Search results for: 'air+inde'

REFERENCE NUMBER: M-3349 (88013DYN7U)-D TOYOTA AIRJET LOOMS TOYOTA AIR JET LOOM QTY MODEL=JA2S-190TP-T610 TOTAL 60 LOOMS 60 STAUBLI POSITIVE TAPPET CAM MOPTION TYPE 1620 CAM BOX WITH 7 SHAFT 6 CAMS WITH 1 SPACER FOR EACH LOOM 60SETS 1 REPEAT GEAR FOR EACH LOOM 60SETS PROFILE REED SYSTEM REED SPACE 190 CM 60 LOWER BUILT ONE PIECE BOX TYPE SIDE FRAME FOR HIGH SPEED OPERATION 60 OIL BATH LUBRICATION FOR MAIN UNITS 60 TWO SIDES CRANK DRIVE BEATING WITH OIL BATH 60 HIGH TORQE INDUCTION MOTOR WITH SOLENOID BRAKE (4P-3PHASE,3.5KW) 60 MAIN CONTROL COMPUTER WITH 32 BYTES CPU 60 DISTRIBUTED CONTROL SYSTEM BY OPTICAL FIBER COMMUNICATION NETWORK 60 TOUCH SCREEN FUNCTION PANEL WITH MULTI- WINDOW DISPLAY 60 AUTOMATIC INITIAL CONDITION - (ICS) SYSTEM 60 AUTOMATIC FAULT ALRAM FUNCTION 60 WEEKLY EFFICIENCY GRAPH DISPLAY & DOWN TIME 60 CAUSE DISLPAY BEAM CLOTH ESTIMATOR 60 2 COLOUR MIXING DEVICE BY ELECTRIC DRUM POLE (EDP) 60 TAPERED SUB NOZZLE 60 LOW AIR PRESURE & HIGH PROPULSIVE MAIN NOZZLE 60 DIRECT DRIVE SOLENOID VALVE FOR MAIN & SUB NOZZLE 60 TWO INDEPENDENT SUB NOZZLE TANKS 60 TAPERED TUNNEL REED 60 AUTOMATIC TIMING CONTROLLER (ATC) 60 AUTOMATIC BRAKE SYSTEM (ABS) 60 TIMING CHEKER WITH GRAPH DISPLAY ON FUNCTION PANEL 60 CENTRALIZED REGULATOR 60 ELECTRONIC LET OFF MOTION BY DIGITAL AC SERVO MOTOR 60 AUTOMATIC LET OFF ADJUSTMENT 60 FELL FORWARD DEVICE FOR STOP MARK PREVENTION 60 POSITIVE EASING MOTION WITH TWIN BACK ROLLER 60 MECHANICAL TAKE UP MOTION BY CHANGE GEAR 60 ON LOOM TAKE UP MOTION FOR MAXIMUM -600MM CLOTH DIA 60 DOUBLE PRESS CLOTH ROLLS 60LOOM METAL SPRAYED SURFACE TAKE UP ROOLER 60 RING TAMPLE-3ROWS -24RING 60SET ROTARY LENO SELVEDGE AT L+R SIDE WITH ELECTRIC STOP MOTION 60SET DOUBLE FEELER FOR WEFT STOP MOTION -(REFLECTING TYPE ) 60 ELECTRIC WARP STOP MOTION BY SIX LINES CONTACT BAR 6 PER LOOM YARN BEAM SET WITH 1000 MM FLANGE & 178 MM BAREL DIA 90 CLOTH ROLLER 100 MM DIA 90 REED 60PIECE HEALD FRAMES 7 PER LOOM HEALD WIRE (331MML) C TYPE 6000PER LOOM DROPPER- (165-11-0.3) 6000PER LOOM QUANTITY: 60 TOYOTA AIR JET LOOM QTY MODEL=JA2S-280TP-T610 TOTAL 12 