Search results for: 'par'A=0'

REFERENCE NUMBER: M-5102 (1212FPDWXX11) L NEGATIVE & POSITIVE RAPIER HERCULES WEAVING MACHINES WIDTH 5500mm – FOR HEAVY FABRICS NEGATIVE & POSITIVE RAPIER HERCULES H5500 WEAVING MACHINES 20 SHAFTS NOMINAL WIDTH 5500mm MAXIMUM REED WIDTH 5500mm MINIMUM REED WIDTH 4400mm STANDARD BASIC MACHINE FOR VOLTAGE 440 V AND FREQUENCY OF 60 HZ DIRECT DRIVE MOTOR, SPEED CONTROLLED BY MICROPROCESSOR WITHOUT CHANGE OF PULLEY, WITHOUT CLUTCH SYSTEM, WITH (15%-40%) ELECTRIC POWER SAVING DEPENDING FROM TYPE OF WOVEN FABRIC SHEDDING MACHINE: STAUBLI DOBBY MODEL 2668 20 RODS SHAFTS TYPE GROB HEALD FRAME WITH UNDER MOTION 20 LEVER DRC CASTLE ELECTRIC CABINET WITH MICROPROCESSOR, ELECTRONIC PICK FINDING, ELECTRONIC LET-OFF, ELECTRONIC TAKE-UP UNIT WITH INDEPENDENT MOTOR ELECTRONIC WEFT COLOUR SELECTOR IN EXECUTION FOR 8 COLORS TAKE-UP WITH ROLLER DIAMETER 219mm 6 TWIN BEAM DIAMETER 219mm WITH FLANGE 1000mm Q3 JUMBO BACK REST BAR FOR HERCULES WEFT DENSITY VARIABLE PROGRAMMABLE BY THE OPERATOR AT YOUR CHOICE HORIZONTAL CREEL 4 COLOURS AND SUPPORT FOR 8 CONE 4 WEFT FEEDERS ROJ CHRONO X3 3 WEFT BRAKES FOR EVERY CHRONO X3 (TOTAL 12 PCS) TO BE SELECT AS PER CUSTOMER WEFT YARN WEFT CONTROLLING UNIT ELTEX MODEL G3W. DEROULÈ LATERAL MINI CREELS SUPPORT FOR 24 CONES LATERAL MOTORIZED LENO SYSTEM HEATING SCISSOR-CUTTING LATERAL TEMPLES: TO BE DEFINED DEPENDING THE FABRIC CHARACTERISTIC 20 FRAMES GROB TYPE 331 C TYPE DRC S227 GROBTEX ALFIX-U 14.000 GROB HEALDS TYPE 8 X 3.8 TYPE GROZ AETEX SP 0.38 331 8.0X3.8 I CR (7000PCS PER PACK) 1 WARP STOP MOTION 6-30 GROB FKW LED 14.000 GROB DROP WIRE TYPE GROZ EOU 1405 180X11X0.50 ZN (2000PCS PER PACK) SETS OF NEGATIVE RAPIERS & TAPE (LEFT AND RIGHT SIDE) SETS OF POSITIVE RAPIERS & TAPE (LEFT AND RIGHT SIDE) POSITIVE RAPIER KIT (FULL COMPONENT) CENTRAL GEARBOX ALREADY INSTALLED AND COLOR SELECTOR ALREADY ASSEMBLED FOR POSITIVE VERSION APPLICATION (TO REDUCE TIME OF CONVERSION) SETS AND EQUIPMENT OF LOOM TOOL CASE WITH TOTAL TOOLS LIKE TECHNICIANS INCLUDING NR. 2 TORQUE TOOL EXTRA SPARE PARTS THE TOTAL MACHINE SUPPLY WILL ALSO INCLUDE 2 SETS OF NEGATIVE RAPIERS (LEFT AND RIGHT SIDE) 2 SETS OF NEGATIVE TAPES (LEFT AND RIGHT SIDE) 2 SETS OF POSITIVE RAPIERS (LEFT AND RIGHT SIDE) 2 SETS OF POSITIVE TAPES (LEFT AND RIGHT SIDE) 1 POSITIVE RAPIER KIT (FULL COMPONENT) 1 SET AND EQUIPMENT OF LOOM 1 TOOL CASE WITH TOTAL TOOLS LIKE TECHNICIANS INCLUDE 2 TORQUE TOOLS EXTRA SPARE PARTS 1500EUR/MACHINE WARRANTY: ONE YEAR FROM MACHINE ERECTION OR AFTER 3 MONTHS DELIVERY DATE QUANTITY: 1 Learn More

