Search results for: 'santex c'

REFERENCE NUMBER: M-4255 (101095MAN9R) K SANTEX OVEN YEAR 1992 WIDTH 2500mm - GAS SECOND HAND SANTEX OVEN WIDTH 2500mm YEAR 1992 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-1861 (770235KOL6RX) SANTEX PRE-TREATMENT AND WASHING MACHINE TYPE ACTIWASH YEAR 2002 DESIGNED FOR LOW-TENSION PRE-TREATMENT OF WOVEN AND KNITTED GOODS MANUFACTURER: SANTEX - SWITZERLAND YEAR OF MANUFACTURE: 2002 WORKING WIDTH: 2200/1800 mm SPEED OF MACHINE: 3-100 M/MIN PRODUCTION SPEED: APPROX. 75 M/MIN THE DAILY OUTPUT WILL DEPEND E.G. ON QUALITY AND WEIGHT OF FABRICS/KNIT GOODS YOU WILL WASH ON THESE MACHINES. SO FAR THE PLANT WAS RUNNING AT AN AVERAGE SPEED OF 40 M/MIN, I.E. 2,400 MTRS PER WORKING HOUR. QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: A-1266 (010195GHB12RE) A SANTEX OVEN, WIDTH 2400 MM, YEAR 1992 SANTEX OVEN WORKING WIDTH: 2400 MM YEAR: 1992 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-1795 (77057BHB6R) SANTEX SANTASHRINK YEAR 1997 WIDTH 1800mm SANTEX SANTASHRINK YEAR 1997 WIDTH 1800mm CONSISTING OF: ENTRY UNIT DRY CHAMBERS VIBRATION AND DAMPER UNIT EXIT UNIT ALL MOTORS ELECTRIC PANELS EXHAUSTER MOISTURE MEASURE UNIT ENERGY SAFE UNIT CONTROL COMMANDER SANTAMATIC 2000 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4608 (11116SWJK10R) L VILLARS-SANTEX HOTMELT POWDER SCATTERING AND LAMINATING MACHINE YEAR 1993 WIDTH 2100mm LAMINATING LINE MANUFACTURER: VILLARS (CH) ACTUALLY SANTEX YEAR OF CONSTRUCTION: 1993 WORKING WIDTH: 2200mm (NOMINAL WIDTH 2100mm) OPERATING VOLTAGE: 3X380(400)V TOTAL POWER: 158KW RECOMMENDED MAX. SPEED 10M BUT 15M IS POSSIBLE ORIGINAL CONFIGURATION: INPUT UNIT (WITH POSSIBILITY TO HANG IN ROLLERS BY MEANS OF E.G. FLAT BEARINGS), POWDER SPREADER, INFRARED PREHEATING ZONE AND DOUBLE BAND LAMINATING PRESS (HEATING THROUGH IR) LATER EXTENSION (1997): 2ND INFRARED ZONE WITH COLD WATER COOLED CALENDAR AT THE BACK EQUIPPED WITH SELVEDGE CUTTING SYSTEM WITH ADJUSTABLE INFRARED FOLLOW UP SYSTEM. STRENGTH OF INFRARED CAN BE ADJUSTED SO THAT E.G. THE UPPER SUBSTRATE CAN BE ‘NEGLECTED’. KNOWN PROBLEMS: 1)INFRARED PREHEATING ZONE : 2 IR STRIPS BROKEN 2)CERTAIN PARTS IR ZONES (MOSTLY EXTERIOR ZONES) OF THE DOUBLE BAND LAMINATING PRESS DO NOT LONGER FUNCTION, BUT SECOND PART OF THE MACHINE CAN STILL BE HEATED TILL 160 À 170°C AND EVEN MORE, BUT THEN AT VERY LOW SPEED. ACCUMULATOR WITH WINDER AND CONTROLLING SYSTEM MANUFACTURER: MATTHIJS (ELECTRICAL PART BY ELECTRO VANDEVELDE) YEAR OF CONSTRUCTION: 1999 OPERATING VOLTAGE: 3X380V CAPACITY ACCUMULATOR: +/- 50M UNIT FUNCTIONS INDEPENDENTLY FROM LAMINATING MACHINE AND SPEED VARIES FROM 0 TILL 50M (SPEED OF WINDING UP UNIT = SPEED LAMINATING MACHINE WHEN ACCUMULATOR IS EMPTY) SUPERSTRUCTURE FOR SUPPLY SECOND SUBSTRATE MANUFACTURER: MENZEL YEAR OF CONSTRUCTION: 2000 OPERATING VOLTAGE: 3X380V FUNCTIONS INDEPENDENTLY FROM THE LAMINATING MACHINE. SPEED REGULATION BASED ON A 0-10V (=0-15M) EXIT SIGNAL OF THE LAMINATING MACHINE MANUAL RIGHT-LEFT GUIDANCE OF THE SUBSTRATE. A SECOND AUTOMATIC PRE-GUIDANCE IS FORESEEN, BUT THE MOTOR DOES NO LONGER FUNCTION AND IT IS IN PRACTICE NOT REQUIRED BECAUSE THE ROLLS ARE ALWAYS WINDED STRAIGHT. A MEASURING ROLLER IS INCLUDED TO MEASURE THE TENSION OF THE SUBSTRATE. THIS MEASURING ROLLER DIRECTS THE MOTOR SPEED SO THAT THE ADJUSTING OF THE TENSION STAYS STEADY. IT IS EVEN POSSIBLE TO GO TO A +/- TENSIONLESS SITUATION. THE LINE IS MOUNTED ON A SELF-MADE PLATFORM EQUIPPED WITH A SIMPLE UNWINDING UNIT. KNOWN PROBLEM: PRESSURE ROLLER TO AVOID THAT THE SUBSTRATE “SLIDES” OVER THE BRAKE ROLLER IS WORN OUT, BUT IS IN PRAXIS NOT NEEDED. MOTOR OF THE PRE-GUIDANCE IS BROKEN (SEE ABOVE) MISCELLANEA SELF-BUILD ENTRY J-BOX WITH SIMPLE ROLL MEASUREMENT SEPARATE J-BOX FOR UNWINDING FROM DOCKS, SO THAT CAN BE LAMINATED IN THE POLE DIRECTION SEWING MACHINE MERROW TO MAKE FLAT SEAMS ON FINE/THIN FABRICS SELVEDGE CUTTERS ARE MOUNTED ON A SYSTEM SO THAT THE FABRIC CAN BE LEVELLED EASILY, EVENTUALLY CAN BE WINDED ON DOCKS. INCLUDING 2 DOCKS OF 2M30 OF WHICH 1 WITH FLAP BEARINGS CAN BE INSPECTED BUT NOT IN PRODUCTION MACHINE WILL BE DISMANTLED AT END OF NOV 2014 QUANTITY AVAILABLE: 1 Learn More