LOOM. 12 STAUBLI POSITIVE TAPPET CAM MOPTION 12SETS TYPE 1620 CAM BOX WITH 7 SHAFT 6 CAMS WITH 1 SPACER FOR EACH LOOM 12SETS 1 REPEAT GEAR FOR EACH LOOM 12SETS PROFILE REED SYSTEM REED SPACE 280 CM 12 LOWER BUILT ONE PIECE BOX TYPE SIDE FRAME FOR HIGH SPEED OPERATION 12 OIL BATH LUBRICATION FOR MAIN UNIT 12 TWO SIDES CRANK DRIVE BEATING WITH OIL BATH 12 HIGH TORQE INDUCTION MOTOR WITH SOLENOID 12 BRAKE (4P-3PHASE,3.5KW) MAIN CONTROL COMPUTER WITH 32 BYTES CPU 12 DISTRIBUTED CONTROL SYSTEM BY OPTICAL FIBER 12 COMMUNICATION NETWORK TOUCH SCREEN FUNCTION PANEL WITH MULTI- WINDOW DISPLAY 12 AUTOMATIC INITIAL CONDITION - (ICS) SYSTEM AUTOMATIC FAULT ALRAM FUNCTION 12 WEEKLY EFFICIENCY GRAPH DISPLAY & DOWN TIME 12 CAUSE DISLPAY BEAM CLOTH ESTIMATOR 12 2 COLOUR MIXING DEVICE BY ELECTRIC DRUM POLE (EDP) 12 TAPERED SUB NOZZLE 12 LOW AIR PRESURE & HIGH PROPULSIVE MAIN NOZZLE 12 DIRECT DRIVE SOLENIOD VALVE FOR MAIN & SUB NOZZLE 12 TWO INDEPENDENT SUB NOZZLE TANKS 12 TAPERED TUNNEL REED 12 AUTOMATIC TIMING CONTROL (ATC) 12 AUTOMATIC BRAKE SYSTEM (ABS) 12 TIMING CHEKER WITH GRAPH DISPLAY ON FUNCTION PANEL 12 CENTRALIZED REGULATOR 12 ELECTRONIC LET OFF MOTION BY DIGITAL AC SERVO MOTOR 12 AUTOMATIC LET OFF ADJUSTMENT 12 FELL FORWARD DEVICE FOR STOP MARK PREVENTION 12 POSITIVE EASING MOTION WITH TWIN BACK ROLLER 12 MECHANICAL TAKE UP MOTION BY CHANGE GEAR 12 ON LOOM TAKE UP MOTION FOR MAXIMUM -600MMCLOTH DIA 12 DOUBLE PRESS CLOTH ROLLS 12LOOM METAL SPRAYED SURFASE TAKE UP ROOLER 12 RING TAMPLE-3ROW -30RING 12SET OCCUPIED WITH TUCK IN DEVICE WITH COMPLETE ACCESSORIES DOUBLE FEELER FOR WEFT STOP MOTION -(REFLECTING TYPE ) ELECTRIC WARP STOP MOTION BY SIX LINES CONTACT BAR 6PER LOOM YARN BEAM SET WITH 1000 MM FLANGE & 178 MM BARREL DIA 18 CLOTH ROLLER 100 MM DIA 18 REED 12PIECE HEALD FRAMES 7 PER LOOM HEALD WIRE (331MML) C TYPE 8000PER LOOM DROPPER- (165-11-0.3) 8000PER LOOM QUANTITY AVAILABLE: 12 LOOMS 20 LOOMS HAVE GEAR FOR TUCK IN DEVICE, GEAR BOX AT LEFT SIDE 1 INVERTER FOR 36 LOOMS ( 2 INVERTERS FOR ALL 72) 2 ATLAS COPCO ZR-315 COMPRESORS AND DRYER MD-1000 AVAILALE AT ADDITIONAL COST Learn More