REFERENCE NUMBER: A-1192 (1212GHBXX11) A PINTER UNITS WITH LYCRA ATTACHMENT PINTER UNITS WITH LYCRA ATTACHMENT 7 UNITS BLUE COLOR YEAR 2000 11 UNITS GREY COLOR YEAR 1995 UNITS ARE CURRENTLY INSTALLED ON RIETER G5/1 RING FRAMES 1008 SPINDLE EACH SALE INCLUDES ALL RELATED PINTER PARTS MANY NEW PARTS INCLUDING LYCRA ATTACHMENTS INSPECTION AND DELIVERY IMMEDIATE QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-3973 (99016AVEZ8RX)-D HOTMELT POWDER SCATTERING AND LAMINATING MACHINE-2200mm 1.LAMINATING LINE : MAKE : VILLARS (CH) ACTUALLY SANTEX YEAR: 1993 WORKING WIDTH : 2200mm (NOMINAL WIDTH 2M10) VOLTAGE: 3X380(400)V TOTAL POWER : 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION : INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997) : 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS : 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED 2.ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM : MAKE : MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR: 1999 OPERATING VOLTAGE : 3X380V CAPACITY ACCUMULATOR : +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) 3. SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE : MAKE: MENZEL YEAR: 2000 OPERATING VOLTAGE : 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT KNOWN PROBLEM : PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) 4.MISCELLANEOUS : SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS Learn More

