Search results for: 'the O A full'

REFERENCE NUMBER: M-5128 (121285KMN11UF) L FULL AUTOMATIC TRANSFER LINE FOR INNER SPRING UNITS FULL AUTOMATIC TRANSFER LINE FOR INNER SPRING UNITS MODEL: FC-90 PRODUCTION: 12 SPRING UNITS PER HOUR (SPRING UNIT SIZE 1.5 M X 2 M) SPRING TYPE: BONNELL SPRING DIAMETER: 67 TO 90mm STEEL WIRE DIAMETER: 1.9 TO 2.5mm SPRING HEIGHT (CAN BE CUSTOMIZED): 100 TO 180mm (<80mm NEEDS TO BE CUSTOMIZED) SPRING COILS: 4 TO 7 COILS HELICAL WIRE DIAMETER: 1.3 TO 1.4mm MAXIMUM SPRING UNIT WIDTH: 2050mm QUANTITY AVAILABLE: 1 Learn More

TT-4184 MITSUBIHI 3H, 6 COLORS, SIZE 103 X 73, YEAR 1999 1ST COATER, DRYER, 2ND COATER, DRYER 6 COLORS + 2 COATERS + INTERMEDIATE DRYER + END OF PRESS DRYERS-EXTENDED DELIVERY. QUANTITY: 1 Learn More

V-1961 AUTOMATIC PET PAD MAKING MACHINE – 400 PADS PER MINUTE – 350KW-480,000 PADS IN 20 HOURS (PER 3-SHIFT DAY, AFTER REMOVING EFFICIENCIES = 500,000 PADS PER 24 HOURS) FULLY AUTOMATIC PET PAD MAKING MACHINE THE MACHINE OPERATORS JOB IS ONLY TO ADD THE RAW MATERIALS AND VERIFY THAT THE MACHINE IS RUNNING PROPERLY. ABSORBENT CORE CRUSH, MIX AND MAKE THE CORE. TOP SHEET, ABSORBENT CORE, BACK SHEET (PE FILM), LAMINATED. FINAL PRODUCTS ARE FOLDED HORIZONTALLY CUTS PAD INTO FINAL SIZE CREATES VERTICAL FOLD MAIN TECHNICAL PARAMETERS: DESIGN SPEED: 300 METERS PER MINUTE (60mm x 90mm) WORKING SPEED: 250 METERS PER MINUTE (60mm x 90mm) QUALIFIED RATE: >98% EFFICIENCY: >85% INSTALLED POWER: 300 KW (MAIN MACHINE) ELECTRICITY: 480 VOLTS, 60 Hz AIR PRESSURE: 0.6 MPA, 2.6 m3 PER MINUTE TOTAL WEIGHT: 65 TONS PRODUCT SIZE: 400mm x 600mm, 600mm x 600mm, 900mm x 600mm, 560mm x 560mm, 4 SIZES, ACCORDING TO ORDER QUANTITY: 1 Learn More

REFERENCE NUMBER: T-6924 100L/H LIQUID SOAP PRODUCTION LINE ITEM 001 ARO- 250L RO WATER TREATMENT 1. CAPACITY: 250L/H; DESIGN VOLUME: 250L/H 2. WATER CONDUCTIVITY: PURE WATER MACHINE: ≤8US/CM (RAW WATER CONDUCTIVITY ≤300US) 3. RECLAIM RATE (%) 4. PH VALUE: BETWEEN 5.5 AND 7.5 5. DESALINATION RATE: WHOLE MACHINE DESALINATION RATE ≥98%, SINGLE MEMBRANE LOWEST DESALINATION RATE 99.6% 6. PRODUCT ADVANTAGES: HANGZHOU SOUTH PRESSURE PUMP, ANHYDROUS AUTOMATIC STOP, LOW PRESSURE, AUTOMATIC PURE WATER PIPE WATER AUTOMATIC FILLING WATER AND STOPFULL AUTOMATIC FUNCTIONS COMPLETE EQUIPMENT ADOPTS STAINLESS STEEL MATERIAL (PVC DRAINAGE PIPE, BEAUTIFUL APPEARANCE AND PRESSURE RESISTANCE. HIGH PRESSURE PUMP IS SOUTH PUMP, IMPORTED SOLENOID VALVE AND DOW MEMBRANE. 