YY-2761 SLOT DIE COATING MACHINE, WORKING WIDTH 1550mm, FOR HOT MELT PRESSURE SENSITIVE ADHESIVE COATING AND LAMINATION APPLICATION: 1. HOT MELT SENSITIVE PRESSURE ADHESIVE COATING AND LAMINATION LINE, IT HAS FUNCTIONS OF COATING, LAMINATION, PEELING, REWINDING FUNCTION. 2. MATERIAL APPLICATION: PET, PVC, PAPER ETC. QUANTITY: 1 Learn More

YY-2409 SLOT DIE COATING MACHINE, MAXIMUM COATING WIDTH 1550mm (61 INCHES) APPLICATION: 1. HOT MELT SENSITIVE PRESSURE ADHESIVE COATING AND LAMINATION LINE, FOR COATING, LAMINATION, PEELING, REWINDING FUNCTION. 2. APPLICATION MATERIAL: PET, PVC, PAPER ETC. MACHINE FEATURES: 1. THIS MACHINE INCLUDES MICROCOMPUTER PLC, TOUCH SCREEN CONTROL, SIMPLE OPERATION AND HIGH AUTOMATION; 2. USING HIGH WEAR-RESISTANT ALLOY STEEL SLOT DIE, WITH COATING CONTROL ACCURACY AND GOOD SERVICE LIFE; 3. AN OVERALL COATING ADJUSTMENT BRACKET IS INCLUDED, AND THE REPEAT POSITIONING ACCURACY IS PRECISE; 4. AUTOMATICALLY TRACKS AND DISPLAYS AND STORES THE AMOUNT OF GLUE NEEDED, MAKING THE OPERATION AND USE CONVENIENT AND FAST; 5. THE FIRST UNWINDING IS EQUIPPED WITH A WEB GUIDING DEVICE, WITH A HIGH-PERFORMANCE INFRARED SENSOR AND ELECTRIC CONTROLLER TO ENSURE THE EVEN LET OFF OF THE MATERIAL ROLL; 6. THE HEATING TEMPERATURE IS ALL CENTRALLY CONTROLLED BY PLC; 7. THE AMOUNT OF GLUE SUPPLIED BY THE METERING PUMP FOR THE COATING WIDTH IS INPUT BY THE WORKER, AND THE AMOUNT OF GLUE SUPPLIED WILL BE AUTOMATICALLY CALCULATED AND SUPPLIED TO THE DIE SLOT. QUANTITY: 1 Learn More

REFERENCE NUMBER: T-6552

MASK AIR TIGHTNESS TESTER

 

MASK AIR TIGHTNESS TESTER

HOW TO CHOOSE A HIGH-QUALITY MASK NOT ONLY DEPENDS ON THE FILTERING EFFICIENCY OF THEMASK, BUT ALSO TO CONFIRM WHETHER THE MASK IS COMPLETELY IN CONTACT WITH THE FACE, OTHERWISE AEROSOL PARTICLES SUCH AS GERMS THAT HAVE NOT BEEN FILTERED BY THE MASK WILL BE INHALED FROM THE INADEQUATE ADHESION. THEREFORE, IT IS VERY IMPORTANT TO CHECK THE WEARING STATUS OF THE MASK. THE EUROPEAN AND AMERICAN COUNTRIES HAVE LISTED THE APPLICATION TEST OF THE MASK AS A STRONG INSPECTION ITEM.

FOR EXAMPLE, THE N95 MASK IS ONE OF 9 TYPES OF PARTICULATE PROTECTIVE MASKS CERTIFIED BY NIOSH (NATIONAL INSTITUTE OF OCCUPATIONAL SAFETY AND HEALTH). "N" INDICATES OIL RESISTANCE."95" INDICATES THAT THE PARTICLE CONCENTRATION IN THE MASK IS MORE THAN 95% LOWER THAN THAT OF THE PARTICLES OUTSIDE THE MASK WHEN EXPOSED TO THE SPECIFIED NUMBER OF SPECIAL TEST PARTICLES. N95 IS NOT A SPECIFIC PRODUCT NAME, AS LONG AS IT MEETS THE N95 STANDARD AND PASSES THE NIOSH REVIEW, IT CAN BE CALLED "N95 MASK".

N95 TYPE MASKS, IN ADDITION TO THE FILTERING EFFICIENCY OF THE MASKS, THE CLOSENESS OF THE MASKS TO THE FACE IS ONE OF THE IMPORTANT FACTORS THAT DETERMINE THE EFFECTIVENESS OF THE USE OF THE MASKS. THE SUITABILITY OF DIFFERENT TYPES OF MASKS FOR THE HUMAN FACE VARIES GREATLY.

THEREFORE, BEFORE USING A MASK, THE SUITABILITY OF THE MASK SHOULD BE CHECKED FIRST. DURING THETIGHTNESS TEST OF THE WEARER'S FACE, ENSURE THAT AIR CAN PASS IN AND OUT THROUGH THE MASK WHEN IT IS CLOSE TO THE EDGE OF THE FACE. THE MASK TIGHTNESS TESTER CAN QUICKLY COMPLETE THE TIGHTNESS TEST OF RESPIRATORS SUCH AS MASKS TO ENSURE THAT IT PROVIDES GOOD PROTECTION PERFORMANCE. IT CONFORMS TO THE CHINESE RESPIRATOR STANDARD GB2626-2019 STANDARD, OSHA / CSA STANDARD AND CHINA GENERAL ADMINISTRATION OF QUALITY SUPERVISION, INSPECTION AND QUARANTINE "GB 19083-2010 TECHNICAL REQUIREMENTS FOR MEDICAL PROTECTIVE MASKS" JOINTLY ISSUED BY THE CHINA NATIONAL STANDARDIZATION ADMINISTRATION COMMITTEE.

