Search results for: 'vertical b'

REFERENCE NUMBER: K-9424 MURATA 377 FTO & MURATA 607 WINDER MURATA 377 FTO YEAR: 1995-1997 QUANTITY: 2 MURATA 607 ASSEMBLING WINDER YEAR: 1995 QUANTITY: 2 QUANTITY AVAILABLE: 4 Learn More

MACHINE EQUIPPED WITH : - INLET BY PLATFORM + WEFTSTRAIGHTNER + DOGAL CYLINDER - WORKING WIDTH 2400mm - PINS WITH ANTIDEPINNING CLIPS VERTICAL CHAINS - FULL ACCESSORIED TO WORK OPEN KNITTING FABRICS - 6 METERS LONG OVEN HEATED BY GAS BURNERS - OVERFEEDING AT INLET - STEAMING TUNNEL ON INLET FIELD - COOLING AREA AT EXIT FIELD - FOLDER AND SMALL ROLL AT EXIT Learn More

REFERENCE NUMBER: M-4249 (10105MNAD9UC) K SANTEX OPEN WIDTH COMPACTOR YEAR 1996 WIDTH 2200mm SANTEX OPEN WIDTH COMPACTOR WIDTH 2200mm TYPE SANTACOMPACT YEAR 1996 CONSISTS OF: TENSION BAR, LATTICE ROLL GUIDER W/FULL WIDTH SENSOR OPERATOR PLATFORM, OPEN VERTICAL PIN TENTER FOR KNITS, TANDEMATIC SPLIT LEVEL UNCURLERS, OVERFEED, PINNING BRUSHES, STEAMING SECTION, RAIL GUIDES, GUMMING, SELVEDEGE TRIMMING, OPEN WIDTH COMPACTOR FELT TYPE SCRAY, 2 ROLL BATCHER WITH EDGE GUIDING AND INSPECTION BOARD. QUANTITY: 1 Learn More

STENTER BRUCKNER YEAR 1986 WORKING WIDTH 2400mm Learn More

REFERENCE NUMBER: K-9991 MEZZERA OPEN-WIDTH WASHING MACHINES YEAR 2002 – 3800mm BRAND/O.E.M.(ORIGINAL EQUIPMENT MANUFACTURER): MEZZERA MACHINERY: OPEN-WIDTH WASHING MACHINES WIDTH: 3800 MM YEAR: 2002 CONTINUOUS OPEN WIDTH WASHING LINE WIDTH : 3800 MM WORKING WIDTH: 3600 MM - DOUBLE-ENTRY, CENTERING E + L KF20 - UNIT-WIDTH WASHING CYLINDER, MODEL ACTIVA 30, DOUBLE THREADING OF THE FABRIC - ALL MOTORS WITH INVERTERS, CONTROL CABINET, AND SYNOPTIC PANEL - VERTICAL-DRYING RAMALLUMIN COMPOSED BY 2 COLUMNS TO 8 CYLINDERS FOR DRYING ON BOTH SIDES OF THE FABRIC, FOR A TOTAL OF 16 CYLINDERS DRYING Learn More