7. TECHNOLOGY: ATOM-PE TANKS-RAW WATER PUMP-QUARTZ-SAND FILTERS-ACTIVATED CARBON FILTER-SECURITY FILTER-REVERSE OSMOSIS HOST-PURE WATER TANK-PURE WATER PUMPS-UV STERILIZER-LIQUID WASHING WATER INTRODUCED BY HOST-STORAGE TANK-EDI SYSTEMS-HIGH PURITY WATER TANK-WATER CONSUMING POINT 8. SOURCE WATER PUMP: MODEL: CHL4-20 FLUX: 3M3/H DIAMETER: 35M POWER: 0.35KW MATERIAL: SUS304 1 SET 9. FRP/SUS304 SAND FILTER TYPE: VERTICAL CYLINDER RINSE DEVICE: MANUAL/AUTO FLUSH EQUIPMENT WATER OUTLET: 1 M3/H SIZE: φ250 X 1250 (mm) BARREL HEIGHT: 2/3 OF PILLAR HEIGHT WORK PRESSURE: ≤0.8MPA EQUIPMENT MATERIAL: FRP/SUS304 FILTER MEDIUM: REFINED QUARTZ SAND~5 1 SET 10. FRP/SUS304 CARBON FILTER TYPE: VERTICAL CYLINDER RINSE DEVICE: MANUAL/AUTO FLUSH EQUIPMENT WATER OUTPUT: 1M3/H SIZE: φ250*1250 (mm) BARREL HEIGHT: 2/3 OF PILLAR HEIGHT WORK PRESSURE: ≤0.9MPA EQUIPMENT MATERIAL: FRP/SUS304 FILTER MEDIUM: ACTIVATED CARBON, PARTICLE SIZE: 0.3 TO 0.4M, 25KG 1 SET 11. PRECISION FILTER SIZE: 20 INCH, 5UM FILTER ELEMENT 2 PCS FLUX: 2T/H MATERIAL: OUTSIDE FILM BLUE PLASTIC EQUIP: 20 INCH 5UM SPRAY FILTER 2 PIECE 1 SET 12. STAINLESS STEEL HIGH PRESSURE PUMP MODEL: CDL WATER OUTPUT: 2T/H DIAMETER: 120M POWER: 0.75KW 1 SET 13. MEMBRANE SHELL MODEL: 4040, MATERIAL: STAINLESS STEEL, 1 LINE 14. REVERSE OSMOSIS MEMBRANE MODEL: DOWREBE4040 DOMESTIC MEMBRANE SINGLE FLOW: 0.25T/H 1 PC 15. CONDUCTIVITY METER - ONLINE MEASURE, CM-240 DIGITAL DISPLAY, 2 SETS 16. WATER SOLENOID VALVE DN25 STAINLESS STEEL, 1 SET 17. RINSE SOLENOID VALVE DN20 STAINLESS STEEL, 1 SET 18. CONTROL VALVE SUS DN20, 2 SETS 19. FLOW METER MODEL: 20750, 0 TO 11GPM, 2 SETS 20. PRESSURE METER, MODEL: 0 TO 0.6MPA, MODEL: 0 TO 2.5MPA, 4 PCS 21. LOW PRESSURE CONTROLLER MODEL: PSI, 1 SET 22. EQUIPMENT RACK, MATERIAL: SUS304, 1 SET 23. PIPELINE, PIPE FITTINGS, FRP/SUS304, 1 SET 24. ELECTRICAL CONTROL CABINET, SUS304 MATERIAL, 1 SET 25. ELECTRICAL COMPONENTS, DELIXI, 1 SET 26. UV DEVICE, 24W OVERCURRENT UV STERILIZER, 1 SET QUANTITY: 1 SET ITEM 002 AHM-200L LIQUID HOMOGENIZER MIXER 1. MAIN POT FULL VOLUME: 