ADHESION (SUITABILITY TEST): THE MASK DESIGN SHOULD PROVIDE GOOD ADHESION. THE OVERALL FIT FACTOR OF THE MASK SHOULD NOT BE LESS THAN 100. THIS TEST THE REQUIREMENTS WERE FORMALLY IMPLEMENTED ON AUGUST 1, 2011.

Learn More

H-1305 BATT FEEDING SYSTEM - WORKING WIDTH 3000mm

WORKING WIDTH: 3000mm
CONTROL SYSTEM INCLUDED

COMPOSITION OF THE MACHINE:
- LOWER PVC INCLINED CONVEYOR BELT FOR THE TRANSPORT OF THE WEB FROM THE CROSS LAPPER TO THE ENTRANCE OF THE NEEDLE LOOM.
- UPPER PVC COMPRESSION BELT FOR THE PRE-COMPRESSION OF THE WEB BEFORE ENTERING THE FEEDING ROLLS.
- LOWER PVC CONVEYOR AND UPPER PVC BELT DRIVEN BY ONE GEARBOX MOTOR WITH INDEPENDENT FREQUENCY INVERTER.
- PAIR OF FEEDING ROLLS WITH PLASTIC FINGERS TO GUIDE THE COMPRESSED WEB CLOSE TO FIRST NEEDLE ZONE OF THE PRE-NEEDLE LOOM. ROLLER PAIR DRIVEN BY GEARBOX MOTOR WITH INDEPENDENT FREQUENCY INVERTER.
- BATT FEEDING SYSTEM INSTALLED ON RAIL SYSTEM AND EASY REMOVABLE FOR MAINTENANCE OF THE NEEDLE LOOM

TECHNICAL DATA:
ELECTRICAL INFORMATION:
ELECTRIC: MAIN VOLTAGE 400 V, 50 HZ, 3 PH.
CONTROL VOLTAGE: DC - 24 V / AC - 230 V
OTHER INFORMATION:
AIR PRESSURE (CONSTANT): MIN. 6 BAR (AT SITE)
OPERATOR SIDE LEFT OR RIGHT (IN WEB RUNNING DIRECTION)
LACQUER COATING:
MAIN COLOR OF THE MACHINES: RAL 7035 (LIGHT GREY)
CONTROL CABINET AND CONTROL DESK RAL 7035 (LIGHT GREY)
LABELING: ENGLISH
TECHNICAL DOCUMENTATION: ONE TIME ON CD-ROM (FURTHER SETS AVAILABLE AT ADDITIONAL COST)
LANGUAGE FOR OPERATING INSTRUCTIONS: ENGLISH
LANGUAGE FOR FURTHER DOCUMENTATION (SPARE PART LISTS, WIRING DIAGRAM, ETC): ENGLISH

ENVIRONMENTAL CONDITIONS:
INSTALLATION HEIGHT ABOVE SEA LEVEL: LESS THAN OR EQUAL TO 1,000 METERS
TEMPERATURE: 24° C (±2° C)
RELATIVE HUMIDITY: 65% (±5%)
ABSOLUTE WATER CONTENT: 9 TO 12 G/KG DRY AIR
NOTE: PLEASE MAKE SURE THAT THE TEMPERATURE INSIDE THE CONTROL CABINET DOES NOT EXCEED 450 CENTIGRADE. IN CASE OF EXCESSIVE ROOM TEMPERATURES WE RECOMMEND AN AIR-CONDITIONING SYSTEM FOR THE CONTROL CABINETS TO AVOID MALFUNCTION OF ELECTRICAL COMPONENTS