REFERENCE NUMBER: M-4868 (1111275NKG10RX) L PUB BREWERY 20HL SPECIFICATION: 1. MALT HANDLING - CYLINDER-CONIC MALT SILO WITH 25M³ CONTENT, MADE IN FIBRE GLASS / PLASTIC, STANDING OUTDOOR ON STEEL CONSTRUCTION - MALT CONVEYORS / SPIRAL CONVEYOR INTO 1ST FLOOR - 2-ROLLER MALT MILL - GRIST CASE - FALL PIPE IN MASH COPPER (FOR DUST FREE MASHING-IN) - GIBBET-LIFT FOR BAGGED SPECIAL MALTS 2. BREWHOUSE TOWER BREWHOUSE FOR 20 HL / BREW, COMPLETE IN STAINLESS STEEL, BUILT 1994, STEAM HEATED, ISOLATED AND COVERED WITH STAINLESS STEEL SHEET, 2 CRANE EYELET, 2 STAINLESS STEEL PLATFORM, WITH: - MASH- / WORT COPPER WITH BOTTOM HEATING ZONE AND INTERIOR COOKER, SIDEWAYS AGITATOR, MANWAY ENTRANCE HATCH, LIGHTNING, STEAM REGULATION VALVE - LAUTER TUN, WITH STAINLESS STEEL RAKING MACHINE WITH SEW-DRIVE FROM TOP, WITH SPENT GRAINS SLIDER, STAINLESS STEEL FALSE BOTTOM, SPENT GRAINS HATCH, VERTICAL SIGHT GLASS, LIGHTNING, SPRAY HEAD, DOME LID WITH BUILT IN CONTROL CABINET - SPINDLE STATION WITH WASHING TABLE IN STAINLESS STEEL, ABOUT 1,5M WALL ASSEMBLED - HOT WATER TANK, WITH 30 HL, IN STAINLESS STEEL, ISOLATED AND COVERED WITH STAINLESS STEEL SHEET, HEATABLE, WITH MANWAY IN THE WALL, LEVEL DISPLAY - PRESSURE RAISING PUMP - WORT COOLING, 1-STAGE PLATE APPARATUS - WORT AERATION IN STAINLESS STEEL 3. FERMENTING- AND STORAGE TANKS - 5 CCTS, WITH 40 HL NET / 46 HL GROSS CONTENT, ALL TANKS 3 BAR, BUILT 1994, STANDING ON FEET, PI-ISOLATED FULLY WELDED WITH STAINLESS STEEL JACKET, WITH JACKET COOLING FROM CONE BELOW TO ½ WALL 60 LT COOLING JACKET 3 BAR, WITH MANWAY IN THE WALL, 2 OUTLETS WITH BUTTERFLY VALVES, TEMPERATURE SENSOR PT100, SPRAY HEAD, PULLED DOWN CLEANING PIPE WITH BUTTERFLY VALVE, BUNGING ARMATURE, OVER PRESSURE VALVE, SAMPLER, 2 CRANE EYELETS, 2 OF THE TANKS WITH LEVEL DISPLAY - DIGITAL TEMPERATURE CONTROL FOR 5 TANKS IN STAINLESS STEEL CONTROL CABINET - CIRCULATING PUMP IN STAINLESS STEEL, MOBILE, WITH SWITCH - MANY GOOD BEER HOSES - 6 X 10 HL BEER DISPENSING TANKS, MAKE