240L WORKING CAPACITY: 60 TO 200L INTERNAL AND EXTERNAL SANITATION POLISHING≥300 MESH A. INNER TANK SUS316L, THICK: 5mm SEAL HEAD: SUS316L, THICKNESS: 4mm IMPORT STAINLESS STEEL B. JACKET SUS304, THICK: 5mm, ELECTRIC HEATING: 12KW TAP WATER COOLING BOTTOM INLET AND TOP OUTLET C. SHELL SUS304, THICK: 3mm INSULATION MEDIA: ALUMINUM SILICATE D. LID SUS304, HALF OPEN HINGED LID GMP HYGIENE STANDARDS E. AGITATOR FRAME TYPE WALL SCRAPER MIXING, WITH ONE FIXED PROPELLER FLANGE SHAFT COUPLING STIRRER PADDLE: SUS316L, THICK: 10mm SCRAPER BLADE: PTFE MATERIAL, REMOVE PRODUCT FROM THE WALL F. AGITATOR MOTOR POWER: 2.2KW SIEMENS MOTOR AND REDUCER SPEED: 0 TO 65RPM DELTA FREQUENCY INVERTER G. SEALING OF AGITATOR THREE WAY SKELETON OIL SEAL + NSK BEARING H. BOTTOM HOMOGENIZER POWER: 4KW, SIEMENS MOTOR SUS316L, ROTOR AND STATOR HIGH SHEARING HOMOGENIZER SPEED: 0 TO 3600 RPM, DELTA INVERTER I. SEALING OF HOMOGENIZER MECHANICAL SEAL+ WATER COOLING CIRCULATION J. DISCHARGING WAY SUS316L, DN36 BOTTOM BALL VALVE HYGIENE LEVEL 2. ELECTRIC CONTROL SYSTEM SHELL MATERIAL: SUS304, THICKNESS: 2mm STAINLESS STEEL SAND PANEL STANDARD CONFIGURATION: INSTRUMENT, BUTTON, APPLIANCE COMPONENTS SCHNEIDER 3. PLATFORM & BRACKET ALL SS AND EQUIPPED WITH ANTI-SKID ALUMINUM PLATE BEST CONFIGURATION 4. OTHER ACCESSORY SPARE PARTS PROVIDE NAMES & QUANTITY OF SPECIAL AND VULNERABLE PARTS RANDOM QUANTITY: 1 SET ITEM 003 HORIZONTAL LIQUID FILLING MACHINE CYLINDER - BRAND: AIRTAC FAMOUS BRAND, LOW GAS CONSUMPTION STRONG DRIVING FORCE CONTROL SYSTEM - "MANUAL/AUTOMATIC" CONTROL, "RESET", "MANOMETER". FOOT CONTROL PANEL - CONTROLLED BY FOOT, MATERIALS ARE FILLED INTO BOTTLES WHEN PRESS THIS PANEL. MATERIAL ENTRANCE - USING STEEL PIPE CONNECT WITH CHARGING BASKET. FILLING NOZZLE - FILLING VOLUME AND FILLING NOZZLE SIZE IS OPTIONAL. 1 STRUCTURE SELF-SUCTION PRODUCTS TO FILLING MACHINE FULL PNEUMATIC CONTROL NORMAL GRAVITY TYPE FEEDING PRODUCTS. CHANGE MANUAL" AND "AUTOMATIC" FILLING STATE PISTON CYLINDER CONTROL VOLUME 2 PRINCIPLE COMPRESSED AIR CONTROL DRIVE USING LEAD SCREW, COUNTER, MAKE FILLING QUANTITY ADJUSTMENT ACCURATE EMERGENCY SWITCH, PISTON AUTOMATICALLY RETREAT BACK TO INITIAL BITS, FILLING STOP. 3 CYLINDER: AIRTAC 4 MATERIAL: SS316L FOR ALL CONTACT PRODUCTS