QUANTITY: 1

Learn More

TT-7787 WARTSILA POWER PLANT, 169 MW, 60Hz, YEAR 2010 1. WARTSILA POWER PLANT 2. COMMERCIAL OPERATION START: JANUARY 2010 3. CONTRACT STATUS: OPERATED UNDER STANDBY MODE UNTIL DECEMBER 2024 4. 20 X WARTSILA 20V32 5. 8.45MW EACH, 60Hz 6. HFO, BUT CONVERTIBLE TO DIESEL OR BIODIESEL. GREEN. VERY GOOD CONDITION Learn More

YY-1347 PSA OXYGEN GENERATION SYSTEM SCHEME, CAPACITY 50 m3 PER HOUR PURITY: ≥ 93%, FLOW RATE: 50M3 PER H, (PRESSURE: 200 BAR AUTOMATIC FILLING SYSTEM) Learn More

YY-1348 PSA OXYGEN GENERATION SYSTEM SCHEME, FLOW RATE 100 M3 PER HOUR DETAILS: PURITY: ≥ 93%, FLOW RATE: 100 M3 / H, (PRESSURE: 200 BAR AUTOMATIC FILLING SYSTEM) QUANTITY: 1 Learn More

A-2570 TUBE FILLING SEALING MACHINE 3.4 KW SEALING TYPE: HEATING (PLASTIC), FOLDING (ALUMINUM) MAX POWER: 2.0 TO 3.3 KW (PLASTIC), 1.5 KW (ALUMINUM) VOLTAGE: 220 VOLTZ AND 50/60 Hz PRODUCTIVITY: 20 TO 30 PCS/Min FILLING VOLUME: 8 TO 250 ML (CHANGE PUMP) TUBE DIAMETER: 10 TO 50 mm (CHANGE MOLDS) TUBE LENGTH: 50 TO 200 mm (CUSTOMIZED) HOPPER CAPACITY: 40 L FILLING ACCURACY: ≤±1% CONTROL: PLC CONTROL SYSTEM DISPLAY: TOUCH SCREEN DISPLAY FEATURE: NO TUBE NO FILLING DIMENSION (L X W X H): 1000 X 800 X 1600 mm WEIGHT: ABOUT 600 KG Learn More

P-5044 STA IMPIANTI ROASTER 5 KILOS

STA
MODEL: IMPIANTI
ROASTER
5 KILOS
STA IS A MANUFACTURING GROUP IN ITALY - THAT IS MADE UP OF SEASONED ENGINEERS FROM MOST OF THE BIG OLD ITALIAN ROASTING MACHINE MAKERS - SO THEIR SCOPE OF KNOWLEDGE AND HISTORY IS FANTASTIC. BASICALLY - THEIR CLAIM TO FAME IS HOT AIR INTRODUCED INTO THE TOP OF THE ROASTING CHAMBER . . . BEING PULLED THROUGH THE TURBULATING COFFEE AND EXITING THROUGH DRUM PERFORATIONS INTO THE BOTTOM. FIRST, THAT MAKES IT REALLY FRIENDLY TO BLENDING FORMULAS AND SECOND IT MAKES FOR SMALLER CHAFF - AS THE TURNING COFFEE BEATS IT UP A LITTLE AND THUS THE ROAST COMES OUT MORE CLEAN THAN THE OLD DAYS OF SOME SOLID DRUMS . . . SO IT IS DIFFERENT - WHICH DOES NOT MAKE IT BETTER - BUT IF YOU HAVE A BACKGROUND ON JABEZ BURNS . . THEN YOU WILL REALLY LOVE THIS PRODUCTION. BIG NATURALLY DEVELOPED BEANS - VERY EVEN ROAST. FOLLOWING IS THE MANUFACTURERS SPECS AND WE WILL BE GLAD TO DISCUSS MORE IN-DEPTH AS YOU HAVE QUESTIONS.

ROASTING MACHINES LINE, PARTICULARLY SUITABLE FOR LITTLE PRODUCTION ACTIVITIES OF HIGH QUALITY ROASTED COFFEE, SUCH AS SHOPS, PASTRIES OR ARTISAN LABORATORIES. SMALL SIZE, TECHNOLOGICALLY ADVANCED, CONFIRM THEM ELVES AS IDEAL TOOL FOR THE PRODUCTION OF SELECTED COFFEES IN LITTLE QUANTITY. MADE WITH THE SAME REQUIREMENTS FOR RELIABILITY AND SECURITY FEATURES OF THE BIGGER AND MORE SOPHISTICATED INDUSTRIAL ROASTING MACHINES, ARE AVAILABLE WITH HEATING GENERATOR TYPE GAS BURNER (AVAILABLE ALSO BY ELECTRIC RESISTANCES) AND AUTOMATIC CONTROL SYSTEM WITH SEMIAUTOMATIC MANAGEMENT.

