HEIGHT OF HOLE IS 1.1MM.THE SCREEN FRAME IS MADE WITH 3# ANGLE STEEL.

6.THERE ARE TWO SORTING BOX WHICH IS CONSTRUCTED WITH STEEL FRAME AND WOODEN STRUCTURE. SIEVE 14 MESH GALVANIZED MESH BOLD

7. ONE FAN IS FOR THE COOLER.THE POWER OF THE FAN IS 11KW AND OUTPUT SPEED IS 2900 R/M

8. THE MOTOR FOR THE MAIN SPINDLE IS 15KW (6 POLE).THE SPEED OF 140 R/M IS FOR THE COOLER.

QUANTITY: 1

Learn More

REFERENCE NUMBER: F-1433

FEATHER FILLING MACHINE MODEL SR-4-A

 

MACHINE MODEL: SR-4-A

•              MAINLY USED TO FILL SLEEPING BAGS, CUSHIONS, PILLOWS, PADS, QUILTS, COMFORTERS ETC

•              DIMENSION: 700 x 600 x 1400MM

•              POWER: 1.6 KW

•              FILLING RANGE: 1 TO 100 G, DEPENDING ON THE MATERIAL

•              ACCURACY: 0 TO 8 G, +/-, DEPENDING ON THE OPERATION

•              WEIGHING AND FILLING WITH ONLY ONE MACHINE, IN ONLY ONE OPERATION,

RELIABLY AND PRECISELY

•              LOW NOISE BY USE OF A SPECIAL FAN FOR GENTLE FEATHER TRANSPORTATION AT EXTREMELY HIGH PERFORMANCE.

•              VARIABLE FILLING SPEED, QUICK-START AND QUICK-BRAKE OF THE FAN BY USE OF A

FREQUENCY INVERTER.

•              NICE DESIGN, ERGONOMIC AND SOPHISTICATED

•              EASY AND FAULTLESS OPERATION - LIGHT, BIG DISPLAY - BASED ON THE LATEST TECHNOLOGY.

•              START BY FOOT-SWITCH ON AND STOP BY FOOT-SWITCH OFF

Learn More