PART, OTHER PARTS SS304 8 FILLING RANGE: 500 TO 5000ML 10 FILLING SPEED: 0 TO 30BPM (ADJUSTABLE) 12 AIR PRESSURE: 0.5 TO 0.8MPA 13 WORKING PRESSURE: 0.2 TO 0.5MPA 14 AIR CONSUMPTION: 0.05M3/MIN 15 WEIGHT: 45KG QUANTITY: 1 SET ITEM 004 SEMI AUTOMATIC CAPPING MACHINE CAPPING TIME & TORQUE CONTROL HEIGHT CONTROL ACCORDING TO BOTTLES CAPPING CONTROL MOTOR - MOVE AROUND ON BOTH SIDES TO CONTROL CAPPING CAPS SCREW CAPPING PARTS - 4 SILICONE ROTATING CAPS PART PUMP CAP SETTING PART- FIXING PUMP PART AND THEN ROTATING CAPS 1. BOTTLE LOCK RANGE BOTTLE HEIGHT: 30 TO 300mm BOTTLE WIDTH: 15 TO 100mm 2. LOCK LID WRESTING: STANDARD VALUE 4 TO 8KG/CM 3. POWER: 80W 4. USE OF GAS SOURCE: 0.4 TO 0.6MPA 5. VOLTAGE: 220V/50Hz 6. SIZE: 500 X 380X 700mm 7. NET WEIGHT: 35 KG QUANTITY: 1 SET ITEM 005 ALM -SEMI AUTOMATIC ROUND BOTTLE LABELING MACHINE 1. SCOPE OF APPLICABLE LABELS: WIDTH OF 10 TO 350mm, LENGTH OF 10-150mm 2. DIAMETER OF APPLICATE BOTTLE NECK: EXTERNAL DIAMETER OF 20-80(mm), HEIGHT OF 30 TO 200(mm) 3. MAX ROLL INSIDE DIAMETER: 76mm 4. PRODUCTION CAPACITY: 1200 TO 2400 BOTTLES/HOUR (IT DEPENDS ON SIZE OF LABEL AND SPEED OF MANUAL OPERATION) 5. RATED VOLTAGE: 220V/50Hz 6. TOTAL POWER: 100W QUANTITY: 1 SET ITEM 006 ALM -SEMI AUTOMATIC FLAT BOTTLE LABELING MACHINE 1. SCOPE OF APPLICABLE LABELS: WIDTH OF 10 TO 350mm, LENGTH OF 10 TO 150mm 2. DIAMETER OF APPLICATE BOTTLE NECK: EXTERNAL DIAMETER OF 20 TO 80(mm), HEIGHT OF 30 TO 200(mm) 3. MAX ROLL INSIDE DIAMETER: 76mm 4. PRODUCTION CAPACITY: 1200 TO 2400 BOTTLES/HOUR (IT DEPENDS ON SIZE OF LABEL AND SPEED OF MANUAL OPERATION) 5. RATED VOLTAGE: 220V/50Hz 6. TOTAL POWER: 100W QUANTITY: 1 SET ITEM 007 HANDHELD INKJET PRINTER 1. MATERIAL: STAINLESS STEEL 2. DIMENSION: 130 X 128 X 200mm 3. CONTROL SCREEN: COLOR TOUCH SCREEN, INTELLIGENT TOUCH SCREEN (CAN BE CONTROLLED BY UNIVERSAL WIRELESS MOUSE, CAN ALSO BE IMPORTED ON THE COMPUTER AND IMPORTED THROUGH U DISK) 4. PRINTING: 360° ALL-IN-ONE CODING, WHETHER IT IS ARBITRARILY FACING FORWARD AND DOWNWARD, TO MEET PRODUCTION NEEDS. 5. PRINTING FONT: BUILT-IN NATIONAL STANDARD FULL FONT, PINYIN INPUT METHOD, TOUCH ONLINE EDITING, NO NEED TO CONNECT TO THE COMPUTER, EASY TO OPERATE. 