BRUCKNER BOPP EXTRUSION LINE, WIDTH 8200mm, THREE LAYERS, BUILT 1992, COMPLETED WITH AN ATLAS SLITTER/REWINDER, MODEL CW, WIDTH 8200mm. AND FURTHER AUXILIARIES, INCLUDING SPARE PARTS. NAMEPLATE CAPACITY 20,000 T/Y. RAW MATERIALS SECTION - 4 SILOS 250 M3 ALUMINIUM - 2 SILOS 100 M3 ALUMINIUM - 2 SILOS 50 M3 ALUMINIUM - PNEUMATIC TRANSPORT SYSTEM; COMPUTERIZED DOSING SYSTEM, HOPPERS AND SCALES FOR THE THREE EXTRUDERS EXTRUSION SECTION - MAIN EXTRUDERS: 2 MITSUBISHI CASCADE EXTRUDERS Ø 300 mm AND 250 mm - CO-EXTRUDERS: 2 BANDERA EXTRUDERS Ø 100 mm, EQUIPPED WITH MELT PIPES - DIE: SIMPLAST, WIDTH 1,140 mm, GAP 2 - 3.75 mm, 40 PUSH/PULL BOLTS - CHILL ROLL: Ø 3 M, 1,900,000 KJ/H COOLING CAPACITY - WATER BATH: 1.500.000 KJ/H CAPACITY MDO (MACHINE DIRECTION ORIENTATION) SECTION - PREHEATING INFRARED 130 KW - PREHEATING: 16 CHROMIUM PLATED ROLLS Ø 614 mm - STRETCHING: 6 CHROMIUM PLATED ROLLS Ø 180 mm, EQUIPPED WITH RUBBER NIP ROLLS Ø 150 mm - ANNEALING: 2 CHROMIUM PLATED ROLLS Ø 614 mm TDO (TRANSVERSE DIRECTION ORIENTATION) SECTION - TOTAL LENGTH: 66 METER - PREHEATING: 5 SECTIONS - STRETCHING : 5 SECTIONS - ANNEALING : 5 SECTIONS - NEUTRAL : 1 SECTION - COOLING : 2 SECTIONS - INLET 850 – 1,050 mm WIDTH - OUTLET 7,600 – 8,600 mm WIDTH PRS (PULL ROLL STAND) SECTION - EDGE TRIM CUTTERS - ESSECI FLAME TREATER, BURNER, CHROMIUM PLATE ROLL, RUBBER NIP ROLL - CORONA TREATER 1: 3 DISCHARGE BARS, SILICON ROLL, RUBBER NIP ROLL - CORONA TREATER 2: 2 DISCHARGE BARS, EDGE BAR, SILICON ROLL, RUNNER NIP ROLL MEASUREX/HONEYWELL GAUGE CONTROL SYSTEMS - 8.5 M SCANNER FOR FILM - 1.2 M SCANNER FOR CAST SHEET - MAIN THICKNESS CONTROL UNIT CONNECTED TO THE BOLT OF THE EXTRUSION DIE FOR LIP ADJUSTMENT WINDER - 2 TURRETS KAMPF WINDER - AUTOMATIC CUT / TURRET / MILL-ROLL CHANGE - WINDING CORES: 108 STEEL WINDING CORES Ø 500 mm CONTROL UNIT - THE LINE IS EQUIPPED WITH A FULLY INTEGRATED CONTROL SYSTEM SUPPLIED BY BRUCKNER MILL ROLL STAND (SEMI-FINISHED PRODUCTS WAREHOUSE) - 150 TOTAL POSITIONS, OF WHICH 50 IN HEATED CLOSED ROOM - 1 PICK-UP FOR LOADING / UNLOADING WINDER AND SLITTER - 1 MANUAL EMERGENCY PICK-UP FOR LOADING/UNLOADING WI NDER AND SLITTER AND MAINTENANCE - 1 SHUTTLE TO MOVE MILL ROLLS IN AND OUT OF THE WAREHOUSE - 1 MAIN CRANE FOR MOVING MILL ROLLS / EMPTY CORES RECYCLING - HERBOLD GRINDER FOR SCRAP RECOVERY - 4 FLUFF SILOS - 1 EREMA MACHINE FOR REGRANULATION, APPROX. 700 KG/H SLITTER - ATLAS CW MACHINE, BUILT 1992, MAJOR UPGRADE 2010 - INLET MILL-ROLLS MAX Ø 1.2 M, WIDTH 8.2 M - 16 REWINDING STATIONS, WIDTHS FROM 400 mm TO 2450 mm, MAX Ø 1,000 mm - AUTOMATIC KNIVES AND RE-WINDING ARMS POSITIONING PACKING - SEMI-AUTOMATIC BALLOTTI LINE FOR CONDITIONING OF ROLLS AND PALLETS, BUILT 2000 - CONVEYORS - SCALING - STRAPPING - STRETCHING UTILITIES - 3 COMPRESSORS 3 BARS FOR COMPRESSED AIR CIRCUIT FOR RAW MATERIALS HANDLING - 2 COMPRESSORS 6 BARS FOR COMPRESSED AIR - 2 CHILLERS FOR CHILLED WATER PRODUCTION - 2 WATER COOLING TOWERS - 1 BOILER FOR THERMAL OIL PRODUCTION - 3 TRANSFORMERS 15 KV TO 380 V ADDITIONAL EQUIPMENT - SPARE PARTS FOR ALL OF THE ABOVE - TECHNICAL CONSUMABLES - IT EQUIPMENT FOR CONTROLLING THE MANUFACTURING EQUIPMENT AND DATA TRAFFIC, SUCH AS SERVERS, SWITCHES AND CABLING - LABORATORY EQUIPMENT FOR QUALITY CONTROL PURPOSES Line was producing 20 to 40 microns , line can produce down to 10 to 12 microns Learn More

REFERENCE NUMBER: M-4441 (1010HYGAHH9) K EXTRUSION LINES TYPE STM 16 BCF FOR THE PRODUCTION OF CARPET YARN YEAR 1991-1994 1 MACHINE YEAR 1991 1 MACHINE YEAR 1994 TEXTURIZING IS BARMAG JETS ONE LINE IS 3-COLOR OTHER LINE IS 4- COLOR ALSO INCLUDED: SPINNING PACKS (1 SET PLUS SPARE SET OF SPINNERETS), 132 FILAMENTS TRILOBAL SPARE WINDER WITH TEX JETS, ELECTRONIC PARTS AND MECHANICAL PARTS COOL SYSTEM WITH CHILLER ONE OVEN ONLY (FOR PREHEATING) QUANTITY AVAILABLE: 2 Learn More