TECHNICAL DATA:
ROASTER CAPACITY: 5 KG. - MAX. 7 KG. CYCLE
ROASTING CYCLE: 9 MINUTES ÷ 20
RAW COFFEE PROCESSING PER HOUR: 20 KG. ÷ 30
INSTALLED ELECTRIC POWER: 0.9 KW | SINGLEPHASE 220 VOLTS 50 HZ
THERMAL POWER (NATURAL GAS OR LPG): 8000 KCAL/H
MAIN COMPONENTS:
HOPPER OF CHARGE IN STAINLESS STEEL
ROASTING DRUM
HEATING GENERATOR OF NEW GENERATION, PATENTED AND COMPLETE OF BURNER
RAMP VALVES FOR GAS SAFETY AND ELECTRIC DEVICE TO CHECK FLAMES RATIFIED AND COMPLETE OF ALARM SIGNAL
COOLING TANK IN STAINLESS STEEL
SAFETY PREVENTION SYSTEM ON THE COOLING TANK
SUPPORTING FRAME FOR THE OVER INDICATED COMPONENTS
ELECTRIC CONTROL BOARD MADE ACCORDING CE RULES, INTEGRATED, COMPLETE OF PLC + TOUCH SCREEN DEVICE FOR ROASTING MACHINE CONTROL AND MANAGEMENT.
INDEPENDENT FANS FOR THE ROASTING DRUM AND THE COOLING TANK
INDEPENDENT MOTORS FOR THE ROASTING DRUM AND THE COOLING TANK
CYCLONE FOR CHAFFS COLLECTING
DETAILS OF COMPONENTS:
HOPPER OF CHARGE IN STAINLESS STEEL WITH MANUAL IN-LET OF COFFEE WITH DOORUNLOADING SYSTEM.
ROASTING DRUM: MADE BY A FIXED ELEMENT WITH DOUBLE WALLS INSULATED FOR THERMAL PROTECTION AND SUPPORT OF THE ROTATING CYLINDER MOVING THE PRODUCT. SUCH CYLINDER, COMPLETELY MADE IN COMPOUND STEEL TO OVERCOME THE THERMAL CHANGES, IS DEVELOPED WITH A PERFORATED PLATE FOR THE CONTAINMENT AND SPECIAL BLENDERS ON THE RIGHT AND LEFT SIDE PLACED ON DIFFERENT LEVELS TO GET A PERFECT BLENDING OF COFFEE. AT THE END OF THE ROASTING CYCLE, THE PRODUCT UNLOADING IS ALLOWED BY A WIDE DOOR WITH MANUAL OPENING/CLOSING SYSTEM.
HEATING GAS GENERATOR OF NEW CONCEPT, PATENTED, COMPLETE OF BURNER, RAMP VALVES FOR GAS SAFETY AND ELECTRONIC EQUIPMENTS FOR FLAME CONTROL RATIFIED AND COMPLETE OF SIGNALLING ALARM.
COOLING TANK IN STAINLESS STEEL: WIDE SURFACE PERFORATED WITH TWO ARMS AND CROSSED FLOWS. UNLOADING MOUTH WITH HAND DRIVE.
SUPPORTING FRAME: MONO-BLOCK, PLATE PRESS-BENDED, STEEL MADE, SUPPORTING THE COMPONENTS PREVIOUSLY DESCRIBED.
SAFETY PROTECTION FOR COOLING TANK
ELECTRIC CONTROL BOARD FOR MACHINE MANAGEMENT ACCORDING CE RULES INTEGRATED. COMPLETE OF PLC + TOUCH SCREEN FOR ROASTING MACHINE CONTROL AND MANAGEMENT.
POSSIBLE RECORDING OF ROASTING PARAMETERS
CYCLONE FOR CHAFFS COLLECTING.
INDEPENDENT MOTORIZATION FOR ROASTING DRUM AND COOLING TANK
INDEPENDENT ELECTRIC-FAN FOR ROASTING DRUM AND ELECTRIC –FAN FOR COOLING TANK.

QUANTITY: 1

Learn More