6. PRINTED FONTS: HIGH-DEFINITION PRINTED FONTS (IE PRINTED) DOT MATRIX FONTS, BUILT-IN MULTIPLE CHINESE AND ENGLISH FONTS. 7. PRINTING GRAPHICS: CAN SPRAY A VARIETY OF TRADEMARK PATTERNS, GRAPHICS CAN BE IMPORTED THROUGH THE U DISK. 8. PRINTING ACCURACY: 600DPI (HIGH DEFINITION) 9. NUMBER OF PRINT LINES: ADJUSTABLE FROM ONE TO SEVEN LINES 10. PRINTING HEIGHT: CAN BE PRINTED 2mm-13mm (ADJUSTABLE) PLUS NOZZLE (CAN BE INCREASED TO 50 mm) 11. PRINTING BAR CODE: BAR CODE, 2D BAR CODE 12. WEIGHT: 1.18KG 13. PRINTING MATERIALS: WOOD BOARD, CARTON, STONE, MDF, LIGHT STEEL KEEL, PIPE, METAL, PLASTIC, ALUMINUM FOIL, CABLE, ETC. QUANTITY: 1 SET ITEM 008 AIR COMPRESSOR 1. POWER: 4KW QUANTITY: 1 SET Learn More

TT-7587 SIEMENS TG50D5/W701DS GAS TURBINE GENERATOR, 127.8 MW, YEAR 1995 1. SIEMENS WESTINGHOUSE TG50D5/W701DS 127.8 MW GAS TURBINE GENERATOR PACKAGES FOR SALE. THE TURBINE PACKAGES TOGETHER OFFER 255 MW READY TO SHIP EQUIPMENT. THIS TECHNOLOGY IS ONE OF THE MOST WIDESPREAD MIDDLE SIZE ENGINES (100-104 MW) FOR POWER GENERATION AND THE ONLY TURBINE OF ITS SIZE THAT CAN OPERATE ON HEAVY FUEL OIL (HFO). 2. THE UNITS ARE OFFERED WITH SOME OF THE REQUIRED BALANCE OF PLANT BY SEPARATE NEGOTIATION. 3. THESE UNITS WERE INSTALLED AND OPERATED IN A POWER STATION FROM 1996 UNTIL THE END OF 2004, WHEN THEY WERE DISMANTLED AS THE RESULT OF A PLANT UPGRADE. THE UNITS WERE PURCHASED AND UPGRADED BY THE BUYER TO 127.8 MW NOMINAL CAPACITY EACH. THEY ALSO FULLY REFURBISHED THE UNITS TO ZERO HOURS. THE TURBINES HAVE THE CAPABILITY OF BEING ABLE TO SWITCH BETWEEN NATURAL GAS AND LIQUID FUEL WHILE STILL OPERATING UNDER LOAD. QUANTITY: 2 Learn More

REFERENCE NUMBER: M-4566 (1111225RSJ10U) L THERMOPLASTIC HOTMELT COATING LINE MP ENGINEERING TYPE HM59-SD3 YEAR 2005 WIDTH 102” (2590mm) YEAR: 2005 TYPE: HM59-SD3 MATR: 404/04 ROLL FACE: 2600mm (102”) WORKING WIDTH: 2400mm (95”) VOLTAGE: 480/3/60 CONTROL VOLTAGE: 110/60 CONSISTING OF: CAROUSEL 3 POSITION LET-OFF, ENTRY ON ACCUMULATOR WITH HOT-WIRE SEAMING DEVICE, 8000 VOLT STATIC ELIMINATOR, PNEUMATICALLY OPERATED FABRIC HOLDING DEVICE FOR TENSION CONTROL, ACCUMULATOR WITH 8-ROLLS UP AND 9-ROLLS DOWN APPROX.. 80-YARD CAPACITY, COMPENSATING ARM ON EXIT SIDE. ROLLS ARE 4” DIA. X 102” FACE ALUMINUM, CONTROL PANEL MOUNTED ONTO FRAMEWORK, FULLY ENCLOSED CAGE. SECOND ACCUMULATOR WITH ROLL CRADLE FOR SECOND SUBSTRATE LET-OFF, ACCUMULATOR WITH 9-ROLLS UP AND 10 ROLLS DOWN, APPROX.. 