Search results for: 'Fabric cu''

REFERENCE NUMBER: M-5064 (121225HTJ11UX) L TSUDAKOMA WIDE WIDTH WATER JET WEAVING LOOMS FOR ACETATE YEAR 2006 WIDTH 3400mm TSUDAKOMA WATER JET LOOMS MANUFACTURING YEAR: 2006 WIDTH: 3400mm 2 WEFT FEEDERS CRANK SHEDDING 6 SHAFTS THESE LOOMS ARE SPECIAL EXECUTION OF TSUDAKOMA SPECIALLY PRODUCED FOR WIDE WIDTH WATER JET WEAVING SAMPLE WARP CAN BE SIZED FOR TRIAL AND CUSTOMER CAN SEE IT DURING RUNNING IF REQUESTED, 1 PIECE BEAM CAN ALSO BE SUPPLIED FOR ACETATE RUNNING NOW AT 450ppm AT 95% EFFICIENCY INCLUDES 1.5 PCS BEAM AND 1 PC REED QUANTITY AVAILABLE: 36 Learn More

REFERENCE NUMBER: A-1143 (1212GHBXX11) A SALVADE CURING/POLYMERIZER FOR PIGMENT PRINTING FIXATION YEAR 1995 WIDTH 3200mm POLYMERIZER MACHINE FOR PIGMENT PRINTING FIXATION YEAR: 1995 ROLLER WIDTH: 3400mm WORKING WIDTH: 3200mm FABRIC CONTENT: 300 METER IN LOOPS EXIT WITH BATCHER 380v 50hz INVERTER CONTROL PANEL QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-3014

GRIBETZ COMPUTERIZED QUILTING MACHINE-MODEL G.I.1200 (BEIGE COLOR)-86 INCH

 

QUILTING MACHINE

COMPUTERIZED

GRIBETZ

TYPE/MODEL: GI2000

MACHINE SIZES: 86”

NEEDLE SPACING: 1×3×6

MACHINE WIRED: 220V 3PH 60HZ

AUX. TRANSFORMER:  V- PH- HZ-

NOTE: THE QUILTER INCLUDES

(3) COMPLETE BARS

(1) CLOTH TRAY

(2) THREAD RACKS (ONE ON THE TOP AND THE OTHER ON THE BOTTOM)

(1) CATWALK

(1) TRANSFORMER

(2) CIRCULAR KNIVES

(27) LOOPERS

(2) SERVO MOTORS (TOSHIBA)

(1) FOAM RACK

(1) FABRIC COMPENSATOR

 

(1) SPUHL ANDERSON PANEL CUTTER

WITH (1) CROSSCUT BLADE

WITHOUT CIRCULAR KNIFE TO CUT BORDER

PLATE INFO:

MODEL: PC 8

 

(1) CONTROL PANEL WHICH HAS (4) DRIVES

FIRST DRIVE: INDUSTRIAL INDEXING SYSTEMS INC.

PART NR: AMP 4301

MODEL: RA DRIVER-RAD 02-2062

 

SECOND DRIVE: INDUSTRIAL INDEXING SYSTEMS INC.

PART NR: AMP 4300

MODEL: RA DRIVER-RAD 02-2062

 

THIRD DRIVE: INDUSTRIAL INDEXING SYSTEMS INC.

PART NR: AMP 4300

MODEL: RA DRIVER-RAD 02-2061

 

FOURTH DRIVE: INDUSTRIAL INDEXING SYSTEMS INC.

PART NR: MSC-850

 

NOTE: THE MACHINE HAS A NEMATRON-OPTI TOUCH

 

QUANTITY: 1

Learn More

REFERENCE NUMBER: M-3013 (770OIGFXX6)-D SPUHL ANDERSON PC6 PANEL CUTTER SPUHL ANDERSON PANEL CUTTER 95” MODEL PC6 YEAR OF PRODUCTION: CE 97 OPERATION VOLTAGE: 220 VAC CONTROL VOLTAGE: 110 VAC CONTROL VOLTAGE: 24 VDC TOTAL NOMINAL CURRENT: 10A MAIN SUPPLY FUSE: 25A FREQUENCY: 60HZ CONTROL VOLTAGE: 15VDC MAX. WORKING WIDTH: APPROX. 95” WITH (2) CIRCULAR BLADES TO TRIM THE EDGE AND WITH BLADE SHARPENERS WITH (14) CIRCULAR BLADES TO CUT BORDER AND WITH BLADE SHARPENERS (2) TAKE-OFF SHAFTS FOR CARDBOARD TUBES WITH FABRICS QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-3973 (99016AVEZ8RX)-D HOTMELT POWDER SCATTERING AND LAMINATING MACHINE-2200mm 1.LAMINATING LINE : MAKE : VILLARS (CH) ACTUALLY SANTEX YEAR: 1993 WORKING WIDTH : 2200mm (NOMINAL WIDTH 2M10) VOLTAGE: 3X380(400)V TOTAL POWER : 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION : INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997) : 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS : 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED 2.ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM : MAKE : MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR: 1999 OPERATING VOLTAGE : 3X380V CAPACITY ACCUMULATOR : +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) 3. SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE : MAKE: MENZEL YEAR: 2000 OPERATING VOLTAGE : 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT KNOWN PROBLEM : PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) 4.MISCELLANEOUS : SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS Learn More

BRUCKNER STENTER MODEL SPLITFLOW TWINAIR YOC 2002 Learn More

2 HEAD PANEL QUILTING MACHINE WITH AUTOMATIC FABRIC FEED Learn More

BRAND: STENTEX YEAR: 1995 WIDTH: 2400MM 12 CHAMBERS THERMIC OIL HEATED ENTRY WITH STENTEX BRAND TWO BOWL PADDER ENTERANCE WITH BIANCO CENTERING DEVICE OPERATOR PLAT FORM E<ANDEMATIC SENSOR WITH VERTICLE PIN CHAIN ENTRY TO 12 CHAMBERS EXIT WITH EDGE CUTTER AIR COOLING ZONE CYLINDER WITH WATER COOLING EXIT WITH SIMPLE PLAITER & A FRAME BATCHER EXCELLENT CONDITION Learn More

REFERENCE NUMBER: M-4749 (1111ASRPXX10) L RECYCLING PLANT FOR FABRIC CUTTING (1) X MONDEJAR CUTTING MACHINE MODEL CUTTEX 1000, YEAR 1992 (1) X CHUTE FEED FOR ACCUMULATION MATERIAL WITH VENTILATOR (1) X ROLANDO BIELLA ITALY TEARING MACHINE YEAR 1973, NR.6 DRUMS (PLUS 1 SPARE) WORKING WIDTH 1000mm AND ELECTRICAL PANEL COMPLETE WITH 1 ENZIMAGE (1) LLORPIC AUTOMATIC VERTICAL PRESS MODEL ALCOY, YEAR 1994 WITH CHUTE FEED FOR ACCUMULATION MATERIAL VENTILATOR AND ELECTRICAL BOX (4) X BONINO CARDS MODEL CC150/170 YEAR 1992, WITH BRIEST AND FIX FLATS BONINO CHUTE FEED (LIKE FBK533) EXIT CAN 40” X 48” WITH AUTOMATIC CHANGER QUANTITY AVAILABLE: 1 Learn More