DUO TANK, BUILT 2002, 3,0 / 4,3 BAR, COOL ABLE, ISOLATED WITH STAINLESS STEEL-JACKET FULLY WELDED, FOR INLINE-OPERATION, LYING IN RACK, SCREWED STAINLESS STEEL RACK, WITH PRESSURE ARMATURE, OUTLET ARMATURE WITH REDUCTION TO BARE CONNECTION, MANWAY WITH BIG SIGHT GLASS IN MANWAY LED - PANEL FOR 3 TYPES OF BEER 4. FILLING COMBINED BOTTLE-/KEGGING PLANT, WITH 1 CLEANING TUB, HEATED AND 1 REBUILT KEG: - BOTTLE CLEANING MACHINE FOR CLEANING OF 8 BOTTLES INSIDE AND OUTSIDE, FOR UP TO 2LT BOTTLES - BOTTLE FILLING STATION WITH HUB CYLINDER FROM BELOW, WITH SPLINTER PROTECTION - COMBINED KEG-CLEANING- AND FILLING STATION - BUILT IN CONTROL CABINET WITH SIEMENS S5 CONTROL AND OPERATING CONSOLE OP 7 5. OTHER EQUIPMENT - STEAM BOILER FOR ABOUT F280 KG/H, WITH GAS BURNER, FULLY SERVICED ON 4TH AUGUST 2014, BUILT IN 1994 - CONDENSATE TUB IN STAINLESS STEEL AT WALL AND SECOND SMALL S/S-TUB - WATER TREATMENT - STEAM REGULATION AND CONDENSATE VALVES IN CYCLE - STAINLESS STEEL CHIMNEY PLANT ABOUT 8-10M - AIR COMPRESSOR WITH WIND KETTLE, BUILT 1994 - COOLING PLANT / COLD WATER PLANT, MAKE L&R KÄLTETECHNIK, TYPE: WRK-17/SL/-5, PLANT BUILT 1997, COOLING AGENT R 407 C, WITH NEW COMPRESSOR AND NEW PLATE HEAT EXCHANGER IN 2014 FOR 10,000 € INVESTED, EVAPORATOR WITH 2 VENTILATOR OUTSIDE HANGING ON THE WALL 6.1 OTHERS - ABOUT 100 KETS, MAKE SCHÄFER, PLUS-KEGS, FLAT FITTING IN DIFFERENT SIZES, NEUTRAL - PARTY-KEGS, WITH BAVARIAN TAP, PU-COVERED IN BLACK AND WITH WOOD-OPTIC - ABOUT 800 NEUTRAL CLIP LOCK BOTTLES EACH 1 LT 6.2 DIMENSIONS THE ROOM HEIGHT IN BREWHOUSE AND CCTS IS 4.50M. THE PLANT AS ASSEMBLED ON 10.75 X 4.38M. PLEASE NOTE THAT THE BREWERY IS ONLY AVAILABLE AS A SINGLE SALE QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4601 BRUCKNER STENTER 2400mm YEAR 2005 8 CHAMBERS PIN CHAIN – HOT OIL HEATED YEAR 2005 ROLLER WIDTH: 2600mm WORKING WIDTH: 2400mm 8 CHAMBER OIL HEAT PIN CHAIN VERTICAL CHAIN WITH PADDER, WEFT STRAIGHTENER, INFEED AND EXIT QUANTITY AVAILABLE: 1 Learn More