54 YARD CAPACITY, ROLLS ARE 4’ DIA. X 102” FACE ALUMINUM, INCLUDES 8000 VOLT STATIC ELIMINATOR AND PNEUMATIC FABRIC HOLDING FOR TENSION, PENDULUM TYPE GUIDING DEVICE ON EXIT SIDE, CONTROL PANEL MOUNTED ONTO FRAMEWORK, FULLY ENCLOSED CAGE. OVERHEAD GANTRY WITH ACCESS STAIRS ON RIGHT SIDE OF FIRST ACCUMULATOR, EXTENDS OVER THE EXTRUDER WITH JIB MOUNTED FOR EASE IN REMOVING DIE FROM MACHINE, GUIDING/CENTERING DEVICE MOUNTED ONTO GANTRY FEEDING COATING HEAD. MP ENGINEERING EXTRUDER/APPLICATOR TYPE HM59-SD3, MATR. NO. 402/04, WITH 102” DIE, 98” RUBBER-BELT WITH PNEUMATIC CYLINDERS FOR BELT TENSION AND GUIDING, HEATED CYLINDER BACKING TO DIE, OPERATOR PLATFORM, CONTROLS MOUTNED IN DOOR AND OPERATOR TOUCH SCREEN PANEL. (NOTE: THESE ARE PRESENTLY MOUNTED ON PRODUCTION LINE AND WILL BE REMOVED AND PLACED BACK INTO/ONTO APPLICATOR. 480/3/60 COATEM SISTEMI C.R.L. IMBALLAGIO & HOT MELT EXTRUDER, S/N 50701, TYPE/MODEL CE-200, WITH DIGITAL MICROPROCESSOR AND INVERTER FOR SPEED VARIATION, DESIGNED TO WORK MAINLY WITH POLYESTER, POLYAMIDE AND POLYURETHANE BUT CAN ALSO EXTRUDE ABS, POLYTHENE, POLYPROPYLENE AND ADHESIVES LIKE EVA ADHESIVES. 480/3/60 CONAIR DRYER CD-300, PL-D-196-1, MODEL D03H4101310, S/N 9D0597, 480/3/60, AND HOPPER. THIRD ACCUMULATOR FOR BONDED PRODUCT WITH 6-ROLLS UP AND 7-ROLLS DOWN, APPROX…60-YARD CAPACITY, ROLLS ARE 6” DIA. X 102” FACE ALUMINUM, WITH DRAW-ROLL TENSION DEVICE MOUNTED ONTO EXIT, OVERHEAD CARRIER ROLLS AND FRAMEWORK DELIVERY TO ELECTRIC A-FRAME WINDER WITH 102” FACE LAY-ON ROLL, AND SEMI-AUTOMATIC BATCHER FOR INDIVIDUAL ROLLS, 2-ROLL SURFACE WINDING 102” FACE WIDTH, OVERHEAD CORE FEED, FABRIC CENTERING DEVICE, ELECTRIC SCISSOR CUT-OFF, KICK-OUT TO 2-ROLL BED, OPERATOR PLATFORM AND OPERATOR CONTROLS. ALL MACHINES PRODUCED BY MP CONFORMS TO EEC DIRECTORY 89/392 CEE (CE MARK) TECHNICAL FEATURES OF THE LINE, ACCORDING TO DWG 100-904/1C ROLLERS WIDTH 2600mm WORKING WIDTH 2400mm MAXIMUM DIAMTER OF THE ROLLS OF PU FOAM 1500mm MAXIMUM DIAMETER OF THE UNWOUND ROLLS OF FABRIC 600 ° 1500 MAXIMUM DIAMETER OF THE REWOUND ROLLS 500 ° 1500 (IN CASE YOU ARE REWINDING ROLLS OF FABRIC LAMINATED TO