TT-7849 JENBACHER JGS 620F GENERATOR SYSTEM, 6.712 MW TOTAL, 11KV, 20K/23K HOURS, NATURAL GAS, 2012 1. USED JENBACHER GENERATOR SYSTEM 2. CONSISTING OF (2) MODEL JGS 620F JENBACHER NATURAL GAS GENSETS 3. EACH RATED 3.356 MW; 2.9 MW NET OUTPUT; 1500 RPM; 3/50/11KV 4. YEAR BUILT 2012 5. REPORTED 20,000 HOURS AND 23,000 HOURS. CONTROLLED BY (1) PANEL. 6. BRAND: JENBACHER 7. MODEL: JGS 620F 8. USED EQUIPMENT FACTS ABOUT THIS MACHINE 9. FUEL TYPE: NATURAL GAS QUANTITY: 1 Learn More

TT-7562 CATERPILLAR 816B, YEAR 1989, RECONDITIONED, 17,330 HOURS 1. MACHINE HOURS: 17,330 2. CATERPILLAR DEALER REBUILT THE COMPLETE DRIVE TRAIN AT 15,384 HOURS 3. ENGINE, TORQUE, TRANSMISSION, TRANSFER CASE, BOTH DIFFERENTIALS, 4. ALL FINAL DRIVES, REAR AXLE OSCILLATION & HYDRAULIC PUMPS ETC. 5. REBUILD / REPAIR RECORDS ARE AVAILABLE. 6. ALL NEEDED REPAIRS & SERVICING HAS BEEN COMPLETED BY MARCEL EQUIPMENT SINCE ARRIVING IN OUR YARD. QUANTITY: 1 Learn More

CLOSED TYPE WITH SMALL AIR-CONDITIONER (2) COMPUTER AND FILLING SETS RUN BY TWO OPERATORS DIAMETER OF FILLING NOZZLE: 12mm FILLING WEIGHT ≤2 GRAM, FILLING TIME ≤1 SECOND AN AIR COMPRESSOR (THREE-PHASE WITH 5.5KW) AND AN AIR STORAGE TANK (0.6 TO 1 M³) ARE NEEDED THE CAPACITY OF THE COMPRESSED AIR CAN BE USED BY (12) SETS OF FILLING NOZZLES (SIX FILLING MACHINES) DIAMETER OF COMPRESSED AIR PIPE: 1” (FROM AIR STORAGE TANK TO FILLING ROOM) DIAMETER OF COMPRESSED AIR PIPE: ½” (MAIN MACHINE TO FILLING NOZZLE) VOLTAGE: 220V POWER: AIR-CONDITION 500W, AIR-CIRCULATION FAN 370W, FILLING FAN 180W, VARIABLE SPEED MOTOR 200W, LIGHTS 60W AND COMPUTER 50W AIR PRESSURE: 6MPa FLOOR SPACE OF FILLING ROOM: ≥6M² FILLING ERROR RANGE: 1 GRAM FOR ONE PIECE DOWN CONTENT: 50% TO 95% STAINLESS STEEL MAIN FRAME TOUCH SCREEN WITH (1) PRECISE WEIGHING SCALE WITH AIR CIRCULATION SYSTEM AUTOMATICLLY RECYCLE FEATHERS THAT FALL TO THE FLOOR MOVABLE FILLING MACHINE CAN BE DISMOUNTED WITH SPOTLIGHT (2) WORKING TABLE DIMENSIONS OF THE MACHINE: 3000 X 1300 X 1800 (mm) Learn More

REFERENCE NUMBER: K-1782 AUTOMATIC BAGGING LINE MOD. EASY BAG - WITHOUT LEAFLET INSERTION DESCRIPTION: THIS IS AN AUTOMATIC LINE COMPLETE WITH ROBOTIC MACHINES SPECIFICALLY FOR FILLING PILLOWS AND CUSHIONS INTO PLASTIC BAGS WITH PRESS AND WELDING SYSTEM WITH BAGGED CUSHIONS AUTOMATIC OUTPUT. QUANTITY AVAILABLE: 1 Learn More