MONTEX 14G/K STENTER FRAME YEAR 1991 7 COMPARTMENTS, VERTICAL PIN CHAIN WORKING WIDTH 2200mm THERMOFLUID-HEATING OVERFEEDING, SELVEDGE UNCURLERS AND - GLUEING SYSTEM LONG ENTRY WITH STEAMING COMPARTMENT WITH AT ENTRY : DOUBLE AXIAL UNROLLING SYSTEM AND MONFORTS PADDER 2 BOWLS AT EXIT COOLING COMPARTMENT AND AXIAL BATCHING AS WELL AS PLAITER Learn More

PS-90P POCKET SPRING MACHINE COMPUTERIZED OPERATION SYSTEM REMOVABLE INDEPENDENT HEAT TREATMENT DEVICE CHANGEABLE VERTICAL SPRING TRANSFER STRUCTURE VARIOUS CUSTOMIZED ULTRASONIC WELDING SEAM LOW AND EASY MAINTENANCE, ECONOMICAL INVESTMENT PERFORMANCE: 48 SPRINGS/MIN SPRING TYPE: BARREL/CYLINDRICAL AIR CONSUMPTION: APPROXIMATELY 30M3/H AIR PRESSURE: 0.6 TO 0.7 MPA POWER CONSUMPTION IN TOTAL APPROXIMATELY 10KW VOLTAGE: 3AC, 380V – FREQUENCY: 50/60HZ POWER REQUIREMENTS: INPUT FUSE: 25A – CABLE SECTION: 4 X 10mm2 WORKING TEMPERATURE: +5°C +45°C WEIGHT APPROXIMATELY 1800KG NON-WOVEN FABRIC CONSUMPTION MATERIAL DATA FABRIC DENSITY: 45~90G/M2 FABRIC WIDTH: 450 TO 600mm INNER DIAMETER OF FABRIC ROLL MINIMUM 60mm OUTSIDE DIAMETER OF FABRIC ROLL MAXIMUM 600mm STEEL WIRE CONSUMPTION MATERIAL DATA WIRE GAUGE: 1.6 TO 2.2mm INNER DIAMETER OF WIRE ROLL MINIMUM 320mm OUTSIDE DIAMETER OF WIRE ROLL MAXIMUM 1000mm ACCEPTABLE WEIGHT OF WIRE ROLL MAXIMUM 800KG WORKING RANGE STANDARD OPTION 1 WIRE GAUGE: Ø1.6~ Ø2.2 SPRING WAIST DIAMETER: Ø55~ Ø70 POCKET SPRING HEIGHT: 80~140 STANDARD OPTION 2 WIRE GAUGE: Ø1.6~ Ø2.2 SPRING WAIST DIAMETER: Ø55~ Ø70 POCKET SPRING HEIGHT: 100~160 STANDARD OPTION 3 WIRE GAUGE: Ø1.6~ Ø2.2 SPRING WAIST DIAMETER: Ø55~ Ø70 POCKET SPRING HEIGHT: 120~180 STANDARD OPTION 4 WIRE GAUGE: Ø1.6~ Ø2.2 SPRING WAIST DIAMETER: Ø55~ Ø70 POCKET SPRING HEIGHT: 140~200 STANDARD OPTION 5 WIRE GAUGE: Ø1.6~ Ø2.2 SPRING WAIST DIAMETER: Ø60~ Ø75 POCKET SPRING HEIGHT: 80~140 STANDARD OPTION 6 WIRE GAUGE: Ø1.6~ Ø2.2 SPRING WAIST DIAMETER: Ø60~ Ø75 POCKET SPRING HEIGHT: 100~160 STANDARD OPTION 7 WIRE GAUGE: Ø1.6~ Ø2.2 SPRING WAIST DIAMETER: Ø60~ Ø75 POCKET SPRING HEIGHT: 120~180 STANDARD OPTION 8 WIRE GAUGE: Ø1.6~ Ø2.2 SPRING WAIST DIAMETER: Ø60~ Ø75 POCKET SPRING HEIGHT: 140~200 SPECIAL OPTION 1 WIRE GAUGE: Ø1.6~ Ø2.2 SPRING WAIST DIAMETER: Ø60~ Ø75 POCKET SPRING HEIGHT: 200~240 SPECIAL OPTION 2 WIRE GAUGE: Ø1.6~ Ø2.2 SPRING WAIST DIAMETER: Ø60~ Ø75 POCKET SPRING HEIGHT: 240~260 Learn More

REFERENCE NUMBER: M-4749 (1111ASRPXX10) L RECYCLING PLANT FOR FABRIC CUTTING (1) X MONDEJAR CUTTING MACHINE MODEL CUTTEX 1000, YEAR 1992 (1) X CHUTE FEED FOR ACCUMULATION MATERIAL WITH VENTILATOR (1) X ROLANDO BIELLA ITALY TEARING MACHINE YEAR 1973, NR.6 DRUMS (PLUS 1 SPARE) WORKING WIDTH 1000mm AND ELECTRICAL PANEL COMPLETE WITH 1 ENZIMAGE (1) LLORPIC AUTOMATIC VERTICAL PRESS MODEL ALCOY, YEAR 1994 WITH CHUTE FEED FOR ACCUMULATION MATERIAL VENTILATOR AND ELECTRICAL BOX (4) X BONINO CARDS MODEL CC150/170 YEAR 1992, WITH BRIEST AND FIX FLATS BONINO CHUTE FEED (LIKE FBK533) EXIT CAN 40” X 48” WITH AUTOMATIC CHANGER QUANTITY AVAILABLE: 1 Learn More