PU FOAM, THE MAXIMUM DIAMETER IS 1750mm) ADJUSTABLE MECHANIC SPEED: 5 TO 50 M/MIN MAIN POWER SUPPLY + NEUTRAL + EARTH 480+N+E/60 V/HZ VOLTAGE ON CONTROL PANELS 110/60 V/HZ INSTALLED POWER FOR MOTORS 22KW INSTALLED POWER FOR IR HEATER 14,25KW INSTALLED POWER TO HEAT THE SLOT-DIE 32KW INSTALLED POWER FOR THE THERMAL OIL HEATING UNIT FOR THE CALENDERING ROLLERS 32,2KW INSTALLED POWER FOR THE CHILLER 12,9KW A.C. MOTORS, DRIVER, ELECTRIC CABLES ARE ACCORDING TO CEI NORMS BACKGEAR ROLLERS, WITH PAINTED SURFACE OR ALUMINUM MADE WITH DIAMETER 100/120/150mm COMPRESSED AIR CONSUMPTION, AT 6 BAR 1500LT/H COOLING WATER CONSUMPTION (WATER MUST HAVE A TEMPERATURE NOT HIGHER THAN 10°C) 5500LT/H ADJUSTABLE TENSION ON THE REWOUND MATERIALS 5 A 35 KG. PAINTING GREEN RAL 6027 E BLUE MARINE RAL 5021 A.C. MOTORS CONTROL THE SPEED OF THE MACHINES, AND ARE AUTOMATICALLY SYNCHRONISED THROUGH ELECTRONIC DRIVES (INVERTER) AND PNEUMATIC DANCER UNITS (COMPENSTAORS) ESTRUDER: CAPACITY UP TO 200 KG/H (DEPENDING ON THE VISCOSITY OF THE ADHESIVE TO BE EXTRUDED) POWER OF THE MOTOR AND RESISTANCES: 90KW MAXIMUM MELTING TEMPERATURE: 220°C MATERIALS TO BE PROCESSED NONWOVENS 30:150 GR/M2 SYNTHETIC AND NATURAL FABRICS (EXCLUDING STRETCHY FABRICS) WITH WEIGHT 100:600 GR/M2 SCRIMS FOR BACKING FABRIC WITH WEIGHT 70:120 G/M2 MAXIMUM THICKNESS OF PU FOAM 15mm MINIMUM THICKNESS OF PU FOAM 2mm DENSITY OF PU FOAM 22/40 KG/M3 THERMOPLASTIC ADHESIVE TO BE COATED THERMOPLASTIC HOTMELTS (COPOLYAMMIDE, COPOLYESTER, EVA AND POLYURETHANE THERMOPLASTIC HOTMELT GRANULES) DATA REFERRING TO PRODUCTION THE PRODUCTION SPEED CAN CHANGE, DEPENDING ON THE KIND OF HOTMELTS, ON THEIR MELTING TEMPERATURE, ON THEIR VISCOSITY, AND ON THE GRAMS PER SQUARED METER TO BE COATED QUANTITY AVAILABLE: 1 Learn More

J-2628 COMPLETE BIAS BINDING SYSTEM (SEWING, SLITTING & WINDING SYSTEM) – NEW SEWING MACHINE FOLDS FABRIC, STITCHES EDGE OF FABRIC FOR TWILL EFFECT WORKS TOGETHER WITH WINDING MACHINE AND STRIP CUTTING MACHINE WINDING MACHINE OPENS PREVIOUSLY FORMED TUBE MATERIAL, SPIRALLY, IN THE BIAS, AND REWINDS A SINGLE PLY ROLL, AT BOTTOM OF MACHINE THERE IS A KNIFE TO CUT SEWING FABRIC SEPARATELY, PREPARED FOR THE SLITTER SLITTER MACHINE HAS MANUAL, SEMI-AUTOMATIC AND FULLY AUTOMATIC MODES. WILL SLIT ANY TYPE OF MATERIAL ON THE ROLL (OPEN KNITS, WOVEN FABRIC, LEATHER, POLYESTER, SOME PAPER PRODUCTS, NONWOVEN, ETC) QUANTITY: 1 SLITTER, 1 WINDER Learn More