REFERENCE NUMBER: M-4136 SANTEX TENTER FRAME YEAR 2003-UP TO 3400mm – 3 ZONE – VERTICAL PIN – HOT OIL TYPE: SANTEX TENTER FRAME YEAR: 2003 WORKING WIDTH: 800mm UP TO 3400mm SPEED: 2 UP TO 20 M/MIN CHAIN: VERTICAL PIN CHAIN DRYER: 3 COMPARTMENTS DRYER LENGTH: 6 METERS MAX. TEMP.: 230° C HEATING: DIATHERMIC OIL OIL BOILER: GARIONI NAVAL TH 500 CAPACITY: 581 KW, MAX. TEMP. 350° C, NITROGEN COVERED TOTAL LENGTH NEEDED: APPROX. 20,000mm TOTAL WIDTH OF MACHINE: 6,200mm TOTAL HEIGHT OF MACHINE: 3,100mm ENTRY COMBINATION GUIDING CHAIN FOR A-FRAMES CORRECT POSITIONING RUBBERIZED ROLLERS AS INFEED UNIT WECO IMPREGNATION UNIT, CONTROL AND TANK ROLLER WITH LOAD CELL MAHLO WEFT STRAIGHTENER, TYPE: RFMC-10A 6 MEASURING HEADS, WW 4200mm OPERATION PEDESTAL OPERATION PANEL, MONITOR 1 UPPER INFEED ROLLER + 1 BENDED ROLLER E+L FABRIC INFEED VERTICAL PIN CHAIN 3 SECTIONAL DRYER (6 M) COOLING UNIT AT EXIT 2 CAMERAS VIDEO CONTROL STRETCH WORK: 2 PRESSING ROLLERS 3 HEATED DRAG ROLLERS WITH SINGLE DRIVE TEMPERATURE 80° C TO 250° C ON-WINDING UNIT FOR A-FRAMES ELECTRICAL CABINET QUANTITY AVAILABLE: 1 Learn More

J-5305 FINISHING PLANT FOR WORSTED AND WOOLEN SPLIT SALE POSSIBLE Learn More

M-6248 SANTEX DRYER YEAR 1997 WIDTH 2400mm

DRYING MACHINE
MAKE: SANTEX
WORKING WIDTH: 2400mm
YEAR: 1997
DOUBLE FOULARD
GAS-HEATED
NUMBER OF ROOMS: 5

MACHINE IS IN VERY GOOD CONDITION

QUANTITY: 1

Learn More

REFERENCE NUMBER: C-3854

SANTEX DRYER

MODEL: SANTASHRINK

3 CHAMBERS GAS HEATED

YEAR: 2003

QUANTITY: 1

Learn More

REFERENCE NUMBER: C-3853

SANTEX DRYER

MODEL: SANTASHRINK

3 CHAMBERS GAS HEATED

YEAR: 2001

QUANTITY: 1

Learn More