TT-7534 BALTIMORE COMPLETE BOTTLING LINE SIDEL FOR STILL WATER, 14400 BPH, YEAR 2006 1. BRAND: BALTIMORE 2. YEAR: 2006 3. SPEED: 14400 BPH 4. PRODUCTS: WATER (STILL) 5. CONTAINERS: PET 6. FORMATS: 0.50 L, 0.75 L, 1.5 L 7. SAFETY FEATURES: YES 8. MACHINE HOURS: 11000 HOURS 9. FILL TYPE: VOLUMETRIC 10. NECK TYPE: 25 TO 30mm Learn More

REFERENCE NUMBER: X-0008 ELECTRONICALLY CONTROLLED SEMI-AUTOMATIC FILLING FOR PILLOW, CUSHIONS, QUILTS, BABY MATTRESSES AND MORE THIS MACHINE IS A STAND-ALONE AND VERY VERSATILE PILLOW STUFFING AND BAGGING MACHINE. ITS SIMPLE OPERATION ALLOWS TO USE THE SAME EQUIPMENT TO ACCOMPLISH THE TWO PROCESSES: STUFFING A BATT OR A FOAM CORE IN A COVER (OR AN INSERT IN THE FINAL DEC COVER / A PILLOW IN THE FINAL ZIPPERED COVER) AND/OR PUT A FINISHED PILLOW IN A BAG (INDIVIDUAL PE BAG, TWIN-PACK BAG, ZIPPERED VINYL BAG, ETC). THE MACHINE CAN BE LOADED MANUALLY OR WITH A CONVEYOR ON THE REAR PART, WHILE AN OPERATOR IS NEEDED IN THE FRONT: HE PUTS THE COVER/BAG ONTO THE STUFFING BELTS, ACTIVATES THE TENSIONING FORKS WITH THE PEDAL AND HOLDING THE COVER/BAG FACILITATES THE PILLOW STUFFING. POWER SUPPLY IS 400 VOLTS, WILL NEED A TRANSFORMER TO OPERATE ON 480 VOLTS, INQUIRE IF NEEDED Learn More

REFERENCE NUMBER: V-0025 COTTON PAD, BALL, SWAB MACHINES M-5138 SQUARE COTTON PAD PRODUCTION MACHINE M-5139 COTTON GAUZE PAD PRODUCTION MACHINE M-5140 MACHINE TO PRODUCE VARIOUS TYPES OF COTTON PADS M-5141 COTTON PAD PRODUCTION MACHINE M-5142 MAKEUP REMOVING COTTON PAD PRODUCTION MACHINE M-5143 ROUND COTTON PAD MAKING MACHINE M-5144 SQUARE ABSORBENT COTTON PAD PRODUCTION MACHINE M-5145 ROUND ABSORBENT COTTON PAD PRODUCTION MACHINE M-5146 ROUND COTTON PADS MAKING MACHINE M-5147 COTTON PAD MAKING MACHINE M-5148 COTTON PAD MAKING MACHINE M-5168 COTTON PADS MAKING MACHINE M-5169 COTTON Q-TIP MAKING MACHINE (100PCS/BAG) M-5170 COTTON BALL MAKING MACHINE (NEW) M-5171 COSMETIC COTTON PAD (GLOVE SHAPE) MAKING MACHINE M-5172 COSMETIC COTTON PAD MAKING MACHINE (ROUND PAD) M-5101 MEDICAL COTTON BALL MAKING MACHINE 20KG/HOUR QUANTITY AVAILABLE: 17 Learn More